Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp...
Transcript of Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp...
![Page 1: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/1.jpg)
Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s
Precision Op Amps group.
What is the difference between a CMOS, Bipolar, and JFET amplifier? When should you use one over another? When
should you use an amplifier with no input crossover distortion, and what is input crossover distortion? What about Zero-
Drift, Chopper, and auto-zero amplifiers? This presentation will help you understand how to quickly in the select the
right op amp based on technology type.
1
![Page 2: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/2.jpg)
2 2 •2 •2 •2
Texas Instruments offers a wide variety of Amplifiers for your application needs.
We offer High Speed Op Amps (>50MHZ Bandwidth), Low Power Op Amps
(<10uA of quiescent current). In addition we have both low voltage and high
voltage Comparators. Texas Instruments also offers Precision (<1mV input offset
voltage) Op Amps, General Purpose Op Amps (>1mV input offset voltage). For
the Audio applications we also offer Lower Power Audio and Haptics Amplifiers
along with Piezo Drivers. For Medium and High Power Audio we offer both
Linear and Class D type Amplifiers.
![Page 3: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/3.jpg)
In our presentation here we will compare Bipolar op amps versus CMOS & JFET
op amps. In addition the differences between CMOS and JFET will be shown.
We will start first with a reminder of how the different transistors (Bipolar, CMOS,
JFET) operate. The important input op amp parameters of Vos, Ib and Drift of
these key parameters will be defined. Different ways to trim input offset voltage
will be demonstrated. Noise, a key specification for many signal chain designs,
will be compared for JFET, MOSFET, and Bipolar op amps. There are several
types of input structures for op amps which we will compare and contrast.
3
![Page 4: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/4.jpg)
Op amp topologies use one of three different transistor types (Bipolar, CMOS, JFET) for their differential input pairs. A quick reminder of how these transistors behave will help understand the follow-on detailed discussion of op amp types. When the term bipolar, CMOS, or JFET op amp is used it is referring to the type of transistors used in the input differential pair (+/-input ) of the op amp. An NPN bipolar transistor is shown as a current controlled device. Both the CMOS and JFET devices are N-Channel and are voltage controlled devices.
The NPN Bipolar Transistor is a current controlled device. The collector current is equal to the base current times a current high gain factor called hfe. The emitter current is the summation of the collector current and the base drive current. Since hfe is usually high, Ib is small when compared to Ic. Therefore, Ie is about equal to Ic. A bipolar op amp will have transistor bases connected to its inputs and therefore require some drive current into these inputs.
The N-Channel CMOS device is a voltage controlled device. It can be viewed as a voltage controlled resistor in its linear region of operation such that the drain to source resistance or Rds_on is controlled by the gate to source voltage or Vgs. For a typical N-Channel device Vgs=0V turns it off and Vgs > 2V will begin to turn it on. A CMOS op amp will have transistor gates connected to its inputs and therefore require next to no input drive current since it is a voltage controlled device.
The N-Channel JFET device is a voltage controlled device. It can be viewed as a voltage controlled resistor in its linear region of operation such that the drain to source resistance or Rds_on is controlled by the gate to source voltage or Vgs. For a typical N-Channel device Vgs=0V turns it on and Vgs < -2V will begin to turn it off. A JFET op amp will have transistor gates connected to its inputs and therefore require next to no input drive current since it is a voltage controlled device.
4
![Page 5: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/5.jpg)
Here is a general op amp model that can be used for offset and bias current
analysis. The same model is used for CMOS, Bipolar, and JFET amplifiers. The
general equations used to determine the output error voltage from the bias
current and offset voltage are given for reference. Notice that the bias current
will interact with both the feedback network and the source impedance to
translate into an offset voltage. The input offset voltage, Vos, is modeled as an
error voltage in series with the +input. Vos is gained up by the non-inverting
gain of the op amp and appears at Vout as the error term, Vo_vos. The input
bias current on the +input, IB+, flows through the source resistance, Rs, which
creates an input offset voltage which is gained up to Vout as an error voltage,
Voib+. The input bias current on the –input, IB-, flows through the parallel
combination of R1 and RF. Think of Vout as a short for this calculation. IB- times
R1//RF creates an input offset voltage which is referred to the +input and gained
up to Vout as an error term, Voib-. The final error voltage at the output,
Vo_os_ib is the summation of all error terms (Vo_vos, Voib+, and Voib-).
