HAYSSENSANDIACRE - SolidWorks › casestudies_chs › pdf › Hayssensandiacre_CHS1.pdfSolidWorks...
Transcript of HAYSSENSANDIACRE - SolidWorks › casestudies_chs › pdf › Hayssensandiacre_CHS1.pdfSolidWorks...
HayssenSandiacre Barry Wehmiller Herman Hayssen 1910
(FFS) 10000 HayssenSandiacre
HayssenSandiacre FFS Ultima® 130
HayssenSandiacre
Nick Caggiano 300 400
HayssenSandiacre Adobe ® FrameMaker® Caggiano
Caggiano Barry Wehmiller SolidWorks® Composer
HAYSSENSANDIACRE SolidWorks Composer
利用 S o l i d W o r k s C o m p o s e r 软件,HayssenSandiacre 可以直接从 3D CAD 模型创建文档影像,加快文档的开发速度。
难题:
解决方案:
SolidWorks Composer 3D CAD
成效:
• 52%• 30% 40%• •
单击这里查看一段演示如何在 Ultima SV 机器上更换切削刀片
的动画,该动画使用 SolidWorks Composer 创建。
不再迷失于翻译之中HayssenSandiacre SolidWorks Composer Ultima SV FFS
Caggiano SolidWorks Composer SolidWorks CAD
SolidWorks Composer Caggiano
52% Phyllis Millard
毫无耽搁的文档编制Caggiano SolidWorks Composer
SolidWorks Composer Caggiano
SolidWorks
Caggiano SolidWorks Composer
30% 40% ”
更灵活的材料,更高的效率 SolidWorks Composer HayssenSandiacre
SolidWorks Composer Caggiano SolidWorks Composer SolidWorks Composer
20 30
SolidWorks Dassault Systèmes SolidWorks Corporation / ©2013 Dassault Systèmes. MKHAYCSCHS0213
“使用 SOLIDWORKS COmpOSeR 之后,我们能够实现用视觉化内容取代冗长的文字说明这一目标,包括一整段流程动画。新的说明书更加容易理解,制作起来也更加快捷,而且减少了所需的翻译量。”
Nick Caggiano
HayssenSandiacre225 Spartangreen Blvd.Duncan SC 29334 USA
1 864 486 4000www.hayssensandiacre.com
TriMech Solutions Charlotte NC USA
U l t i m a ® X X 9-1/Rev 6HAYSSENSANDIACRE®
9
KNIFE ASSEMBLY
The knife is housed in the front jaw assembly. Operating in an orbital motion, it swings out of a recess in the front jaw, cuts through the film, and passes into a recess in the rear jaw. At the end of the dwell time, the knife retracts back into the front jaw.
Knife Blade Replacement
To remove and reinstall the knife blade, perform the steps outlined in the following diagrams depicting the jaw assembly.
WARNING:Use caution when working in the knife area. The knife edge is extremely sharp and cuts even when brushed against.
WARNING:• Always REMOVE power and air from the machine
before performing the knife blade replacement proce-dure.
• Use appropriate lockout/tagout procedures.
1. 2.
3. 4.
U l t i m a ® X X 9-1/Rev 6HAYSSENSANDIACRE®
9
KNIFE ASSEMBLY
The knife is housed in the front jaw assembly. Operating in an orbital motion, it swings out of a recess in the front jaw, cuts through the film, and passes into a recess in the rear jaw. At the end of the dwell time, the knife retracts back into the front jaw.
Knife Blade Replacement
1. Remove machine power and air.Use appropriate lockout/tagout procedures.
2. Pull front jaw carrier toward the front of the machine.3. Lift the right side knife retainer from the pin4. Swing the knife retainer to the side.5. Lift the left side knife retainer from the pin.6. Swing the knife retainer to the side.
WARNING:Use caution when working in the knife area. The knife edge is extremely sharp and cuts even when brushed against.
1 = Knife Retainer 6 = Flow Control2 = Knife 7 = Knife Air Cylinder3 = Rear Jaw 8 = Jam Nut4 = Knife Linkage 9 = Rod End
5 = Front Jaw
CAUTION:Use caution when working with the knife, as it is very sharp and may be very hot.
21 3
45
67
8
96
使用 SolidWorks Composer 之前
使用 SolidWorks Composer 之后
SolidWorks Composer HayssenSandiacre
Dassault Systèmes SolidWorks Corporation175 Wyman Street Waltham, MA 02451 USA
www.solidworks.com.cn
+65 6511 [email protected]