Hector Posts Volume3

8/9/2019 Hector Posts Volume3

1/95

Hector's Posts Volume 3, 2nd Edition

Editor's NoteThis document contains the postings from mostly one individual, Hector Perez Torres, collected at theyahoo site: http://groups.yahoo.com/group/evgray/. Within are message numbers from 10,000 to 14,999,

the rest left to subsequent volumes. No doubt some very good messages have been missed, hopefullythese will be included in anotheredition.

Messages

#10025Re: Oh no he did it again (Intent) "open cards deck"

...o--- In [email protected], Matt wrote:

>> Hey guys,> I hope everyone here understands that I am just trying to help.

*************************************************Its better to do in on open forum as dangers can be forseen.

There Are still here some Elements that represent Uni,NIC,Gov,powerindustry, military , as there are elements that can help the helpers.

Kone pointed to A FACT RV as Other technology needs to be KNOWN bythe people ..

So a non Debunkable bullshit proff system is needed ( The DC carBAttery and identical inverter fixtures with the exchangeable loads.

Pretested in identical aplications & loads , if the IDEA is todemostrate RV & alternate Technology Then the MAIN issue is POWERMANAGEMENT ,the capability to properly use energy resources and createnew ones (OU) zpe whatever and its aplication to standard equipment(were everry inventor in the last 50 years had failed to do )

If there is a LENZ less generator out there RV can drive it,as it onlydraws what the generator draws (in some instances less) and MUCH lessif generator is OU, (Many here understand that now ) and to make itwith parts & pieces from the Hardware existant parts got the Uni andDebunker community mentaly mad . (debunk That )

conversations are sometimes overheard and relayed to me ...

A big shot told an associate , they were better off paying me abillion dollars and having an army of hot bitches to dry me up like a

prune than what is needed to eliminate RV from public eye (at thispoint). (they can kiss my ass)


2/95

So thats the key (publicity) and show people how to make it fromstandard motors ...

As a fact is you can wire 0ne phase motors to 460 VAC you can run likeRV vectoring the START phase at proper angle (45deg) , will be a bitless effective than a 90DEG 3ph force vector but i will be effective ,

all 1 PH motors can be run RV mode ..

Put this in compilation...

More:120VAC motors can run RV with 28VAC just requires x4to x6capacitance run oil, start litic (to lower price cost) that means in24 VOLT dc battery systems you can run a 120VAC motor DIRECTLY FROMTHE BATTERY DRIVING IT with IGTBs BIASED H network lowering cost ofintegrated inverter systems in same motor to be run directly from DCas DC brushless RV motor (PHIL take note) "direct motor driver" ...

I just hope the grants flow in then I can go to Anty gravity and othersweet things I bet you can do with Off the shelve designed stuff ...

One of my dreams is to put out the home made (UFO)(car industry cankiss my ass).****************************************8Tips, is self run , its RV initialized Uses coanda-implosion closedloop and can run 11 years with no maintenance and it will indicatewith a red light when it needs it ( a ball bearing set change )And is shit kiss simple to make.As RV it will work , fact is everithing I envision can and will dowork as I use LAB test to confirm everry step.

Other thing is Home power by low cost suckamatrons , I just hope AKoil does not get Nuked and they put them out ...

But if they dont then RV comes out again as initiator and homemadeturbines will have to do.(Some vaccum cleaner forensics lab workneeded here) ,learning that sucking is better than blowing in energythermodynamic transformation is vital..

I think that the BIG feudal lords must get the message that people aretired of this shit system they created ,and that they either change orat the proper time they will be logisticaly and physicaly destroyed.

That is a promise ...

AMEN!

Hector (:B

#10333


3/95

Re: BCSRC test result

Again to REPEAT the gospel ...

Pulselenght and amplitude define the Saturation character of your

transformer core , you can have at a given pulselenght an increasein CEMF voltage as logaritmic Wave timeframe Equals a fundamental orharmonic were transformer laminate or core more easy transfers

potential from 0 point energy ZPE, the resultant CEMF pulse candiffer in time & space being impedance mismatched to source ,theresult is under OU any time ...

I think all of you must go back to TESLA coil design and Spark Gapsand its relation to EMA4 patent were the aspect of my statements can

be seen in figure and in written word within that same patent .

The AC input in a tesla coil as set in LC (resonant) and the sparkgap staired discharge I so much mention, the 60CPS to 128Kcpstransformation that occurs and the associated energy amplificationwithin that circuit must be understood else like a yoyo ,ZPE isthere then as you try to use it you dont have it, as it died amonga series of aplication errors within the circuit ...

Theory is one thing , aplication is another ... that is why anintuitive tinketer can have an edge over the doctorate nasa orCaltec theorist .. (the 2 must mend in one )

Hector

#10702Re: CF

R must limit C tensor if using 2X C if closed loop C=(C/2) x 2

remember R + C creates Varactor effect were frequency shifting

occurs .

In dioded HALF tank C is same as in FULL LC compensated for initial0 point state to max relative current induction in L ,

That is from a PM source induction, C is seen as a Solid conductorto wave ,asuming instant pulse (inductive to be transformed ) intocapacitive potential (joule) the power is maximal at Half cycle1/2 wavelenght but same pulselenght so we have to sum 2 pulselenghtvectors to sum of end product of c1 + c2 at final stage and addingthe 1.618 logaritmic gain ... in AC electrolisis is LCk k=

capactrode containing water, water as being recombinant transformerHeat out sums heat in as it recombines augments its energy untillattains cold fusion ..


4/95

The frequency is electron spin harmonic to molecular resonance2.450Ghz at 1.725 cps hypersignal tensor .

In a sense to be understood better you have to RV the water moleculetaping to its natural transformation frequencys

Parameters as glass dielectric constant its linear tensor relativeto harmonics within the plates and all electric hardware must beconsidered as not to DAMP the energy RADIATED from the sonofusedwater ,many things can be done just be carefull not to overdriveyour fish tank ... and (beware of getting near heavy lead pipes)wile having strange or uninvited visitors ...

Hector :)

#11026Re: Seiki S, The Principles of Ultra-Relativity PDF

Seike formulations are 300 years ahead of this timeline,Ash asked mein what page is the reference to RV relation, sinse first ARK pagethe backgrownd of the page contained the ROTARY phase kaweyama model.

RV is the physical demostration of this principle and all seike workis related to it Why he did not use 3 PH motors to demostrate this

principle I dont Know, maybe it was the dangers involved creatingphysical hi power rotating self oscillating engines ..

A NOTE :

In some Motors set in wye feeding pure DC to L center and capacitor(C) being negative fed to tripleflux wye center flux creates rotaryfield with infinite acceleration ...

Like Konehead motor tendency is to accelerate toward infinity

creating its own incremental harmonics in a self cycloconvertingeffect .

Just be carefull with the Toys .... ^_^ !

conditions to create this effect are critical in adjustment ...

But SEIKE clearly explains self rotary effect ...(Easy) A,B,C isPHASES ....

Hector :)



5/95

RV needs to break the 24 LAW rule

Up to date 23 does not suffice to break the collective barrier tomaterialize it from 4rth dimension coordinates to physical reality .

AB,BA,CA Ash look for that in seike formulations , your eyes willopen as you realize its 3 phases .....

Does Abracadabra tells you something in cabala ...?

The star of david is a moevious doble delta superconductivetripleflux reactor core.

The oldest and most advance technology is based in symbols, lean tosee seikes formulations in 4D construct they become clear as water .

The throne is the CENTER of POWER the SERVANTS hi and LOW are thephases within a looped hyperwave system that transfer energy statesfrom one level to the other ..

The POEMS are the key to ZPE transform ,and is evident what he wroteis too advanced to be of this timeline or this world .

Interpret were he mentions the aperance of RV ... ( the other place )Fact is RV works ,and FACT is Seike work corelates to RVdirectly ,for reason why he did not enter RV directly on its ownthere is no answer , maybe he was the judge and he let me to be theexecutioner to finish off retrograde physics concepts with a physicalworking model, fact is any true scientist may had tried hisformulations using a 3 phase motor , but I think they got mind biased

by the UFO toys pictured in his first books and they rejected itbeing ignorant assholes ...

Their loss my gain ..... (And yours)

Its 7 years of telling Seike Work , Norman Wootan Work, Bearden,Sweet Floyd (VTA ) ,bedini , Newman and many others have a Common

base ,. Seike Book is the final PIECE ...

Potato management is next step .... ( get into the sea) "the lab"

Hector :)

#11028gravitic relation

The self spining of delta wye seike model responds to a gravitic spiralflow component (as coreolis electrical force) being constructed a

Rotary Engine made to accelerate over the Spin 4D vector G (gravity)enters NEGATIVE state as rotary transform vecomes reverse flow in timerelative to gravitic one ...


6/95

Simple ...

More simple as you have RV "GATE" to enter the portal...

Hector :)


Have to correct on resistor issue its impedance at 50 ohmsRF ... ,can be much lower in hi Q modes , 500Ohms for hi voltagehi impedance near no lenz load system ...

RV at no load exedes 500ohms impedance in many cases..

Hector

#11071

Re: capacitor value calculation

If you are able to match and use the ferros LC crosscurrents intobattery feeding ferros with bandpass coupling capacitors fromtripleflux ones you got something to awe at ....

I have stated that a battery is nothing more than a BIG farad liticwith limited discharge capacity but it does not mean it can not becharged like one with a DC tensor or vector from a Hi Q low impedanceHi current resonant LC .

