Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research...
Transcript of Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research...
![Page 1: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/1.jpg)
International Research Journal of Applied and Basic Sciences. Vol., 3 (4), 758-769, 2012
Available online at http://www. irjabs.com
ISSN 2251-838X ©2012
Heat Conduction of a Hollow Cylinder via Generalized Hankel Transform
A. M. Shafei, S. Rafee Nekoo*
Ph.D. Student of Mechanical Engineering, School of Mechanical Engineering, Iran University of Science
and Technology, P.O. Box 1684613114, Tehran, Iran �
�Correspondent Author, Email: [email protected]
ABSTRACT: In this work, the heat conduction problem of a finite hollow cylinder is
solved as an exact solution method. In order to solve the PDE equation, generalized finite
Hankel and other integral transformations are used. Two case studies for simulations are
presented and verified with simulations which extracted from finite element method. The
results are shown that this approach is proper for solving heat conduction problems in
cylindrical coordinate.
Keywords: Generalized Finite Hankel Transform; Hollow Cylinder; Finite Element; Heat
Conduction
Introduction
Direct measurement of distribution of temperature is difficult and not possible some times. For dealing
with this problem, different methods have been used. In (Sermet, 2012) a new Green’s function in closed
form was introduced for a boundary value problem in thermoelastoestatics for a quadrant domain. Shiah
and Lee (2011) expressed the problem of 3D modeling of anisotropic heat conduction problem with
arbitrary volume heat source. In order for solving the problem, a Boundary Integral Equation and
Multiple Reciprocity Method were applied and three numerical examples were explained to demonstrate
the accuracy of the method. Baldasseroni et al. (2011) demonstrated heat transfer simulation accompanied
by thermal measurements of microfabricated x-ray transparent heater stages. An amorphous silicon
nitride membrane was introduced appropriate for the sample. Thermal specifications in air and vacuum
were analyzed, analytically and with simulation. Hoshan (2009) presented a triple integral equation
method for solving heat conduction equation. A new kind of triple integral was employed to find a
solution of non-stationary heat equation in an axisymmetric cylindrical coordinates under mixed
boundary of the first and second kind conditions, using Laplace transform the triple integral turned into a
singular integral of the second type. Cossali (2009) expressed an analytical solution of the steady periodic
heat conduction in a solid homogenous finite cylinder via Fourier transform, with the sole restriction of
uniformity on the lateral surface and radial symmetry on the bases. A harmonic heating, as an example,
introduced accompanied with simulation results. In (Lambrakos et al., 2008) inverse analysis of heat
conduction problem in hollow cylinder with axisymmetric source distribution was explained with
experimental results. Golytsina (2008) presented mathematical simulation of temperature field in a hollow
rotating cylinder with nonlinear boundary conditions. Volle et al. (2008) introduced a semi-analytical
method for inverse heat conduction of a rotating cylinder using integral transform methods.
In this paper, in order to solve the problem as an exact method, generalized finite Hankel transform is
used. Hankel transform is used for solving problems consist of cylindrical coordinates, but not the hollow
cylinders. Eldabe et al (2004) introduced an extension of the finite Hankel transform, which is capable of
solving hollow cylindrical coordinates, heat equation or wave with mixed boundary values. Povstenko
(2008) expressed the radial diffusion in a cylinder via Laplace and Hankel transform. Akhtar (2001)
presented exact solutions for rotational flow of a generalized Maxwell fluid between two circular
cylinders.
![Page 2: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/2.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
����
Modeling of the Axis Symmetric Problem
In this section, the distribution of temperature in a hollow cylinder is considered, as it is shown in figure
(1). The equation of the problem is in the form of equation (1):
tzz��2rrr
2 uuur
1u
r
1uc =�
�
���
�+++ (1)
Figure (1): Schematic of the hollow cylinder.
