12:22 PM 01/10/11

JG Electronics

Item Price List 1 October 2011

T T ( th

Item Transfer Surface Transfer Method Orientation Press to use Paper to use Mirror ?

Temp (4-in-1-press)

Temp (other presses) -

centigrade PressureTime (seconds) Time Minutes Extra InstructionsItem Transfer Surface Transfer Method Orientation Press to use Paper to use Mirror ? press) centigrade PressureTime (seconds) Time Minutes Extra Instructions

Apron Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Cover the trim with paper to prevent it's colour from transferring onto the press or heat pad. Don't make the pressure too tight, otherwise the material will crinkle around the trim

Apron Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot - same things as above apply thoughApron Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot - same things as above apply though

Apron Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot - pressure must be high for laser paper, so some crinkling of the material near the trim will occur.

Baby Bib Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Cover the trim with paper to prevent it's colour from transferring onto the p Don't make the pressure too tight, otherwise the material will crinkle around the trimy y p p p p p g p p g ,Baby Bib Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot - same things as above apply though

Baby Bib Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot - pressure must be high for laser paper, so some crinkling of the material near the trim will occur.

Backpack Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Backpack Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Backpack Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Bag Cosmetic Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

B C ti I kj t F Fl t / T hi t H t l (J tt H) Mi 360 200 M di 20 P l H tBag Cosmetic Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Bag Cosmetic Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Bag Econo Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 For best results tape the transfer down on 2 sides with heat tape before pressingBag Econo Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 For best results tape the transfer down on 2 sides with heat tape before pressing

Bag Flex Black Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Bag Flex Black Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hotag e ac je ace up a / s o pee (Je a s ) o 360 00 ed u 0 ee o

Bag Flex Black Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Bag Gym with Drawstring Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium Lig 75 Do not press onto the drawstring else it will melt

Bag Shoulder (all sizes) Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Bag Shoulder (all sizes) Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Bag Shoulder (all sizes) Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Bag Wine Cooler Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Cover the trim with paper to prevent it's colour from transferring onto the p Don't make the pressure too tight, otherwise the material will crinkle around the trimB Wi C l I kj t F Fl t / T hi t H t l (J tt H) Mi 360 200 M di 20 P l H t thi b l th hBag Wine Cooler Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot - same things as above apply though

Bag Wine Cooler Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot - pressure must be high for laser paper, so some crinkling of the material near the trim will occur.

Bag Wood Black Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1 5 Cover the trim with paper to prevent it's colour from transferring onto the p Don't make the pressure too tight otherwise the material will crinkle around the trimBag Wood Black Coated Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Cover the trim with paper to prevent it s colour from transferring onto the p Don t make the pressure too tight, otherwise the material will crinkle around the trimBag Wood Black Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot - same things as above apply though

Bag Wood Black Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot - pressure must be high for laser paper, so some crinkling of the material near the trim will occur.Bag Wood Black Laser Face up Flat / T shirt Classic Mirror 360 200 High 22 Peel Hot pressure must be high for laser paper, so some crinkling of the material near the trim will occur.

Balloons Coated Foil Paper Inkjet N/A No press used The Balloon itself Don't mirror N/A N/A N/A N/A Print these directly in your inkjet printer - no heat is used

Buttons Metal with mylar film Inkjet / Laser N/A Badge Press Plain paper Don't mirror N/A N/A N/A N/A These are done with a badge press, and are printed on plain paper.

Crystals Crystal Inkjet N/A No press used Crystal Paper Don't mirror N/A N/A N/A N/A You need the crystal system, or at the very least, the crystal paper, crystal glue and the sun - ask for details.

Camisole Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Light 90 1.5 If the pressure is too high, the area around the transfer paper will leave an Don't make the pressure too tight, otherwise the material will crinkle around the trimCamisole Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Camisole Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

C C l P l t S bli ti F Fl t / T hi t T i t Mi 340 200 M di 90 1 5 A th l i it' b t t d d k it i thCan Cooler Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 340 200 Medium 90 1.5 As the cooler is pre-sewn it's best to wrap around a mug and make it in the mug press

Can Cooler Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Can Cooler Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel HotCan Cooler Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Cap White Cotton Sublimation Face up Cap Hot Peel (Jettrans H) Mirror 360 200 Medium 20 As this is cotton, you must use the cotton transfer paper

Cap White Inkjet Face up Cap Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel HotCap White Inkjet Face up Cap Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Cap White Laser Face up Cap Classic + Mirror 360 200 High 22 Peel Hot

Cap Coloured (Black etc.) Cotton Sublimation Face up Cap 1-step (Jet-opaque) Don't mirror 360 200 Light 15 If you press too hard then the colour of the cap will come through the print. Use with silicone paper

Cap Coloured (Black etc.) Sublimation Face up Cap Sublimation flock Mirror 360 200 Medium 60 1 Follow the instructions specific to sublimation flock

Cap Coloured (Black etc.) Inkjet Face up Cap 1-step (Jet-opaque) Don't mirror 360 200 Light 20 If you press too hard then the colour of the cap will come through the print. Use with silicone paper

Cap Coloured (Black etc.) Laser Face up Cap 1-step Laser Don't mirror 360 200 Light 22 If you press too hard then the colour of the cap will come through the print. Use with silicone paper

Clock Face Metal Clock Face Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 80 Peel the plastic protective sheet from the metal before transferring. Use heat tape to stick the picture to the metal.

