H 1. 4X DIMPLES REMOVED UPDATED TO AID MFG (S2, C5 & … · 2017-05-22 · 14 cutout increased from...
5
B D C A E F G H B D C A E F G H 2 1 3 4 5 6 7 8 9 2 1 3 4 5 6 7 8 9 10 2 1. MATERIAL CHANGE FROM SUS301 TO SUS304-1/2H 2. DESIGN UPDATED TO AID MFG 2016/08/19 SM 3 1. 4X DIMPLES REMOVED 2. DESIGN UPDATED 2016/08/23 SM 4 UPDATED TO AID MFG (S2, C5 & C4) 2016/08/24 SM 5 UPDATED TANG 2016/08/29 SM 2016/09/26 7 1. UPDATED DESIGN (G7 & G5, S2) 2. SECTION E-E (S3) 3. ADDED PAGE 5 2016/09/30 SM 8 1. UPDATED DESIGN WITH TOLERANCE (G7 & G5, S2) 2. UPDATED INSPECTION DIMENSION (G8,S4) 3. NOTE UPDATED (C5, S5) 2016/10/06 SM 9 UPDATED CALL OUT FOR LASER ENGRAVING (SHEET 5) TO MATCH 1301051_REV6 2016/10/12 SM 10 UPDATED DIMENSIONS REFER TO 2016/10/13 SM 11 UPDATED DIMENSIONS REFER TO - SHEET 2 2016/10/14 SM 12 REFER TO FOR UPDATES - (D10, H5, H7, G2, SHEET 2), (G9, B9, C3, SHEET 3), (E6, SHEET 4) 2016/10/19 SM 13 1. REFER TO FOR UPDATES - SHEET 2 (S2) 2. DIMENSIONS DELETED: 3.92 (B7,S2), 2.40 - 2 PLACES (B7,S2), 10.51 (B5,S2) 2016/11/07 SM 14 CUTOUT INCREASED FROM 1.9MM TO 3.75MM (H5, S5) 2016/11/30 SM 15 1. UPDATED OVERALL TANG DESIGN (G9, F9, SHEET 2) + (G9, F9, SHEET 3) 2. DETAIL F (A4, SHEET 3) 3. OVERALL VERTICAL DIMENSION LIMITS (E6, SHEET 4) 2016/12/07 SM 16 1. ACCEPTED DFM FROM VENDOR - TANG OBROUND CUTOUT UPDATED (G9, F9 & SHEET 2) 2. ACCEPTED DFM FROM VENDOR - GTOL UPDATED (B4, B8 & SHEET 2) 2016/12/19 SM 2017/04/21 UNLESS OTHERWISE NOTED, THIS DOCUMENT CONTAINS SIERRA WIRELESS CONFIDENTIAL INFORMATION. REPRODUCTION, USE, DISCLOSURE OR TRANSMITTAL OF ALL OR ANY PORTION OF THIS DOCUMENT IS PROHIBITED, EXCEPT TO THE EXTENT APPROVED BY SIERRA WIRELESS. SIERRA WIRELESS EXPRESSLY RESERVES ALL RIGHTS UNDER PATENTS, TRADEMARKS, COPYRIGHTS AND TRADE SECRETS. COPYRIGHT (C) 2013, SIERRA WIRELESS. REV DESCRIPTION ECO DATE DRAWN APPD 1 INITIAL RELEASE JUL/29/2016 SM 6 UPDATE PER DFM: SHEET 2, G-9 AUX. VIEW J-J ADDED, F-2, DIM.25 WAS 26 SHEET 3, G-9, DETAIL G ADDED WT 17 TOLERANCE UPDATE PER DFM AT SHEET #4, ADD NOTE AND PICTURE WT WM UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE PER THE FOLLOWING TOLERANCES: MM .X # .50 .XX # .25 .XXX # .15 ANGLES X #5$ X.X #1$ MATERIAL SEE NOTES FINISH SEE NOTES DO NOT SCALE PRINT PROJECT NAME PART DESCRIPTION FX30 DIN & FLAT MOUNT BRACKET DRWN DATE S.MAR JUL/29/2016 DES ENGR DATE S.MAR JUL/29/2016 CHK DATE PRT FILENAME 1301050 DRW FILENAME 1301050 RELEASE LEVEL Development 22 13811 Wireless Way Richmond, British Colu Canada, V6V 3A4 Tel: 604.231.1100 Fax: 604.231.1109 SIZE UNITS DRAWING NO. REV C MM 1301050 17 SCALE: 1.000 SHEET 1 OF 5 