The issue is Impedance matching (Amplitude) being most significantaspect on OU management of resonant elements relative to batteryamperage under OU states,,

Note :

It was public info here to Use big farad capacitors andmegacapacitors as battery substitute ......

#11079Re: Robert Calloway and Tesla spark radiant energy

I think I already gave the right information on this ..

One impedance to saturate and other impedance to capture ...

Even SEIKE wrote about it ...


7/95

Hector :)

#11088Re: Magnetic field lines

Proff off that A white/black tv put a magnet on the TV screen

it makes electrons go in spiral reverse poles the spiral reverses.

Its aether flow (bidirectional ) as Hurricane winds one layer spinsin other spins out in counterrotating spirals but in magnet is withinsame dimensional planes ..

Think in 4d then you will get it easy ..

Hector :)

#11107Re: series wound coil antenna

RV reverse induction operates as RF amplitron device ...

(not first time I mention it ) nor it be the last

Its a rotary field ... (virtual Phases & virtual amplification like atibetan glass bell ...

Its a simple 3 phase circuit and a few capacitors but it will createthe greatest electrical engineering revolt in the history of science.

Hector :)

#11172Re: RV usage -[john]

I will Answer it ....

The answer is a green laser pointer with a 20,000 range ($65 USD)when they begin spraying just point it as to PAINT plane and activatethe missile targeting detectors , as they turn off the sprayer youstop lASER painting them .. be sure not to do it closer on aproach asnot to damage anyone eyes ... over 5,000FT distance laser light

bothers but is not harming to the eyes ... NEVER do it on a landingaproach as it is a crime as it can affect airplane operation blinding

pilots and harming passenger eyes ,use less than 5 Milli Watt lasersonly as not to break any law .. FAR away .. ! green laser looks likea freaking sun from 10,000 feet away ... Try it !

Its a good way to protest chemtrails ... laser painting any planethat does it .... Some of the planes anty missile flare guns begin


8/95

shooting away if painted with red laser modulated in amplitude withRock music ..

MUHAHAHAHAHA ! ^_^ !

Have fun .... ( statements avove do no represent relation to any

event ) they are the result of CIA agents anonymal info leaks ininternet forums ....

AMEN !...Hector

#11181Re: Squealing pigs

http://groups.yahoo.com/group/EVGRAY/files/A.R.K%20%20%20FILES%

20/Reactor Core .gif

MM I forgot to mention, the looping schematic (Basic) is in the Filessection ..

Its just a matter of time everrybody will be able to loop ...

A lot of you already pealed the potatos in salt water ...

It may be soon everyone will taste paradise ...

Feels so good when something is replicated as is ment to be ...

(And it Works ) as tested and predicted ...

Tip , my postings reveal the impedance relation needed for loopingthe reactor core , remember its RF not standard book electrical poweryou are dealing here , reactor core needs EMP to initialize motivatorloop , regulating is nessesary in order to avoid destructive power

increments ( meltdown looping )

Remember All the posted material here was already tested in vitroand is given in a way only replicable to thoose doing the experimentsas they learn the method ....

OU is clearly demostrated already ... the following steps are loopingand power extraction ...

But as already told , its simple as hell once you do it andunderstand it ..

The only problem is the Human greed and unmeasured egoistic ambition,Reactor core can save or destroy the world , but its positive outcome


9/95

relies in the persons building this devices and making experiments ..

Goin private & greedy or public & create a new society (with freeendless ZPE energy).

With this made public I had verified my status as the most (feared

man in Human History) second to Einstein with his atomic bomb gift.

Well I got a few seconds fame in the fabric of time and space .

Ufos and future time machines use this same basic circuit I gave youhere Just polarize and impedance match correctly as you have alreadythe primary basic steps (creating ZPE) "OU" .

Enjoy it :) (time is already out)

http://groups.yahoo.com/group/EVGRAY/files/A.R.K%20%20%20FILES%

20/Reactor Core .gif

Hector :)

#11238Re: another big waste

In PM RV goes to FULL HP ..

In PM turbine mode it EXEDES plate rated HP ..

But with No fucking money to demostrate models or protect the Freedomain is a loss of time ....

So Get ass wipes clean well lips and kiss the devills ass ,& wait forJesus to drop out of heavens .

AMEN !

#11287Re: Squealing Pigs.

The problem With the OU back to same source is crossvectoring, callit electron inercia memory, separating and delivering as JOULE

potential solves the problem as this inercial memory dissapears aselectrons are reduced to a pure capacitor charge potential VoltAmpere second (Joule) I was thinking once on using chemicalequilibrium assisted tripolar battery using the negative electronmemory as migration element to charge a third pole ,maybe a chemistwith proper funding can figure this one out ,specialy with newsupercapacitor chemistry at hand, Power factor here makes batterymemory think the electrons goin to it are far more powerfull than

they are so the chemistry reacts to it as charge .

Call that Suckering the battery ( In a sense ) with virtual OU power


10/95

RF ( radiant energy ) 4 stage inverting can also do that using a 3rdstage to valance the crossvector impedance issues ..

Problem resides fordward Power pulse is in different impedance matchthan the recovered CEMF so the 2 cannot co-exist in same environmentunless you use bandpass diode reactance network to correct invalance

or use core coil relation in parraleled harmonics frequencydifferential, that is coil can say initialize at 60CPS but Back CEMPis backfed at 120CPS dobling voltage and dividing time by 2 , but ithas to be pulsed back to battery in a blank interval as the checksumof vector crossing becomes negative if done simultaneous ...

Think in transverter as theoretical computable solution to theproblem.

In reality its kids stuff , only the tuning is the real bitch ,butwith the little circuits being made as to control the variables is

getting easyer to get there ...

OU is getting Visible and tangible , that permits its use ....

THERE is were the real fun starts ^_^ !!! :)))

Hector :)

#11320Re: Fwd: Joe Cell Theory .

I posted here long ago the sonofusion frequency and the 3 phase 3electrode cell & the capactrode system ...

BAD thing Eugene Malove died for it and nobody else cared ..

Maybe JOE cell will reopen the issues ?

Only a bit EXPENSIVE to engage on ..

Hector :)

#11499Resonance collectionHi, I have just uploaded a simple schematic for resonance collectionthat just about anyone can assemble.Only one FET is required and very few components.

Cheers Phil..

#11758

ON BCSRC.JPGDirect Bridging to battery will damage it ...


11/95

Resonance must be impedance matched as per looped RV schematic werebridges (3) are specified in tripleflux mode ....

That is using BALLUNS or TRANSFORMERS tuned to 60 CPS wave specificsin RF mode as to vectorize V/10 = Ix10

Reread LOOPED RV schematic ....

Hector :)

#11991Re: financing old pattents

Hi Larry

What you do for starters is take an off-shelf 7.5hpAC motor andconvert it to ROTOVERTOR mode like Hector has taught about 20 peoplehere on this board already who have actually done it and tested it,then shoot this with pulse DC (both ways)...then you set up a

backemf/recoil diode recovery circuit over the switching thatcollects that huge kickback, put that into DC caps, then knock thosecaps into a 2nd battery stack to charge.Really the chassis that ALF has now, and same one NW managed tosalvaged are lots like a regular forklift motor (coils against coils)and you could also convert a forklift motor to HV operation if yourewind the winds with thin or litz wire....Also a place to go to, is "the fuel-less 300hp" enging advertised foryears in back of popular science magazine - its plans for a GRAYmotor you can make yourself...this is where I got my start about 8yrs ago...they have a website too...The actual GRAY motor design to me is outdated and noteffecient - youneed permanent magnets in the rotation (as stators) to make it golike crazy and you dont need HV...So dont pulse against the magnets, instead have the power input be

going to ignite N-N bucking coils, then the stator magnets arepotsitioned to PULL the rotor coils towards the magnets AFTER the N-Nevent is OFF.When this happens, it REGAUGES the polarity of the rotor coils/cores,so that when the rotor coils/cores APPROACH the next stator coil, itwill not be stuck in N-N bucking mode, (causing clash and wastedrotational energy) but instead will beb ATTRACTIVE (now S-N) and youget a FREE POWER STROKE with no power input.This is what I have been preaching for years, and have made many

prototypes and done shows proving how well this regaugimg of therotor cores works. Most people do not understand it, no matter how

many times I explain.

ciaoK


12/95

#11994Re: Norm's MRA - - - - Off topic - - - -

Hi Steven

A guy in Canada made me one of those Bedini GRAY tubes, right fromthat Keelynet post with all the infor you need, in Bedinishandwritig... I sent it to ALF like I said.THe carbon blocks are going to where out and the lengeth of themwould cause some resisitance... - I have met Lindemann a couple timesonce at KNet conference, and once at Bill Mullers...he is serious guyand good speaker and works with BEdini too...Did you know Bedini usedto work with ED GRAY? Its all one family...Look at BEdinis GErman patent and see the "regauging" magnet INSIDEthe core of his motor....this is what you need to do to any GRAYmotor I preach all the time.

Personally I think the GRAY conversion tubes are not usefull in lowervoltage work,, unreliable at HV work, and dangerous. Their only useis that they dont make diodes that can handle that "radiant" HVenergy...so dont use HV!..so MUCH BETTER to stick the AC legs of aFWBR made of HV didodes across the motor switching, then place DC ofFWBR into caps, and SWITCH with 2nd switch just one of those AC legsand time this to be slightly staggered in time (retarded) as comparedto the motor switching. THis cataches all the backemf, recoil, anddoesnt affect the draw of the motor, and makes the motor run fasterand more powerful, also while filling caps that can charge 2nd

battery stack.THATS IT....everything else "GRAY MOTOR" wise is distraction to me.ciaoK

#12147Re: Tales of Ash

anode cathode

chemical equilibrium electrolite ....

cathode reacts exothermic ...

regenerates endothermicaly with anty - sulphating or anty oxidating

anode

results are an ethernal self charging battery ....

