Halfshell Mount Installation - PVP Communications Hea… · Installation Types WARNINGS: •...
Transcript of Halfshell Mount Installation - PVP Communications Hea… · Installation Types WARNINGS: •...
Halfshell Mount Installation
1. Pull chin strap buckle
through rubber flap.
Completed installation
7. Carefully dress any wiring
with wooden stick as shown.
6. Mount Headset.
NOTE: Snaps are directional
Install by engaging the align-
ment tab in the headset snap
first (as shown).
4. Install a snap base over the
post. Use the die and punch
set to lock base to post.
5. Repeat for remaining snap
positions.
3. Push a snap post through
the gap created in step 2
2. Locate snap positions and
press a pointed object (i.e. the
tip of a pen) through webbing.
NOTE: Only separate the
webbing, do not cut it.
TAB
TAB
NOTE: Reverse this process
to dis-engage snaps. (lift side
opposite the tab first)
-8-
OPERATIONAL NOTE The microphone used in this helmet kit is VERY position sensitive. Output
volume will decrease significantly if mic is not placed squarely (properly
rotated), and within 1/4” of the users mouth. Use the swivel mount tensioning
nut to set proper positioning, and use the windscreen provided for best results
in rejecting wind noise.
Helmet Headsets
United States Patent No.
6,311,052 & 7,062,301
INSTALLATION
INSTRUCTIONS
2310 W 205th Street
Torrance, California 90501
(800)584-4119
www.pvpcom.com
Thank you for choosing PVP Communications, Inc. products. We are dedicated
to satisfying our customers by providing quality products and service. The
components in this Kit are tailored for use in applications where durability,
strength and quick installation are a must.
Please follow the Installation Instructions carefully to avoid damaging radio
equipment or Kit components. If you have any questions during installation or
require more information about this product you may call us at (310)212-5432
Monday through Friday, 7AM to 4PM Pacific Time, USA.
WARRANTY
This product comes with a warranty covering all defects in material or
workmanship for a period of one year from date of original retail purchase. At
its option PVP Communications, Inc. will repair or replace any defective part(s)
or equipment. The provisions of the warranty shall not apply to any unit which
has been subjected to misuse, neglect, incorrect electrical or mechanical
installation, unauthorized modifications, accident, nor to units which have been
repaired or altered outside of PVP Communications, Inc.. The warranty is extended only to the original owner of the PVP Communications, Inc. product
and may not be transferred or assigned. In the event that the product does not
conform to the warranty, the product should be shipped prepaid to PVP
Communications, Inc.. Transportation charges, insurance fees, and labor costs
for shipment, removal, or reinstallation of product are not covered by this
warranty. Loss or damage in shipment is the sole responsibility of the freight
carrier. Repair as provided under this warranty is the exclusive remedy of the
consumer. PVP Communications, Inc. shall not be liable for any incidental or
consequential damages or for breach of any express or implied warranty on this
product. Except to the extent prohibited by applicable law, any implied
warranty of merchantability, or fitness for a particular purpose on this product is limited in duration to the duration of the warranty. Some states do not allow
the exclusion or limitation of incidental or consequential damages, or allow
limitations on how long an implied warranty lasts, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights
which vary from state to state. PVP Communications, Inc. reserves the right to
make changes in design and to make improvements in its products without the
obligation to incorporate the changes or improvements in any of its previously
manufactured products. PVP Communications, Inc. has not authorized anyone
to make representations or warranties other than the warranty contained
herein. The above warranty is effective for all products manufactured after
01/01/95.
-2-
-7-
4) Tuck wire leads into gap between
the helmet and the foam core.
5) Install velcro and place left ear-
phone as shown.
8) Using the wooden stick, continue
to tuck the long earphone lead around
the rear rim of the helmet & into
opposing ear pocket.
9) Secure earphone with velcro.
10) Re-install cheek pads & ear
cushions.
11) Mount windscreen on mic.
7) Mate the microphone leads.
Interior Mount Installation
6) Clamp boom mic to interior.
(typical Arai Helmet install shown)
NOTE: Set clamps so as to dress mic
against the shell of the helmet. This
will keep the mic from pushing into
the cheekpads.
