Copyright(C)2006 Embroidery Central, Inc. Page 1 of 6

Halloween Free StandingLace CharmsCreate your own jewelry and Halloween Tree with theHalloween Charm Free Standing Lace embroiderydesigns.

STEP: 1

Here is a list of supplies we used for each project.Embroidery Design Materials: Lace HalloweenCharm Design(s), Water Soluble Stabilizer such asAquaFilm Badgemaster, Thread & Bobbin Thread(same color), Sharp 11 Needle, Paper Towels, Bowl& Water. Necklace Materials: Necklace clasps,Transparent necklace cord, Jewelry glue, Needle nosepliers, Beads, Ruler, Scissors. Earring Materials: 3/4"Fishhook Earrings, 4mm Jump Rings, Needle NosePliers. Ornament Materials: Ornament Hooks.

STEP: 2Embroider your Lace Halloween Charms first. Cut apiece of Badgemaster that is a little larger than yourhoop.

Copyright(C)2006 Embroidery Central, Inc. Page 2 of 6

STEP: 3

Hoop Badgemaster, making sure that it is hoopedvery tightly.

STEP: 4

Place hoop onto your machine and embroider the lacedesign(s) of your choice.

STEP: 5

Once the design is done embroidering, remove fromthe machine and trim the excess Badgemaster aroundthe outside of the design.

STEP: 6

Add hot/warm water to your container. The watershould be high enough in the bowl so that the entirelace heart will be submerged. Place your lace designinside the container. Let the design soak as directed.This will remove the stabilizer from the design.Remove the design from the water and place on papertowel to dry; making sure that it is flat.

Copyright(C)2006 Embroidery Central, Inc. Page 3 of 6

STEP: 7

Make your Halloween Earrings next. Gather yoursupplies to make the earring.

STEP: 8

Use your pliers to slightly open one 4 mm jump ring.

STEP: 9

Place the design onto the ring.

STEP: 10

Place the fishhook earring onto the ring also.

Copyright(C)2006 Embroidery Central, Inc. Page 4 of 6

STEP: 11

The earring is complete.

STEP: 12

Next, make your Halloween Necklace. There are alot of wonderful jewelry supplies available, so be ascreative as you want with your necklace.

STEP: 13What we did first was to measure an existingnecklace and cut the plastic necklace about 2" longer.

STEP: 14

Place the necklace clasp onto the necklace near oneend and tie it off with a couple of knots.

Copyright(C)2006 Embroidery Central, Inc. Page 5 of 6

STEP: 15

Now you will want to plan how you want yournecklace to look. We suggest laying out the beads andother items in order of how they will go on thenecklace. Now add them to your necklace along withyour lace embroidery design.

STEP: 16

Now that you have the beads on your necklace attachthe other side of the clasp and tie it on. Close theclasp. Now stretch out the necklace and tape the claspdown to your table and tape the embroidery designdown, pulling the necklace tight.

STEP: 17

With a ruler beside the necklace position the beadswhere you would like them. You can use the ruler tomake sure that the beads are in the same position onboth sides.

STEP: 18

Use your jewelry glue to secure a bead on each sideof the embroidery design to keep it in place. Thenglue each bead to the necklace on each side. Afteryou have completed this step let the glue dryaccording to the instructions on the package.

Copyright(C)2006 Embroidery Central, Inc. Page 6 of 6

STEP: 19

Your necklace is complete.

STEP: 20

You can purchase Halloween Trees at most craftstores or you can make your own. Decorate asdesired.