C t Fl ibl ith C k B P l t S bli ti F Fl t / T hi t T i t Mi 340 190 M di 50 D 't th i t i l ill b bblCoaster - Flexible with Cork Base Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 340 190 Medium 50 Don't overpress otherwise material will bubble

Coasters - Rubber polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5

Coasters Rubber Inkjet Face up Flat / T shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel HotCoasters - Rubber Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Coasters - Rubber Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Coasters Wood polyester vinyl Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 120 Allow to cool for a few seconds before removing heat tapeCoasters Wood polyester vinyl Sublimation Face up Flat / T shirt Texprint Mirror 360 200 Medium 120 Allow to cool for a few seconds before removing heat tape

Coasters Glass coated glass Sublimation Face Down Flat / T-shirt Texprint Don't mirror 360 200 Medium 360 6 to 7 Print goes against white side. Allow to cool for a few seconds before removing heat tape. White surface is soft when hot - take care not to scratch it. Use a nomex pad for best results

Cushions / Pillows Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 Place a sheet of plain paper in the cushion to prevent the colour on the back from transferring through the cushion

Cushions / Pillows Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Place a sheet of plain paper in the cushion to prevent the colour on the back from transferring through the cushion

Cushions / Pillows Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Place a sheet of plain paper in the cushion to prevent the colour on the back from transferring through the cushion

Cushion Stadium Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80

Cushion Stadium Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

C hi St di L F Fl t / T hi t Cl i Mi 360 200 Hi h 22 P l H tCushion Stadium Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Dog Collar Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 Use heat tape stick the print to the printable area. Don't press the clasp or it will melt.

Dog Collar Inkjet Face up Flat / T shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot Don't press the clasp or it will meltDog Collar Inkjet Face up Flat / T-shirt Hot peel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot. Don t press the clasp or it will melt.

Dog Collar Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot. Don't press the clasp or it will melt.

Doming Items Metal Inkjet Face Up Flat / T-shirt Doming paper Mirror N/A N/A N/A N/A Use the doming kit - no heat or pressingDoming Items Metal Inkjet Face Up Flat / T shirt Doming paper Mirror N/A N/A N/A N/A Use the doming kit no heat or pressing

Flag Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 Use heat tape stick the print to the printable area.

Flip Flop Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 Use heat tape stick the print to the printable area. Insert the straps with a pair of long nose pliers and a screw driver once printed

Fridge Magnets Polyester Vinyl Sublimation Face up Flat / T-shirt Texprint Mirror 300-340 185 Medium N/A See specific instructions for magnetic items supplied with the item

Glass - 16oz - Cone shaped Glass Sublimation Mug Press or Oven Texprint Mirror 340 185 Medium 240 4 If using a mug press, then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 8-12 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Glass - 300ml Frosted (Highball) Glass Sublimation Oven only Texprint Mirror 380 200 High 8 to 12 If using a mug press, then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 8-12 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Glass - Shot / Tot Glass Sublimation Oven only Texprint Mirror 380 200 High 8 to 12 If using a mug press, then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 8-12 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Gl Whi k Gl S bli ti M P O T i t Mi 295 170 M di 600 10 If i th 10 i t di If d i i th 8 i t id d b th l t t b 200C d th t b ti htl t k t th l ith l t f h t t id t d b ttGlass - Whiskey Glass Sublimation Mug Press or Oven Texprint Mirror 295 170 Medium 600 10 If using the mug press - 10 minutes - medium pressure. If doing in the oven 8 minutes upside down - both elements to be on - 200C and the paper must be tightly stuck onto the glass with lots of heat tape - sides, top and bottom

Glass Cutting Board / Placemat Glass Sublimation Face Down Texprint Don't mirror 360 200 Medium 360 6 Print goes against white side. Allow to cool for a few seconds before removing heat tape. White surface is soft when hot - take care not to scratch it. Use a nomex pad for best results

Glass Beer Mug Frosted Glass Sublimation Mug Press or Oven Texprint Mirror 340 190 High 270 4 5 Preheat Glass in an oven or hot water before applying print otherwise it will crack in the mug press If using oven tape print tightly on sides top bottom and through the middle with heat tape 200C make sure both elements are on 10 minutes or more (depending on your oven)Glass Beer Mug - Frosted Glass Sublimation Mug Press or Oven Texprint Mirror 340 190 High 270 4.5 Preheat Glass in an oven or hot water before applying print, otherwise it will crack in the mug press. If using oven, tape print tightly on sides, top, bottom and through the middle with heat tape - 200C - make sure both elements are on - 10 minutes or more (depending on your oven).