Since the case is not dependent onθ , equation (1) can be written as equation (2):
tzzrrr
2 uuur
1uc =�
�
���
�++ (2)
In which:
( )2
2
rrr
tz,r,uu
∂
∂=
( )r
tz,r,uu r
∂
∂=
( )2
2
zzz
tz,r,uu
∂
∂=
( )t
tz,r,uu t
∂
∂=
Where u is the temperature, z the height, r the radius of the cylinder. Also t stands for the time and
c for diffusivity factor. The boundary and initial condition are considered in equations (3-7):
( ) 0tz,a,u = (3)
( ) z
beTtz,b,u = (4)
( ) 0tr,0,u = (5)
( ) 0th,r,u = (6)
![Page 3: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/3.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
� ����
( ) 0tz,r,u = (7)
Where bT is a constant temperature. In order to solve the PDE equation, integral transformations are
used. The first transformation is Laplace which changes the domain of time to s , equation (8):
( )z,0r,uusuur
1uc zzrrr
2 −=��
���
�++ (8)
In which:
( ) ( ){ }tz,r,uLsz,r,u =
( )2
2
rrr
sz,r,uu
∂
∂=
( )r
sz,r,uu r
∂
∂=
( )2
2
zzz
sz,r,uu
∂
∂=
Second transformation is Fourier Cosine and therefore equation (8) changes to equation (9):
( ) ( ) ( ) ( )[ ] ( )sn,r,ussh,r,u1sr,0,u2sn,r,u�nur
1uc z
1n
z
22
rrr
2 =��
���
�−+−−+
+ (9)
Where:
( ) ( ) dzz)h
n�cos(sz,r,u
h
2sn,r,u
h
0�=
( )2
2
rrr
sn,r,uu
∂
∂=
( )r
sn,r,uu r
∂
∂=
The boundary conditions of the bottom and top of the cylinder appears in equation (9) which are zeroes.
Forming the equations as following:
( )( ) ( )sn,r,ucn�sur
1uc
2
rrr
2 +=��
���
�+ (10)
Finite Hankel transform can be applied. The general formulation is presented in equation (11) [9]:
( )( )
( )( )
( ) ( )nfkafakJ�a
bk2Jbf
�b
2
x
ml
dx
d
x
2l1
dx
dH 2
i
im
l
im
l2
22
2
2
m −−=�
��
−+
−+= (11)
Selecting l , m equal to zero in equation (11), the left side of equation (10) is appeared and employing
the transformation results the equation (12):
( )( )( )
( ) ( ) ( )( )ucn�ssn,,kuksn,a,uak�J
bk2Jsn,b,u
�
2c
2
i
2
i
i0
i02 +=���
����
�−− (12)
In which:
( ) ( ){ }sn,r,uHsn,,ku 0i =
Simplifying and applying the radial boundary conditions equation (12) turn into equation (13):
( )( ) ( ){ }
( )���
����
�
+
−+−
++=
22
n
b
2
i
2
2
i�n1
1e1
s
T
ckcn�s
1
�
4csn,,ku (13)
We separate equation (13) into two parts 0n = and 0n > . First, for 0n > , inverse finite Hankel
Transform is applied in equation (14):
![Page 4: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/4.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
����
( )( )
( ) ( ) ( ) ( ){ }( )
( ) ( ) ( ) ( )[ ]rkYbkJbkYrkJ�n1
1e1
s
T
ckcn�s
1
�
4c
bkJakJ
akJk
2
�sn,r,u
i0i0i0i022
n
b
2
i
2
2
i
2
0i
2
0
i
2
0
2
iinf
1i
2
−���
����
�
+
−+−×
++−=�
=
(14)
Taking inverse Fourier Cosine transform, equation (15) is formed:
( )( )
( ) ( ) ( ) ( ){ }( )
( ) ( ) ( ) ( )( ) ��
���
�−�
��
����
�
+
−+−×
++−=��
= =
