Hayneedle | Shop Furniture, Home Decor & Outdoor …- In storing patio furniture, do not stack...
Transcript of Hayneedle | Shop Furniture, Home Decor & Outdoor …- In storing patio furniture, do not stack...
ITEM NAME:Coral Coast Sanders Steel Mesh Outdoor Chaise Lounge
SKU:NINB007-1
For assistance with assembly, please contact customer service email us at [email protected] or toll free at:
1-888-880-4884
1/6
#A #B
Armrest Qty:2 Qty:2
#C #D
Qty:1 Qty:2
#E #F
Chair Frame Qty:1 Leg Qty:1
PANEL AND FITTINGS IDENTIFICATION:
PRE-ASSEMBLY PREPARATION:
DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
Crossbar
Wheel axle Wheel
!
2/6
25.9
24.96
IMPORTANT: PLEASE READ INSTRUCTIONS BEFORE ASSEMBLY - Identify all parts prior to assembly against the part list. - Remove all packaging and place parts on a non-abrasive surface to avoid scratching. - If any parts are missing or damaged DO NOT ATTEMPT TO ASSEMBLE, please contact the customer service center. - Keep small parts and pieces away from children until fully assembled. - Please check for any loose bolts and tighten them before you use.
TO AVOID DAMAGE TO YOUR FURNITURE. - In storing patio furniture, do not stack anything on glass, stone or marble tabletops. - If not drained properly, water can cause freeze damage. - Cover furniture with outdoor furniture covers when not in use.
#G #H #I
Bolt Qty:8 Bolt Qty:4
(M6x40) (M6x20)
#N #O #K
Tube Insert Qty:4 Axle Insert Qty:2 Bolt Cover Qty:12
#L #J #M
Bolt Qty:2
Metal Washer (M6)
(for wheel axle)
HARDWARE LIST:
Allen Wrench Qty:1
Metal Washer Qty:2
3/6
STEP-BY-STEP ASSEMBLY:
STEP 1: Place the parts on a non-abrasive surface.
a. Attach the wheel axle (C) to the two axle inserts (O).
b. Insert the wheel axle between the two armrests (A). Fasten the two wheels (D) to the
wheel axle using two bolts (L) and metal washers (J). See illustration. Tighten the bolts
using the Allen wrench (G).
c. Attach the four tube inserts (N) to the ends of the crossbars (B).
d. Insert the crossbars between the two armrests (A) and secure using four bolts M6x40 (H)
and metal washers (M). Tighten the bolts using the Allen wrench (G). Cover the bolts with
the plastic bolt covers (K).
STEP 2:
Attach the chair leg (F) to the chair frame (E) using four bolts M6x20 (I). Cover all bolts with
the plastic bolt covers (K).
1
2
4/6
STEP 3:Secure the chair frame to the armrests using four bolts M6x40 (H) and metal
washers (M).
Tighten the bolts using the Allen wrench (G). Cover the bolts with the plastic bolt covers (K).
STEP 4: Completed assembly.
3
4
5/6
Part descriptions Parts image QTY
A 2
B 2
C 1
D 2
E 1
F 1
G 1
H 8
I 4
J 2
K 12
L 2
M 8
N 4
O 2
Tube Insert
Axle Insert
Plastic Bolt Cover
M8x100mm Bolt
Metal Washer (M6)
M6x40mm Bolt
M6x20mm Bolt
Metal Washer
(for wheel axle)
Armrest
Crossbar
Wheel axle
Wheel
Frame
Leg
Allen Wrench
6/6