5
![Page 6: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/6.jpg)
This shows a simplified diagram of the inside of the amplifier for both a bipolar
and CMOS amplifier. Here we are focusing on the input stage. Looking at the
bipolar device, the offset voltage is set as the mismatch of the base to emitter
voltage Q1 and Q2. If the transistors are perfectly matched, the Vbe values will
cancel out and offset will be zero. In practical cases, the mismatches generate
an offset voltage in the millivolt range. The resistors Ros1 and Ros2 can be
adjusted (trimmed) so to minimize the offset. In the case of bipolar amplifiers,
the offset drift is directly proportionate to the offset voltage. So trimming Ros1
and Ros2 minimizes both offset and offset drift. The trim of CMOS devices is
more complex. In the case of CMOS devices, offset drift is adjusted by trimming
R1 and R2. Next, the offset is adjusted by trimming Ros1 and Ros2. Thus,
CMOS devices require at least two steps to minimize offset and offset drift, and
in some cases additional iterations are needed.
6
![Page 7: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/7.jpg)
The OPA211 is representative of a high performance operational amplifier that
utilizes the attributes of a modern bipolar transistor technology to provide very
high dc, ac and noise performances. Typically, bipolar based op amps have
usable power supply levels up to 36 V, and sometimes higher. The OPA350 is an
example of a precision CMOS op amp. It is ideally suited for low-voltage, single-
supply applications where high electrical performance is required. Traditionally
CMOS amplifiers have been in the 5V supply and lower. Later we will see some
new generation CMOS op amps that are usable up to 36V.
7
![Page 8: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/8.jpg)
This slide shows the inherent drift of bipolar devices compared to CMOS
devices. In the case of bipolar devices the drift is linear and directly proportional
to the offset. In fact, for each millivolt of offset you will get about 3.3uV/C of
offset drift. So, a device with a 1mV offset would have a drift of 3.3uV/C. CMOS
devices are non linear and their drift can be unpredictable. Trimming CMOS
devices will require a two temperature test and an iterative multi-step trim.
In general, because of the different characteristics of bipolar and CMOS you can
expect to see better offset and offset drift in bipolar devices. This is not always
the case though as some CMOS devices go through a lot of effort to optimize
offset and for some bipolar devices offset may not be optimized. The point is
that it is easer to get low offset and offset drift using a bipolar technology. Later
on we will see some tricks used in CMOS processes to eliminate trim and get
lower offset and drift specifications.
8
![Page 9: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/9.jpg)
This slide shows what a real world laser trim looks like. At the top of the page is
a picture of an op amp die. Each wafer will have many hundreds or perhaps
thousands of die on a wafer. Specifically we show two resistors that are laser
trimmed on this device: quiescent current, and offset voltage. The resistors are
a thin film, like NiCr or SiCr. The laser is used to burn away or open sections of
resistance making the total resistance higher. This trimming can actually be
done as the device operates. So, for example, you can monitor offset voltage
and trim the resistor until the total offset is zero. Unfortunately, the laser
trimming action can disturb the circuit operation, which can introduce errors or
require very slow pulsed trimming. At wafer, the trimming may produce very
accurate results. However, the wafer is sawed into die and is packaged. This
process normally causes some shift in the offset so some of the accuracy is lost.
Note that laser trimming has been used for years, and may new methods have
been developed. So, some may think that laser trimming is obsolete. This is
not true, however, as this is the only practical way to trim bipolar circuits.
CMOS circuits can use package level trimming as we will see later in this
presentation.
