High Throughput Oligonucleotide Analysis Using the CombiSep Oligo PRO™ System .

High Throughput Oligonucleotide Analysis Using the CombiSep Oligo PRO™ System

www.combisep.com

Introduction

• Massive quantities of ssDNA and ssRNA oligonucleotides are produced daily to support the growth of genomic-related applications

• These DNA products need to be characterized to ensure proper sizing and acceptable batch-to-batch purity

• Traditional slab gel-based methods for characterizing DNA products are time-consuming, labor intensive, not readily automated, and provide relatively poor resolution

• While useful for assessing compound identity, Mass Spectrometry cannot quantitatively assess oligonucleotide purity due to size dependent variations in ionization efficiencies

• As a result, a bottleneck exists for characterizing the purity of ssDNA oligonucleotides

Capillary Gel Electrophoresis (CGE)

- +

UV

--

--

--

--

-

• Size-based separation of species possessing a constant mass-to-charge ratio (e.g., denatured SDS-protein complexes, ssDNA oligonucleotides, dsDNA)

• Separation medium is a gel-based sieving matrix; smaller sized species migrate faster

• Throughput for single capillary CGE methods range from 15 min – 100 min per sample; not adequate for high throughput quality control

Principles of MCE-UV Operation

• UV light passing through the detection window of a 96-capillary array is imaged onto a linear photodiode array detector

• Capillary inlets are arranged 8 x 12 for direct injection from 96-well sample plates• Capillary outlets are bundled to a common reservoir enabling pressure or vacuum to be

applied to the array• Samples are separated by the application of a high voltage with optional vacuum flow• 96 individual CE separations are performed in parallel with simultaneous UV detection

• CGE-UV is the method of choice for assessing oligonucleotide purity, providing higher resolution and superior quantification vs. slab gels.

• Label-free UV detection provides a low cost, toxic free alternative and improved quantification compared to fluorescent label approaches for ssDNA which may possess size and sequence dependent fluorescent labeling efficiencies

• CGE-UV advantages for characterizing oligonucleotide purity include low sample consumption, high resolving power, direct on-line UV detection and automated operation.

• A proprietary gel sieving matrix (Oligel) has been developed for multiplexed

operation. When analyzed at low M concentrations, single nucleotide resolution can be obtained from 10mer to 80mer oligonucleotide lengths, allowing identification of low level n-1, n-2, etc. impurities.

• Multiplexed CGE-UV provides a nearly 50-fold improvement in sample throughput over single capillary CE methods with a minimal loss in separation performance. A throughput of 96 samples/h is achieved for 80mer length oligonucleotides.

ssDNA Oligonucleotide Analysis by Multiplexed CGE-UV

Oligo PRO™ System (CombiSep, Ames, IA USA)

• Second generation 96-capillary array CE instrument• Fixed wavelength UV or visible detection• Slide-out stage accommodates four 96-well plates (1 waste, 1 buffer, 2 samples)• System can be interfaced to a robotic arm for unattended well plate exchange

Automatic Tray Handler

Sample Tray #1

Sample Tray #2

Waste Tray

Buffer Tray

Front Access Panel

Capillary Array Cartridge

LampHousing

HV Power Supply

Syringe Pump

Optical Platform Housing

Capillary Array Detection Window

Inside View of the Oligo PRO™ Instrument

High Pressure Pump Option for Oligonucleotide Analysis on the Oligo PRO™ Instrument

Oligel MatrixCapillary Conditioning

Solution

A/B Switching Valve

• Pressures up to 400 psi can be applied to the capillary array

96-Capillary Array Viewed from Detector Position

Capillary Outlets(12 Bundles of 8 Capillaries)

Detection Window(Polyimide coating removed)

Capillary Inlets(Arranged in 8 x 12 Format)

Capillary Array Inlets Viewed from Below

• Direct injection by voltage from 96-well plates• Working injection volume typically 100 l

Image of 96-Capillary Array on PDA Detector

• Continuous measurement of UV intensity simultaneously in all 96 capillaries• Absolute light intensity does not have to be equal as the relative absorbance is

measured in each capillary

Oligo PRO™ Specifications for Oligonucleotide Analysis

Detection • Fixed wavelength UV at 254 nm using mercury lamp and narrow band pass filter

Capillary Array Dimensions • 75 m i.d., 200 m o.d.• Effective lengths 40 cm to 55 cm; ~20 cm fixed length from detector to outlet

Sample Preparation• Typical oligonucleotide working concentration of 1-5 M for a standard EK injection

Sample Injection• Electrokinetic; 100 L working injection volume; -2 to -5 kV for 10 - 20 sec

Multiplexed CGE-UV Operational Conditions• Typical total operating current 0.4 – 0.6 mA (<6 A/capillary)• Field strength ~150 V/cm• Forced air capillary cooling at room temperature

Contains proprietary mix of polymers and 8 M urea to fully denature oligonucleotides

Low UV background at 254 nm

Low current generation (< 5 A per capillary at 150 V/cm)