Russians, chineese and japaneese received the formulas ....

( US for its greed was left for last )

( Maybe they can steal AKoil stuff )


13/95


14/95

revise my emails and postings on air engines and water "diesel"engine.

compresion increases temperature 1 degree per each 1/273 gas volumenwere cold air is injected it expands within a compressed medium wereas per thermodynamic law mechanical tensor equal vapor pressure

relative to temperature and pressure density ...

as heat is transformed to mechanical energy a densification occurs ((were OU is)

The only trick is to find correct settings on volumen and pressureat optimal engine speed ( mechanical resonance ) were besttransformation occurs ...

Recompressing the cold air makes the system a closed loop , properairdensity and compresion parameters are needed to properly USE the

AIR DENSITY energy GAIN ( There is energy is COLD region ) as in HOTone) .

That is what 240W solar pannels and RV run air compresor are .....Air hog TOY motors add science to the solution ...

You dont get free energy because you lack information ....

its because you let yourselves deviate from it with any informationthat looks fancy and seductive ( even if its a piece of fucking

bullshit ) ...

go to BASICS , simple, LAB testable info and projects ...

Stop remaking square wheels ....

AMEN !

Hector :)

#12206ZPE on a toy (from the bowells of Stargate Rosswell and NSA dungeGet a lazer tag toy .....

To be exact Tiger electronics Team ops ..

IT is A copy of the Rosswell(ET) tech laser battle system themilitary uses for War games .(not the original UFO 5MJ CW laser ones)the level 5 training units only .

It contains built in MRA - "Reactor" core within the (Circuit)

How to activate ZPE core ....(VTA)


15/95

use only 3 batterys ( 1.2VDC ) each nickel cadmium .... from thenegative pole upto the "halfway" + link .... left half of the

batterys out .... I repeat 3 batterys are not used (dampers)...

Trick is to put in with a slight snap the battery pack in .....

The best part is such pack must be new uncharged one I repeatUNCHARGED one ......

The gun will start a coundown. press trigger it gives a reversecoundown of -ten and becomes ZPE operational ....

then play forever ... as long as you dont detune the gun getting instrong microwaves or damping fields it will operate forever.

The artificial intelligence programmed into the chip will

automaticaly switch to ZPE mode recharging battery into multiplelayer onion quantal barrier charge creating a reactor code modeoperation as intended in the never need a charge ZPE military unitlasers (were original laZer Tag electronic chip was copied from ) .

like I had always said....

Anyway I will win ..... with over 5 million units sold already(try supressing that ) single player lazer tag from tigetelectronics (2004)

Unit also is capable of thermal initiator transform ...

7 units out of ten will work in zpe mode as out of the box using 31.2VDC UNCHARGED ... as from the factory NCd batterys.....

(3 may need tuning or pheaking )

As a note a tuned door BUZzER a diode and Ncd battery will do thesame tuned with a magnet in a positive bias mode with an aparentlyuncharged batt .... the buzzer tension and contact parameters are

critical ... adda piezo ....

It will buzz forever ...

The gun will operate on 4 watts of ZPE , its a public sample wileit last .....

Join with the RV and the ZPE disclosure and its a full disclosurewith a $40 dollar off the shelve military ZPE working unit ...

Enjoy ...

Muhahahahahahahahahahah .... !


16/95

You have no idea what is next ...... (but I do )

Hector :)

HASHAHAHAHEHEHEHEHE !

All that is required is the will to ask for a social and politicalchange ....

get a toy and Nc battery pack ..... or put an RV on TV .....

Supress that !!!

haaaaaHHHHHHHH hahaha! harr harr harr!

as MRA this circuit is verry touchy to tampering and as with anyartificial inteligence linked unit it will resist such tampering and

go on "DEATH" mode)

ZPE requires spiritual development .... thoose having it will haveno problems on initiating the LA (Z) ER TAG unit

(LA) light amplification (Z) ZPE (ER) Electronic Reactor (Tag)(transformer amplification Gain)

do not operate outdoors (Use IR CCTV camera to know why ) you maydissapear into a blackhawk and end in a dark unknown place ....

(somewere ) in this dimension or the next ...

Enjoy!HECTOR! (see all of you later )

#12289Re: throat-seal lube for air motors

--- In [email protected], "Phil" wrote:>

> I will tell you right now, that 10PSI above atmospheric pressure> injected on ONE piston on a V8 motor will break your hand if you try> too stop the crank shaft turning with a wrench.!!!>> Cheers Phil

Its adding a % of extra air (cold) to a hot compressed volumen as tosum kelvin thermal to mechanical expansion and get OU ...

(I already gave the details ) what else people need ....

Its like RV make one TUNE and find out ...


17/95

Hector

#12335Re: [EVGRAY] Re: Rv test part two [RV world record]

10.8watts input to RV at idle is the world record I> beleive...

maybe was but i hold the record at just under 2.8wattsBrian PraterCavetronics , i just cant seem to breaK THAT 23MILLAMPS input..

#12336light bulb

I have my setup going and on my output i have a 60 watt light bulb thelamp has a point-breaker style switch , the type that turns and clicksand make contact then turn and it breaks contact .. now i can get mysystem running and light the bulb and then i can turn the switch "OFF"and the light stays lighted up same bightness... now i have took theswitch apart and looked at it and it works fine .. so what im gettingat is i can light the bulb and then run it on "one" wire and it stillwork ... so the deal about my metters and such ,, now maybe you willstart to understand how this is working ....

But i can not start the light bulb out with just one wire , i have tolight the light 1st then remove the other wire by turnning the switchBrian PraterCavetronics Labs

#12339Re: Rv test part two [RV world record]

Hi Kone I better explain the inverter system that is operating.Inside the inverter is a little 12volt 4AMPH battery that does allthe BEMF collection.

What I have done, and like most of my circuits is use 2 batteries soone gets charged while one is discharging.Now because I have been down the long hard road of 3rd partytesting many times before, I designed this inverter so there is noif or butts of the true current consumption.This being, because the BEMF recharging the main battery gives youweird readings as it is, AC current in and out of the battery.

Ok, the main battery Ash is using is a one way current flow becauseit is totally isolated from the BEMF collection. This is where Ihave used heavy diodes both on the "negative and positive" feeding

the inverter.The shunt is wired before these diodes and is connected directly atthe main battery, so will also give you a one way true current


18/95

reading.The small 4AMPH battery is wired directly too the circuit with themain battery diode fed too this.

Ok, the small battery has been "discharged", and when the mainbattery is connected the circuit will operate. All BEMF is fed only

too the small battery, and as it charges very fast from the BEMF itnow takes over and powers the inverter. The main battery only feedsthe inverter at peak current demands as the small battery has littlecapacity.

Now, I was going too use extremely high capacitor values too replacethe small battery, which I did!!!! But with 16000UF the darn thingswere shooting so high in voltage it was blowing out the FETS. So,this is why I ended up using a little battery that had some bettervoltage regulation.

Ash, hasn't got the current low enough yet running the RV. Why?

This circuit has multi functions that dreams are made of.Ok, firstly he has frequency control where he will find there aresweet spots, where close too 53HTZ the wattage will drop once again.It is a tricky one too lock on, but this is what happens.Secondly the inverter has a secondary frequency. What this does isuses you're dialed in frequency as a carrier wave, and in thisfrequency Ash, can dial in whatever frequency he wishes.So, for example: if the motor is operating on 60HTZ, a turn of adial and he can dial in say 270HTZ riding inside the 60HTZ cycle.

The next thing is the resonance collector. This is in a separatebox, that will now pull out at least 200watts from the RV with noreflection on the main battery or motor, as I designed this too dothe opposite by using the secondary load (lights) as a boost on theRV, where this circuit forces the RV into stronger resonance byutilizing the secondary load resistance.I believe Ash has posted about this circuit before being a ghost onthe RV. The biggest issues we have had though, is it can force theRV too generate a couple thousand volts, and with the limits of theIGBT's being 1200volts, it did fail once before. Hopefully, I havethis better protected now.

All fun and games.

Cheers Phil

#12346Re: light bulb

Like a resistive one line resonant node dipole end ...? o_O ?

yess it can be posible but you need to erase all otherposibility like capacitive line interaction an all sort ofdielectric leaks or other switch artifacts ..... RF acts different


19/95

than normal non-radiant ac power..

Hector:)

#12355Re: News article

This is verry important news as is same as electric rocket enginepatent but using microwaves .....

In shorter frequency rf aether flux thrust is more efficient than atmicrowave level , in RV mode its 1000X more power per squarecentimeter using photonic emmision flux , ( light ) Not microwavesas energy feed ... catch a photon and its light speed sail...

Ever seen thoose light powered bulbs with the rotating gizmosinside ?

Hector :)

#1236410kW RVRe: 10kw RV

You remove the capacitor from the exiter windingtake main 220 winding and place capacitors untill you got a reverseinduction driven LC .....

it will be radiant energy and it will be OU ......

you just need to learn to use this mode of power ...

remember its RF and as RF it can LIGHT BULBS with a single wire !

Search Tesla , wireless power and single wire transmission...

remember also to use RV to reduce drag ( fan design ) bearing and air

friction loss issues ....