9
![Page 10: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/10.jpg)
The OPA1612 and OPA320S are two op amps designed for very different
markets, but both rely upon thin-film resistor laser trimming to minimize voltage
offset and drift. The trimming is accomplished at the wafer level. An added
bonus is the quiescent current can be trimmed for an optimal operating value
when the op amp is at probe and under the laser.
10
![Page 11: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/11.jpg)
In package level trimming the device is trimmed after it is packaged. This has
the advantage of avoiding the packaging shifts that happen when die are
packaged. Package level trimming involves digitally communicating with the
device and blowing fuses that “trim” the resistor. In fact, the fuses will be read at
power up and the resistors will be adjusted by shorting out segments using
digital switches. Since most op amps don’t have a digital interface, the digital
communications generally occurs through the output of the device. By changing
the loading on the output you can create a digital pattern to program the device.
Note that after the device is programmed a “write protect” fuse is blown so that
you can never re-program the device. The big advantage of package level trim
is that it is done at final test where all of the packaging stresses on the die will
be accounted for.
11
![Page 12: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/12.jpg)
Here are examples of the OPA376 low-voltage and OPA192 high-voltage CMOS
op amps that use active electronic trimming techniques (e-trimTM) to reduce and
minimize their naturally occurring voltage offset and drift.
12
![Page 13: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/13.jpg)
Let’s look at the inside of CMOS and bipolar amplifiers again to consider the
difference in bias current across the technology. In the case of bipolar devices,
the bias current is from the base current of the device. This will very depending
on the process but often is in the range of 100nA. In the case of CMOS devices
on the other hand, the bias current is almost completely from leakage of the
input diodes. The input gate current is negligible as the impedance is very large
(Tera-ohms). Typical the room temperature bias current will be about 1pA. Thus
the bias current for a CMOS device is often 100,000 times smaller than that of a
bipolar device.
13
![Page 14: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/14.jpg)
One way to minimize the bias current for bipolar devices is a method called bias
current cancellation. In bias current cancellation, the base current of the input
transistors is monitored and an equal but opposite current is summed into the
input to cancel the bias current. Of course, it is not possible to perfectly cancel
the bias current so some residual current will remain. Typical circuits will get a
100x improvement in bias current reducing it from 100nA to 1nA.
14
![Page 15: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/15.jpg)
The OPA209 and OPA211 are both high performance bipolar input operational
amplifiers. The OPA209 includes input bias current cancellation circuitry, while
the OPA211 does not. It can be seen that the typical and maximum input bias
currents are significantly different for the two op amps. If keeping the input bias
current low is important in a low-noise application, then the OPA209 may be
choice. One clue to if a bipolar input device has input bias current cancellation
is that the input bias current will be approximately equal to the input offset
current.
15
![Page 16: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/16.jpg)
One thing to remember with low bias current amplifiers is the effect of IB over
temperature. In MOSFET amplifiers, the bias current can double every 10°C.
You can see in the example on the right with the OPA350 that the input bias
current increases significantly at temperatures above 25°C. If you only
considered the room temperature value of IB and then operated the amplifier at
elevated temperature, you would have significant errors. Notice that the vertical
axis of the plot uses a logarithmic scale.
With the bipolar amplifier, the initial input bias current at room temperature is
often large enough such that the relative change in input bias current over
temperature is minimized. You can see in the example on the left with the
OPA277 that the input bias current starts to increase at temperatures above
75°C, but note that the vertical axis uses a linear scale.
16
![Page 17: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/17.jpg)
The 1/f noise corner of an op amp is often considered to be a figure of merit.
The noise corner is the place at which the 1/f and broad band noise curves
interest or the bend in the curve. The 1/f noise corner is much higher for CMOS
devices. JFET and bipolar have comparable 1/f noise although bipolar is
generally somewhat better. In fact, the JFET input is often selected to provide
very low Ib with good 1/f noise performance. In other words with JFET, you get
good Ib performance like a CMOS device, with good noise performance like a
bipolar device.