zs
n�cosrkYbkJbkYrkJ
�n1
1e1
S
T
ckcn�s
1
�
4c
bkJakJ
akJk
2
�sz,r,u
i0i0i0i022
n
b
inf
1n2
i
2
2
i
2
0i
2
0
i
2
0
2
iinf
1i
2
(15)
Finally, inverse Laplace transform should be taken, equation (16):
( )( )
( ) ( ) ( ) ( ){ }( )
( ) ( ) ( ) ( )( ) ( ) ( ){ }( )tckcn�
i0i0i0i022
n
2
i
2
inf
1n i
2
0i
2
0
i
2
0
2
ib
inf
1i
2
2i
2
e1zh
n�cosrkYbkJbkYrkJ
�n1
1e1
ckcn�
1
bkJakJ
akJkT�2ctz,r,u
+−
= =
−×��
���
�−�
��
����
�
+
−+−×
+−=��
(16)
In order to solve in steady state solution, t is considered infinity, so equation (16) is written in the form of
equation (17):
( )( )
( ) ( ) ( ) ( ){ }( )
( ) ( ) ( ) ( )( ) ��
���
�−�
��
����
�
+
−+−×
+−=��
= =
zh
n�cosrkYbkJbkYrkJ
�n1
1e1
ckcn�
1
bkJakJ
akJkT�2czr,u
i0i0i0i022
n
2
i
2
inf
1n i
2
0i
2
0
i
2
0
2
ib
inf
1i
2
(17)
The second part, 0n = results equation (18):
( )( )
( )1es
T
cks
1
�
2c
2
s,0,ku b
2
i
2
i −+
= (18)
In addition, taking inverse Finite Hankel and Laplace transforms change equation (18) to (19):
( ) ( )( ) ( )
( )
( ) ( ) ( ) ( )[ ]( )
( )( )tck
2
i
i0i0i0i0
i
2
0i
2
0
i
2
0
2
iinf
1i
b
2
2ie1
ck
1rkYbkJbkYrkJ
1ebkJakJ
akJk�Tc
2
tr,0,u
−
=
−−×
−−
=� (19)
As steady-state analytical solution, equation (20) is appeared:
( ) ( )( ) ( )
( ) ( ) ( ) ( ) ( )( )rkYbkJbkYrkJ1ebkJakJ
akJ�T
2
rui0i0i0i0
i
2
0i
2
0
i
2
0inf
1i
b −−−
=�=
(20)
The final steady-state solution is both parts of answers in equation (21):
( )( )
( ) ( )( ) ( ) ( ) ( ) ( )[ ]
( )( ) ( ) ( ) ( ){ }
( )( ) ( ) ( ) ( )[ ] �
�
���
�−�
��
����
�
+
−+−×
+−+
−−−
=
��
�
= =
=
zh
n�cosrkYbkJbkYrkJ
�n1
1e1
ckcn�
1
bkJakJ
akJkT�2c
rkYbkJbkYrkJ1ebkJakJ
akJ�Tzr,u
i0i0i0i022
n
2
i
2
inf
1n i
2
0i
2
0
i
2
0
2
ib
inf
1i
2
i0i0i0i0
i
2
0i
2
0
i
2
0inf
1i
b
(21)
![Page 5: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/5.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
� ���
In order to simulate i
k should found by equation (22) [9]:
( ) ( ) ( ) ( ) 0bkYakJakYbkJ i0i0i0i0 =− (22)
In which 0.5a = , 1b = . In table (1) the roots of equation (22) are presented.
Table (1): Roots of the equation (22).
1k 6.24 11k 69.11 21k 131.94 31k 194.77 41k 257.60
2k 12.54 12k 75.39 22k 138.22 32k 201.06 42k 263.89
3k 18.83 13k 81.67 23k 144.51 33k 207.34 43k 270.17
4k 25.12 14k 87.96 24k 150.79 34k 213.62 44k 276.45
5k 31.40 15k 94.24 25k 157.07 35k 219.91 45k 282.74
6k 37.69 16k 100.52 26k 163.36 36k 226.19 46k 289.02
7k 43.97 17k 106.81 27k 169.64 37k 232.47 47k 295.30
8k 50.26 18k 113.09 28k 175.92 38k 238.75 48k 301.59
9k 56.54 19k 119.37 29k 182.21 39k 245.04 49k 307.87
10k 62.82 20k 125.66 30k 188.49 40k 251.32 50k 314.15
Considering C100Tb
�= , 10n = , 1c = , and 50i = at 0.5z = the distribution of temperature is
shown in figure (2). For a better presentation4
3 of the contour is displayed.