Self-coating of capillaries to reduce EOF

Low viscosity to facilitate faster pumping speeds

Single base resolution from 14 – 80mers

Relatively fast separation speed (80mers in ~1 h)

Features of Oligel™ Separation Matrix for Multiplexed CE-UV

Sample: Desalted 14,15 - 19,20 – 29,30 – 39,40 – 59,60 – 79-80mers

Concentration: 1.5 µM (14-30mers); 0.1 µM (39-60mers); 0.2 µM (79,80mers)

CGE-UV: E = -170 V/cm; Sample injection = -5 kV, 10 s; UV = 254 nm

14,15mer

19,20mer

29,30mer

39,40mer

59,60mer

79,80mer

Separation Resolution of Oligel Sieving Matrix

96-Capillary Separation of 14-80mers Using Oligel™ Matrix

Analysis of Unmodified (Top) and Amine-modified (Bottom) 70mers

Sample: Desalted Unmodified, Amine-modified 70mers

Concentration: 5 µM Injection: -3 kV, 15 sCE Run: -140 V/cm, 70 min

A:B=1:9

A:B=1:1

A:B=1:3

Separation of Various Ratios of Unmodified (A) to Amine-modified (B) 70mers

Sample: Desalted Unmodified, Amine-modified 70mers

Concentration: 5 µM Injection: -3 kV, 15 sCE Run: -140 V/cm, 70 min

Sample: Desalted, Amine-labeled 70mersConcentration: 8 µMSample Injection: -3 kV, 10 secCE Run: -150 V/cm, 70 min

Multiplexed CE-UV Analysis of Amine-modified 70mers

Characteristics of Gel Matrices Used in CGE

• Chemical Gels– Cross-linked, chemically linked to the capillary wall: not replaceable– Well-defined pore structure but pore size cannot be varied after

polymerization– Heat sensitive– Particulates can damage gel matrix

• Physical Gels– Not cross-linked, not attached to the capillary wall: replaceable– Entangled polymer networks of linear or branched hydrophilic

polymers– Dynamic pore structure– Heat insensitive

Permanent coating vs. Dynamic coating

Why: for non-cross-linked gel, EOF reduces separation efficiency

How to reduce the EOF?Permanent coating:– Chemical bonding to the capillary wall– Non-replaceable– Limited life time

Dynamic coating:– Physical bonding (hydrophobicity and charge)– Replaceable

High Pressure Pump Option for Oligonucleotide Analysis on the Oligo PRO™ Instrument

Oligel MatrixCapillary Conditioning

Solution

A/B Switching Valve

• Pressures up to 400 psi can be applied to the capillary array

Operation Flow Chart

Fill Gel Separation Separation Separation

(400 psi)(3 to 4 hours)

(~1 hour)

Once a week: Conditional Solution + Gel Fill (~4 hours)

Total of ten separations

Oligonucleotide Analysis : Reagent Cost per Sample

DN-415-0250 Oligel ssDNA Gel, 250 ml

List Price: € 280 Volume Consumed 20 ml/day + 10 ml/run

Plates per Day 6

Samples per Day 576

Cost per sample (Est.) €0.15

Plates per Day 10

Samples per Day 960


DN-465-1000 ssDNA Oligel Buffer, 1000 mL

List Price:€102 Volume per Day (ml) - up to 10 runs 106

Samples per Day (6 plates) 576




DN-475-1000 Capillary Conditioning Solution, 1000 mL

List Price: €153 Volume (ml) per week (Est.) 250





Total Reagent Cost per Sample (6 plates/576 samples/day) €0.18

Total Reagent Cost per Sample (10 plates/960 samples/day) €0.16

Oligonucleotide Analysis : Capillary Cartridge Cost per Sample

Calculation assumes :1. cost per capillary array = €61942. Operating days per week = 5 days/wk

Samples per day Plates per day

Capillary Lifetime (weeks)

12 16 20 25 36 52

96 1 1,08 € 0,81 € 0,65 € 0,52 € 0,36 € 0,25 €

192 2 0,54 € 0,40 € 0,32 € 0,26 € 0,18 € 0,12 €

288 3 0,36 € 0,27 € 0,22 € 0,17 € 0,12 € 0,08 €

384 4 0,27 € 0,20 € 0,16 € 0,13 € 0,09 € 0,06 €

480 5 0,22 € 0,16 € 0,13 € 0,10 € 0,07 € 0,05 €

576 6 0,18 € 0,13 € 0,11 € 0,09 € 0,06 € 0,04 €

672 7 0,15 € 0,12 € 0,09 € 0,07 € 0,05 € 0,04 €

768 8 0,13 € 0,10 € 0,08 € 0,06 € 0,04 € 0,03 €

864 9 0,12 € 0,09 € 0,07 € 0,06 € 0,04 € 0,03 €

960 10 0,11 € 0,08 € 0,06 € 0,05 € 0,04 € 0,02 €

1248 13 0,08 € 0,06 € 0,05 € 0,04 € 0,03 € 0,02 €

1920 20 0,05 € 0,04 € 0,03 € 0,03 € 0,02 € 0,01 €

Other Technologies

• Slab Gel• Single column capillary electrophoresis• Mass Spectrometers• HPLC

Slab Gel

• Multiple samples analysis• Good resolution• Very labor intensive• Difficult to document the image• Semi-quantitation • Long separation time• Acrylamide