The current noise is shown in the red box. Note that current noise doesn’t
always have a curve as current noise for FET devices is generally considered to
be flat over frequency. Also note that the current noise is substantially smaller
with CMOS and JFET devices than with bipolar devices. Finally, note that the
bipolar current noise may have a 1/f component that makes it much higher at
low frequencies.
17
![Page 18: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/18.jpg)
Here three high performance op amps that use the three key op amp
technologies, which we have presented, have their voltage noise density
compared. The OPA227 was shown in the previous graph to have the lowest 1/f
corner frequency and lowest voltage noise. Its noise performance is followed by
the JFET input OPA827 amplifier which is just slightly higher. The OPA350
voltage noise is considerably higher at 1 kHz compared to the other two
amplifiers, but is expected because of considerably higher 1/f frequency of the
CMOS process and design.
18
![Page 19: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/19.jpg)
For rail-to-rail input CMOS devices, the two input transistor pairs will have independent and uncorrelated input offset voltages. This usually means that the input offset will be different for the two different input pairs. Thus, when we transition from one pair to the other, the offset voltage will abruptly change values. The figure on the right shows an example of the abrupt transition in input offset voltage. The green region shows the Vos when the p-channel input pair is active for common mode voltages between -0.3V and 3.5V. The p-channel pair has an offset of about 100uV. The red region show the Vos when the n-channel input pair is active for common mode voltages between 4V and 5V. The n-channel pair has an offset of about -200uV. When the common mode transitions past 3.5V the offset transitions from 100uV to -200uV. The abrupt transition in offset can appear as distortion in the output signal, known as “input crossover distortion” since it occurs during the crossover from one input pair to the other.
Taking a closer look at the specifications table, you will notice that the common mode rejection is low if the entire common mode range is considered. In some amplifier specifications you will see two separate specifications for common mode rejection ratio (CMRR) in the two different regions. In these cases the CMRR of each independent region can be very good, but the overall CMRR may be degraded if you include the crossover distortion. When looking at a rail-to-rail op amp data sheet, the different regions over which the CMRR is specified can be helpful for determining the crossover region.
19
![Page 20: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/20.jpg)
The OPA703, a 12 V CMOS op amp, and the OPA314, a CMOS low-voltage op
amp utilize complementary N-channel and P-channel input differential pairs. The
graphs show the noticeable voltage offset shift that occurs as the input common-
mode voltage transitions from the region where the P-channel pair is active (N-
channel inactive) and then the N-channel pair becomes active (P-channel
inactive). For many applications this may not be an issue; especially, if that
portion of the CMV region can be avoided.
20
![Page 21: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/21.jpg)
What does crossover distortion look like? Let’s consider an example when the
amplifier is in unity gain and has the common mode transition near 4V. The
input is a sine wave centered on 2.5V with an amplitude of 4Vpp. Because of the
non-inverting configuration, the input signal is also equal to the common mode
signal. When the input signal transitions above 4V, the offset transitions from
2.5mV to -5mV. Although this is a fairly large offset shift, it is difficult to see it on
the output signal diagram. Zooming in at around 4V, however, allows us to see
the output distortion introduced by the offset shift. In many applications, this
crossover distortion is not as significant as in this example. As with any error
source, consider your error budget and decide if this error can be tolerated.
21
![Page 22: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/22.jpg)
Here we show a simplified representation of the charge pump used in the
OPA365. In this case, the charge pump boosts the supply voltage by 1.8V while
not needing to supply much current. This is enough to overcome the Vsat + Vgs
positive rail limitation on the p-channel input pair. One concern that often
accompanies charge pump circuits is that they use a switched capacitor to
achieve the voltage boost. The switching generates noise, but in the case of the
OPA365 the amount of noise is minimized by the very low ripple design.
Despite this, it is sometimes possible for the charge pump noise to affect the
behavior of the op amp. The charge pump in the OPA365 switches at 10MHz
while the bandwidth of the amplifier is 50MHz, so in lower gain configurations
the charge pump noise will be passed by the amplifier. Generally, the charge
pump noise is small relative to the broadband noise of the amplifier.