Glass Beer Mug - Clear Glass Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using oven, tape print tightly on sides, top, bottom and through the middle with heat tape - 200C - make sure both elements are on - 10 minutes.

Glass with handle - 11oz - Clear / Frosted Glass Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using oven, tape print tightly on sides, top, bottom and through the middle with heat tape - 200C - make sure both elements are on - 10 minutes.Glass with handle 11oz Clear / Frosted Glass Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using oven, tape print tightly on sides, top, bottom and through the middle with heat tape 200C make sure both elements are on 10 minutes.

Glass Clock Large Glass Sublimation Face Down Flat / T-shirt Texprint Don't mirror 360 200 Medium 360 6 Print goes against white side. Allow to cool for a few seconds before removing heat tape. White surface is soft when hot - take care not to scratch it. Use a nomex pad for best results

Glass Cloth (lens cleaning cloth) Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 Can be printed both sides

Jewellery Boxes Ceramic Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 360 6 Apply paper to tile, and flip over (face down). Press on the back of the tile. A Nomex pad gives best results

Keyring - Animal with mini shirt Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80 Use heat tape stick the print to the printable area.

Keyring - Animal with mini shirt Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Keyring - Animal with mini shirt Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

K i Pl ti Pl ti I kj t / L N/A N d Pl i D 't i N/A N/A N/A N/A P i t th i t l i d t it i t th th k i d li l dKeyring - Plastic Plastic Inkjet / Laser N/A No press used Plain paper Don't mirror N/A N/A N/A N/A Print the image onto plain paper, and put it into the recess on the keyring and clip closed

Keyring - Metal (all metal keyrings) Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Use heat tape stick the metal to the printable area.

Keyring Polymer Double sided with coloured edge Polyester Sublimation Face up Flat / T shirt Texprint Mirror 340 185 High 90 1 5 Tape the image on with heat tape If you want to press the second side flip it over apply the print and press for another 90 seconds The assemble the keyringKeyring - Polymer - Double sided with coloured edge Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 340 185 High 90 1.5 Tape the image on with heat tape. If you want to press the second side flip it over, apply the print and press for another 90 seconds. The assemble the keyring.

Lanyard Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Tape the image on with heat tape

Lanyard Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel hotLanyard Inkjet Face up Flat / T shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel hot

Lanyard Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel hot

Magnetic Sheet A4 Polyester Vinyl Sublimation Face up Flat / T-shirt Texprint Mirror 300-340 185 Medium N/A See specific instructions for magnetic items supplied with the itemg y y g

Metal Sheets Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film, then apply the image to the metal. Secure it will heat tape. Press upside down (facedown)

Metal Notebook Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 There is no protective film to peel here - just apply the image to the metal. Secure it will heat tape. Press upside down (facedown). Done press too close to the inner edge otherwise you will damage the mechanism of the notebook

Metal-Bag-Hanger Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 80 Remove the protective plastic film on the metal disc, then apply the image to the metal. Secure it will heat tape. Press upside down (facedown). Then use the included double sided tape to secure the printed disk to the bag hanger.

Metal Business Card Holders - Wave & Cut corner Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 120 2 Insert the 2 rubber pieces (with the white facing outwards) into the holder, before pressing. This will prevent the card holder from distorting or bending in the press. The rubber can be re-used 5-7 times. Using a nomex pad will give better results

M t l B i C d H ld St i l St l M t l I t S bli ti F D Fl t / T hi t T i t Mi 360 200 M di 90 1 5 R th t ti l ti fil th l th i t th t l S ith h t t d id d (f d ) Th ti k th i t d t l t th it ith th id d d bl id d t (l k lik ll ll h t f )Metal Business Card Holder - Stainless Steel Metal Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film, then apply the image to the metal. Secure with heat tape and press upside down (facedown). Then stick the printed metal onto the unit with the provided double sided tape (looks like a yellow small sheet of paper)

Metal Cigarette Case Metal Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film, then apply the image to the metal. Secure with heat tape and press upside down (facedown). Then stick the printed metal onto the unit with the provided double sided tape (looks like a yellow small sheet of paper)

Metal Coat Rack Metal / Ceramic Insert Sublimation Face Down Flat / T shirt Texprint Mirror 360 200 Medium 90 1 5 You press either onto tiles or metal and insert into the coat rackMetal Coat Rack Metal / Ceramic Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 You press either onto tiles or metal and insert into the coat rack

Metal-Compact mirrors Metal Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film, then apply the image to the metal. Secure with heat tape and press upside down (facedown). Then stick the printed metal onto the unit with the provided double sided tape (looks like a yellow small sheet of paper)