I NOTES APPLICABLE TO PART MANUFACTURER 1. DESCRIPTION AND APPLICATION: BRACKET TO BE USED IN WIRELESS DEVICE 2. APPLICABLE DOCUMENTS: ASME Y14.5M-1994 GEOMETRIC DIMENSIONING AND TOLERANCING DOC NO. 2140122 SIERRA WIRELESS - GENERAL COSMETIC SPECIFICATION MOUNT COMPONENTS FOR AUTOMATIC HANDLING IF APPLICABLE 3. MATERIAL AND TOOLING REQUIREMENTS: 3.1 MATERIAL: AISI 304-1/2H STAINLESS STEEL 3.2 THICKNESS: 0.80mm +/- 0.05 3.3 PASSIVATE PER ASTM A-967 3.4 COMPLETE TOOL DRAWINGS TO BE SUBMITTED TO SIERRA WIRELESS MECHANICAL ENGINEERING GROUP FOR APPROVAL. 3.5 THE PART SHALL CONTAIN NO HAZARDOUS SUBSTANCES PER THE WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) 2002/96/EC RoHS DIRECTIVE. 4. MECHANICAL REQUIREMENTS: 4.1 CONTROLLING GEOMETRY IS DEFINED BY THE 3D PRO/ENGINEER DATABASE. ALL SURFACES TO BE WITHIN 0.10mm OF DATABASE UNLESS OTHERWISE SPECIFIED. WHEREVER A CONFLICT EXISTS BETWEEN THE DRAWING AND THE DATABSE, THE DRAWING SHALL TAKE PRECEDENCE. 4.2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 4.3 A REFERENCE DIMENSION IS USED FOR INFORMATIONAL PURPOSES ONLY AND HAS NO TOLERANCE. IT IS DESIGNATED BY: (XX.XX). 4.4 MAXIMUM BURR HEIGHT: 0.13mm. NO LOOSE BURRS PERMITTED. 4.5 ALL INSIDE BEND RADII NOT SHOWN SHALL BE 0.13mm. 4.6 ALL FILLETS AND ROUNDS NOT SHOWN SHALL BE 0.15mm. 4.7 DRAFT ANGLES SHALL BE PER THE 3D PART MODEL UNLESS OTHERWISE SPECIFIED. 4.8 MIN RADII SHALL BE 0.13mm FOR ALL UNMARKED FILLETS AND RADII, UNLESS OTHERWISE SPECIFIED. 5. QUALITY ASSURANCE REQUIREMENTS: 5.1 ALL DIMENSIONS INDICATED ON DRAWING ARE CRITICAL TO FORM, FIT, OR FUNCTION. 5.2 DIMENSIONS INDICATED WITH A X SYMBOL DENOTE QUALITY PROCESS CONTROL, (QPC), DIMENSIONS. 5.3 QUALITY ASSURANCE PLAN: 5.3.1 THE SUPPLIER MUST DEVELOP A QUALITY ASSURANCE PLAN TO ENSURE CRITICAL PARAMETER COMPLIANCE. THE PLAN MUST BE SUBMITTED TO SIERRA WIRELESS FOR REVIEW. 5.3.2 THE SUPPLIER MUST MAINTAIN STATISTICAL PROCESS CONTROL, (SPC), OR 100% INSPECTION ON X PARAMETERS. 5.3.3 PRODUCTION LOT SAMPLES MUST DEMONSTRATE A Cpk VALUE OF 1.33 OR HIGHER. IF THE Cpk DROPS BELOW 1.33 AT ANY TIME DURING THE MANUFACTURE OF THIS PART, THEN THE SUPPLIER MUST 100% SCREEN ALL THOSE PARTS TO THOSE SPECIFIED CRITICAL PARAMETERS. 5.4 FIRST ARTICLE: 5.4.1 FIRST ARTICLE VERIFICATION IS REQUIRED PRIOR TO INITIAL TOOL APPROVAL OR APPROVAL OF A TOOLING CHANGE. FIRST ARTICLE SHALL BE VERIFIED BY A RUN OF AT LEAST 50 PIECES UNDER CONDITIONS REPRESENTATIVE OF PRODUCTION. 