Golden DRAGON Plus Datasheet Version 1.1 LD...
Transcript of Golden DRAGON Plus Datasheet Version 1.1 LD...
2013-06-19
Golden DRAGON PlusDatasheetVersion 1.1
LD W5AM
2013-06-19 1
Lichtausbeute: typ. 49 lm/W
This Golden DRAGON® family member allows the design of small size high brightness light sources, while meeting highest lifetime requirements.
Dieses Mitglied der Golden-DRAGON®-Familie ermöglicht die Entwicklung kleiner und dennoch heller Lichtquellen - unter höchsten Ansprüchen an deren Lebenserwartung.
Features: Besondere Merkmale: • Package: white SMT package with clear silicone
lens, chip level conversion• Gehäusetyp: white SMT package with clear
silicone lens, chip level conversion• Technology: ThinGaN • Technologie: ThinGaN • Viewing angle at 50 % IV: 170° • Abstrahlwinkel bei 50 % IV: 170°• Color: deep blue (455 nm) • Farbe: deep blue (455 nm)• Radiant Efficiency: typ. 40 % • Lichtausbeute: typ. 40 %• Radiant Flux : typ. 453 mW
• Strahlungsfluss: typ. 453 mW
Applications Anwendungen• Backlighting (switches, keys, displays, illuminated
advertising, general lighting...)• Hinterleuchtung (LCD, Handy, Schalter, Tasten,
Displays, Werbebeleuchtung, Allgemeinbeleuchtung)
• Architectural lighting • Architekturbeleuchtung• Marker lights (e.g. steps, exit ways, etc.) • Markierungsbeleuchtnung (z.B. Stufen,
Fluchtwege, etc.)• Flood light and wall washers • Flutlichter und Wandfluter• Beacons and warning lights • Blitz- und Warnleuchten
Version 1.1 LD W5AM
Ordering InformationBestellinformationType: Radiant Power 1) page 20 Ordering CodeTyp: Strahlungsleistung 1) Seite 20 Bestellnummer
IF = 350 mAΦE [mW]
LD W5AM-1U4U-35 450 ... 710 Q65111A3454LD W5AM-4T2U-35 400 ... 560 Q65111A3453
Note: The above Type Numbers represent the order groups which include only a few brightness groups (see page 5). Only one group will be shipped on each packing unit (there will be no mixing of two groups on each packing unit). E. g. LD W5AM-4T2U-35 means that only one group 1U, 2U, 4T will be shippable for any packing unit. In order to ensure availability, single brightness groups will not be orderable.In a similar manner for colors where wavelength groups are measured and binned, single wavelength groups will be shipped on any one packing unit. E. g. LD W5AM-4T2U-35 means that only one wavelength group 3,4,5 will be shippable. LD W5AM-4T2U-35 means that the device will be shipped within the specified limits as stated on page 5In order to ensure availability, single wavelength groups will not be orderable (see page 5).
Anm.: Die oben genannten Typbezeichnungen umfassen die bestellbaren Selektionen. Diese bestehen aus wenigen Helligkeitsgruppen (siehe Seite 5). Es wird nur eine einzige Helligkeitsgruppe pro Verpackungseinheit geliefert. Z. B. LD W5AM-4T2U-35 bedeutet, dass in einer Verpackungseinheit nur eine der Helligkeitsgruppen 1U, 2U, 4T enhalten ist. Um die Liefersicherheit zu gewährleisten, können einzelne Helligkeitsgruppen nicht bestellt werden.Gleiches gilt für die Farben, bei denen Wellenlängengruppen gemessen und gruppiert werden. Pro Verpackungseinheit wird nur eine Wellenlängengruppe geliefert. Z. B. LD W5AM-4T2U-35 bedeutet, dass in einer Verpackungseinheit nur eine der Wellenlängengruppen 3,4,5 enthalten ist (siehe Seite 5). LD W5AM-4T2U-35 bedeutet, dass das Bauteil innerhalb der spezifizierten Grenzen geliefert wird. Um die Liefersicherheit zu gewährleisten, können einzelne Wellenlängengruppen nicht bestellt werden.
2013-06-19 2
Version 1.1 LD W5AM
Maximum RatingsGrenzwerteParameter Symbol Values UnitBezeichnung Symbol Werte EinheitOperating temperature rangeBetriebstemperatur
Top -40 ... 125 °C
Storage temperature rangeLagertemperatur
Tstg -40 ... 125 °C
Junction temperature for short time applications *Sperrschichttemperatur für Kurzzeitanwendung *
Tj 175 °C
Junction temperatureSperrschichttemperatur
Tj 135 °C
Forward currentDurchlassstrom(TS = 25 °C)
IF 20 ... 1000 mA
Surge currentStoßstrom(t <= 10 μs; D = 0.005; TS = 25 °C)
IFM 2500 mA
Reverse voltageSperrspannung(TS = 25 °C)
VR not designed for reverse operation
V
ESD withstand voltageESD Festigkeit(acc. to ANSI/ESDA/JEDEC JS-001 - HBM, Class 3B)
VESD 8 kV
Note: *The LED chip exhibits excellent performance but slight package discoloration occurs at highest temperatures. Exemplary median lifetime for Tj = 175°C is 100h.