Figure (2): The distribution of temperature at 0.5z = .
In order to verify the results, Finite Element Method is used and the temperature field is demonstrated in
figure (3).
![Page 6: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/6.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
���
Figure (3): The distribution of temperature FEM.
The details of temperature field at 0.5z = is shown in figure (4) and at 1z = in figure (5).
Figure (4): The distribution of temperature at 0.5z = , Exact and FEM.
![Page 7: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/7.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
� ����
Figure (5): The distribution of temperature at 1z = , Exact and FEM.
Finally at 0.75r = and 1z0 << the comparison between methods is shown in figure (6).
Figure (6): The distribution of temperature at 0.75r = and 1z0 << .
Modeling of the General Problem
In previous section the distribution of temperature was solved as an axis symmetric case and because the
problem was independent of � , generalized finite Hankel transform of zero order was used. In this part
the problem and boundary conditions are dependent on � , so the PDE equation (1) is used and boundary
conditions are chosen as equations (23-27):
( ) 0tz,�,a,u = (23)
( ) z
b e�Ttz,�,b,u = (24)
( ) 0t�,0,r,u = (25)
( ) 0th,�,r,u = (26)
( ) 0z,0�,r,u = (27)
Applying the Laplace transformation, equation (1) changes to equation (28):
( )z,0�,r,uusuur
1u
r
1uc zz��2rrr
2 −=��
���
�+++ (28)
![Page 8: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/8.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
����
Next step, finite Fourier Cosine transform is employed, so the equation turns into equation (29):
( ) ( ) ( ) ( )[ ]
( )sn,�,r,us
sh,�,r,u1s�,0,r,u2sn,�,r,u�nur
1u
r
1uc z
1n
z
22
��2rrr
2
=
��
���
�−+−−++
+
(29)
Boundary conditions at the bottom and the top of the cylinder are zero so the simplified equation is
appeared as equation (30):
( ) ( )sn,�,r,ussn,�,r,u�nur
1u
r
1uc 22
��2rrr
2 =��
���
�−++ (30)
Taking Periodic Fourier transformation and simplify the equation result:
( )( ) ( )sn,m,r,u~cn�su~
r
mu~
r
1u~c
2
2
2
rrr
2 +=���
����
�−+ (31)
In which:
( ) ( )�−−=
�
�
im�d�esn,�,r,usn,m,r,u~
( )2
2
rrr
sn,�,r,uu~
∂
∂=
( )r
sn,�,r,uu~r
∂
∂=
Considering l equal to zero in equation (11) and applying Hankel Transform the solution forms as
equation (32):
( )( )
( ) ( )2
i
2
2
ickcn�s
sn,m,b,u~
�
2csn,m,,ku
++= (32)
In which:
( )( ) ( )
���
����
� −���
����
�
+
−+−=
m
12I�
�n1
1e1
s
2Tsn,m,b,u~
m
22
n
b
Equation (32) is considered in two parts: 0n = and 0n > . For the first case taking inverse Hankel
transform results equation (33):
( )( )
( ) ( ) ( ) ( ){ }( ) ( )
( ) ( ) ( ) ( )[ ]rkYbkJbkYrkJm
12I�
�n1
1e1
s
2T
ckcn�s
1
�
2c
bkJakJ
akJk
2
�sn,m,r,u~
imimimim
m
22
n
b
2
i
2
2
i
2
mi
2
m
i
2
m
2
iinf
1i
2
−×���
����
� −���
����
�
+
−+−×
++−=�
=
(33)
Using inverse Laplace, Periodic Fourier and Cosine Fourier transforms equation (33) changes to equation
(34):
( )
( )( ) ( ) ( ) ( )
( ) ( )
( ) ( ) ( ) ( )[ ] ( ) ( ) ( ){ }( )tckcn�im�
