GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

download GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

of 25

Transcript of GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    1/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Code Product Name BTS3900

    User GBSS Engineer Product Version V1.0

    Drafted B !ire"ess Case and Training Date #00$%0&%#'

    GS( BTS3900

    )nsite Engineer )*erationGuide

    Huawei Technologies Co. td.

    !ll rights reser"ed

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    2/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    +ntroduction

    #. GSM BTS3900 Onsite Engineer Operation Guide is one part o$

    the BTS3900 training pac%age& which is designed to support

    the training wor% a'road. The (ain purpose o$ this docu(ent is

    to $acilitate the onsite engineers to 'e (uch clear a'out the %e)

    points in the engineering and co((issioning wor%.

    *. This docu(ent can not 'e used to direct the engineering wor%

    in a certain pro+ect without (odi$ication to (atch the detailed

    pro+ect scenario ') technical director.

    3. ,lease re$er to the BTS3900 -eplo)(ent Guide& Installation

    Guide and other docu(ents to direct the engineering and

    co((issioning wor%.

    #

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    3/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Content

    Chapter # BTS3900 Onsite Engineer Operation ,reparation..............................................3

    #.# -ocu(ents ,reparation.................................................................................................... 3

    1.1.1 GSM BTS3900 Survey Report........................................................................................3

    1.1.2 GSM BTS3900 Engineering Documents.........................................................................3

    1.1.3 GSM BTS3900 Instaation Gui!e...................................................................................3

    1.1." #ar!$are Instaation %uaity Se&'inspection Report ( )n'site *ommissioning

    Report

    .....................................................................................................................................................3

    #.* ecessar) Tools and Meters.............................................................................................3

    Chapter * BTS3900 Onsite Engineer Operation Guide......................................................./

    *.# npac%ing Chec%............................................................................................................../

    *.* BTS3900 Hardware Installation......................................................................................... /

    2.2.1 Instaing t+e BTS3900 *a,inet......................................................................................."

    2.2.2 Instaing t+e E-terna G/D *a,es o& t+e BTS3900..................................................."

    2.2.3 Instaing t+e BB3900....................................................................................................

    2.2." Instaing t+e MS...................................................................................................

    2.2. Instaing t+e G/D ca,e o& t+e D*D.........................................................................9

    2.2.4 Instaing 5"67 BTS3900 o$er *a,es.......................................................................10

    2.2. Instaing t+e BTS3900 Transmission *a,es................................................................11

    2.2.6 Instaing t+e BTS3900 Signa *a,es...........................................................................13

    2.2.9 Instaing t+e R8 Signa *a,es......................................................................................16

    *.3 Chec%ing the Installation o$ the BTS3900 Hardware....................................................... *0

    *./ Co((issioning o$ BTS3900............................................................................................ *#

    2.".1 oca Maintenance.........................................................................................................21

    2.".2 Transmission Testing......................................................................................................22

    2.".3 Data oa!ing .................................................................................................................22

    2."." Monitoring t+e Device Status........................................................................................22

    *

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    4/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2.". Measuring t+e )utput o$er ........................................................................................22

    2.".4 *a Testing.....................................................................................................................22

    2.". Environment :arms Testing..........................................................................................23

    !ttach(ent...............................................................................................................................*/

    C,a*ter 1 BTS3900 )nsite Engineer )*erationPre*aration

    #.# -ocu(ents ,reparation

    #.#.# GSM BTS3900 Sur"e) 1eport

    O'tain the BTS3900 sur"e) report $ro( the T-.

    2a(iliar with the site position& en"iron(ent and other details in the sur"e) report.

    #.#.* GSM BTS3900 Engineering -ocu(ents

    ,a) attention to the $ollowing in$or(ation $ront "iew and top "iew o$ antenna4$eeder&

    installation position o$ the antenna s)ste(& antenna height& direction& tilt angle& etc.& in order

    to direct the antenna s)ste( installation and ca'le connection.

