H500 Bluetooth Fone

8/6/2019 H500 Bluetooth Fone

1/20

1 - CHARGE2 - START

BLUETOOTHFEATURE

3 - PAIR4 - TEST AND USE

Get Connected in4 Quick Steps

H500Bluetooth

Handsfree Headset

Start Here > > >


2/20

BEFORE YOUBEGIN

Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions.

Earhook

Take a moment before you get started tofamiliarize yourself with your newH500 Handsfree Headset.

Volume

Buttons

BlueIndicator

Light

Call Button

Microphone


3/20

1

Charge your headset's battery for 2 hours:

Plug the Motorola charger into the end ofthe headset.

The blue indicator light turns on when the

battery is charging. It may take up to 1minute for the light to turn on. When theheadset's battery is fully charged (about 2hours), the blue indicator light turns off.

Unplug the charger from the headset.

1

2

CHARGEYour Headset's Battery

Note: Headset is not functional while charging.


4/20

START BLUETOOTHFeature

On Your Phone

2

Select ( Menu) > Settings > Connection >Bluetooth Link > Setup.

Scroll to Power.

Press Change.

Scroll to On.

Press Select to turn on the Bluetoothfeature. Bluetooth feature remains on until

you turn it off.

1

2

3

4

5

M

Your phone's Bluetooth feature is off bydefault. To use your headset, turn on theBluetooth feature in your phone.

For most Motorola phones:

Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.


5/20

TROUBLESHOOTING

My phone does not find my headset.Make sure the blue light on your headset issteadily lit when your phone is searching fordevices (see step 3).

My headset worked before but now it'snot working.Make sure your phone is on and theBluetooth feature is turned on in your phone(see step 2). If the Bluetooth feature has

been turned off or was turned on onlytemporarily, you may need to restart theBluetooth feature (see step 2). If you haveconfirmed the Bluetooth feature is on in yourphone, pair your phone and headset again

(see step 3).Support .If you need more help, contact us at1-877-MOTOBLU or visit us at

www.hellomoto.com/bluetooth and clickSupport.


6/20

MOTOROLA and the Stylized M Logo are registered in the USPatent & Trademark Office. The use of wireless devices and theiraccessories may be prohibited or restricted in certain areas.Always obey the laws and regulations on the use of theseproducts. The Bluetooth trademarks are owned by theirproprietor and used by Motorola, Inc. under license. All otherproduct or service names are the property of their respectiveowners.

Motorola, Inc. 2006.

Motorola, Inc.Consumer Advocacy Office1307 East Algonquin RoadSchaumburg, IL 60196

www.hellomoto.com1-877-MOTOBLU1-888-390-6456 (TTY/TDD United States forhearing impaired)

Guide Number: 6809494A56-C


7/20

PAIRYour Headset3

Call Button

With the headset power off, press and holdthe Call button for 6 to 10 seconds until theblue indicator light turns on and remainssteadily lit. (The light will flash while youhold the Call button.)

If the indicator light is flashing or does notremain steadily lit, turn off the headset and

repeat step 1.

1

2

Before you can use your headset, you mustpair (link) it with your phone.

Step A - PUT HEADSET IN PAIRING MODE

Blue Indicator Light

Note: To turn off headset, see "Turning On and Off" on the reverse side of this guide.


8/20

PAIRYour Phone

Select ( Menu) > Settings > Connection >Bluetooth Link > Handsfree > Look for Dev

The phone lists all Bluetooth devices it finds.Select Motorola H500.

Press OK or Yes to pair (link) the handsfreedevice.Enter the passkey 0000 and press OK.Note: Passkey cannot be changedfrom 0000.

Step B - SET THE PHONE TO LOOK FORYOUR HEADSET

3

4

1

2

M

When your headset is successfully paired withyour phone, the blue indicator light changes

from steadily lit to flashing.Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.

For most Motorola phones:


9/20

Your phone and headset are now paired andready to make and receive calls. To confirmthey are operating properly, make a call:

TEST AND USE

Place the headset over your ear. See"Wearing the Headset" on the reverse sideof this guide.

On your phone, dial the number you wantto call and press the Sendkey.

If your phone and headset are successfullypaired, you will hear ringing on the headset.