Also note that the charge pump signal can feed through the external power
supply. In this case, it can combine with other power supply noise sources and
create harmonics of the charge pump signal. For this reason it is best to use
proper decoupling on the op amp power supply pins. In some cases using a
ferrite between the amplifier and other sensitive circuits may also help.
22
![Page 23: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/23.jpg)
The OPA365 and OPA322 are examples of CMOS op amps that use a high
frequency, low-noise charge pump to generate a higher, internal dc voltage
source used to power the op amp input stage. Doing so allows the P-channel
inputs to operate over the entire input common-mode voltage (CMV) range
avoiding the crossover region offset shift that accompanies an input stage
comprised of complementary N-channel/P-channel differential pairs.
23
![Page 24: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/24.jpg)
Zero drift amplifiers with rail-to-rail inputs actually use the same complementary
n-channel and p-channel input configuration as shown earlier in the video, so
they do exhibit some degree of crossover distortion. However, the offset of the
amplifier is corrected by digital calibration, so the magnitude of the offset
transition and the crossover distortion is greatly diminished. We will examine
how a “Chopper” amplifier works in subsequent slides.
24
![Page 25: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/25.jpg)
Another way to minimize offset and offset drift is with a zero drift amplifier. Zero drift is a general term used for any amplifier that has an internal calibration method that minimizes offset and drift. There are two common types of zero drift amplifiers: chopper and auto-zero. The auto-zero amplifier samples the offset and uses this value to correct the error. We will not discuss the auto-zero further here, but just know that it has similar characteristics and specification to the chopper amplifier.
Before discussing the chopper amplifier let’s look at a standard two stage op amp internal structure (shown at the top of the page). The two stage op amp will have a very small differential input signal (Vin). This input is translated to a current by the transconductance stage. The second stage is a transimpedance stage and it converts the current back to a voltage by charging the miller capacitance Cc.
The chopper amplifier has the same two stages. The main difference is that the input and output of the first stage has a set of switches that flips the input signal once every calibration cycle. In the next slides we will see how this can minimize the offset and offset drift.
Finally notice the table compares uncorrected versus zero drift and laser trim methods. In general, the zero drift method gives the best drift performance.
25
![Page 26: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/26.jpg)
The OPAx333 series of CMOS operational amplifiers use a proprietary auto-
calibration technique to simultaneously provide very low offset voltage and near-
zero drift over time and temperature. It is a low-voltage, low operating current op
amp. The OPA2188 relies upon the same auto-calibration technology used for
the OPA333, but is processed on a HV CMOS process allowing for use with
supplies up to 36 V. Its operating current is higher to support lower noise, wider
bandwidth and faster slew rate than is obtained with the micro-power OPA333.
26
![Page 27: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/27.jpg)
These summary slides will provide a quick reference guide to the trade-offs in specifications
when considering CMOS, Bipolar, and JFET op amp topologies. We’ve used a simple system of
X and check marks to show the relative strengths and weaknesses of each topology. While there
is too much information to be read here, you can refer back to this slide set at your convenience.
First we have summarized the differences between input offset voltage, input offset voltage drift,
input bias current, input bias current drift, and input offset current.
Vos: CMOS, largest Vos, complex trim, unless Chopper or Auto-zero.
Bipolar, smallest Vos, laser trim only, simple trim
JFET, larger than Bipolar, laser trim only, complex trim
Vos Drift: CMOS, largest drift, complex trim, unless Chopper or Auto-zero.
Bipolar, linear drift, laser trim only, simple trim
JFET, larger drift than Bipolar, laser trim only, complex trim
Ib: CMOS, lowest Ib (pA)
Bipolar, high Ib, can be minimized with Ib cancellation (nA)
JFET, Lowest Ib (pA)
Ib Drift: CMOS, doubles every 10C, ESD diode leakage dominant (pA to nA)
Bipolar, small change over temperature (nA)
JFET, doubles every 10C, ESD diode leakage dominant (pA to nA)
Ios: CMOS, Ios comparable to Ib (but pA)
Bipolar, high Ib, can be minimized with Ib cancellation (nA)
JFET, lowest Ib, Ios comparable to Ib (but pA)
27
![Page 28: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/28.jpg)
Next we compare the broadband noise, 1/f or low-frequency noise, presence of anti-parallel differential input diodes, integrated digital logic, rail-to-rail input and output, and output voltage vs. load capabilities of the different topologies.