Metal-Hip Flask Metal Sublimation Upside Down Oven only Texprint Mirror 380 200 High 420 7 to 10 Remove Cap, Tape Image down as per picture here (tape the 4 corners 1st, the in the numbered sequence shown). Put in a household oven with both elements on (top and bottom), upside down (so heat can enter flask)Metal Hip Flask Metal Sublimation Upside Down Oven only Texprint Mirror 380 200 High 420 7 to 10 Remove Cap, Tape Image down as per picture here (tape the 4 corners 1st, the in the numbered sequence shown). Put in a household oven with both elements on (top and bottom), upside down (so heat can enter flask)

Metal-ID Tag Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 If printing only the 1-side, peel the protective clear plastic off the metal, then press facedown for 90 seconds. If you want to print both sides, then put the print on each side. Press the 1st side (top) for 60 seconds, and then remove the paper, flip over (so the bottom side is now facing up), and press for another 60 seconds.

Metal Key Rack Metal / Ceramic Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 You press either on a tile or metal sheet and insert into the key racky p p y

Metal-Lighter (Zippo Type) Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Light 180-300 3 to 6 Tape the paper firmly onto the lighter with heat tape. Do NOT remove the insides of the lighter, and don't fill it with lighter fluid before pressing. If you are printing only 1 side, press facedown onto a nomex pad for 3 minutes (180 sec). If you want to press both sides, apply the printed paper to each side, and press initially for 180 sec, then take off paper from top of lighter (side facing upwards), turn it over (so the bottom is now at the top), and press for a further 2 minutes (120 seconds)

Metal-Luggage Tag Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 If printing only the 1-side, peel the protective clear plastic off the metal, then press facedown for 90 seconds. If you want to print both sides, then put the print on each side. Press the 1st side (top) for 60 seconds, and then remove the paper, flip over (so the bottom side is now facing up), and press for another 60 seconds.

Metal-Pendant-GPP002 Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film, then apply the image to the metal. Secure it with heat tape. Press upside down (facedown)

Mousepad Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5

M d I kj t F Fl t / T hi t H t l (J tt H) Mi 360 200 M di 20 P l H tMousepad Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Mousepad Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Mugs Ceramic 15oz / 11oz / 10oz all types Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using a mug press you may need to change elements (use the one with the thick rubber for 10oz Mugs & Beer Mugs) if you have a mug press from us Then tape the image tightly on with heat tape before putting the mug in the press Don't wait for the press to heat up just do the 1st mug (if the press is cold for 4 5 minutes) If using an oven tape he print tightly on sides top bottom and through the middle with heat tape Then put upside down (so the rising heat goes into the mug) on a baking tray Set the oven to 200C make sure both oven elements are on (top and bottom) The process should take 10 14 minutes depending on the oven some experimentation will be required to get the right settings for your ovenMugs - Ceramic 15oz / 11oz / 10oz - all types Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using a mug press, you may need to change elements (use the one with the thick rubber for 10oz Mugs & Beer Mugs) if you have a mug press from us. Then tape the image tightly on with heat tape, before putting the mug in the press. Don t wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug 3oz / 5oz / Espresso Ceramic Sublimation Oven only Texprint Mirror 380 200 Medium 10+ Tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-15 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Beer Mugs 20oz & 22oz Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using our mug press, change to the element with the thicker rubber. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.Mug Beer Mugs 20oz & 22oz Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using our mug press, change to the element with the thicker rubber. Then tape the image tightly on with heat tape, before putting the mug in the press. Don t wait for the press to heat up just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C make sure both oven elements are on (top and bottom). The process should take 10 14 minutes depending on the oven some experimentation will be required to get the right settings for your oven.

Mug Black & Mug Glow Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 With these mugs the image will only transfer in the band around the mug even if your image is larger. Tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Cone Shaped Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using our mug press, change to the cone shaped element. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.g g g g g g g y g g j g ( ) g g y g ( g g g) g y ( ) g g g g y

Mug Espresso Plastic / Polymer Polymer Sublimation Mug Press or Oven Texprint Mirror 330 180 Medium 120 2 Insert the Tool for the plastic mug into the mug. This is to prevent the mug deforming with the heat of the press or oven. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug if the press is cold for 3 minutes. If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 5-7 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Flasks & Sports bottles Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using our mug press, change to the element with the thicker rubber. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st unit (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the item) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 8-12 minutes depending on the oven - some experimentation will be required to get the right settings for your oven. If using the oven you can print the entire surface of the item (straight part only).

Mug Pencil Caddy / Piggy Bank Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 If using a mug press, you may need to change elements (use the one with the thick rubber for 10oz Mugs & Beer Mugs) if you have a mug press from us. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Travel Mug - Stainless Steel Metal Sublimation Mug Press only Texprint Mirror 340 190 Medium 240 4 As this mug has a plastic handle, you cannot put it in the oven - only the mug press. Tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes).