5.5 DIMENSIONAL REPORT: 5.5.1 CRITICAL PARAMETER CONFORMANCE MUST BE DEMONSTRATED BY INSPECTION OF AT LEAST 30 PIECES, PER CAVITY, FROM THE FIRST ARTICLE RUN. ALL DRAWING DIMENSIONS MUST BE MEASURED ON AT LEAST 5 PARTS, PER CAVITY, OF THE FIRST ARTICLE RUN. A DIMENSIONAL REPORT MUST BE SUBMITTED TO SIERRA WIRELESS ALONG WITH THE MEASURED PARTS. 6. PACKAGING: 6.1 PARTS SHALL BE PACKAGED IN REUSEABLE, DIVIDED BOXES OF 100 TO 200 PARTS PER BOX 7. EXCEPTIONS: 7.1 NO CHANGE SHALL BE ALLOWED ON PRODUCTION MATERIAL, REGARDLESS OF WHETHER SUCH CHANGE AFFECTS REQUIREMENTS SPECIFIED, WITHOUT PRIOR EXPLICIT WRITTEN APPROVAL BY SIERRA WIRELESS MECHANICAL ENGINEERING GROUP. II NOTES APPLICABLE TO CONTRACT MANUFACTURER 1. INCOMING INSPECTION DIMENSION MARKED BY XX.XX 2. SAMPLE INSPECTION PER QEI-II-0000-18 3. CONTRACT MANUFACTURER SHALL REQUIRE PART MANUFACTURER TO PROVIDE SPC DATA AND REVIEW WITH SIERRA WIRELESS MECHANICAL ENGINEERING GROUP 10 11 12 13 14 15 16 16
Transcript of H 1. 4X DIMPLES REMOVED UPDATED TO AID MFG (S2, C5 & … · 2017-05-22 · 14 cutout increased from...
B
D
C
A
E
F
G
H
B
D
C
A
E
F
G
H
2 13456789
2 1345678910
2 1. MATERIAL CHANGE FROM SUS301 TO SUS304-1/2H2. DESIGN UPDATED TO AID MFG 2016/08/19 SM
3 1. 4X DIMPLES REMOVED 2. DESIGN UPDATED 2016/08/23 SM
4 UPDATED TO AID MFG (S2, C5 & C4) 2016/08/24 SM
5 UPDATED TANG 2016/08/29 SM
2016/09/26
71. UPDATED DESIGN (G7 & G5, S2)2. SECTION E-E (S3)3. ADDED PAGE 5
2016/09/30 SM
81. UPDATED DESIGN WITH TOLERANCE (G7 & G5, S2)2. UPDATED INSPECTION DIMENSION (G8,S4)3. NOTE UPDATED (C5, S5)
2016/10/06 SM
9 UPDATED CALL OUT FOR LASER ENGRAVING (SHEET 5) TO MATCH 1301051_REV6 2016/10/12 SM
10 UPDATED DIMENSIONS REFER TO 2016/10/13 SM
11 UPDATED DIMENSIONS REFER TO - SHEET 2 2016/10/14 SM
12 REFER TO FOR UPDATES - (D10, H5, H7, G2, SHEET 2), (G9, B9, C3, SHEET 3), (E6, SHEET 4) 2016/10/19 SM
131. REFER TO FOR UPDATES - SHEET 2 (S2) 2. DIMENSIONS DELETED: 3.92 (B7,S2), 2.40 - 2 PLACES (B7,S2), 10.51 (B5,S2)
2016/11/07 SM
14 CUTOUT INCREASED FROM 1.9MM TO 3.75MM (H5, S5) 2016/11/30 SM
15 1. UPDATED OVERALL TANG DESIGN (G9, F9, SHEET 2) + (G9, F9, SHEET 3) 2. DETAIL F (A4, SHEET 3) 3. OVERALL VERTICAL DIMENSION LIMITS (E6, SHEET 4)
2016/12/07 SM
161. ACCEPTED DFM FROM VENDOR - TANG OBROUND CUTOUT UPDATED (G9, F9 & SHEET 2) 2. ACCEPTED DFM FROM VENDOR - GTOL UPDATED (B4, B8 & SHEET 2)
2016/12/19 SM
2017/04/21
UNLESS OTHERWISE NOTED, THIS DOCUMENT CONTAINS SIERRA WIRELESS CONFIDENTIALINFORMATION. REPRODUCTION, USE, DISCLOSURE OR TRANSMITTAL OF ALL OR ANYPORTION OF THIS DOCUMENT IS PROHIBITED, EXCEPT TO THE EXTENT APPROVED BYSIERRA WIRELESS. SIERRA WIRELESS EXPRESSLY RESERVES ALL RIGHTS UNDER PATENTS,TRADEMARKS, COPYRIGHTS AND TRADE SECRETS. COPYRIGHT (C) 2013, SIERRA WIRELESS.