Anm: *Auch bei höchsten Temperaturen zeigt der LED Chip sehr gute Leistungsmerkmale, aber es kann eine leichte Verfärbung des Gehäuses auftreten. Die mittlere Lebensdauer bei Tj = 175°C beträgt 100h.
2013-06-19 3
Version 1.1 LD W5AM
Characteristics (TS = 25 °C; IF = 350 mA)KennwerteParameter Symbol Values UnitBezeichnung Symbol Werte EinheitWavelength at peak emissionWellenlänge d. emittierten Lichtes
(typ.) λpeak 451 nm
Dominant Wavelength 2) page 20
Dominantwellenlänge 2) Seite 20 (min.)(typ.)(max.)
λdomλdomλdom
449455461
nmnmnm
Spectral bandwidth at 50% Irel maxSpektrale Bandbreite b. 50% Irel max
(typ.) Δλ 20 nm
Viewing angle at 50 % IVAbstrahlwinkel bei 50 % IV
(typ.) 2ϕ 170 °
Forward voltage 3) page 20
Durchlassspannung 3) Seite 20 (min.)(typ.)(max.)
VFVFVF
2.703.203.70
VVV
Reverse currentSperrstrom
IR not designed for reverse operation
Thermal resistance junction / solder point 4) page 20
Wärmewiderstand Sperrschicht / Lötpad 4) Seite 20
(typ.)(max.)
Rth JS Rth JS
6.511
K/WK/W
2013-06-19 4
Version 1.1 LD W5AM
Brightness GroupsHelligkeitsgruppen
Dominant Wavelength Groups 2) page 20
Dominant Wellenlängengruppen 2) Seite 20
Group Radiant Power 1) page 20 Radiant Power 1) page 20
Gruppe Strahlungsleistung 1) Seite 20 Strahlungsleistung 1) Seite 20
(min.) ΦE [mW] (max.) ΦE [mW]3T 355 4004T 400 4501U 450 5002U 500 5603U 560 6304U 630 710
Note: The standard shipping format for serial types includes either a lower family group, an upper family group or a grouping of all individual brightness groups of only a few brightness groups. Individual brightness groups cannot be ordered.
Anm.: Die Standardlieferform von Serientypen beinhaltet entweder eine untere Familiengruppe, eine obere Familiengruppe oder eine Sammelgruppe, die aus nur wenigen Helligkeitsgruppen besteht. Einzelne Helligkeitsgruppen sind nicht bestellbar.
Group deep blueGruppe (min.) λdom
[nm](max.) λdom [nm]
3 449 4534 453 4575 457 461
Note: No packing unit / tape ever contains more than one color group for each selection.Anm.: In einer Verpackungseinheit / Gurt ist immer nur eine Gruppe für jede Farbe enthalten.
2013-06-19 5
Version 1.1 LD W5AM
Group Name on LabelGruppenbezeichnung auf EtikettExample: 3U-3Beispiel: 3U-3BrightnessHelligkeit
WavelengthWellenlänge
3U 3
Note: No packing unit / tape ever contains more than one group for each selection.Anm.: In einer Verpackungseinheit / Gurt ist immer nur eine Gruppe für jede Selektion enthalten.