Broadband Noise: CMOS, largest noise
Bipolar, smallest noise
JFET, slightly larger than Bipolar, smaller than CMOS
1/f Noise: CMOS, largest noise, >1kHz 1/f frequency, Chopper can eliminate 1/f noise
Bipolar, lowest noise, 1/f frequency <10Hz
JFET, lower than CMOS, higher than Bipolar noise, 1/f frequency <100Hz
Anti-parallel differential input diodes: CMOS, may or may not be needed – check datasheet
Bipolar, generally required
JFET, generally not required – check datasheet
Integrated Digital: CMOS, yes for Auto-zero or Chopper or e-Trim
Bipolar, no
JFET, no
Rail to Rail Input: CMOS, yes
Bipolar, no
JFET, not common
Rail to Rail Output: CMOS, close to rail (i.e. 10mV)
Bipolar, within 200mV of rail
JFET, within 200mV of rail
Output vs. Load: CMOS, falls off quickly with load due to Rds_on
Bipolar, relatively flat until current limit
JFET, relatively flat until current limit
28
![Page 29: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/29.jpg)
We will spend the next few slides discussing some easy ways to help quickly
pick the right op amp for your application.
29
![Page 30: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/30.jpg)
The first selection criteria is to answer for your application what Voltage (Supply
Voltage) , Current (Quiescent Current), and Speed (Bandwidth) you will need to
meet your end design goals.
30
![Page 31: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/31.jpg)
After your op amp choices have been narrowed down by the 1st Criteria
Selection, you can continue to narrow your final choices by the 2nd Criteria
Selection Process.
For Voltage: Input Offset Voltage, Input Noise Voltage, Common mode Input
Voltage Range, and Output Swing.
For Current: Output Current, Input Bias Current, Input Current Noise.
For Speed: Slew Rate and Output Impedance (a key parameter for driving
capacitive loads or dynamic transient lads such as driving SAR ADCs)
For Other: Package, Single/Dual/Quad available, Price
31
![Page 32: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/32.jpg)
Before we end let’s take a quick look at additional resources on www.ti.com you
may find of interests.
32
![Page 33: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/33.jpg)
IF you are interested in further information on op amp process and topologies
consider these TechNotes.
33
![Page 34: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/34.jpg)
Also available on www.ti.com are additional training and support tools. TI
Designs offer comprehensive sub-system designs with calculations, simulations,
and measured real world results. TINA-TI is an easy to use, GUI based, full
featured SPICE simulator. A Parametric Cross-Reference to find similar TI
Devices by parameters to what you are using now. The WEBENCH Filter Design
is a powerful way to easily design Active Filters. The DIP Adapter EVM offers a
quick way to convert surface mount ICs to the standard dual in-line package
type for connecting wires to or installing on breadboard platform. Check out our
Amplifier Quick Search which uses Current, Voltage, And Speed to help simplify
the op amp selection process. For direct cross-reference by part number use the
TI Cross Reference tool. For quick building block op amp circuit ideas check
out the Analog Engineer’s Circuit Cookbook. For a universal Pocket reference
look at the Analog Engineer’s Pocket Reference. And finally for 24-hour or less
response to technical questions about Texas Instruments products use the E2E
Forum located e2e.ti.com
34
![Page 35: Hello, and welcome to the op amp technology overview ... · Hello, and welcome to the op amp technology overview, developed by Art Kay, Thomas Kuehl, and Tim Green of TI’s Precision](https://reader031.fdocuments.net/reader031/viewer/2022022806/5cd0e7aa88c993cb728bb415/html5/thumbnails/35.jpg)
35