High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual...

9
Model No. Description Input Voltage Min Load Output / Max Load High Bay Fixture Mount Sensor Options The fixture mount series high bay PIR occupancy sensors are designed specifically for use in commercial and industrial applications such as warehouses, distribution centers shop areas, parking garages, and assembly areas. The high bay lens supports mounting heights up to 40ft while the low bay lens supports mounting heights up to 20ft. Both lenses provide 360° coverage and special covers are available to adapt this detection pattern for use in aisles. Applications 120-277VAC, 50/60Hz None 800VA @ 120VAC, 6.7A 1200VA @ 208/240/277VAC, 4.3A Each sensor package contains the following: 1 High bay sensor 1 Installation guide 1 ARM: Mounting arm* 1 Back cover** 2 snap-on chase nipples 2 mounting screws & anchors 1 HBL: High bay lens† 1 LBL: Low bay lens 1 AL1: End of aisle lens cover (180°) 1 AL2: Center of aisle lens cover The sensor detects occupant motion by comparing the infrared energy (heat) emitted by moving objects with the background space. Users can adjust sensitivity, time delay, and other settings via a dip switch (must remove the front cover to gain access). The photocell version can prevent lighting from turning on if adequate daylight is available. It is designed to turn lights on at 30±15lux and off at >100lux. Dual relay version can control two loads in the same fixture. This enables users to achieve bi- level dimming and can extend lamp life. Basic Features Digital passive infrared (PIR) sensor Input voltage: 120-277VAC, 50/60Hz IP65 rated version for wet locations Dual relay version Mounting height up to 40ft 4 lens options: high bay, low bay, center aisle, end of aisle Time-delay and sensitivity controls Photocell for daylight sensing LED indicator light UL listed E478046 How to Order Sensor Operation Suitable for indoor or outdoor use E478046 Accessories Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 PS-P1277-HB-FM PIR PS-P1277-HB-FM-L PIR w/Photocell PS-P1277-HB-FM-D PIR Dual Relay PS-P1277-HB-FM-LD PIR Dual Relay w/Photocell PS-P1277-HB-FM-W PIR, Wet/Low Temp PS-P1277-HB-FM-LW PIR w/Photocell, Wet/Low Temp PS-P1277-HB-FM-DW PIR Dual Relay, Wet/Low Temp PS-P1277-HB-FM-LDW PIR Dual Relay w/Photocell, Wet/Low Temp ***NOTE: ITEMS IN GRAY ARE NON-STOCKED ITEM. FOR LEAD TIMES PLEASE CONTACT NEXLIGHT AT 218-828-3700 1 *NOTE: Mounting Arm is not IP65 rated for outdoor use, therefore it is not included in the packaging for any wet location sensor **NOTE: The back cover is an optional accessory for indoor rated sensors. It provides a method for mounting the sensor to a J-Box. It is not required and cannot be installed on wet location models (therefore it is not included in those packages).

Transcript of High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual...

Page 1: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Model No. Description Input Voltage Min Load Output / Max Load

PSC-HB-I-FM-100 PIR basic

High Bay Fixture Mount Sensor Options

The fixture mount series high bay PIRoccupancy sensors are designed specifically foruse in commercial and industrial applicationssuch as warehouses, distribution centers shopareas, parking garages, and assembly areas.

The high bay lens supports mounting heights upto 40ft while the low bay lens supports mountingheights up to 20ft. Both lenses provide 360°coverage and special covers are available toadapt this detection pattern for use in aisles.

Applications

120-277VAC,50/60Hz None 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Each sensor package contains the following:

· 1 High bay sensor· 1 Installation guide· 1 ARM: Mounting arm*· 1 Back cover**· 2 snap-on chase nipples· 2 mounting screws & anchors· 1 HBL: High bay lens†· 1 LBL: Low bay lens· 1 AL1: End of aisle lens cover (180°)· 1 AL2: Center of aisle lens cover

The sensor detects occupant motion bycomparing the infrared energy (heat) emitted bymoving objects with the background space.Users can adjust sensitivity, time delay, andother settings via a dip switch (must remove thefront cover to gain access).

The photocell version can prevent lighting fromturning on if adequate daylight is available. It isdesigned to turn lights on at 30±15lux and off at>100lux.