    #.#.3 GSM BTS3900 Installation Guide

    BTS3900 5uic% Installation Guide

    BTS3900 Installation Guide

    #.#./ Hardware Installation 5ualit) Sel$6inspection 1eport 7 On6siteCo((issioning 1eport

    #.* ecessar) Tools and Meters

    SN Too"s-(eters uantit# SITEM!STE1 #

    * ,ower Meter #

    3 Test ,hone #

    / SIM card $or testing #

    8 SIM card o$ other operators with the sa(e

    $reuenc) 'and

    #

    : Current tools o$ wireless engineering #

    *

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    5/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    C,a*ter # BTS3900 )nsite Engineer )*erationGuide

    *.# npac%ing Chec%

    )*eration Procedures

    Step # Bring the printed pac%ing6lists while lea"ing $or the unpac%ing chec%ing.

    Step * Inspect all the ite(s on the pac%ing6list and trans$er the docu(ents to the T- a$ter

    getting custo(er;s signature.

    Step 3 2or cargo pro'le( in the unpac%ing chec%ing& please $ill in ternal ,G- Ca'les o$ the BTS3900

    )*eration Procedures

    Step # Based on the actual ca'ling route o$ the ,G- ca'les& (easure the distant 'etween

    the ,G- 'olt o$ the BTS3900 ca'inet and the corresponding connecting ter(inal o$

    an e>ternal grounding 'ar& and o'tain ,G- ca'les in appropriate length.

    Step * !ttach the te(porar) la'els at 'oth ends o$ a ca'le. The contents on the la'els can

    'e consistent with the $or(al ones or 'e sel$6prepared.

    Step 3 Ma%e OT ter(inals at 'oth ends o$ each ,G- ca'le.

    Step / 1oute the ,G- ca'les.

    Step 8 Connect the OT ter(inal at one end o$ the ,G- ca'le to the grounding point o$ theBTS3900 ca'inet& as shown in 2igure #.

    *0#36##6*? H!@EI Con$idential ,age/& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    6/25

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    7/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    @hether to ena'le the !'is ')pass $unction depends on the actual reuire(ents. The -I,

    switches S/ and S8 on the GTM are used to set whether to ena'le the !'is ')pass $unction&

    as shown in Ta'le *.

    Ta'le * The Setting o$ -I, switches S/ and S8

    )*eration Procedures

    Step # Hold the BB with 'oth hands and align the holes in each hanger with the

    corresponding (ounting holes in the ca'inet. Then& slowl) push the BB along the

    guide rail.

    Step * Thread each o$ the $our screws through the hanger and (ounting hole in the ca'inet.

    Then& use the cross screwdri"er to tighten the screws so that the BB is $astened in

    the ca'inet& as shown in 2igure *.

    Note

    In the case o$ a 6/D -C ca'inet& the BB should 'e installed in the position 3 awa) $ro(

    the 2! unit. In the case o$ a */D -C or **0D !C ca'inet& the BB should 'e installed in

    the position * awa) $ro( the 2! unit.

    *0#36##6*? H!@EI Con$idential ,age:& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    8/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure * Installing the BB3900

    //End

    *.*./ Installing the ,M4,S

    !arning

    Be$ore contacting the de"ice& wear a grounded ES- wrist strap or glo"es. It can pre"ent the

    sensiti"e co(ponents $ro( 'eing da(aged ') the static electricit) in the hu(an 'od).

    Note

    In the case o$ a **0D !C ca'inet& )ou should install the ,M and ,S A!C4-C. The **0D

    !C ca'inet can 'e con$igured with a (a>i(u( o$ one ,M and three ,Ss. In the case o$ a

    */D -C ca'inet& )ou should install the ,S A-C4-C. The */D -C ca'inet can 'e

    con$igured with a (a>i(u( o$ $our ,Ss.

    Prereuisites

    -ip 'its # and * on the rear panel o$ the ,M are set to O& and the other si> -I, 'its are set

    to O22& as shown in 2igure 3.

    *0#36##6*? H!@EI Con$idential ,age?& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    9/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure 3 The setting o$ -I, switches on the ,M

    Note

    I$ two ,Ms are con$igured and the ports $or (onitoring the ,Ms are logicall) on the sa(e

    'us& 'it 3 o$ the -I, switch on the second ,M should 'e set to O and the other 'its should'e set to O22. I$ the ports $or (onitoring the ,Ms are logicall) on di$$erent 'uses& the

    settings o$ the -I, switches on the two ,Ms can 'e the sa(e.

    )*eration Procedures

    Step # On the ,M4,S panel& loosen the two screws to un$old the handle& as shown in

    2igure /.

    2igure / oosen the screws on the panel

    Note

    2igure / shows the screws on the ,M panel. The positions o$ the screws on the ,S panel

    are the sa(e as those on the ,M panel.