imimimim
m
22
ninf
1n
infm
infm2
i
2
i
2
mi
2
m
i
2
m
2
iinf
1i
b
2
2i
2
e1zn�coserkYbkJbkYrkJ
m
12I�
�n1
1e1
ckcn�
1
bkJakJ
akJkTc
tz,�,r,u
+−
=
=
−= =
−−×
���
����
� −���
����
�
+
−+−
+−
=
� � � (34)
Moreover, the steady state answer is, equation (35):
![Page 9: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/9.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
� ����
( )
( )( ) ( ) ( ) ( )
( ) ( )
( ) ( ) ( ) ( )[ ] ( )zn�coserkYbkJbkYrkJ
m
12I�
�n1
1e1
ckcn�
1
bkJakJ
akJTkc
z�,r,u
im�
imimimim
m
22
ninf
1n
infm
infm
inf
1i2
i
2
i
2
mi
2
m
i
2
mb
2
i
2
−×
���
����
� −���
����
�
+
−+−
+−
=
� � �=
=
−= =
(35)
Also the solution of the second part is, equation (36):
( ) ( )( ) ( ) ( ) ( )
( )( ) ( )
( ) ( ) ( ) ( )[ ] im�
imimimim
m
tckinfm
infm
inf
1i2
i
2
i
2
mi
2
m
i
2
mb
erkYbkJbkYrkJ
m
12I�e1
ckcn�
1
bkJakJ
akJ
2
T
2
t�,0,r,u 2i
−×
���
����
� −−
+−= −
=
−= =
� � (36)
And the steady state answer for this part is, equation (37):
( ) ( )( ) ( ) ( ) ( )
( )( )
( ) ( ) ( ) ( )[ ] im�
imimimim
minfm
infm
inf
1i2
i
2
i
2
mi
2
m
i
2
mb
erkYbkJbkYrkJ
m
12I�1e
ckcn�
1
bkJakJ
akJ
2
T
2
�,0r,u
−×
���
����
� −−
+−= � �
=
−= = (37)
Finally, the analytical answer for steady-state situation is presented in equation (38):
( )
( )( ) ( ) ( ) ( )
( )( )
( ) ( ) ( ) ( )[ ]
( )( ) ( ) ( ) ( )
( ) ( )
( ) ( ) ( ) ( )[ ] ( )zn�coserkYbkJbkYrkJ
m
12I�
�n1
1e1
ckcn�
1
bkJakJ
akJTkc
erkYbkJbkYrkJ
m
12I�1e
ckcn�
1
bkJakJ
akJ
2
T
z�,r,u
im�
imimimim
m
22
ninf
1n
infm
infm
inf
1i2
i
2
i
2
mi
2
m
i
2
mb
2
i
2
im�
imimimim
minfm
infm
inf
1i2
i
2
i
2
mi
2
m
i
2
mb
−×
���
����
� −���
����
�
+
−+−
+−+
−×
���
����
� −−
+−
=
� � �
� �
=
=
−= =
=
−= =
(38)
In order for simulating ik should found by equation (39) [9]:
( ) ( ) ( ) ( ) 0bkYakJakYbkJ imimimim =− (39)
In which 0.5a = , 1b = and 10m10 ≤≤− . In table (2) the roots of equation (39) are presented.
Table (2): Roots of the equation (40).
m -10,10 -9.9 -8,8 -7,7 -6,6 -5,5 -4,4 -3,3 -2,2 -1,1 0
1k 14.5 13.40 12.31 11.23 10.18 9.19 8.26 7.45 6.81 6.93 6.24
2k 18.82 17.80 16.84 15.93 15.10 14.37 13.74 13.23 12.85 12.62 12.54
3k 23.57 22.74 21.97 21.27 20.65 20.11 19.66 19.30 19.04 18.88 18.83
4k 28.84 28.17 27.55 27.00 26.51 26.09 25.74 25.47 25.28 25.16 25.12
5k 34.45 33.89 33.38 32.93 32.53 32.19 31.91 31.69 31.53 31.43 31.40
6k 40.26 39.78 39.35 38.97 38.63 38.34 38.11 37.93 37.79 37.71 37.69
7k 46.2 45.78 45.40 45.07 44.78 44.54 44.33 44.18 44.06 44.00 43.97
8k 52.4 51.84 51.51 51.22 50.97 50.75 50.57 50.43 50.33 50.28 50.26
9k 58.28 57.96 57.66 57.40 57.17 56.98 56.82 56.70 56.61 56.56 56.54
10k 64.40 69.40 63.83 63.60 63.39 63.22 63.08 62.97 62.89 62.84 62.82
![Page 10: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/10.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
����
Considering C100Tb
�= and 1c = , simulation results are obtained. In figure (7), the temperature field is
shown and as it was expected; in this case, temperature is dependent on � and with increasing that,
temperature is enlarged. Temperature at ��,� −= has different signs so there is a jump at this point.