Dual relay version can control two loads in thesame fixture. This enables users to achieve bi-level dimming and can extend lamp life.

Basic Features· Digital passive infrared (PIR) sensor· Input voltage: 120-277VAC, 50/60Hz· IP65 rated version for wet locations· Dual relay version· Mounting height up to 40ft· 4 lens options: high bay, low bay, center

aisle, end of aisle· Time-delay and sensitivity controls· Photocell for daylight sensing· LED indicator light· UL listed E478046

How to Order

Sensor Operation

Suitable for indoor or outdoor use

E478046

Accessories

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568

PS-P1277-HB-FM PIR

PS-P1277-HB-FM-L PIR w/Photocell

PS-P1277-HB-FM-D PIR Dual Relay

PS-P1277-HB-FM-LD PIR Dual Relay w/Photocell

PS-P1277-HB-FM-W PIR, Wet/Low Temp

PS-P1277-HB-FM-LW PIR w/Photocell, Wet/Low Temp

PS-P1277-HB-FM-DW PIR Dual Relay, Wet/Low Temp

PS-P1277-HB-FM-LDW PIR Dual Relay w/Photocell, Wet/Low Temp

***NOTE: ITEMS IN GRAY ARE NON-STOCKED ITEM. FOR LEAD TIMES PLEASE CONTACT NEXLIGHT AT 218-828-3700

1

*NOTE: Mounting Arm is not IP65 rated for outdooruse, therefore it is not included in the packaging for anywet location sensor**NOTE: The back cover is an optional accessory forindoor rated sensors. It provides a method for mountingthe sensor to a J-Box. It is not required and cannot beinstalled on wet location models (therefore it is notincluded in those packages).

Page 2: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM

Weight: 7.05 oz

Summary

Sensor Type Passive infrared (PIR); single load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity N/A

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP20

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.89 in

4.13

in

4.13 in

Detection Area

Not suitable for outdoor useEquivalent outdoor rated version: PS-P1277-HB-FM-W

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec↑ ↓ 80% ↓ ↑ ↓ 30 sec↑  ↑ 70% ↓ ↑  ↑ 1 min

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓:OFF ↑: ON

Max: Dia. 40ft Optimal: Dia. 13ft

Note: Mounting arm not available for wetlocation models.

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 2

Page 3: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-L

Weight: 7.05 oz

Summary

Sensor Type Passive infrared (PIR); single load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity ON @ 30lux, OFF @ >100lux

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP20

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.89 in

4.13

in

4.13 in

Detection Area

Not suitable for outdoor useEquivalent outdoor rated version: PS-P1277-HB-FM-LW

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Note: Mounting arm not available for wetlocation models.

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 3

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ PIR + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑  ↑ Photocell only↑  ↑ 70% ↓ ↑  ↑ 1 min

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓:OFF↑:ON

Page 4: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-D

Weight: 7.05 oz

Summary

Sensor Type Passive infrared (PIR); dual load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity N/A

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP20

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.89 in

4.13

in

4.13 in

Detection Area

Not suitable for outdoor useEquivalent outdoor rated version: PS-P1277-HB-FM-DW

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ Load 1 + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑ ↓ Load 2 + Photocell↑  ↑ 70% ↓ ↑  ↑ 1 min ↓ ↑  ↑ Photocell only

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓: OFF ↑: ON

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Note: Mounting arm not available for wetlocation models.

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 4

Page 5: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-LD

Weight: 7.05 oz

Summary

Sensor Type Passive infrared (PIR); dual load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity ON @ 30lux, OFF @ >100lux

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP20

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.89 in

4.13

in

4.13 in

Detection Area

Not suitable for outdoor useEquivalent outdoor rated version: PS-P1277-HB-FM-LDW

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ Load 1 + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑ ↓ Load 2 + Photocell↑  ↑ 70% ↓ ↑  ↑ 1 min ↓ ↑  ↑ Photocell only

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓: OFF ↑: ON

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Note: Mounting arm not available for wetlocation models.