Thoose HF gens are cheap and with brushed ones wired to 480VAC you cando power factor correction marvels (OU) ....

As I know thoose generators come also in 3PH 120/240/480 volts ACfrom 10 to 100kw....( Florida gen dealers ) ring brush ones are A!ok for OU power factor correction and motive power..

AMEN ! !

Hector:)


20/95

--- In [email protected], "waterfireho" wrote:>> Hey Hector,>> A while back you mentioned that the Harbor Tools 10kw generator head> was OU Ready....

> Do you have anymore info you could share about what Mods need doneto> make this happen?>> send me PM or Email if you want.>

#12368Re: Have you seen this?

Any generator (brush) type can be converted to a gray motor and be

ARC gap commutator controlled to get RF radiant energy effectWhy you need this?.. ANY motor or generator can be made RV typemotor-generator electric turbine using also ZPE radiant energymodes.? Its seem there is this tendency to mirre in obsolesenseinstead of goin next step ....

Go simple go cost effective ...

Use what is at hand ....(ZPE is there waiting to be seduced)

Just remember most of the statements i have posted in the last 7years had being validated and with inrefutable lab proff ...

Thoose Harbor freight generators can be made into gray motors

add a ring brush to the rotor (EM) and play with the ac andpulsemode combinations (limit it to 4,000 RPM and you are OK )

No need for a $10 million proto when you can built a full ZPE labunder $10K ... ( the cost of a newman motor) using off the shelvestuff .... ( anyone can make an RV ) I think with the same mindset

anyone can built a Gray motor Or I may say use same principle in amore efficient cost effective platform...

The experience konehead had aquired with the pulsemotors is fullyaplicable to this cheap already made generators ... try the voltageimpedance combinations in semy resonant modes using CEMF recoverymethods. 3ph generators are more effective (120 deg) pole angleresulting in a more effective 90 deg pole pull-push magnetic forcevectors ...

Power slavers (debunk that)! how it was? a 30KW generator runing at

RV /Gray mode using under 8 amps ? )most of the preliminary testinghas being done here already on what is needed to get this things torun..(easy)


21/95

HEHEHE !

Hector :)

#12393

Tesla- Gray- JOE CELLRe: [EVGRAY] Re: Tesla- Gray- JOE CELL

Steve,I am afraid you may have misunderstood that writeup. Gray's switching tube is equated to the J-Cellnot the diode. The schottky diode is the element that ensures that the pulses are unidirectional. Thediode is replacing the unidirectional vacuum tube outside of the switching tube.Also, please note that the design I presented is a design using modern components with the samefunctionality instead of the old no-longer-available ones that they used before. These modern

components achieve the same thing as Tesla was achieving with his high voltage DC discharges.Please experimment on that design and it could blow your expectations for free energy away. Youwill have far more than you expected to discover by way of free energy secrets.Happy experimenting!Baraka.

#12405Re: Tesla- Gray- JOE CELL

Hi all

When I was making konehead-motors (N-N coil pulse motorswith "regauging" magnets added after N-N coil event) I also did lotsof experiments with SPLATTER coils - I got around 50 pre-wound coilswith very super thin winds that make almost 20VAC (shown on nmeter)each, when holding them next to a motor's stator coils - I found bestspots are at 90 degrees to face of stator coil...

Anyways with around 20 of thesee positioned around a running konheadmotor, I could get up to 1000VAC on meter, on scope, around 2000VACspikes if not more than that - in fact I could light up smallflourescents with lots of these in series - - ANYWAYS on subject ofGRAY tube, what I discovered is that by holding the output wire ofthe platter coils about a few millimeters away from the positive ofthe run battery, I could get a good zap of a spark to jump from thelead wire to the positive of the battery, making the volts of the

battery flutter up - AND then playing with an air gap on the splattercoils themselves, (not now zapping a battery) I found that lookingwith a scope, that HV AC signal the splatter coils makes can be

changed to all-DC pulses, (!!) just by the distance of that gap - toomuch, or too small a gap and it wont work - that gap has to be

precise and locked in, and then the AIR works like a diode - the


22/95

juice has just enough power to jump across the airgap, but then onceit does this, it now doesnt have enough to jump back - ipsofatso anair-diode. SO what I am getting at, is that this is what I beleive aGRAY tube does in "essence" - the airgap is adjustable, and once youfind the perfect distance, it starts to change the AC signal (actuallDC with negative spikes) into all-DC, and the DC now fills caps to do

work....along with this, you have removed the destructive transients, so yourswithcing will last. I think a "better" GRAY tube could be made, bysubstituting 90 degree splatter coils (mine had thin iron cores) forthe grid myself...another thing to try..Also the other point I am trying to make is that Tesla didnt havediodes, so to make his diode-like systems work (changing AC to DC inorder to fill DC caps) he used high voltage and air-gaps to make hissparks jump across air is what I think......ciaoK

#12414Well this is what, in effect, you want to achieve. You were getting high voltage discharges to jumpacross a spark gap to the the positive of the battery. You can also achieve the same thing using adischarging capacitor.If you want the juice to continue to have enough power, use a diode to eliminate any negative(opposite) impulses. It is the negative( or opposite) impulses that kill the energy attraction. Try yourexperiment again with a diode connected to the postive electrode of the battery.Also, in case you may wish to see how a spark gap influences the energy content in a capacitor orinductor, check out this site:http://www.intalek.com/Index/Projects/SparkGapExp/SparkGapExp.htm

Happy experimenting!Baraka.

#12475Re: X4 Group Problem

If you take IR frequency RF as HEAT and create LC resonant to HEATthe AC electron spin signal transfers to radiant signal one , letssay like in WATER at 2.450GHZ a resonant LC becomes a cooler ofambient heat in that RF range and frequency At hi Q MRA mode LCfeeds on heat .

A transverter at ambient heat frequency its resonance beingendothermic produces molecular superconductivity and cold energywere R in a perfec theoretical environment = 0 (Zero point energy)

I was the first to POST that overunity is due to transformationYEARS ago and is well proven in stochastic resonance labexperiments ...


23/95

In nanometric scale creating HEAT frequency RF sinks are way totransform ambient energy to usefull energy ..

I posted this YEARS ago , a few bastards taking to patent the ideawithout even understanding the basics ( many got gready and got

killed ...

Good! it serves them right!

Goin to basic repetition of main disclosure , ambient HEAT as RFenergy source can mantain a nanometric MRA working forever ...

#12476In a perfect LC (atom)particle G (gravity) flows toward centerof particle were C light as spherical waviton takes energy fromQuantal fabric (space time tensor) thru aether flow in spiral toward

center Were Mass M = equals C divided by the square root of time ...

Mater is nothing more than modes of light in spherical standing wavefeeding from time space tensor differential as G force.

as gravity increases time accelerates as gravity decreases timeslows down ...

At 0 G on earth surface time equals 0 mater Mass = C entering 4rthdimensional state as hypercube transform ...

(Red shift is a gravity illusion ) black holes are transformationengines (The mother of creation resides inside them ) .

Hawkings and Saffati are 2 freaking assholes.....

closing the loop ? do only thermal , forget the electric ...

The planet is catching fire already and the ETs will feast on themashmellows ( your freaking burning in hell souls if you dont speedup the freeenergy use and disclosure )

Got money ? Grants ? Donations ?Do something!

Its late and overdue

Hector (:b

#12592Re: brush commutator help

Goin back to basics .


24/95

A short at coil ends equals infinite capacity were inductance willcharge at maximal amperage with a 0 volt potential .

(Current node )

As short is opened at max potential that potential

releases energy from its current node transfering it to a VOLTAGEpotential within a capacitor Volts with a farad potential that canbe quantified as JOULE-watt within an AC system .

(Voltage node )

In AC transverter setup or RMA or VTA or EMA4 the same simpleequation of RF aplies as Radiant energy does not differ any from RF(radio frequency )

Wire mass must be equal in primary & secundary to valance the

endothermal equation H=IrT .

Turn determine impedance , Impedance determines Q within a given setof parameters , can be broadband as UNLOADED RV and narrowbanded asLOADED RV in Tuned conditions .

LOADING is an Impedance determining factor ...

T (time ) Frequency F Pulselenght well managed = ZPE OU

Hector

#12617Re: Deliverance RV resonance v1.1 uploaded

--- In [email protected], "davidkou" wrote:

> The charge battery gets charged very quickly, around 0.1V/minuteor

> more. NO INCREASED LOAD at all visible on the inverter, seems tobe charging for free.

That is the ZERO point capture .... and the non reflectiveextraction circuit (were enery at 2x2 stage is defined as joulessecond )

>> Some points and observations;>

> 1. The TIC126D Thyristors I had were all bad. I changed to 2N6509and bingo.


25/95

part selection sometimes is critical ( internal resistance andswitching time being main issues)along with amplification gain.>> 2. I put in some current limiting resistors in the darlingtondrive to the thyristors. (dampers)

>> 3. I noticed that the voltage waveform across the Run Cap is 60> degree lagging the input waveform to the RV (not 90 degrees as I> thought).

120/2 = 60< 3 phases are 120 degrees one from the other relative toline in a phaseconverter is 120/2 . Relative to primemoveralternator lags 30 deg max . (critical )>> 4. Battery carries on charging on its own for a while afterwards.> Radiant energy charging like Bedini motor.

