Goyen Series 4 Reverse Pulse Jet Pulse Valve. OVERVIEW.... 4 Series.
-
Upload
carley-spofford -
Category
Documents
-
view
236 -
download
7
Transcript of Goyen Series 4 Reverse Pulse Jet Pulse Valve. OVERVIEW.... 4 Series.
Goyen Series 4Reverse Pulse Jet Pulse Valve
OVERVIEW....4 Series
Application
The extremely rapid response, and very high flow rate delivered by the 4 Series diaphragm valves makes this product especially suitable for reverse pulse jet filter cleaning.
This high performance valve may be used for new dust collector builds or to replace existing ¾” and 1” valves in a dust collector refurbishment.
Application
Typical examples:-fabric filters-pleated filters-Panel filters-Manufacturing-Power generation-Mining-Resources-Steel and cement
FEATURES4 Series
No more spring failures!
Shockwave diaphragm Integrated spring.
Proprietary engineering thermoplastic elastomer blend for consistent performance throughout the temperature and pressure range.
Environmentally endurance tested at the extremes.
No spring failures!
1 Million Cycles guaranteed!
The coupling method of your choice
The classic Goyen dresser nut coupling design.
FS - Flange and Slide Seal
Threaded connections.
Nitrile or viton seals.
Threaded
Dresser nut
FS
Available with ¾” and 1” ports
Which repair kit? No problem!
Integral kit markings The 4 Series valve is marked with the appropriate diaphragm replacement kit part number.
No more searching catalogues or calling to find the right kit. Simple!
2-in-1: Integral or remote solenoid. Using the RCA3PV Series, or
RCA3DM Series pilots, the 4 Series valves can be easily configured for integral piloting.
RCA3PV: DIN connections, ATEX options, CE, Low Cost.
RCA3DM: Goyen Q Coil voltage and connection type range with CSA*
RCA3PV
RCA3DM
* CSA from June 15, 2012
QUALITY4 Series
QUALITY
Made inAustralia
ISO9001Design &
Manufacture
100%pressure &leak tested.
Performancetested across
pressure range
EnvironmentallyTested at
-40ºC to 82ºC(Shockwave)
Designedto
perform!
QUALITY
Made inAustralia
ISO9001Design &
Manufacture
100%pressure &leak tested.
Performancetested across
pressure range
EnvironmentallyTested at
-40ºC to 82ºC(Shockwave)
Designedto
perform!
15 – 40% higher peak pressure than equivalent older ‘2’ Series models.
Consistent pulse profile, regardless of pressure.
Quality starts with Design...
QUALITY
Made inAustralia
ISO9001Design &
Manufacture
100%pressure &leak tested.
Performancetested across
pressure range
EnvironmentallyTested at
-40ºC to 82ºC(Shockwave)
Designedto
perform!
World class manufacturing facility,
Quality Systems certified and audited to international standards for design and manufacture.
Each valve fully checked for operation and sealing performance.
... And then includes execution.
DIMENSIONS RCAC25 & RCAC20 MODELS
4 Series
Dimensions in mm [inches]
RCAC25DD4: RCAC20DD4:
Dimensions in mm [inches]
RCAC25T4: RCAC20T4: RCAC20ST4:
Dimensions in mm [inches]
RCAC25FS4: RCAC20FS4:
DIMENSIONS RCA3PV & RCA3DM PILOT MODULES
4 Series
Dimensions in mm [inches]
RCA3PV RCA3DM
PERFORMANCE4 Series
Kv and Cv values
INSTALLATION REQUIREMENTS4 Series
Operating Conditions
Metric US/Imperial
Supply compressed air pressure range
0.3 to 8.6 Bar 4.35 to 124.7 PSI
Compressed air temperature(Shockwave diaphragms)
-40ºC to 82ºC -40ºF to 180ºF
Compressed air temperature(Viton diaphragms)
-40ºC to 232ºC -40ºF to 450ºF
Media type Air or inert gases only.
Remote pilot connections Minimum pilot tube bore: 4mm (0.16”)Maximum length: 2m (79”)
HOW TO ORDERRCAC25 & RCAC20 MODELS
4 Series
RCAC20 __ __ __
Diaphragm type: 1 – Viton2 – Shockwave
Pilot Port : 0 – NPT Thread 1 – Rc
2 – G
Pilot Port : 0 – 1/8” Size 1 – 1/4”
¾” Valves
The ‘4’ means this is a fourth generation pulse jet valve.
__
Inlet/Outlet style: T4 – ThreadedST4 – Stub Thread
DD4 – Dresser nut
FS4 – Flange in/ Slide Seal out
RCAC25 __ __ __
Diaphragm type: 1 – Viton2 – Shockwave
Pilot Port : 0 – NPT Thread 1 – Rc
2 – G
Pilot Port : 0 – 1/8” Size 1 – 1/4”
1” Valves
The ‘4’ means this is a fourth generation pulse jet valve.
__
Inlet/Outlet style: T4 – Threaded
DD4 – Dresser nut
FS4 – Flange in/ Slide Seal out
HOW TO ORDERPILOT MODULES
4 Series
RCA3PV integral pilot:
RCA3DM integral pilot:
RCA3DM solenoid choices:
SERVICINGRCAC25DD4 Series
Repair kit detailsDiaphragm replacement kit numbers are marked on the diaphragm, visible before disassembly.
Shockwave assembly
Viton assembly
Valve & Pilot service kit codesValve model Shockwave Viton Nitrile
RCAC20T4RCAC20ST4
K2034 K2033 N/A
RCAC20DD4DRESSER SEAL KIT
K2034N/A
K2033K2009
N/AK2008
RCAC20FS4OUTLET SEAL
K2034N/A
K2033G690338-2
N/AG690338
RCAC25T4 K2546 K2551 N/A
RCAC25DD4DRESSER SEAL KIT
K2546N/A
K2551K2507
N/AK2508
RCAC25FS4OUTLET SEAL
K2546N/A
K2551G690763-2
N/AG690763
RCA3DM N/S K0384 K0380
APPROVALSRCAC25DD4 Series
Approvals Under the treaty of establishing the European Economic Community, the council of European Communities adopted into law a series of directives to harmonize technical standards.
The 4 series valves are controlled by
When used in combination with Goyen or Mecair solenoids, these valves are also controlled by
The Goyen 4 Series valves and its compatible Goyen solenoid pilots comply with these directives, and bear the CE approval mark on the solenoid and/or valve cover.
Council Directive #
Machinery 89/392/EEC
PED 97/23/EC
Council Directive #
EMC 89/336/EEC
Low Voltage 72/23/EEC
European Directive (CE)
Approvals The Goyen 4 series may be used with any of the Goyen or Mecair remote pilot enclosures.
These enclosures include products with UL, CSA, and ATEX certifications to meet the applications of
CSA:
Class I, Group D
Class II, Groups E, F, G
UL:
Class I, Group D
Class II, Groups E, F, G
ATEX:
II 2 G D (Ex d IIB T3 Gb)
II 2 G D (Ex d IIB T6 Gb)
Please refer to the Goyen or Mecair literature for further information on these enclosures.
Hazardous areas
Goyen Series 4Reverse Pulse Jet Pulse Valve