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 5

Page 6: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-WSummary

Sensor Type Passive infrared (PIR); single load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity N/A

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP65

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

Detection Area

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Weight: 7.8 oz

0.50 in

1.56 in

4.13

in

4.13 in

Suitable for outdoor useEquivalent indoor version: PS-P1277-HB-FM

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec↑ ↓ 80% ↓ ↑ ↓ 30 sec↑  ↑ 70% ↓ ↑  ↑ 1 min

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓:OFF ↑: ON

Note: Mounting arm not available for wetlocation models.

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 6

Page 7: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-LWSummary

Sensor Type Passive infrared (PIR); single load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity ON @ 30lux, OFF @ >100lux

Operating Temperature -20° to 60°C

Storage Temperature -20° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP65

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

Detection Area

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Weight: 7.8 oz

0.50 in

1.56 in

4.13

in

4.13 in

Suitable for outdoor useEquivalent indoor version: PS-P1277-HB-FM-L

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 7

Note: Mounting arm not available for wetlocation models.

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ PIR + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑  ↑ Photocell only↑  ↑ 70% ↓ ↑  ↑ 1 min

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓:OFF↑:ON

Page 8: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-DW

Weight: 7.8 oz

Summary

Sensor Type Passive infrared (PIR); dual load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity N/A

Operating Temperature -40° to 60°C

Storage Temperature -40° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP65

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.56 in

4.13

in

4.13 in

Detection Area

Suitable for outdoor useEquivalent indoor version: PS-P1277-HB-FM-D

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 8

Note: Mounting arm not available for wetlocation models.

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ Load 1 + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑ ↓ Load 2 + Photocell↑  ↑ 70% ↓ ↑  ↑ 1 min ↓ ↑  ↑ Photocell only

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓: OFF ↑: ON

Page 9: High Bay Fixture Mount Sensor Options - NexLight...• IP65 rated version for wet locations • Dual relay version • Mounting height up to 40ft • 4 lens options: high bay, low

Wiring Diagram Settings Adjustment

Physical Dimensions

Assembly

PS-P1277-HB-FM-LDW

Weight: 7.8 oz

Summary

Sensor Type Passive infrared (PIR); dual load

Input Voltage 120-277VAC, 50/60Hz

Max Load 800VA @ 120VAC, 6.7A

1200VA @ 208/240/277VAC, 4.3A

Min Load None

Max Range (high bay lens) Dia. up to 80ft @ 40ft mounting height

Max Range (low bay lens) Dia. up to 40ft @ 20ft mounting height

Optimal Range (high bay lens) Dia. 25ft @ 40ft mounting height

Optimal Range (low bay lens) Dia. 13ft @ 20ft mounting height

Time Delay 10 sec to 20 min

Photocell Sensitivity ON @ 30lux, OFF @ >100lux

Operating Temperature -40° to 60°C

Storage Temperature -40° to 60°C

Relative Humidity 20-90% non-condensing Mounting

Fixture mount

IP Rating IP65

Color White

Warranty 5 years

Certifications UL/cUL listed E478046

0.50 in

1.56 in

4.13

in

4.13 in

Detection Area

Suitable for outdoor useEquivalent indoor version: PS-P1277-HB-FM-LD

HBL: High bay lens

LBL: Low bay lens

AL1: Center aisle lens cover

AL2: End of aisle lens cover

Max: Dia. 80ft Optimal: Dia. 25ft

Max: Dia. 40ft Optimal: Dia. 13ft

Phone: 218.828.3700 www.nexlight.com Fax: 218.824.1568 9

Note: Mounting arm not available for wetlocation models.

Sensitivity Delay Time Sensor Logic1 2 3 4 5 6 7 8↓  ↓ 100% ↓  ↓  ↓ 10 sec ↓  ↓  ↓ PIR sensor only↓ ↑ 90% ↓  ↓ ↑ 20 sec ↓  ↓ ↑ Load 1 + Photocell↑ ↓ 80% ↓ ↑ ↓ 30 sec ↓ ↑ ↓ Load 2 + Photocell↑  ↑ 70% ↓ ↑  ↑ 1 min ↓ ↑  ↑ Photocell only

↑ ↓  ↓ 2 min↑ ↓ ↑ 5 min↑  ↑ ↓ 10 min↑  ↑  ↑ 20 min

↓: OFF ↑: ON