Radiant energy = RESONANCE = RF (radio frequency ...)>> 5. My previous test of Kone's FWBR across Run Cap was probably crap> because of the dodgy TIC126D thyristors. I will re do thisexperiment> soon.>> 6. A thyristor tester is useful bit of gear.

A solid state device analizer is also usefull

Congratulations ....

Remember in stepdown from hi voltage say 236 VAC in a RV alternatorsay 8 amps circulation .. 236/10 = (23.6 vac at 80Amps !)

wire mass must be identical in primary and secundary impedancematching ballun transformer or FR trafo 10 to one ratio must be aturn to circular mill ratio 10:1 within same weight ratio 1:1

OU is OU ZPE is ZPE and denial is no longer possible with thepredicted eventual looping of this systems ....

The schematic at don,s page being "understood" within standardtechnology ... being RV as sample 20 amps max at inverter input200Vac 5 amps at alternator and split into a pulsed diode 3x3 plugand 3 dual split 2x2 extracting capacitors were joule time energyJ/2 may equal 20VDC at 25 amp potential versus the 20 amp 12.7 maxinput expenditure fed back is a predictable 1.618 overunity as

predicted in theory or 1.33 as tested in VTA in real lab testing(real world in vitro test)as is same universal principle .

Remember RV was first to show ratios of 1 to 12 (Cop 12) in virtualenergy (radiant energy ) over 1KW potential with off the shelve


26/95

stuff. can easy go 10 t0 30KW increasing frequency (with care not tooverrev destroying it)

The way the information was put out was to force people to learneach step of the experiments as to make posible to open eyes to theKNOWLEDGE the whole represents .

RV belongs to all of you .. looping it, is almost there.

and I cant be more happy about it ! :)

Hector :)

#12654Re: Kone... Thanks man.

For PM setups or EM synchronous you can go to 1MW (Tested) along you

can play with the impedance and dragg issues

10 hp is OK for 50cps as the higher mass ratio compensates forfrequency (lower).. 580VAC motors are OK >

Hector

#12723Re: Help finding resonant freq. of a coil

Grid dip meter and a frequency counter (RF)

digital Audio frequency generator and ac to dc bridge series shuntedto LC you are tes

ting.. (Extreme low RF) ac

Hector

#12764Re: RV muller zero point switching

Is the hyperwave signal , a wave upon the resonant wave and itdances inward toward resonance and out of it ...

is common to looped systems as battery goes out of OU overchargedthen discharges and goes into OU as it charges & discharges incycles.

As is common to uneven pole generators , you get TOTAL frequency

modulated by a sine integral or compound hyperwave result of thedifferential within the charge potential of all separate wavesforming a wave of a lower frequency .. (Ema 4 stepped discharges,


27/95

Newman plasma discharges , teslacoil hi frequency stepped streamdischarges , natural lightning volt as some more complex samples .

Hector

#12795

Re: car engine converted to neo magnet pistons

There is info on Coaxial ring solenoid that may be usefull for thisproject, old audio speaker metal caps and hi silica sch 80electrical pipe machined in concentric rings with concentric serieswindings that slide in concentric mu metal passive poles attachedon cylinders like squared dovetail ends , or collapsible telescopealike .. slide into each other ring to ring on close tolerance gaps.

pull is x10 times ordinary solenoid pull ... & requires no magnets

There was a company named Solenoid Corp was blown up by petrol eliteas they ran a motor bike all day with a D size 1.5vdc flash light

battery, inventor was murdered.

I got all the data using stargate window, and avove statements oncoaxial pipes within pipes with magnet wire series winding is itssimple secret.

The poor devil was better off giving the dam thing open source .

A nation that kills its inventors commits suicide ....

If terrorists dont make their inventors blow themselves upi think is recomendable we start practice muslim prayers and readingKumran ... ( They will win ) as AMERICA Kills and fucks their owninventors ...

Here is some coil solenoid candy ...

http://www.smeter.net/feeding/selfres3.php

Do a search ..

http://search.msn.com/results.aspx?srch=105&FORM=AS5&q=coaxial+solenoid

Amen!Hector :)

#12799

Re: car engine converted to neo magnet pistons

If cores are coaxial-multy tubular the pull force will be multiplied a


28/95

hundred fold, Pull area force relative to Gaus per square centimeterin circular sleeves.

Hector

#12808

RE: [EVGRAY] Re: updated Compilation on one wire light bulb

My one wire bulb works like this...Magnetic reconnection is the process whereby magneticfield lines from different magnetic domains arespliced to one another, changing the overall topologyof a magnetic field. It is a violation of anapproximate conservation law in plasma physics, andcan concentrate mechanical or magnetic energy in bothspace and time. Solar flares, the largest explosionsin the solar system, are caused by reconnection of

large systems of magnetic flux on the Sun, releasingin minutes energy that is stored in the magnetic fieldover a period of weeks to years. Magnetic reconnectionin Earth's magnetosphere is responsible for theaurora, and it is important to the science ofcontrolled nuclear fusion because it is one mechanism

preventing magnetic confinement of the fusion fuel.

In an electrically conductive fluid or plasma,magnetic field lines are grouped into 'domains' -

bundles of field lines that connect from a particularplace to another particular place, and that aretopologically distinct from other field lines nearby.This topology is approximately preserved even when themagnetic field itself is strongly distorted by the

presence of variable currents or motion of magneticsources, because effects that might otherwise changethe magnetic topology instead induce eddy currents inthe plasma; the eddy currents have the effect ofcanceling out the topological change.

http://farside.ph.utexas.edu/teaching/em/lectures/node84.htmlCavetronics Labs R&DBrian Prater

#12812Re: updated Compilation on one wire light bulb

Node-anty-node werever you are at it you get it with one wire.

(KEEp it simple my friend )

Hector


29/95

#12818Re: updated Compilation

The nodes are points of concentration of electrons and vaccum ofelectrons, they can be made as resonant on multy harmonics along a

conductor alike the light bright and dark spots that form along 8 FTlong FL tubes ..

Like in Jinis setup , first is attain resonance then lower thecircuit power or open the series circuit to attain linear open loopone , if one attains magnetonuclear resonance from the ambient heatyou can get looped OU from a resonating kitchen sink !

resonate the electron field you can get permanent wireless fixtures.Get shuman resonance as a sample resonate to it , then feed on oneof the 1.3 to 1.8 mhz ELECTRON harmonics within the shuman

HYPERWAVE .... you get all the free energy you want ...

like resonating ELECTRONS in a lightbulb filament within an OPENdipole, ideal will be to place other open bulbs with independentswitches and close and open each independently to see if they remainatomically resonant within the RV LC influence ....

If they do, you got something bigger goin than you may think ..

pure electron resonance of the filament with a low frequency exiterradiant energy field ....( Like wett finger stroking a grass cup andgenerating untrasonic waves, RV rf AC EXITES bulb atoms to oscilateat higer frequency in open resonat dipole emmiting heat and lightin the prosscess... at a higher frequency...

That lab test may finish iron out the issue that RV truly generatesradiant energy and that Newman, Bearden and Bedini were wrong in theanalisys of its nature .

Tesla neither grasped the true scope or did not have the tools todisclose such knowledge due to the limited scientific understanding

at the time ..

Hector

#12821Re: OU App

Take on account Time , phase relation & phasor .. WITHIN FOLLOWINGFORMULAS .

(((v1+V2+V3/3) X (I1+I2+I3/3)) x 1.732)X PF = WATTS (CIRCULATION 3PH)

A,B,C PHASES


30/95

WERE ac INPUT 1 PH IS (V X I)X PF = watts

(System as is, Is OU )

PHASORS A=0 (LINE) B=120 C = 240 WERE A=0=360 (VIRTUAL RELATIVE)

SO B MUST LEAD A BY 120DEG WERE RELATIVE SELF INDUCTION SETS B ANDC 120 240 DEG APART BY MEANS OF THE CAPACITOR THAT PROVIDES THELEADING var POWER TO THE ROTARY 3 PH ENGINE Vars runs the EMAeffect . the 3PH polar field is rotary triangle EGG shape. wererelative max torque to ROTOR 2 poles is at 90deg angle (relative).

The Rest is Resonance and its transformation engine potential usingthe ZPE on this ENGINE TYPE > nodes < .

More clear I cant be .... (Its so dammed simple ) . and as before

this formulas must go into the compilation.

Including RF resonant ones (aplicable to jinis work ) "Q"

else the simple structure is lost.

Quote*********maybe im wrong but ? maybe im right also ?*********I may Say , partialy on the right path (Important One)

HEHEHE! (The Lab Models give the answers!)

Later you can justify by BOOK law....

But the RV theory postulate Remains Fixed ..."OU (Overunity) is the result of transformation and the dream ofhaving free energy from ZPE or other means relies in the dominion ofsuch art to state of perfection..."

The Tools were given to all of you .. (Use them well) use them tolearn ...

Hector :)

#12822Re: updated Compilation

Relative to schematic ,


31/95

werever you resonate the linear nodes there is a NEW aspectof amperage you must know ..

mass or ampere load were amperage in unit of mass = concentration ofelectrons per square centimeter of unit mass that equals a virtual

linear impedance to the linear flow of RF signal as A VECTOR signalacross a medium (mass ) "conductor" R lightbulb is the cross nodewere as LAW of resonance Voltage must be 0 but within the cuttoffregion of MAX current (Standing Wave) (search RF antenna dipoleelectrical propertys) .

This current is capacitive in nature and has NO voltage component.It is an ELECRON DENSITY linear wave .

"Elektron" with K defines it, as a PART of RF Radiant energycomponents.