M T l M ith Pl ti i M t l S bli ti M P O T i t Mi 340 190 Li ht 240 4 R th l ti i l i l th t l t b d T th i ti htl ith h t t b f tti th i th U li ht t t th t l t b d f di t ti D 't it f th t h t j t d th 1 t (if th i ld f 4 5 i t ) If i t th i t ti htl id t b tt d th h th iddl ith h t t Th t b ki t S t th t 200C k b th l t (t d b tt ) Th h ld t k 10 14 i t d di th i t ti ill b i d t t th i ht tti fMug Travel Mug with Plastic inner Metal Sublimation Mug Press or Oven Texprint Mirror 340 190 Light 240 4 Remove the plastic inner, leaving only the metal outer band. Tape the image tightly on with heat tape, before putting the mug in the press. Use light pressure to prevent the metal outer band from distorting. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Travel Mug - Plastic / Polymer Polymer Sublimation Mug Press or Oven Texprint Mirror 330 180 Medium 120 2 Insert the Tool for the plastic mug into the mug. This is to prevent the mug deforming with the heat of the press or oven. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug if the press is cold for 3 minutes. If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 5-7 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug Triangle Ceramic Sublimation Oven only Texprint Mirror 380 200 Medium 10+ Tape the print tightly on sides top bottom and through the middle with heat tape Then put upside down (so the rising heat goes into the mug) on a baking tray Set the oven to 200C make sure both oven elements are on (top and bottom) The process should take 10 15 minutes depending on the oven some experimentation will be required to get the right settings for your ovenMug Triangle Ceramic Sublimation Oven only Texprint Mirror 380 200 Medium 10+ Tape the print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-15 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug White Plastic / Polymer Polymer Sublimation Mug Press or Oven Texprint Mirror 330 180 Medium 120 2 Insert the Tool for the plastic mug into the mug. This is to prevent the mug deforming with the heat of the press or oven. Then tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug if the press is cold for 3 minutes. If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 5-7 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Mug White 11oz Ceramic Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 Tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 10-14 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.Mug White 11oz Ceramic Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 240 4 Tape the image tightly on with heat tape, before putting the mug in the press. Don t wait for the press to heat up just do the 1st mug (if the press is cold for 4.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C make sure both oven elements are on (top and bottom). The process should take 10 14 minutes depending on the oven some experimentation will be required to get the right settings for your oven.

Mug White 11oz Ceramic Dishwasher Safe Ceramic Sublimation Mug Press or Oven Texprint Mirror 340 190 Medium 270 4.5 The dishwasher safe coating requires that the mug be pressed for a little longer than a standard mug. Tape the image tightly on with heat tape, before putting the mug in the press. Don't wait for the press to heat up - just do the 1st mug (if the press is cold for 5.5 minutes). If using an oven, tape he print tightly on sides, top, bottom and through the middle with heat tape. Then put upside down (so the rising heat goes into the mug) on a baking tray. Set the oven to 200C - make sure both oven elements are on (top and bottom). The process should take 11-15 minutes depending on the oven - some experimentation will be required to get the right settings for your oven.

Napkin Holder Ceramic Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 360 6 For this item, you print on a tile which goes into the holder. Apply the image to the tile with heat tape, so that the paper wraps over the edge of the tile, and the tape sticks to the back of the tile. For best results lay a nomex pad down onto the pad of the heat press, and press the tile face down for 6 minutes.p p y p g pp y g p p p p g p y p p p p

Pencil Bag Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Pencil Bag Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Pencil Bag Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Photoglobe Snow / Hearts No transfer just laser / inkjet print inserted N/A N/A No press used Plain paper Don't mirror N/A N/A N/A N/A N/A Print onto plain paper with either an inkjet or laser printer, insert into the snowglobe, the apply a spot of glue to glue the base onto the unit (so the customer can buy another one if they want to change the picture). Don't use a sublimation print as it will fade very quickly. Sublimation is for transfers only.

Pl t R bb P l t S bli ti F Fl t / T hi t T i t Mi 360 200 M di 90 1 5Placemat - Rubber Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5

Placemat - Rubber Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Placemat Rubber Laser Face up Flat / T shirt Classic + Mirror 360 200 High 22 Peel HotPlacemat - Rubber Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Placemat - Wooden Wood Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 3.5 Apply print with heat tape. Take care when peeling not to damage coating on the wood, as it's soft when hot.