    *0#36##6*? H!@EI Con$idential ,age& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    10/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Step * Slide the ,M4,S $orward along the guide rail until )ou $eel resisting $orce& as

    shown in 2igure 8.

    2igure 8 Installing the ,M

    Step 3 2old the handle& and then tighten the two screws on the panel& as shown in 2igure 8.

    Step / Install the other ,M and ,Ss $ro( the le$t to the right.

    //End

    *.*.8 Installing the ,G- ca'le o$ the -C-

    )*eration Procedures

    Step # 1oute the ,G- ca'les o$ the -C-.

    Step * Connect the OT ter(inal at one end o$ the ,G- ca'le to the corresponding G-

    ter(inal o$ the BTS3900 ca'inet and connect the OT ter(inal at the other end o$ the

    ca'le to the grounding 'ar at the lower6right o$ the -C-& as shown in 2igure :.

    *0#36##6*? H!@EI Con$idential ,age9& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    11/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure : Installing the ,G- ca'le o$ the -C-

    Step 3 Tighten the screws ') using the cross screwdri"er.//End

    *.*.: Installing F/D BTS3900 ,ower Ca'les

    This section descri'es onl) the installation (ethod and procedures o$ the e>ternal 6/D input

    power ca'les and the power ca'les o$ the (odules in the BTS3900 ca'inet when the

    BTS3900 ca'inet supports 6/D power input. ,lease re$er to the chapter ternal 'olt o$ the ter(inal 'loc% ') using the cross screwdri"er& and

    disasse('le the protection co"er on the e>ternal ter(inal 'loc% o$ the power suppl)

    in the -C-.

    Step 8 See the procedures $or installing the OT ter(inals. Connect the OT ter(inals o$ the

    power ca'les to the corresponding ter(inal. Connect the OT ter(inal o$ each 6/ D

    power ca'le A'lue to the EGA6 ter(inal& and connect the OT ter(inal o$ each G-

    ca'le A'lac% to the 1TA ter(inal& as shown in 2igure ?.

    2igure ? Installing the e>ternal power ca'les o$ the -C-

    Step : Tighten the screws in the ca'le hole ') using the cross screwdri"er.

    Step ? ,lace the protection co"er on the -C-& and then tighten the screw on the

    *0#36##6*? H!@EI Con$idential ,age#0& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    12/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    protection co"er ') using the cross screwdri"er.

    //End

    Installing the ,ower Ca'les 'etween the -C- and the -12s

    )*eration Procedures

    Step # Connect the 3D3 connector o$ each power ca'le to the ,@1 port on the

    corresponding -12& as shown in 2igure .

    2igure Installing the power ca'le 'etween the -C- and the -12s

    Step * Tighten the two screws on the 3D3 connector& as shown in 2igure .Step 3 !ttach a la'el to the power ca'le.

    //End

    *.*.? Installing the BTS3900 Trans(ission Ca'les

    Installing the BB E#4T# Ca'le A#96Inch Ca'inet

    I$ the E, 'oard is con$igured& the E#4T# ca'le connects the ca'le connecting euip(ent to

    the OTSI-Eport on the E, 'oard.

    I$ the E, 'oard is not con$igured& the E#4T# ca'le connects the ca'le connecting

    euip(ent to theE#4T#port on the GTM 'oard.

    )*eration Procedures

    Step # 1oute the E#4T# ca'le outside the ca'inet.

    Step * ead the E#4T# ca'le to the ca'inet $ro( the ca'le hole $or the signal ca'le at the

    right side.

    Step 3 Connect the E#4T# ca'le to the port on the E, or the GTM.

    Ta'le 3 -i$$erent wa)s o$ connection o$ E#4T# ca'les

    *0#36##6*? H!@EI Con$idential ,age##& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    13/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    I$... Then...

    The E, 'oardis con$igured&

    Insert the -B*: (ale connector o$ the E# ca'le into theOTSI-E port on the E, and tighten the screws& as shownin 2igure 9. Then& install the E# surge protection trans$er ca'le.

    The E, 'oardis not con$igured&

    Insert the -B*: (ale connector o$ the E# ca'le into the E#4T#port on the GTM and tighten the screws& as shown in 2igure#0. In this case& installing the E# surge protection trans$erca'le is not reuired.