WERE R takes the LOAD and flux increases speed the energy is releasedas HEAT due to the lesser mass junction (filament) that restricts theelectron waviton flow .

So free wire end is REVELANT to tuning a radiant one lightbulb system

See also Tesla single wire energy transmission (Colorado lab notes).

All this Applies...

How many Miles he lit a lightbulb away ? 600 hundred ? OPPS ! and inthe PROPER NATURAL frequency standing wave the lightbulb lit

perpetualy ! so his transmitter was USELESS ! Not nessesary to getFREE power from the "medium" ( he ran his car on it).

But took the secret to the grave ....(not me!)

I gave it away (And I am getting screwd for doing it)like they erased Tesla they will try to erase me ..

Not if people fight for this and keep it free domain.......

So From My grave (if I ever die) I will raise my middle fingerat the power elite world .

Wile people will built ELF wave Radios detecting and taping the ZPEnatural energy fields .

Hector :)

#12844Re: coils on neo piston engine block photos


32/95

Well I got an Idea ...

Use RV to run air compressor make the car an AIR car using theexpired Leeroy Rogers patent ...

RV can run all day & night with a 12V battery and 2 120W solar cells

on the car rooftop ..

Use 12V air solenoid valves to suplant spark plugs ! as in patent !

Hector

#12851Re: teflon main bearing inserts for cars

--- In [email protected], "Mike" wrote:>

air motor first.. go rogers.. build heat exchanger "pipe in a pipe"..> use second tank once to pre-cool exchanger.. so injected air is cold> send cold exhaust back to compressor..

Ok

use rest of cold exhaust to cool injected air.. (ERROR )

NO its HEAT the injector and the AIR being injected into cilinder

heat also the main reserve tank to increase ENERGY vapor pressure

(GET the freaking free energy )

the cold exaust goes to compresor pre-chamber ( a cryogenicalyisolated small tank .. all this pipes must be heat isolated as not toloose the cold air molecular density .

The COMPRESSOR Inlet and HEAD is what you need cold so you get thelowest vapor pressure on hi molecular density to get the temperature

to volumen gain in compression as to attain a self substaining system( the OU energy comes in as air gains vapor pressure from the ambienttemperature ... main reserve tank and lines .... (non isolated ) solarheated if posible ..

Sinse Leroy patent Is expired and is free domain is usefull todisclose its trade secret (thermodynamic conversion) relate to OLD

postings on this issues were I mention that air expands or contracts1/273 its volumen per deg centigrade , using this law and creating

proper exchange mechanics (AS Leroy air motor ) unlimited energy canbe extracted from the ambient , seek old postings on absorbatron, suck-

a-matron ( I am still wondering if the people from ak-oil finalylearned to suck!) but definitively their silense sucks more than anythermodynamic device !


33/95

Keep the freaking notes ! the patent leaches are here ! watching!

avoid free domain stuff patenting! ( Copy keep copyright & pass on )

> and might not need to get to 3-400 psi.. depends on displacement..

> i got this 22.5cc trimmer motor runnin like a champ on 50 psi..> those $7 refrigeration valves from surplus center work great..> they are fast, good upto 500 psi, and have a high flow rate..

air hogs toys are big help in understanding part of the stuff !

the rest comes with lab ingenuity and practice ( plus a bit of posthelp)

Hector

#12891Re: big neo magnet rotor on car motor

A mental Picture of an alternative Path :

GET!One of thoose big 15 or 20HP motors ...(aluminum) Junkjard cheap!

if one side has a C plate (Waterpump end face) adapt a transmisioncoupling (standard) and use a MOTOR crackshaft to pressureplateadapter in tip of motor shaft ...

USE as IS Using 3PH FREQUENCY DRIVE , frequency ,pulselenght andamplitude regulated . 12V batterys and 250W of solar cellsfor afreaking demo .. ( Raivo was Working on computer controled frequencydrives )

I just hope you had put some of the grant money for tools ...as a lathe & mill is needed for some parts ..

Remember hi frequency equals more HP at hi speed to low speed ratioin transmision gears to differential tire HP torque output &finalspeed. a 3HP motor at 15RPM can deliver 11 tons of force.

a 20 HP motor with rotor shaved for hi speed , like a conservative73 tons of force ..

that is 146,000 pounds of push force ...

Beats an airforce F16 in acceleration when you let the clutch loose!

A 20KW fuel cell a 20KW adaptive frequency drive with the avovedescripted methods (IT BEATS an F16)


34/95

Hector :)

#12916Re: Please let me know what you guys think

After being Shot at , Darted with Neurotoxin , poisoned with

listeria neurotoxin,salmonela, stricnine , having the car smashedhaving every chance uf making money rug pulled from under my feet .

I have a SAY about conspiracy ...

Built RV and try to show it on national TV ....(I dare You)

It is preferable to WASTE 90% of a motor power when you can save it?And use it at demand ...

(The Worst Conspiracy is the conspiracy theory itself )

(It is a true cover for murder)

Ask Mallove ! He knows ! (Use channeling )_

Ask MYTHBUSTERS and Discovery Science the freaking EXCUSE to DENY RVfrom their TV shows ..ASK GREENPEACE DENIAL (Worst ONE) as group isanother ELITE scam ! "people control agenda"

Hector :)

#12980On Motor electric bits and kicks !A 7.5 HP motor at 1725RPM its 7.5HP

at 17,250 RPM its 75 HP (sameweight )

at 172,500RPM its 750HP (Sameweight )

Optimized as electric turbine its WEIGHTcutt of to 1/3 its original weight .

That is from 65 pound aluminum frame 184TCH baldor to 12pound one

its 750 HP on a 12 pound package ....

So EASY to do with the right R&D money .....

#13012Re: An Inconvenient Truth - Good movie/docu

OK answers shoved within written text .... (Eyes open )


35/95

--- In [email protected], kenn johnsen wrote:>> That could be, NASA doped the sun with Lithium ? it most have beena hell of a lot of Lithium.

Like floride atoms to EARTH OZONE layer so is lithium to sun

conductivity ...

a few miligrams of lithiun inside an hydrogen bomb you get a superEMP weapon that can erase all US electronics if detonated over 250miles sky up in low orbit over US continent 3600miles radius .

doping a substance can alter its whole even at trillion partspercentage ... and the sun was torpedoed several times with tonnageof the stuff .... with the wrong idea to increase the magneticconductivity and see the effects in the corona ....

effects were 20X and 100x class megaflares , adding that the sun ison its million year pole reversal ( also goin quadrapole manasic )That quite toasted the sun life cycle to half its predicted billionyears life shifting to a green white UV spectra .

IT sometimes takes a compound to exert a catalitic chain effect thatcan alter mayor system mechanics ... like the self replicating

polymers killing all life in the gulf from texas to Florida ..They may end turning the sea into a big jellow alike big pile ofdead man blood alike goo .

Like the self repairing polymeric compounds in some paints thatmutated into prions turning cows and wild mamalians into crazed

beings that eaten by humans infect them with prions also ...

#13110ON be your own power bullshitter ! (DOC)Check picture #2 teslacoil must discharge capacitor series to

primary of tesla coil across spark gap not parrallel as shown there ..also I posted that data first ,with the right way to do it ..

First Raivo compilation included that data ...

TESLACOIL IS source power LC HV resonant then capacitor gap dischargein series to primary of teslacoil were wire mass of primary equalswire mass of secundary ....

After I show the cat balls everryone claims the cat is male and thatthey grabbed the Cat penis firsthand (to prove it is male).

Too late I already posted the 5fth cat leg aplications .

I was first to disclose TESLACOIL was OU and SAME phenomena isREPLICATED in RV as to use LOW VOLTAGE for PRACTICAL R&D aplications


36/95

Avoid dissinformation , even if it looks and feels like the realthing .

If you cant REPLICATE and validate post as such untill provenotherwise ...

Dont fall for things that try to dilute my disclosures on things thatwere NEVER published before RV or TRANSVERTER WERE disclosed .

I was FIRST to DISCLOSE so I cant I will not Give a SHIT credit toANYONE claiming to have made prior publication and more if SUCH

publication is defective and full of USELESS bullshit intended onDISTORTING the information to make experimentaation USELLES in labaplication.

AMEN !

#13359Re: Toroid

Hi Peter and All.Ok, the pressure is on for some coil tricks. LOL.

This link below will show you the most powerful and efficienttoroidal coil in existence.

http://www.rense.com/RodinAerodynamics.htm

STUDY hard on this formula and learn the secret too the code. Checkout the efficiencies of this coil also. WOW.

Ok, if we were too wind a typical coil, and have a center core toostrengthen the field at each end,,, when the coil is energized andlets say end "B" is a North pole,,, the "outer circumference" of thecoil at the "same end" is a South pole.

This is an opposite polarity and equal at the "A" end of the coil.

YOU HAVE 4 POLES....

So while everyone is pulsing coils thinking they just have a Northpole at one end of the coil they have wasted half the potential.

What we do is put a sleeve, or better still wind soft wire around thefinished coil, and strengthen the outer field potential.There are a hundred ways too use this,,, but lets say if we are

pulsing a piston type configuration, we use a magnet of one polarity

in the center too interact with the center core, and around this aring magnet of the opposite polarity, too interact with the outer ofthe coil.


37/95

When our coil is pulsed we have twice the force,,, but much more ontop of this.The reason for this added magnetic potential, is because both polesat each end have been strengthened, where normally the outer of thecoil begins too scatter this somewhat, and cause less of an effect on

the center core.