4

1

2

3

After you have successfully paired your phoneand headset, you do not need to repeat theseinitial setup steps each time you use the

headset.


10/20

USING YOUR H500

See Features and Functions Guideon the reverse side

of this guidefor information onusing your H500.


11/20

IMPORTANT:Be sure to first follow the

Quick Start Guideon the reverse side

of this guideto complete initial setupof your H500.

Features andFunctions Guide

H500

BluetoothHandsfree Headset


12/20

CallButton

To turn your headset on , press and hold theCall button until the indicator light flashes.Then, release the button.

Note: Headset may take up to 4 to 5 seconds to turn on.

To turn your headset off , press and holdthe Call button until the indicator light flashesrapidly and then turns off.

TURNING HEADSETON/OFF


13/20

3

4

WEARING THE

HEADSETOpen the earhook.Loop the earhook over your ear.

Press the headset to your ear.

1

2

3


14/20

CHANGING FOR USEON OTHER EAR

Open the earhook 90degrees from theheadset.

Gently lift and pull thetop of the earhook upand off the upper hingepin. Then, pull it away toremove it.

Flip the headset over.

Hook the bottom of theearhook onto the lowerhinge pin, then lift and pullthe top of the earhook overthe upper hinge pin.

1

2

3

4

You can wear your H500 headset on your left orright ear. The headset comes ready for the rightear. To change the headset for the left ear:

040059o

2 Pull Earhook Up

Hinge Pin

1 Open Earhook


15/20

CHANGING VOLUMEBUTTON ORIENTATION

If you change your headset to wear on theother ear, you can also change theorientation of the volume buttons.

Turn the headset power off.

Press the Call button and the volumebutton you want to assign as the"volume up" button until the indicatorlight flashes twice.

The headset power turns on.

1

2

Call Button

Volume Buttons


16/20

The essential requirements andother relevant provisions of Directive1999/5/EC.

All other relevant EU Directives.

European Union DirectivesConformance Statement

0168 ProductApprovalNumberThe above gives an example of a typical ProductApproval Number.

You can view your products Declaration of Conformity(DoC) to Directive 1999/5/EC (to R&TTE Directive) atwww.motorola.com/rtte. To find your DoC, enter theproduct Approval Number from your products label inthe Search bar on the web site.

Hereby, Motorola declares that thisproduct is in compliance with:


17/20

MAKING CALLS

Note: Your H500 supports both Handsfree and Headset Profiles. Accessing call functions depends upon whichprofile your phone supports. See your phone's user's guide for more information.

Function Action

Make a voice dial call Tap the Call buttonand speak thename after the tone

End a call Tap the Call button

Receive a call Tap the Call button

Reject a call Press and hold the

Call button until youhear a beep

Redial last call Press and hold theCall button until youhear a beep

Answer a second Press and hold theincoming call Call button (places

first call on hold)


18/20

MAKING CALLSCONTINUED

Function Action

Toggle between two Press and holdactive calls the Call button

Join a 3-way call Press and holdboth Volume buttons

Put an active call on Press and hold thehold or resume a call Call button until youon hold hear a beep

Disable or enable the Press and holdindicator light both Volume

buttons for 3 to 4seconds

Mute or unmute a call Tap both Volumebuttons

Note: Some features are phone/network dependent.


19/20

INDICATOR LIGHTSThe indicator light provides information aboutyour headset status.

With the Charger Plugged InHeadset Indicator Headset Status

On (steady) ChargingOff Charging complete

With No Charger Plugged In

Headset Indicator Headset StatusOff Power offOn (steady) Pairing mode

10 rapid flashes Pairing successfulSlow pulse Connected

(on a call)Quick flash Standby

(not on call)Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.


20/20

AUDIO TONESThe audio tones provide information about your

headset status.

Audio Tone Headset StatusSingle high tone when Volume at minimumpressing volume button or maximumFive rapid high tones Low batteryrepeated every 60 sec.No audio indications; Out of rangedeteriorating qualityRing tone Incoming callSingle high tone Pairing confirmationSingle low tone Voice activation

Dual high/low tone Voice tag notrecognizedSingle high tone End callLow to high tone Phone network

not availableTwo ascending tones Mute enabled

H500 Bluetooth Fone

Documents

Transcript of H500 Bluetooth Fone