REV DESCRIPTION ECO DATE DRAWN APPD
1 INITIAL RELEASE JUL/29/2016 SM
6 UPDATE PER DFM: SHEET 2, G-9 AUX. VIEW J-J ADDED, F-2, DIM.25 WAS 26SHEET 3, G-9, DETAIL G ADDED WT
17 TOLERANCE UPDATE PER DFM AT SHEET #4, ADD NOTE AND PICTURE WT WM
UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE PER THE FOLLOWING TOLERANCES:
MM.X �#� .50.XX �#� .25.XXX �#� .15
ANGLESX �#�5�$�X.X �#�1�$�
MATERIAL
SEE NOTESFINISH
SEE NOTES
DO NOT SCALE PRINT
PROJECT NAME PART DESCRIPTION
FX30 DIN & FLAT MOUNT BRACKETDRWN DATE
S.MAR JUL/29/2016DES ENGR DATE
S.MAR JUL/29/2016CHK DATE
PRT FILENAME
1301050DRW FILENAME
1301050RELEASE LEVEL
Development 22
13811 Wireless WayRichmond, British ColumbiaCanada, V6V 3A4Tel: 604.231.1100Fax: 604.231.1109
SIZE UNITS DRAWING NO. REV
C MM 1301050 17SCALE: 1.000 SHEET 1 OF 5
I NOTES APPLICABLE TO PART MANUFACTURER 1. DESCRIPTION AND APPLICATION: BRACKET TO BE USED IN WIRELESS DEVICE 2. APPLICABLE DOCUMENTS: ASME Y14.5M-1994 GEOMETRIC DIMENSIONING AND TOLERANCING DOC NO. 2140122 SIERRA WIRELESS - GENERAL COSMETIC SPECIFICATION MOUNT COMPONENTS FOR AUTOMATIC HANDLING IF APPLICABLE 3. MATERIAL AND TOOLING REQUIREMENTS: 3.1 MATERIAL: AISI 304-1/2H STAINLESS STEEL 3.2 THICKNESS: 0.80mm +/- 0.05 3.3 PASSIVATE PER ASTM A-967 3.4 COMPLETE TOOL DRAWINGS TO BE SUBMITTED TO SIERRA WIRELESS MECHANICAL ENGINEERING GROUP FOR APPROVAL. 3.5 THE PART SHALL CONTAIN NO HAZARDOUS SUBSTANCES PER THE WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) 2002/96/EC RoHS DIRECTIVE. 4. MECHANICAL REQUIREMENTS: 4.1 CONTROLLING GEOMETRY IS DEFINED BY THE 3D PRO/ENGINEER DATABASE. ALL SURFACES TO BE WITHIN 0.10mm OF DATABASE UNLESS OTHERWISE SPECIFIED. WHEREVER A CONFLICT EXISTS BETWEEN THE DRAWING AND THE DATABSE, THE DRAWING SHALL TAKE PRECEDENCE. 4.2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 4.3 A REFERENCE DIMENSION IS USED FOR INFORMATIONAL PURPOSES ONLY AND HAS NO TOLERANCE. IT IS DESIGNATED BY: (XX.XX). 4.4 MAXIMUM BURR HEIGHT: 0.13mm. NO LOOSE BURRS PERMITTED. 4.5 ALL INSIDE BEND RADII NOT SHOWN SHALL BE 0.13mm. 4.6 ALL FILLETS AND ROUNDS NOT SHOWN SHALL BE 0.15mm. 4.7 DRAFT ANGLES SHALL BE PER THE 3D PART MODEL UNLESS OTHERWISE SPECIFIED. 4.8 MIN RADII SHALL BE 0.13mm FOR ALL UNMARKED FILLETS AND RADII, UNLESS OTHERWISE SPECIFIED. 5. QUALITY ASSURANCE REQUIREMENTS: 5.1 ALL DIMENSIONS INDICATED ON DRAWING ARE CRITICAL TO FORM, FIT, OR FUNCTION. 