    2igure 9 Connecting the E#4T# ca'le to the E,

    2igure #0 Connecting the E#4T# ca'le to the GTM

    Step / 1oute the E#4T# ca'le 'ased on the ca'ling route at the right side o$ the #96inch

    ca'inet& and $i> the ca'le ') using the ca'le clips.

    Step 8 !ttach a la'el to the E#4T# ca'le.

    //End

    Installing the C,1I Signal Ca'les 'etween the BB and the -12s)*eration Procedures

    Step # Insert the S2, connector at one end o$ each C,1I signal ca'le into the C,1I port on

    the panel o$ the BB (odule.

    Step * Insert the S2, connector at the other end o$ the C,1I signal ca'le into the C,1I0

    port on the panel o$ the -12 (odule& as shown in 2igure ##.

    *0#36##6*? H!@EI Con$idential ,age#*& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    14/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure ## Connections o$ the C,1I ca'le $or a single ca'inet

    //End

    *.*. Installing the BTS3900 Signal Ca'les

    Installing the Monitoring Signal Ca'les $or the -C-60#

    Note

    The ,S $ault alar( can 'e co(pleted ') onl) one channel o$ Boolean alar( signals. The

    pins 3 and : o$ the (onitoring signal ca'le # $or the -C-60# are used to trans(it the alar(

    to the BB.

    The (onitoring signal ca'le # and * $or the -C-60# need to 'e installed during the

    installation o$ the stac%ed ca'inets.

    2igure #* shows the (onitoring signal ca'le # $or the -C-60#.

    *0#36##6*? H!@EI Con$idential ,age#3& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    15/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure #* Monitoring signal ca'le # $or the -C-60#

    Ta'le / descri'es the de$inition and color o$ the pins o$ the (onitoring signal ca'le #.Ta'le / -e$inition and color o$ the pins o$ the (onitoring signal ca'le #

    ,in at the *End

    ,in o$ theConnector at the

    # End

    Color -escription

    ;1 2 Bue T$iste! pair ca,e

    1 ;+ite

    4 )range T$iste! pair ca,e

    3 ;+ite

    ;2 " Bue T$iste! pair ca,e

    ;+ite

    6 )range T$iste! pair ca,e

    ;+ite

    )*eration Procedures

    +nsta""ing t,e monitoring signa" ca"e 1 for t,e DCDU%01 during t,e configuration oft,e %2$V sing"e cainet.

    Step # Connect the 1/8 connector at one end o$ the (onitoring signal ca'le # to the ET6

    !M0 port on the ,E (odule o$ the BB& as shown in 2igure #3.

    2igure #3 Installing the (onitoring signal ca'le 'etween the BB and the -C-60#

    Step * Insert the pins * and # A'lue4white in @# at one end o$ the (onitoring signal ca'le

    # into the S,- !M port on the panel o$ the -C-60#& as shown in 2igure #/.

    *0#36##6*? H!@EI Con$idential ,age#/& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    16/25

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    17/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    2igure #8 Inserting the (onitoring signal ca'le into the stac%ed ca'inet o$ the -C-60#

    Step : !ttach a la'el to the (onitoring signal ca'le.

    Step ? 2i> the interaction ter(inals in the inside ca'ling space at the right o$ the ca'inet.

    //End

    +nsta""ing t,e monitoring signa" ca"e 1 and # for t,e DCDU%01 ,en a 5#2V cainetand a %2$V cainets are stac4ed.

    Step # Connect the 1/8 connector at one end o$ the (onitoring signal ca'le # to the ET6

    !M0 port on the ,E (odule o$ the BB& as shown in 2igure #3.

    Step * Insert the pins * and # A'lue4white in @# into the S,- !M ports on the panel o$ the

    -C-60#& as shown in 2igure #:.

    *0#36##6*? H!@EI Con$idential ,age#:& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    18/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Step 3 Insert the pins and ? Aorange4white in @* into the interaction ter(inals.

    Step / Insert the pins at one end o$ (onitoring signal ca'le * into the interconnection

    ter(inals& as shown in 2igure #:.

    Step 8 Insert the pins at the other end o$ (onitoring signal ca'le * into the S,- !M ports

    on the panel o$ the -C-60#& as shown in 2igure #:.

    2igure #: Installing the (onitoring signal ca'le # and * $or the -C-60# A*/D ca'inet

    Step : Cut the (onitoring signal ca'le # to e>pose the pins : and 3 Aorange4white in @#.