Plate - Side - Ceramic or Polymer (Plastic) Ceramic / Polymer Sublimation Face up Plate / Flat with plate puckTexprint Mirror 240 to 275 200 medium High 5 to 6 If using our Muggit 4-in-1 press with the side plate attachment set the min temp to 240 and the max temp to 275 Set the time to 300 Wait for the press to reach 240 Insert the plate and push the start button on the controller (right hand most button) The press will heat to 275 and then count down from 300 If you are using a plate puck with a T-shirt press then preheat the puck and set the press to 200C Press for 6 to 7 minutesPlate Side Ceramic or Polymer (Plastic) Ceramic / Polymer Sublimation Face up Plate / Flat with plate puckTexprint Mirror 240 to 275 200 medium High 5 to 6 If using our Muggit 4 in 1 press with the side plate attachment, set the min temp to 240, and the max temp to 275. Set the time to 300. Wait for the press to reach 240. Insert the plate, and push the start button on the controller (right hand most button). The press will heat to 275, and then count down from 300. If you are using a plate puck with a T shirt press then preheat the puck, and set the press to 200C. Press for 6 to 7 minutes.

Plate Dinner Ceramic Sublimation Face up Plate / Flat with plate puckTexprint Mirror 200 to 270 200 medium High 5 to 6 Pre-heat the plate either in an over to 50C or in warm water. This is essential else the plate will crack in the press. If using our Muggit 4-in-1 press with the dinner plate attachment, set the min temp to 200, and the max temp to 270. Set the time to 300. Wait for the press to reach 200. Insert the plate, and push the start button on the controller (right hand most button). The press will heat to 270, and then count down from 300. If you want to do another plate, wait for the press to cool down to 200. If you are using a plate puck with a T-shirt press then preheat the puck, and set the press to 200C. Press for 6 to 7 minutes.

Puzzle - Gloss (all gloss ones) Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5( g ) y p p

Puzzle - Magnetic Polyester Vinyl Sublimation Face up Flat / T-shirt Texprint Mirror 300-340 185 Medium N/A See specific instructions for magnetic items supplied with the item

Puzzle - Matte Polyester Fabric Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 80

Puzzle - Matte Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Puzzle - Matte Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

P l P l (Pl ti ) P l S bli ti F U Fl t / T hi t T i t Mi 320 175 M di Hi 90 1 5 A l i t t l P f 90 d O d fli l ith l i d f 90 d th b k f l t t i ht If t t i t th 2 d id ll l th i t d f 2 i t i t dPuzzle - Polymer (Plastic) Polymer Sublimation Face Up Flat / T-shirt Texprint Mirror 320 175 Medium Hi 90 1.5 Apply print to puzzle. Press for 90 seconds. Once done, remove paper, flip puzzle over, cover with plain paper and press for 90 seconds on the back for puzzle to straight up. If you want to print the 2nd side as well, apply the print, and press for 2 minutes instead.

Soup Bowl Ceramic Sublimation Upside Down Oven Only Texprint Mirror 380 200 Very High 10 to 15 Apply print with heat tape, stretch as tightly as possible round the whole bowl. Then apply a piece around the entire rim and base. Put upside down on baking tray at 200C. Make sure both oven elements are on. Leave for 10 - 15 minutes. Exact times will vary according to your oven.

Stone M Stone Sublimation Face Down / Face up Flat / T shirt Texprint Mirror 360 200 Medium High 5 to 7 1st check that stone is even on front and rear as if the stone is uneven it could affect your transfer If in any doubt ask us Apply the print and if you have done stone before place face down on a nomex pad and press for 6 to 7 minutes Use Medium High pressure If you've done Stone before press face up for 5 minutes Face up gives better detail but is more difficult to get rightStone - M Stone Sublimation Face Down / Face up Flat / T-shirt Texprint Mirror 360 200 Medium High 5 to 7 1st check that stone is even on front and rear as if the stone is uneven it could affect your transfer. If in any doubt ask us. Apply the print and if you have done stone before place face down on a nomex pad, and press for 6 to 7 minutes. Use Medium High pressure. If you ve done Stone before, press face up for 5 minutes. Face up gives better detail, but is more difficult to get right.

Sublimation badge Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 Remove the protective plastic film, then apply the image to the metal. Secure it with heat tape. Press upside down (facedown)

Sunshade Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressingSunshade Polyester Sublimation Face up Flat / T shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Sunshade Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Sunshade Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hotp g

Tie Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Light 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Tie Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Tie Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Tiles - Ceramic Ceramic Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 6 to 7 Apply the image to the tile with heat tape, so that the paper wraps over the edge of the tile, and the tape sticks to the back of the tile. For best results lay a nomex pad down onto the pad of the heat press and the tile face down into the nomex. Press 6 to 7 minutes.Tile - Glass Glass Sublimation Face Down Flat / T-shirt Texprint Don't mirror 360 200 Medium 6 to 7 Print goes against white side. Allow to cool for a few seconds before removing heat tape. White surface is soft when hot - take care not to scratch it. Use a nomex pad for best results