Roughness of the figure is caused by selecting small range for i , m , n . If these values are chosen in a
wide range, the result will be smoother.
Figure (7): The temperature field at 0.5z = .
In order to verify the solution, finite element method is used and results the figure (8), the distribution of
temperature at 0.5z = and 2
�� = .
Figure (8): The temperature field at 0.5z = and 2
�� = .
![Page 11: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/11.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
� ����
And in figure (9) the variation of temperature at 0.75r = and2
�� = is presented. The verification is not
as precisely as axis symmetric case and the reason is choosing the range of 10m10 ≤≤− .
Figure (9): The temperature field at 0.75r = and2
�� = .
Conclusion
In this paper, the heat conduction of a hollow cylinder was discussed and solved as an exact solution
method. Using Generalized Finite Hankel Transform is systematic, simple and reliable as it was shown in
verifications with Finite Element Method. Two situations, axis symmetric and general case, were
explained and simulated. Finally, the results show that this method is suitable for solving PDE equations
in cylindrical coordinates.
References
Akhtar W, Siddique I, Sohail A (2011) Exact Solutions for the Rotational Flow of a Generalized Maxwell
Fluid Between two Circular Cylinders. Commun Nonlinear SciNumer Simulat 16: 2788-2795
Baldasseroni C, Queen D R, Cooke D W, Maize K, Shakouri A (2011) Heat Transfer Simulation and
Thermal Measurements of Microfabricated x-ray Transparent Heater Stages. Review of Scientific
Instruments 82(9):093904
Cossali G E (2009) Periodic Heat Conduction in a Solid Homogeneous Finite Cylinder. International
Journal of Thermal Sciences 48: 722-732
Eldabe N T, El-Shahed M, Shawkey M (2004) An Extension of the Finite Hankel Transform. Applied
Mathematics and Computation 151: 713-717
Golitsyna E V (2008) Mathematical Simulation of Temperature Field in a Hollow Rotating Cylinder with
Nonlinear Boundary Conditions. Pleiades Publishing, High Temperature 46(6): 835-84
Hoshan N A (2009) The Triple Integral Equations Method for Solving Heat Conduction Equation. Journal
of Engineering, Thermophysics 18(3): 258-262
Lambrakos S G, Michopoulos J G, Jones H N, Boyer C N (2008) Inverse Analysis of Heat Conduction in
Hollow Cylinders with Asymmetric Source Distributions. Journal of Materials Engineering and
Performance 17: 651-661
Povstenko Y Z (2008) Fractional Radial Diffusion in a Cylinder. Journal of Molecular Liquids 137: 46-50
Sermet V (2012) New Closed-form Green Function and Integral Formula for a Thermoelastic Quadrant.
Applied Mathematical Modeling 36: 799-812
Shiah Y C, Lee R F (2011) Boundary Element Modeling of 3D Anisotropic Heat ConductionInvolving
Arbitrary Volume Heat Source. Mathematical and Computer Modeling 54:2392-2402
![Page 12: Heat Conduction of a Hollow Cylinder via Generalized ... · PDF fileInternational Research Journal of Applied and Basic ... the heat conduction problem of a ... solution of non-stationary](https://reader034.fdocuments.net/reader034/viewer/2022052515/5a79ddc07f8b9a5c3a8d83f3/html5/thumbnails/12.jpg)
Intl. Res. J. Appl. Basic. Sci. Vol., 3 (4), 758-769, 2012
�
����
Volle F, Maillet D, Gradeck M, Lebouche M (2008) Semi-analytical inverse heat conduction on a rotating
cylinder with Laplace and Fourier transforms. Inverse Problems in Science and Engineering 16(5):
655-674