Single Column Capillary Electrophoresis

• Similar resolution as in Oligo PRO™• Better reproducibility• Slow (~96 times slower)• Sample cost: higher due to the use of coated capillary (limited

life time)

Mass Spectrometers

– MALDI (matrix assisted laser desorption ionization)• Size determination up to 60’mers• Difficult for quantification

– Electrospray ionization • Size determination up to 120’mers• Relatively slow: a couple minutes per sample• Difficult for quantification

– HPLC-MS• Size determination & quantification• Slow: half hour to an hour per sample

HPLC (Ion Exchanged Chromatography)

• Quantitation measurement• Separation up to 40’mers• Slow: half hour per sample• Separation not completely based on size• Better reproducibility

Impurity Screening of an Amine-modified 70mer Sample

• Approximate % Purity of main peak is 39.1%

CombiSep and IDT Poster Co-Winners of Best Poster at Tides 2005 Conference

The poster titled “Comparisons between Multiplexed, Absorbance-Based Capillary Electrophoresis, Capillary Electrophoresis, and Ion Exchange Chromatography for Analysis of n-1 Oligonucleotide Impurities” by Wei Wei, Ho-ming Pang, Dennis Tallman, and Jeremy Kenseth of CombiSep, Inc and Lisa Bogh of Integrated DNA Technology was recently selected as the co-winner of the best poster at Tides 2005. The Tides Conference is an industry event for manufacturing and development of oligonucleotide and peptide products. The meeting was held May 1st – 5th, 2005 at the Boston Convention & Exhibition Center.

The poster award was sponsored by BioProcess International. The selection criteria was based on novelty, applicability, and clarity of data presented.

Co-Winner Best Poster at Tides 2005

50:50 Mixture of 29mer:30mer by multiplexed CE-UV, CE-UV, and IEC

• IEC method was unable to provide resolution of n-1 species

Multiplexed CGE

Single Capillary CGE

Ion Exchange HPLC

70 min = 96 Samples

25 min = 1 Sample

25 min = 1 Sample

50:50 Mixture of 39mer:40mer by multiplexed CE-UV, CE-UV, and IEC.

• IEC method was unable to provide resolution of n-1 species

Multiplexed CGE


Ion Exchange HPLC

70 min = 96 Samples

27 min = 1 Sample

26 min = 1 Sample


• All methods could provide resolution of n-1 species

Multiplexed CGE


Ion Exchange HPLC

70 min = 96 Samples

30 min = 1 Sample

28 min = 1 Sample


• IEC method was unable to provide resolution of n-1 species• IEC provided no n-1 resolution at 70mer, 80mer lengths• The CGE methods resolved n-1 at 70mer, 80mer lengths

Multiplexed CGE


Ion Exchange HPLC

70 min = 96 Samples

38 min = 1 Sample

30 min = 1 Sample

Separation of 36mer and 37mer ssRNA Oligonucleotides

Sample: Two RNA oligonucleotides (36mer, 37mer) were obtained from IDT. The 36mer sequence was 3’-CAGGGACAAGCCCGCCGUGACGAUCUCUAAACAAGC-5’; the 37-mer had an additional A residue on the 3’ end. Samples were diluted to ~ 1 M in water.

Capillary Array: 75 m i.d., 150 m o.d.; 55 cm effective/80 cm total length

CGE: E = 150-170 V/cm. Sample injection: -2 kV, 15 sec

Oligo PROTM Analyzer System

• Multiplexed CE-UV system designed and optimized specifically for oligonucleotide analysis and QC

• Improved ease-of-use and automation

• Enhanced data analysis and report generation capabilities designed with feedback from scientists directly engaged in oligo production

• Launched in May 2006

Summary

• Multiplexed CGE-UV provides a powerful method for oligonucleotide purity analysis, providing superior resolution, throughput and automation compared to slab gel methods

• Only minimal sample preparation is required for analysis

• The developed Oligel™ matrix is capable of achieving single base resolution from 14-80mers in about 1 h

• Multiplexed CGE-UV provides much higher sample throughput and superior resolution to HPLC methods. The standard IEC method could not resolve n-1 species at 30mer, 40mer, or above 60 mer lengths

• RNA oligonucleotides as well as dsRNA duplexes can be analyzed for purity in addition to DNA oligonucleotides

Details of Disruptive Technologies

Contacts

William Amoyal (Sales and Marketing Director)

Franck Do Vale (Technical Director)

Disruptive Technologies

3 Allée des Camélias

94440 Villecresnes, France

Mobile: +33 (0)6 98 64 98 81

Email: [email protected]

Web: www.disruptechno.com

mailto:[email protected]

http://www.disruptechno.com/

High Throughput Oligonucleotide Analysis Using the CombiSep Oligo PRO™ System .

Documents

Transcript of High Throughput Oligonucleotide Analysis Using the CombiSep Oligo PRO™ System .