Toys (Monkey / Teddy etc.) Polyester (The shirt of the toy) Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Light 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Toys (Monkey / Teddy etc ) Inkjet Face up Flat / T shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel HotToys (Monkey / Teddy etc.) Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Toys (Monkey / Teddy etc.) Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 22 Peel Hot

Trophies - Oval / Rect / Round / Shield etc Wood Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 35 Use heat tape to fasten the image to the trophy After pressing take extreme care when peeling the heat tape so that it doesn't pull any of the trophy's varnish offTrophies Oval / Rect / Round / Shield etc. Wood Sublimation Face up Flat / T shirt Texprint Mirror 360 200 Medium 35 Use heat tape to fasten the image to the trophy. After pressing, take extreme care when peeling the heat tape so that it doesn t pull any of the trophy s varnish off.

T-shirt Black / Coloured Cotton / Polycotton / Polyester Sublimation Face up Flat / T-shirt 1-step (Jet-opaque) Don't mirror 360 200 Light 15 If you press too hard then the colour of the cap will come through the print. Use with silicone paper

T-shirt Black / Coloured Sublimation Face up Flat / T-shirt Sublimation flock Mirror 360 200 Medium 60 1 Sublimation flock is MUCH more permanent than 1-step paper. This is the better paper. Refer to instructions that come with the paper.p p p p p p p p p

T-shirt Black / Coloured Inkjet Face up Flat / T-shirt 1-step (Jet-opaque) Don't mirror 360 200 Light 20 If you press too hard then the colour of the cap will come through the print. Use with silicone paper

T-shirt Black / Coloured Laser Face up Flat / T-shirt 1-step Laser Don't mirror 360 200 Light 22 If you press too hard then the colour of the cap will come through the print. Use with silicone paperT-shirt Black / Coloured Inkjet / Laser Face Up Flat / T-shirt 2-Step Blanco Mirror 360 200 Medium 20 to 60 This paper can be used in conjunction with the paper for the light shirts (Jettrans H on the inkjet and Laser Classic Plus on the Laser), and is a material. You transfer onto this material, and this material is then pressed onto the dark shirt. This give far superior wash resistance to the 1-step papers, but is more expensive - refer to the instructions for this paper.

T-shirt / Golf shirt White Cotton / Polycotton Sublimation Face up Cap Hot Peel (Jettrans H) Mirror 360 200 Medium 20 Even though the shirt might be polycotton, there is too little polyester for the print to come out well. It will look very faded. It's better to use the cotton transfer paper instead

/ I kj F C H l (J H) Mi 360 200 M di 20 P l HT-shirt / Golf shirt White Inkjet Face up Cap Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

T-shirt / Golf shirt White Laser Face up Cap Classic + Mirror 360 200 High 22 Peel Hot

T shirt / Golf shirt White Polyester Sublimation Face up Flat / T shirt Texprint Mirror 360 200 Light 90 1 5 Don't use too much pressure otherwise you will leave a permanent outline of the edges of the paper on the shirtT-shirt / Golf shirt White Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Light 90 1.5 Don t use too much pressure, otherwise you will leave a permanent outline of the edges of the paper on the shirt.

T-shirt Honeycomb / V-neck / Luxury (white) 100% Cotton Inner + 100% Polyester Outer Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Light 90 1.5 Don't use too much pressure, otherwise you will leave a permanent outline of the edges of the paper on the shirt.

Unisub Keyring Divot Metal Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1 5 Remove the protective plastic film from the round metal insert then apply the image to the metal Secure it with heat tape Press upside down (facedown) Once done stick the insert to the divot with double-sided tapeUnisub Keyring Divot Metal Insert Sublimation Face Down Flat / T shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film from the round metal insert, then apply the image to the metal. Secure it with heat tape. Press upside down (facedown). Once done stick the insert to the divot with double sided tape

Unisub Pet Tags Metal Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove the protective plastic film from the round metal insert, then apply the image to the metal. Secure it with heat tape. Press upside down (facedown).

Unisub Streamline Krystal / Crystal White Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 60 1 Remove the protective plastic / paper film. Use heat tape to secure image. Take care when removing heat tape not to damage varnished wood area.y y y p p p p p p p g g p g

Vase Ceramic Sublimation Oven only Texprint Mirror 360 200 High 10 to 15 Apply print with heat tape, stretch as tightly as possible round the whole bowl. Then apply a piece around the entire rim and base. Put upside down on baking tray at 200C. Make sure both oven elements are on. Leave for 10 - 15 minutes. Exact times will vary according to your oven.

Videoflex - Transfer Vinyl - Std Colours Polyurethane Vinyl Cut Face up Flat / T-shirt Videoflex Reverse Cut 340 180 Medium 20 Cut from the back of the material. Remove what you don't want, apply face down on the shirt. Press for 20 seconds, peel carrier sheet when shirt has cooled. If you want to press more than 1 colour, press 1st colour for 4 seconds, 2nd colour for 4 sec, 3rd colour for 4 sec and so on. Once shirt has cooled and you've removed carrier sheet, cover with Teflon and press for a further 12 seconds. Peel Teflon cold.