5.2 DIMENSIONS INDICATED WITH A X SYMBOL DENOTE QUALITY PROCESS CONTROL, (QPC), DIMENSIONS. 5.3 QUALITY ASSURANCE PLAN: 5.3.1 THE SUPPLIER MUST DEVELOP A QUALITY ASSURANCE PLAN TO ENSURE CRITICAL PARAMETER COMPLIANCE. THE PLAN MUST BE SUBMITTED TO SIERRA WIRELESS FOR REVIEW. 5.3.2 THE SUPPLIER MUST MAINTAIN STATISTICAL PROCESS CONTROL, (SPC), OR 100% INSPECTION ON X PARAMETERS. 5.3.3 PRODUCTION LOT SAMPLES MUST DEMONSTRATE A Cpk VALUE OF 1.33 OR HIGHER. IF THE Cpk DROPS BELOW 1.33 AT ANY TIME DURING THE MANUFACTURE OF THIS PART, THEN THE SUPPLIER MUST 100% SCREEN ALL THOSE PARTS TO THOSE SPECIFIED CRITICAL PARAMETERS. 5.4 FIRST ARTICLE: 5.4.1 FIRST ARTICLE VERIFICATION IS REQUIRED PRIOR TO INITIAL TOOL APPROVAL OR APPROVAL OF A TOOLING CHANGE. FIRST ARTICLE SHALL BE VERIFIED BY A RUN OF AT LEAST 50 PIECES UNDER CONDITIONS REPRESENTATIVE OF PRODUCTION. 5.5 DIMENSIONAL REPORT: 5.5.1 CRITICAL PARAMETER CONFORMANCE MUST BE DEMONSTRATED BY INSPECTION OF AT LEAST 30 PIECES, PER CAVITY, FROM THE FIRST ARTICLE RUN. ALL DRAWING DIMENSIONS MUST BE MEASURED ON AT LEAST 5 PARTS, PER CAVITY, OF THE FIRST ARTICLE RUN. A DIMENSIONAL REPORT MUST BE SUBMITTED TO SIERRA WIRELESS ALONG WITH THE MEASURED PARTS. 6. PACKAGING: 6.1 PARTS SHALL BE PACKAGED IN REUSEABLE, DIVIDED BOXES OF 100 TO 200 PARTS PER BOX 7. EXCEPTIONS: 7.1 NO CHANGE SHALL BE ALLOWED ON PRODUCTION MATERIAL, REGARDLESS OF WHETHER SUCH CHANGE AFFECTS REQUIREMENTS SPECIFIED, WITHOUT PRIOR EXPLICIT WRITTEN APPROVAL BY SIERRA WIRELESS MECHANICAL ENGINEERING GROUP. II NOTES APPLICABLE TO CONTRACT MANUFACTURER 1. INCOMING INSPECTION DIMENSION MARKED BY XX.XX 2. SAMPLE INSPECTION PER QEI-II-0000-18 3. CONTRACT MANUFACTURER SHALL REQUIRE PART MANUFACTURER TO PROVIDE SPC DATA AND REVIEW WITH SIERRA WIRELESS MECHANICAL ENGINEERING GROUP
10
11
12
13
14
15
16
16
B
D
C
A
E
F
G
H
B
D
C
A
E
F
G
H
2 1345678910
2 1345678910
J
J
0.0
21.2
0.0
26.2
48.2
53.2
0.0
7.2
0.0
29.2
45.2
4X 67.2
(GUSSET)16 1
(GUSSET)59 1
0.0
2X 3.7
0.0
2X 7.0
22 1
52 1
5X 4.25
6 1
7.2
12.7
18.2
3X 4.4+0.2 0
23.1
3X 37.10
53.10
32.1
43.1
58
62.7
68.7
2X 2.0
31.2
43.2
2X 23 1
2X 44 1
2X 2.20 0.15
0.0
4X 2.7
0.0
21.2
47.4
28.3
41.6
5X 34.30
2X 62.3
2X 65.60
2X 71
1
63
1
2X 2+1 0
2X 2.30
2X 5.70
0.20
15.3
13.2
20.7
2X 62.62
0.20
67.6
39.3
29.3
2.0
13.3
19.3
50.6
56.6
43.6
48.6
26.3
27.3
41.3
11.6
22.3
31.7
36.9
41.8
60.7
0.00
7.72
0.00
14.31
16.1
0.00
8.00
0.00
2X 12.2
0.0
20.2
0.0
56.2
42.139.6