NOTE: Adjust boom length to place
the voice port at the user’s mouth.
NOTE: Rotate boom in the clamp to
orient voice port so that it does not
aim upward or downward, but is
directly aimed to the user’s mouth.
FINISHED INSTALL
-Voice port oriented to point directly
at the user’s mouth.
-Boom length adjusted to place the
mic at the user’s mouth.
-Clamps oriented to not push against
the cheekpads.
OPERATIONAL NOTE:
The mic used in this kit is very
position sensitive. Output volume
will decrease significantly if not
placed squarely (properly rotated),
and within 1/4” of the users mouth.
Proper positioning, and use of the
windscreen is critical in rejecting
wind noise.
Interior Mount Installation
1) Remove both left and right cheek
pads and ear cushions.
2) At the left side of the helmet, lay
the helmet harness pigtail as shown
with the pigtail plug dressed to the
exterior of the helmet. Cinch loosely
to helmet chin strap buckle as shown
with the two tie wraps.
NOTE: When headset is used with
Speakermics worn at the center of
the uniform, install harness to exit
at the right side of the helmet.
3) Adjust to desired pigtail exit
length at the outside of the helmet
and tightly cinch the tie wraps. Cut
off excess tie.
NOTE: When headset is used with
a mating Speakermic, set pigtail
cable exit length as shown below to
allow coils to dress at a right angle
without tension when worn.
EXAMPLE—Right side cable exit
with properly dressed pigtail coils.
Dress left side pigtails shorter for
speakermics worn at the left shoulder
-6-
Installation Types
WARNINGS:
• Long-term exposure to loud transmissions may cause hearing damage. It is
best to avoid high volume levels when using headphones, especially for
extended periods.
• Use caution when using your headset/headphones while operating a
vehicle or engaging in any activity that requires
your full attention. Check and follow local laws regarding mobile phone and
headset/headphones use. Some jurisdictions
impose specific limitations, such as single earpiece configuration, on the use
of such products while driving or riding.
INTERIOR
MOUNT
HEADSETS
(See page 6-7)
HALFSHELL
MOUNT
HEADSETS
(See page 8)
EXTERIOR
MOUNT
HEADSETS
(See page 4-5)
-3-
Exterior Mount Installation
1) Remove both left and right cheek
pads and ear cushions.
2) Remove microphone mounting
plate with Phillips screwdriver.
3) At the left side of the helmet, lay
the helmet harness pigtail as shown
with the pigtail plug dressed to the
exterior of the helmet. Cinch loosely
to helmet chin strap buckle as shown
with the two tie wraps.
NOTE: When headset is used with
Speakermics worn at the center of
the uniform, install harness to exit
at the right side of the helmet.
4) Adjust to desired pigtail exit
length at the outside of the helmet
and tightly cinch the tie wraps. Cut
off excess tie.
NOTE: When headset is used with
a mating Speakermic, set pigtail
cable exit length as shown below to
allow coils to dress at a right angle
without tension when worn.
EXAMPLE—Right side cable exit
with properly dressed pigtail coils.
Dress left side pigtails shorter for
speakermics worn at the left shoulder
5) Tuck wire leads into gap between
the helmet and the foam core.
-4-
6) Install velcro and place left ear-
phone as shown.
8) Insert mic cable into larger hole.
IMPORTANT:
Clean the exterior surface between
mounting holes in the helmet with the
alcohol pad provided, then
7) Peel tape from mic assembly. 12) Using the wooden stick, continue
to tuck the long earphone lead around
the rear rim of the helmet & into
opposing ear pocket.
13) Secure earphone with velcro.
14) Re-install cheekpads & ear
cushions.
15) Mount windscreen on mic.
11) Mate the microphone leads.
10) Install screw, lock-washer, and
washer using Philips screwdriver.
Exterior Mount Installation
-5-
OPERATIONAL NOTE:
The mic used in this kit is very
position sensitive. Output volume
will decrease significantly if not
placed squarely (properly rotated),
and within 1/4” of the users mouth.
Proper positioning, and use of the
windscreen is critical in rejecting
wind noise.
9) Pivot mic clip into large hole.
NOTE: Align smaller hole carefully
since tape will immediately adhere.