This is why some people place scatter coils around, but don't realizethey have missed the key here, and have no clue what is really goingon.

Windings?In any circuit where there is some resistance, the center of thisresistance is the collision zone, but I refer too this as the hotspot.This is where any fuse will blow, or a light bulb is the brightest,

or where your long extension lead gets hot.This is the hot spot you want balanced in your coil center windings.This means an odd number of layers normally,,, but can depend onwhere this shifts too as the layers become greater in diameter.

What I normally do is wind a coil that is required, then un-windthis and find the exact center of the wire length.Then mark this center spot and wind again. If the marking is near oneend of the coil, take off some turns that would equal half way alongthe coil length.It is practical too do this and measure the actual full length ofwire if making a number of coils.

Now, you have a powerful coil that is balanced, and you have apowerful center core and a powerful outer sleeve.

Drive with both ends of the coil now, and look out for some realefficient forces you may not have experienced before.

Cheers Phil......

#13362Re: EMA compilation?

A compilation of compilations must be made that include postedcompilations & compilated compilations past & present .

AS per descripted ...

THE RV OU power as translated from HI voltage lets say 200 Volts 5amps translates to 20 V 50 amps (1000W).

If your input translates from 120V .8 amp then at DC inverterside it translates to 12VDC at 10A (120W ) dont tell me you cant


38/95

diode vector the 20V 50 amp using impedance matching to the batteryside?, the only problem you may encounter is the detuning due to thevaractor tuning effect battery voltage introduces in the impedancematching circuit, nothing that cannot be solved using RF tec aproach(Phil can help on that) I think he looped the thing already.

Is up to him to come fordward ( as others that had loop )but keepquiet .

RV LC can go PM low voltage hi amperage resonance LIke in pastpostings statements turning things off to turn them on ,shortingcoils to create pure resonant ampere nodes (Infinite capacitance )(for idiots a plain short circuit does ) as circuit opens it dumpsits discharge as a JOULE potential in a capacitor (remains thereuntil used )

(Dont tell me that shit is not explained here in a hundred postings

or more in a hundred ways " but same sense ")

AS i will not believe it ....(search & read )

Capacitance also is INCREASED as VOLTAGE is REDUCED ,coil turnsreduced proportional to same conductor mass (TESLA books state thesame ) in impedance matchers & transformer building .

Rewire RV alternator to 24VAC ? resonate at super Q state ?

250A Litz wire ? MMM Does NORMAN WOOTAN still haves thoose 25Valternators ? mentioned in old postings ....

Teasing! TEASING ! ~_~ !

Sealed hydrogen filled RV have 10 times less friction ....(OLD postdata ) & cool better as hydrogen takes heat out better than air alonedoes..

You Guys have more data here posted than at any Tesla book ever

written , its a pitty you havent "compiled" the puzzle yet .

(Like in old postings) it may require a MENTAL enema and a braincompilation first .

Sorry if I appear rude (ITS the "GOLD" rush effect )

"You aint got a dammest of an idea of what you have here"

Nor what you may have already have lost ....

C.S [Hector]

#13553


39/95

Re: CS... Esa... (M2513T axle diameter???)

Hector made reference to varactor tuning, VCOs Voltage controledoscillators, amplitude (that is voltage) determines an impedancerelation of a signal on a given impedance value of a resonant

load "LC".

Voltage then vecomes a VARIABLE parameter in TUNING , there is weremost scientists had fail in ZPE R&D as they work on FIXED parameterswile lab experience shows all variables within a ZPE system must beadjustable parameters in order to REACH predetermined constantsneeded to aquire OVERUNITY transformation.

Check Varactor tuning theory (RF) VCOs & others.

Hector was and still Is right ....

C.S.

#13559Re: Another media pie in the face .......

As of what is known in inner circles:

GM holdings looped RV , Caltec Looped RV , DARPA asembled and loopedRV, NASA tested & looped RV .

They cant hold secret that ZPE is related to RADIANT energy and RF(RADIO FREQUENCY) . (now public disclosure )

Stochastic resonance first prof of overunity transform engine.were ambient noise in a crystal matrix amplifies a weak signaltraveling across it. (Other systems also aply) looped stochasticresonators are on NASA top secret equipment stock ! Used in gravitywave detectors, sub-space communications R&D & other uses .

http://mathworld.wolfram.com/StochasticResonance.html

http://www.ecogito.net/projects/download/Stochastic_resonance.pdf

Hector first referal was the Navy R&D in radio frequency filters weresuch phenomena manifested as a transformation of crystal Thermalnoise into signal electrical amplification.

ALL NAVY data WAS REMOVED from the internet after Hector published itas PROFF of and justification of some OVERUNITY mechanics inelectrical circuits .

But all sources cant be silenced and they can lend their revelations

http://www.iop.org/EJ/abstract/0256-307X/20/2/309/


40/95

Input signal + ambient noise (thermal or electron spin )= OU output

Were ((PI+SRA)=PO)/PI= Overunity FACT NO BULLSHIT no disinfo OUoverunity is TRANSFORMATION of energy as HECTOR stated from thestart .( PI = (power in)+ SRA (Stochastic resonance amplification)

= PO = (Power Output) )/PI = overunity

More revelations :

http://citeseer.ist.psu.edu/context/388295/0

Copy the info as the feudal lords "agents" will start erasing thedata given here.

http://www.rasertech.com/tech_overview.html

A Mormon atempt at taking advantage of rotoverter technology"Symetron" (SIMILAR but not equal ) but anyway you name it is RV ina "distorted" form .

Plain RV theft

http://www.geocities.com/robertjackson58/robspatents.html-----------------Another public intelectual property theft & desacreditation !

http://www.phact.org/e/z/JackCarey-sept.htm

Jack Carey, jcarey9622@... 810-618-9234 claims that

Wayne Cochran***********(Mormon) ? aquired Hectors technology in 1982-1987 R&D period ?died of cancer ? due to UV RF exposure using RESONANT florescentTubes ? (ZEUS)?

(A lot to investigate and & confirm or deny)

Invented a? Rotary Transformer Phase Converter that converts singlephase power to three phase and will power 5 HP motor? on aircompressor while using only 400 watts input. Claims? that 110 VAC 9amps input power to RTPC powers 5 HP? motor on air compressor, 2.5 HPmotor on drill press and? arc welder set for 100 amps all at fullload.

Sounds familiar ? (interesting)the conspiracy "facts" go on .

Nothing in the PATENT office existed similar to RV before its publicdisclosure .


41/95

Over 230 different claims to it had apeared in the last 8 years andkeep on growing.

Many from Goverment and academia circles that include doccumentfalsification and the predating of such doccuments to apear prior to

public disclosure .

That is why it is such urgency to make RV a full public disclosureand end its apropiation & technological distorsion.

C.S

#13583Re: Earths diameter being watched?

GPS (global positioning satellite ) and to within millionth of aninch 1/4 wavelenght light laser interferometer .

the planet is sweling but from internal HEATING as orbital plane ischanging due to Human gyroscopic vector force contamination.

(collective Force exerted by machines rotary gyroscope effect)

Worst shit than global warming and I am first to publish thisWARNING! so keep this post notarized.

That is why i recomend RV and all machines shaft rotation be west toeast with shaft ends north south orientation...to mitigate counter-earth movement vector forces .

FACT earth is OUT of orbit and will collide with mars.... (somewerein near future) so who cares about earth getting a last minuteswelling and hard on !

LOL!

Hector :)

#13584Re: another overunity com post by fred

--- In [email protected], "koneheadx" wrote:

> I have a 1/3hp AC motor working as a lawnmower right now, but ifyou> take off the blade and let it run off the "perfect" UF size run cap> (17uf in this case) the motor accelerates and accelerates way past

> its normal "idle" AC sine wave rpm and as it accelerates, the draw> in amps goes DOWN lower and lower.


42/95

This is incremental harmonics acceleration were the Squirrel cagegets reversed fiel rotation as acts as auto transformer magneticamplifier accelerating incremenraly as it reverses power into gridand is fed by the power factor correction itself .

An unusual condition that in looping leads to uncontrolled

destructive acceleration , in hi Q Modes as motor passes a limit& coil and capacitors go to hyper Q modes motor does not turn off atdisconect resulting totaly destroyed by overacceleration centrifugalforce , 30,000 t0 560,000 RPM can be reach in a few secondsdestroying unit .

I warned about this anomaly (Now confirmed in the lab by others)

...you have to pull the plug at> the house power socket of the motor, or eventually it will> explode...Phil got one to blow - he tried to stop the accelerating> by jamming in some more run caps, and boom.> This is more evidence of OU operation in "resonance" mode in RV...> just needs to be controlled.

Looping have its dangers as system can feed off negative time flowcreating time space anomaly (verified by china scientist without

proper safety measures some years back) "dissaster struck"

> Whether anyone else has or hasnt repeated NormsW way-succesful PMI> servo motor as generator tests is not impoertant - those tests are> real, and overunity too by good margin...and have been on the net> for years and he just doesnt want to believe it.

> Best thing to say to critics who insist OU is not possible, because> it hasnt been proven to them, is YOU prove it to me that it is not> possible and throw ball in their court. They cant prove it, so

> everything they say comes back "three times the pain" (JimiHendrix -> machinegun - 1970)>> ciaoK

That is why i say (dont believe ) do the lab do the math !& read Seike Book on Ultrarelativity , what he THEORIZEDI had aplied to motors in vitro years in advance , some of hisformulas err a bit (on aether tensor aspects but the RF theorycomplements what he missed and fixes what he got wrong ...