    Step ? Insert the pins : and 3 Aorange4white into the !M port on the connection unit o$ the

    ,S A-C4-C.

    Step !ttach a la'el to the (onitoring signal ca'le.

    Note

    *0#36##6*? H!@EI Con$idential ,age#?& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    19/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    The installation o$ the (onitoring signal ca'le $or the -C-60# in the */ D single ca'inet is

    si(ilar to that o$ the stac%ed ca'inets. ou onl) need to insert pins * and # in @# into the

    S,- !M port on the panel o$ the -C-60#& and insert pins : and 3 into the !M port on the

    connection unit o$ the ,S A-C4-C.

    Step 9 2i> the interaction ter(inals in the inside ca'ling space at the right o$ the ca'inet.

    //End

    Installing the Monitoring Signal Ca'les $or the 2!

    )*eration Procedures

    Step # Insert the 1/8 connector at one end o$ the (onitoring signal ca'le into the MO0

    port on the panel o$ the ,E.

    Step * Insert the 1/8 connector at the other end o$ the (onitoring signal ca'le into the

    COM I port on the panel o$ the 2!& as shown in 2igure #?.

    2igure #? Installing the Monitoring Signal Ca'les $or the 2!

    Step 3 !ttach a la'el to the (onitoring signal ca'le o$ the 2!.//End

    Installing the Monitoring Signal Ca'le $or the EM!

    ,lease re$er to the H!@EI EM! ser Guide.

    *.*.9 Installing the 12 Signal Ca'les

    Installing the 12 u(pers

    )*eration Procedures

    Step # @hen cutting the 12 +u(per& )ou should lea"e 30c( o$ the +u(per $or ease o$ ca'ling

    *0#36##6*? H!@EI Con$idential ,age#& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    20/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    on the upper ca'inet in case that the ca'inets are stac%ed $or capacit) e>pansion.

    Step * Connect one end o$ the +u(per to the +u(per connector at the $eeder side.

    Step 3 Connect the -I connector o$ the +u(per to the !T port on the panel o$ the -12

    (odule& as shown in 2igure #.

    2igure # Connections o$ 12 +u(pers $or a single ca'inet

    Step / Tighten the -I connector ') using the ad+usta'le wrench.

    //End

    Note

    I$ a single ca'inet is installed& the 12 +u(pers are routed along the le$t and right ca'le

    troughs. I$ two ca'inets are stac%ed& the 12 +u(pers in the lower ca'inet are routed along thele$t and right ca'le troughs& and the 12 +u(pers in the upper ca'inet are routed in $ront o$ the

    -12 panels.

    ,lease re$er to the design $ile o$ each pro+ect to see the connection o$ the 12 signal ca'les

    'etween -12s.

    *0#36##6*? H!@EI Con$idential ,age#9& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    21/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    !ttaching Color 1ings

    2igure #9 !ttaching Color 1ings

    *.3 Chec%ing the Installation o$ the BTS3900 Hardware

    Chec% the installation ualit) o$ the hardware according to the ternal power input "oltage is in the range o$ 63./D -C

    68?D -C.

    ,ower on the (odules and chec% the indicators status according to BTS3900 Co((issioning

    Guide.

    *0#36##6*? H!@EI Con$idential ,age*0& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    22/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    *./ Co((issioning o$ BTS3900

    ,lease test the $ollowing ite(s and record the results in On6site Co((issioning 1eport.

    *./.# ocal Maintenance

    Prereuisites

    The I, address and the su'net (as% o$ the Site Maintenance Ter(inal ,C are set. The I,

    address o$ the Site Maintenance Ter(inal ,C and the I, address

    A#9*.#:.0.?*4*88.*88.*88.0 o$ the BTS are on the sa(e networ% seg(ent.

    )*eration Procedures

    Step # se the crosso"er ca'le to connect the Site Maintenance Ter(inal ,C to the BTS.

    Connect one end o$ the ca'le to the ETH port on the (ain control (odule o$ the(ain ca'inet& and connect the other end o$ the ca'le to the Ethernet ca'le port on

    the Site Maintenance Ter(inal ,C.

    Step * Open the co((and window.

    I$ the operating s)ste( o$ the Site Maintenance Ter(inal ,C is @indows 9&

    choose StartJ ,rogra( J MS6-OS ,ro(pt. The co((and window is displa)ed.