Videoflex - Transfer Vinyl - Metallic, Neons etc. Polyurethane Vinyl Cut Face up Flat / T-shirt Videoflex Reverse Cut 320 170 Medium 18 Cut from the back of the material. Remove what you don't want, apply face down on the shirt. Press for 20 seconds, peel carrier sheet when shirt has cooled. If you want to press more than 1 colour, press 1st colour for 4 seconds, 2nd colour for 4 sec, 3rd colour for 4 sec and so on. Once shirt has cooled and you've removed carrier sheet, cover with Teflon and press for a further 12 seconds. Peel Teflon cold.

VideoFlex Refl HR 510 - Reflective PVC Vinyl Cut Face up Flat / T-shirt Videoflex Reverse Cut 280-320 135-170 Medium 15 Remove blue protective film from rear, then reverse cut (mirror). Weed areas not wanted. Apply to shirt and press at 135C (280) for 15 seconds. Peel warm. When shirt cools, cover with Teflon, press at 170C (320) for 10 seconds after covering with Teflon.

W ll ( ll i d ) P l S bli i F Fl / T hi T i Mi 360 200 M di 90 1 F b l h f d 2 id i h h b f iWallets (all sizes and types) Polyester Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 For best results tape the transfer down on 2 sides with heat tape before pressing

Wallets (all sizes and types) Inkjet Face up Flat / T-shirt Hotpeel (Jettrans H) Mirror 360 200 Medium 20 Peel Hot

Wallets (all sizes and types) Laser Face up Flat / T shirt Classic + Mirror 360 200 High 21 Peel HotWallets (all sizes and types) Laser Face up Flat / T-shirt Classic + Mirror 360 200 High 21 Peel Hot

Wood - Award Plaque Metal Insert Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 90 1.5 Remove any protective plastic film from the flat metal sheet, then apply the image to the metal. Secure it with heat tape. Press upside down (facedown). Once done stick the metal to the wooden award plaque with double-sided tape.

Wood - Notebook Wood Sublimation Face up Flat / T-shirt Texprint Mirror 360 200 Medium 35 Use heat tape to fasten the image to the cover After pressing take extreme care when peeling the heat tape so that it doesn't pull any of the varnish offWood Notebook Wood Sublimation Face up Flat / T shirt Texprint Mirror 360 200 Medium 35 Use heat tape to fasten the image to the cover. After pressing, take extreme care when peeling the heat tape so that it doesn t pull any of the varnish off.

Wood - Pencil Caddy Ceramic Sublimation Face Down Flat / T-shirt Texprint Mirror 360 200 Medium 6 to 7 For this item, you actually print on 2 tiles and apply them to the sides of the pencil caddy (holder). Apply the image to the tile with heat tape, so that the paper wraps over the edge of the tile, and the tape sticks to the back of the tile. For best results lay a nomex pad down onto the pad of the heat press and the tile face down into the nomex. Press 6 to 7 minutes.

TERMS USED IN THIS MANUAL

FACEDOWN FACE UPThis means that the print is applied to the printable surface of the item, then the item is flipped over, so that the back of the item is facing youp pp p , pp , g ywhen the press is closed, the heat element (which is at the top), presses onto the BACK of the item, and the heat transfers through the item to the print. This means that the print is applied to the printable surface of the item, and that the item is left facing upwards, so that when the press

is closed, the heat element presses onto the back of the transfer paper, and the heat goes directly to the front of the item through the print.The white material under the print and the tile is the nomex pad.

The white pad in the background is the nomex pad

OVEN TIMESOVEN TIMES

The time that an item goes into the oven is an estimate. Every different oven, will need a different time. Please experiment until you find the correct time for your oven.

USING AN OVEN - SOME TIPS

Whatever you are putting in the oven must always go in upside down - As hot air rises, it will be trapped inside the item, thus heating it more evenly.

E b h l f h d if h h f l i S h 200CEnsure both elements of the oven are on, and if you have a thermofan, please use it. Set the oven to 200C.

If you find that some areas of the item transfer beautifully but a section just next to it doesn't this indicates that the oven temp is not even In this case take 2 metal sheets the size of a baking tray and drillIf you find that some areas of the item transfer beautifully, but a section just next to it doesn t, this indicates that the oven temp is not even. In this case, take 2 metal sheets the size of a baking tray, and drill

them full of holes - the more the better. Put 1 metal sheet on the lowest tray of the oven (so the heat from the bottom element has to go through the holes),

and the 2nd sheet just below the top element.a d e d s ee jus be o e op e e e

Page 1 of 2