Anyway he is a fu*ng japaneese Genius! deserves a Novel prize!

(tip) JINIS experiments complete what seike missed ! solid state


43/95

looping of self inductors is real , to that add MRA papers !

DARN! you already got it all )

(You got it all already )it is public .... but aparently it will takemore to notice than when the first airplane was made (difference is I

open sourced all of it ) no patents .

Other issue is my brain was not open sourced so it will take a littleeffort on part of the researcher to understand the scope of the giventhings ... (NO problem if they do the LAB experiments that are public)and bend the book rules to favor OVERUNITY energy transformation as areal phenomena and work enhancing it not against its >RADIANT RF

NATURE


44/95

That is the whole idea to have the voltage and freq increasedproportionally to have very powerful RV's. You may use low RPM motors(980RPM) and rotate those at 1960RPM

#13596

Re: Kone...et al, diode plug update.

Overaccelerating BIG motors to reverse rotary rotor induction orcounter-rotating e fields is dangerous and can lead in lowest worstcase to a terrawatt EMP and physical implosion of unit into atemporary blackhole alike field collapse ..

Motor and everything in 30 meters will be reduced to trash ,emp willdestroy every electronic device within 600 meters and create aPERMANENT magneticanomaly that keeps growing with time .

IF experimenting in this areas I recomend to do like Norman did, putunit in safe environment within a safe perimeter and install all

posible safety devices you can place , but as NORMAN can testifyextreme Gunning of a runaway RV reving (OR any other motor can createanomalic pulses that can travel across verry thin wires , but will

burn to ashes any "bouncing" contactor it may find in its way even ifit is rated to 600VAC and 1000Amps but will not burn a 10 amp fuse inseries with it , Same phenomena occurs sometimes in semy-resonantstates fuse is in COLD node were electron density does not permit itto burn out ,or a breaker from tripping.

Take care Play safe with the toy ...

Its chrismas time !

Hector :)

#13601Re: Kone...et al, diode plug update.

Charge in a capacitor is based in an electron hole non hole 9here wego again with the holes) LOL!

OK seriously , as charge is not used its frequency is 0 , as is usedit attains the electron spin signature and kelvin ambient noise fromthe medium it travels , (that justifies stochastic resonance withinsome OU systems as (NEWMAN MOTOR ) & Bedini motors in some state are.

Its a thing to say that DC as a linear tensor is a series of STEPPEDAC signals within atomic matrix .

READ EV GRAY "stepped discharges" descripted in its patents .


45/95

the issue is we are DEALING in RF and DC is a extremely long sinewavethat can be hypersignal modulated or demodulated attaining any amountof POWER using the 0 point NODES as TAP points for this RF energy.

It is simple transformation kindergarden stuff and with theexperiments already given anyone can do it already ..

Its only to take a bit of effort to attain it and benefit from itsinmediate power savings and as a RESEARCH tool use! .

The water hammer and implosion turbines as a sample RV can be anstarter then switch to cogeneration-generation modes as unit goesself running on the water thermal noise implosion of its hydrites(sonofusion) attained in by mechanical means.

Hector

#13647Re: PMI pancake motor disassembled..... guess that voids the warranty...

In brushed designs the Stator can be made to rotate as the brushsegments are diode vectored each for TOTAL winding use instead ofonly the few segments that the brush contacts .

In a flat pancake motor using Nb magnets on the rotating Stator its111 segments are 222 diode phase bridged in 111 phases for a total of800 amperes at 12.7VDC using 222 10Ampere diodes delta phase bridge.at hi rpm and cryocooled it can power a transantlantic ... as a MotorIt can (with a properly designed 111 phases 444 transistor 111 Hnetworks suplant a 747 jet turbine ... megaherz and hypervelocity..

Sinse NASA made a night visit to H19 and took a sweep scan at thetoys, for building theirs based on MINE .

http://www.grc.nasa.gov/WWW/RT/2004/RS/RS11S-choi.html

I dump this info on electric turbine "hints"

I can make them better lighter and stronger & more efficient !

NASA ! I am aware of what you did .... and you only got what Iwanted you to have.

Also you fried one persons future for an aparent top secretdisclosure he did not made at all, I knew of it before he didIt was compromised beforehand and was even posted here in code .

I was the one that did the reverse engineering on the UFO futurecraftnot you! left brained microsoft loving nerds! Anyway I invented the

stuff in this timeline so I can understand it better than any of youassholes ...!


46/95

Want it ? PAY FOR IT ! deal face on not like thiefs in an spy movie!

want the technology ? negotiate for it ,dont try to steal what is notyours to begin with.

I am proposing Electric power airplanes sinse 1984 and most of the

info OUT there is leaked open source from RV R&D as mere toys

http://www.rctoys.com/

Look for

Brushless Electric MotorsBrushless ESC Speed Controllers

Think BIG PM RV gang some 3x3 450A 1200V transistor network to that3Phase controller and move the world to OU with off the shelve

stuff!

Modify to PM RV and OU, NASA, I *uck you!

Amen !

Hector :)

#13656Re: rotoverter peswiki update with info from patrick j. kelly pdf..

In older postings i mentioned the alternator of RV was able to ringbeing the rotor of the device like a wett finger in a grass cup , aslow stroke sets in a higer velocity stronger signal along the glassnatural resonant frequency..

Electricaly you can have a low frequency feed a higer one inintervals of shorter pulses , RV simply sometimes goes overrevingas KONE RV did riding its own rotor reversed induction waveincrementaly.

Hector

#13666Re: [EVGRAY] Re: Earths diameter being watched?

GLOBAL EXPANSION TECTONICSIn 1933, Christopher Otto Hilgenberg was the first to show that if we shrink the Earth down to 55-60 percent of its current size, then all the continents would fit together just like a jigsaw puzzle, asseen in Figure 5.2. He made the bold suggestion that this was caused by the Earth expanding in

size; at one time in the past, it really was 55 to 60 percent of its current size. The most rigorousarticle that we have found on this topic is by James Maxlow[], and shall be quoted as we proceed.


47/95

This new model is certainly not in todays college textbooks, but it has been quietly gaining in

popularity over the years. An Expanding Earth Symposium was held in Sydney, Australia in 1981,and the Smithsonian Institution hosted a discussion meeting in 1989 where these concepts andothers relating to global tectonic models were discussed. As Maxlow writes,

These arguments [at the Smithsonian meeting] indicated that there seems to be somethingquestionable with the plate tectonic theory as it is currently presented (Kremp, 1992,) and that

present concepts of plate tectonics / continental drift / polar wandering may need to be re-evaluated,revised or rejected (Smiley, 1992.)...Gustavo

#13679Re: Thanks for the comments Hector... Kone... Ash...

The PM or EM motor Used needs to be taken to syncronous rotation an

then connected ,,,

Or using a RC electric plane controller a 3 PH transistor switchnetwork connected using hi speed opto isolators using a variableamplitude power source to the drivers on your PM 3PH RV..

Some of this controllers can be computer programed for pulsewidthregulation , the world is yours with them ...

RAVEN RC development on VITEC passed & disclosed this some years ago

and RV modelmakers electronics experts took it by asault .

resulting in this TOYS you can model BIG RV technology on.

Have fun ! HEHEHEHE! :)

http://www.rctoys.com/

12 VDC controllers are the best tap the DC from the inverter secondstep (145VDC) to drive the big transistors and have PM RVS runing

at 40,000 RPM ..

Inverter battery feeds controller OPTO isolated it fires theTransistors to drive ht motor 3PH on the inverter HI voltagesection .

(Outrunner)

For that speed I recomend external rotor design, Raivo got the PMversion or MODEL of the Motors I did, any baldor DC motor with brushmotor windings that divide in 3 phase angles can be 3PHASE run using

3 or 6 brush segments and driven by this off shelve toys .

Read:


48/95

General:Brushless motors are more powerful, durable, and efficient than

brushed motors of the same size. Used in your radio controlledairplane, boat, or car, they can generate more power with longer runtimes.

What Is The Difference Between a Brushless Motor and Brushed motor?:A brushed motor uses stationary metallic contacts that 'brush'against moving metallic contacts. These 'brushes' are used totransfer electrical energy to coils on the rotating armature. A

brushless motor consists of stationary coils and a rotating magnetthat is connected to the output shaft. The coils are grouped togetherinto phases, and an electronic motor controller powers up each coilin sequence, causing the magnet to rotate.

RPM, Kv, And Current Rating:

RPM stands for the number of rotations per minute, and signifies howfast a motor spins. Brushless motors are given a Kv rating, which isRPM per volt, that lets you determine how fast that motor will rotatewith a given voltage supplied to it. A 980Kv motor powered by an11.1V battery would spin at 980 x 11.1 = 10878 RPM with no load. Thecurrent rating specifies the maximum continuous and/or burst currentthat the motor is able to handle. When selecting a battery and speedcontrol, choose ones with continuous current ratings equal to orgreater that that of the motor.

Inrunner Vs Outrunner:An inrunner motor has stationary coils which surround the rotatingmagnet at the center. An outrunner motor has stationary coils at thecenter, and the rotating magnet on the outside. Outrunner motorsgenerally have lower Kv ratings, meaning they run at a lower speed,

but with more torque, which would allow you to direct drive largerprops without needing a gearbox. Most RC cars and boats would requirean inrunner brushless motor.

_END____________________________

145VDC x 980kv (RV) = 142,100 RP

Hector Posts Volume3

Documents

Transcript of Hector Posts Volume3