34.632.1
43.1 0.5
32.1 0.5
2X R2.5
37.60
0.0
( )37.2
0.0
11.55
41.80
0.0
1.0+0.5
0
0.0
2 PLACES �s�3.30 0.20
0.80
0.0
7.0
0.0
50.8
43.8
54.2
59.1
52.8
(GUSSET)25 1
(GUSSET)51 1
R TYP.1.0
1.0
(R )40
4.5+0.5-1.0
2.0
A
B
C
�A�|�B�|�C
A
A
COPLANAR �u�
�A�|�B�|�C
13811 Wireless WayRichmond, British ColumbiaCanada, V6V 3A4Tel: 604.231.1100Fax: 604.231.1109
SIZE DRAWING NO. REV
C 1301050 17SCALE: 1.000 SHEET 2 OF 5
X
X
(STANDARD TOLERANCE FOR SUS304)
AUX VIEW J-J
PUNCH DIRECTION
SEE DETAIL H
X
REFER TO 3D MODEL FOR GUSSET REFERENCE
X
SECTION A-A
SEE DETAIL K
SECTION C-C
SEE DETAIL K
SEE DETAIL H
16
16
16
16
B
D
C
A
E
F
G
H
B
D
C
A
E
F
G
H
2 1345678910
2 1345678910
0.55 0-0.20
R2 1
231�$�5�$�
0.00.0
67.3 1.0
0.00
5.50
0.00
7.50
3.30
1.60
RTAB �u�0.4
( )5.6
REF.5.0�$�+3.0�$�-3.0�$�
R1.4
0.8
9.2
5.2
3.20
REF.45�$�
14.6 1.0
0.002.7 1.0
0.00
(TIP)74.4 0.4
64.7 1.0
( )0.85
A
13811 Wireless WayRichmond, British ColumbiaCanada, V6V 3A4Tel: 604.231.1100Fax: 604.231.1109
SIZE DRAWING NO. REV
C 1301050 17SCALE: 1.000 SHEET 3 OF 5
DETAIL KSCALE 4.000
2 PLACES
DETAIL HSCALE 4.000
8 PLACES
TANGENTREFER TO SHEET 2FOR TOLERANCE
X
SECTION D-D
TAB �u�
TAB �s�
SEE DETAIL E
SEE DETAIL G
SEE DETAIL F
SECTION B-B
DETAIL ESCALE 8.000
2 PLACES
DETAIL GSCALE 8.000
2 PLACES
TAB �s�2 PLACES
DETAIL FSCALE 10.000
SECTION E-ESCALE 4.000
B
D
C
A
E
F
G
H
B
D
C
A
E
F
G
H
2 1345678910
2 1345678910
57.1256.72
73.8573.55
3.71+0.20-0.30
10.31+0.20-0.30
13811 Wireless WayRichmond, British ColumbiaCanada, V6V 3A4Tel: 604.231.1100Fax: 604.231.1109
SIZE DRAWING NO. REV
C 1301050 17SCALE: 1.000 SHEET 4 OF 5
1301015 [FLAT MOUNT BRACKET] MUSTSNAP FIT WITH 1301050 [DIN BRACKET]
START ASSEMBLY
FINISH ASSEMBLY
THESE TWO FEATURES MUST FIT INTO SIDE GROOVESOF EXTRUSION 1304245 WITH HAND ASSEMBLY.THE ASSEMBLED SET MUST PASS DROP TESTFROM 1.3 METER HEIGHT TO CONCRETE FLOORWITHOUT SEPARATION.
1301051 [FLAT MOUNT BRACKET] SLIDE FLAT MOUNT BRACKET ONTO DIN BRACKET
1301050 - DIN BRACKET
17
17
17
B
D
C
A
E
F
G
H
B
D
C
A
E
F
G
H
2 1345678910
2 1345678910
A
C
13811 Wireless WayRichmond, British ColumbiaCanada, V6V 3A4Tel: 604.231.1100Fax: 604.231.1109
SIZE DRAWING NO. REV
C 1301050 17SCALE: 1.000 SHEET 5 OF 5
SCALE 3.000
SEE DETAIL AGRAPHIC: APPROX. LOCATION AS SHOWN (REFER TO 3D CAD FILE)
MANUFACTURING METHOD: LASER ENGRAVING (NO STAINING, ANNEALING MARKING, RUSTING OR OXIDATION ALLOWED AFTER LASER ENGRAVING).
DETAIL ASCALE 6.000
