High pass filter
-
Upload
anirban-bhowal -
Category
Devices & Hardware
-
view
267 -
download
9
description
Transcript of High pass filter
![Page 1: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/1.jpg)
BY ANIRBAN BHOWAL
RAHUL JAISWAL SHARAD KUMAR
![Page 2: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/2.jpg)
QUASILUMPED ELEMENT
• Microstrip line short section and stubs whose physical length is smaller than λg/4 are used for microwave realization of lumped parameters in microstrip filter structures.
• These are termed as quasilumped elements.
• They can be also termed as lumped elements if their physical length is smaller than λg/8.
![Page 3: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/3.jpg)
High impedance short line sections
If l < λg/8 then,
![Page 4: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/4.jpg)
Low impedance short line sections
If l < λg/8 then,
![Page 5: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/5.jpg)
• A transmission line of characteristic impedance Zu has a ABCD matrix given by:
Interconversion formula
![Page 6: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/6.jpg)
Quasilumped high pass filters
• Highpass filters constructed from quasilumped elements may be desirable for many applications, provided that these elements can achieve good approximation of desired lumped elements over the entire operating frequency band.
• If the size of any quasilumped element becomes comparable with the wavelength of an operating frequency, it no longer behaves as a lumped element.
• The simplest form of a highpass filter may just consist of a series capacitor,which is often found in applications for direct current or dc block.
![Page 7: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/7.jpg)
Continued…
• Highpass filter can be easily designed based on a lumped-element lowpass prototype such as one shown in figure, where gi denote the element values normalized by a terminating impedance Zo and obtained at a lowpass cutoff frequency Ωc.If we apply the frequency mapping
Where Ω , ω=angular frequency variables for low pass and high pass filter respectively ωc=cutoff frequency of high pass filter Ωc= cutoff frequnecy of low pass filter
![Page 8: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/8.jpg)
Transformation from low pass prototype into high pass filter
Fig. (a) represents a low pass prototype filter and fig. (b) represents high pass filter transformed from low pass prototype
![Page 9: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/9.jpg)
• Series inductive element in the lowpass prototype filter is transformed to a series capacitive element in the highpass filter, with a capacitance
• And shunt capacitive element in the lowpass prototype is transformed to a shunt inductive element in the highpass filter, with an inductance
![Page 10: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/10.jpg)
EXAMPLE
• GIVEN DATA:- • Cutoff frequency:- 1.5GHz • Passband ripple:- 0.1dB • Source/load impedance:- 50 ohms • A Lowpass prototype with chebyshev response is
chosen. Element values are go= g4 =1 g1 =g3 = 1.0316 g2 = 1.1474 Ωc=1
![Page 11: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/11.jpg)
Calculated values
![Page 12: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/12.jpg)
Design parameters
• Dielectric constant=2.2 (RT/D 5880)
• Substrate thickness=1.57mm
• Cutoff frequency =1.5Ghz
![Page 13: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/13.jpg)
![Page 14: High pass filter](https://reader033.fdocuments.net/reader033/viewer/2022042507/55967d231a28abdb368b4719/html5/thumbnails/14.jpg)