    I$ the operating s)ste( o$ the Site Maintenance Ter(inal ,C is @indows

    *0004,& choose Start J 1un. In the 1un dialog 'o>& run the c(d co((and.

    The co((and window is displa)ed.

    Step 3 1un the ping targetKna(eco((and to "eri$) the networ% connection 'etween the ,C

    and the BTS. AtargetKna(e indicates the I, address o$ the BTS.

    I$ the in$or(ation si(ilar to that in the $ollowing e>a(ple is returned& the MT ,C and

    the GB!M can co((unicate nor(all). In this e>a(ple& the I, address o$ the e>ternal

    networ% is #9*.#:.0.?*.

    ,inging #9*.#:.0.?* with 3* ')tes o$ data

    ,inging #9*.#:.0.?* with 3* ')tes o$ data

    1epl) $ro( #9*.#:.0.?* ')tesL3* ti(eL#(s TTL*83

    1epl) $ro( #9*.#:.0.?* ')tesL3* ti(eL#(s TTL*83

    1epl) $ro( #9*.#:.0.?* ')tesL3* ti(eL#(s TTL*83

    1epl) $ro( #9*.#:.0.?* ')tesL3* ti(eL#(s TTL*83

    ,ing statistics $or #9*.#:.0.?*

    ,ac%ets Sent L /& 1ecei"ed L /& ost L 0 A0 loss&

    !ppro>i(ate round trip ti(es in (illi6seconds

    Mini(u( L #(s& Ma>i(u( L #(s& !"erage L #(s

    Step / Start Site Maintenance Ter(inal S)ste(. The path is

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    23/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Step 8 !$ter success$ul co((unication 'etween local (aintenance ter(inal and BTS& set the

    co((unication port para(eter to ed phoneN

    *0#36##6*? H!@EI Con$idential ,age**& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    24/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    Ms to other operators; MS.

    Step 3 Hando"er test $or inter6cell in the sa(e site.

    Step / 1epeat step# to step3 to test the other cells.

    Step 8 ,S call testing& including SMS4MS& we' sur$ing and downloading.

    *./.? En"iron(ent !lar(s Testing

    Test the en"iron(ent alar(s with the cooperation o$ the BSC engineers.

    *0#36##6*? H!@EI Con$idential ,age*3& Total*:

  • 8/13/2019 GSM BTS3900 Onsite Engineer Operation Guide-20080728-IsSUE1.0

    25/25

    GSM BTS3900 Onsite Engineer Operation Guide Internal

    6ttac,ment

    1e$erence and ,ath $or -ownloading

    # BTS3900 5uic% Installation Guide AD300100K0*

    * BTS3900 GSM ,roduct -escription AD300100K03

    3 BTS3900 GSM Hardware -escription AD300100K03

    / BTS3900 GSM Co((issioning Guide AD300100K03

    Pat,7-ocu(entation 6J @ireless ,roduct ine 6J GSM6BSS 6J GSM6BTS 6J

    ,roduct Manual 6J BTS3900 GSM 6J D300100

    8 GSM H!@EI BTS3900 -eplo)(ent Guide6D#.0

    Pat,7-ocu(entation 6J @ireless ,roduct ine 6J GSM6BSS 6J GSM6BTS 6J

    Technical Guide 6J -eplo)(ent Guide

    : H!@EI EM! ser Guide6AD#00100#K0:

    Pat,7 -ocu(entation 6J @ireless ,roduct ine 6J @ireless ,u'lic 6J @ireless

    ,u'lic ,roducts 6J ,roduct Manual 6J EM!

    *0#36##6*? H!@EI Con$idential ,age*/& Total*:

    http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329265&doc_type=null&p_line=29-7http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329263&doc_type=null&p_line=29-7http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329262&doc_type=null&p_line=29-7http://support.huawei.com/support/DocView.do?doc_id=SE0000331566&doc_type=123-2http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329263&doc_type=null&p_line=29-7http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329262&doc_type=null&p_line=29-7http://support.huawei.com/support/DocView.do?doc_id=SE0000331566&doc_type=123-2http://support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=searchManualTableOfContents&node=000001380805&colID=ROOTENWEB%7CCO0000000173&web_doc_id=SE0000329265&doc_type=null&p_line=29-7