2013-06-19 6
Version 1.1 LD W5AM
Relative Spectral Emission - V(λ) = Standard eye response curve 5) page 20
Relative spektrale Emission - V(λ) = spektrale Augenempfindlichkeit 5) Seite 20
Φrel = f (λ); TS = 25 °C; IF = 350 mA
Radiation Characteristics 5) page 20
Abstrahlcharakteristik 5) Seite 20
Irel = f (ϕ); TS = 25 °C
OHL06115
350 400 450 500 550 600 650 700 750 8000.0
0.2
0.4
0.6
0.8
1.0
λ (nm)
: : V
(deep blue)Φrel
λ
Φrel
OHL03635
0˚ 20˚ 40˚ 60˚ 80˚ 100˚ 120˚0.40.60.81.0100˚
90˚
80˚
70˚
60˚
50˚
0˚10˚20˚30˚40˚
0
0.2
0.4
0.6
0.8
1.0ϕ
2013-06-19 7
Version 1.1 LD W5AM
Forward Current 5) page 20
Durchlassstrom 5) Seite 20
IF = f (VF); TS = 25 °C
Relative Radiant Power 5) page 20 , 6) page 20
Relative Strahlungsleistung 5) Seite 20 , 6) Seite 20
ΦE/ΦE(350 mA) = f(IF); TS = 25 °C
Dominant Wavelength 5) page 20
Dominante Wellenlänge 5) Seite 20
λpeak = f(IF); TS = 25 °C
OHL06007
2.8 3.0 3.2 3.4 3.6
200
400
600
800
1000I (mA)F
V (V)F
50
OHL06044
200
400
600
800
1000
0.0
0.5
1.0
1.5
2.0
2.5
I (mA)F
ΦE
ΦE (350 mA)
OHL04436
IF
0-6
mA
Δλdomnm
200 400 600 1000
-4
-2
0
2
4
6
2013-06-19 8
Version 1.1 LD W5AM
Relative Forward Voltage 5) page 20
Relative Vorwärtsspannung 5) Seite 20
ΔVF = VF - VF(25°C) = f(Tj); IF = 350 mA
Relative Radiant Power 5) page 20
Relative Strahlungsleistung 5) Seite 20
ΦE/ΦE(25 °C) = f(Tj); IF = 350 mA
Dominant Wavelength 5) page 20
Dominante Wellenlänge 5) Seite 20
λdom = f(Tj); IF = 350 mA
OHL06027
-40 -20 0 20 40 60 80 100120Tj (°C)
-0.3
-0.2
-0.1
0.0
0.1
0.2
0.3ΔVF (V)
(°C)
OHL06148
-40 -20 0 20 40 60 80 100 120T j
0.0
0.2
0.4
0.6
0.8
1.0
1.2ΦE
ΦE(25°C )
OHL04441
-6
Δλdomnm
jT-40 200-20 806040 ˚C 120
-4
-2
0
2
4
6
2013-06-19 9
Version 1.1 LD W5AM
Max. Permissible Forward CurrentMax. zulässiger DurchlassstromIF = f (T)
Permissible Pulse Handling CapabilityZulässige Impulsbelastbarkeit IF = f(tp)D: Duty cycle, TS = 25 °C
Permissible Pulse Handling CapabilityZulässige Impulsbelastbarkeit IF = f(tp)D: Duty cycle, TS = 85 °C
80
Do not use current below 100 mA
0
200
100
0
500
300
400
604020
800
600
700
1000
900
FI (mA)
130100T (°C)S
OHL04372
0.8-5
FIA
tp
s
OHL04374
-410 -310 -210 -110 010 110 21010
Pt=D TT
tP
IF
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
0.51
0.010.020.050.10.2
0.005D =
0.8-5
FIA
tp
s
OHL04374
-410 -310 -210 -110 010 110 21010
Pt=D TT
tP
IF
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
0.51
0.010.020.050.10.2
0.005D =
2013-06-19 10
Version 1.1 LD W5AM
Package Outline 7) page 20
Maßzeichnung 7) Seite 20
Approximate Weight: 250 mg
2013-06-19 11
Version 1.1 LD W5AM
Gewicht: 250 mgMark: CathodeMarkierung: KathodeESD information: LED is protected by ESD device which is connected
in parallel to LED-Chip.ESD Information: Die LED enthält ein ESD-Bauteil, das parallel zum
Chip geschalten ist. Corrosion robustness better than EN 60068-2-60 (method 4):with enhanced corrosion test: 40°C / 90%rh / 15ppm H2S / 336 h Korrosionsfestigkeit besser als EN 60068-2-60 (method 4):mit erweitertem Korrosionstest: 40°C / 90%rh / 15ppm H2S / 336 h
2013-06-19 12
Version 1.1 LD W5AM
Recommended Solder Pad 7) page 20 Reflow solderingEmpfohlenes Lötpaddesign 7) Seite 20 Reflow-Löten
Solder resist
Bare CopperFreies Kupfer
Lötpasten SchabloneSolder paste stencil
Lötstopplack
OHPY3637
1 (0
.039
)
KupferCopper
1.6 (0.063)
11.6 (0.457)
12.0 (0.472)
2.3
(0.0
91)
2.3
(0.0
91)
12.0
(0.4
72)
1.6 (0.063)
11.6 (0.457)
3 Lötstellen3 solder points Thermal enhanced PCB
Thermisch optimiertes PCB
ø4.0 (0.157)Heatsink attach
ø4.0 (0.157)
ø2.5 (0.098)
1 (0.039)
Attention:Anode andHeatsink areelectricallyconnected
Achtung:Anode undHeatsink sindelektrischverbunden
2013-06-19 13
Version 1.1 LD W5AM
Reflow Soldering ProfileReflow-LötprofilPreconditioning: JEDEC Level 2 acc. to JEDEC J-STD-020D.01
00
s
OHA04525
50
100
150
200
250
300
50 100 150 200 250 300t
T
˚C
St
t
Pt
Tp240 ˚C
217 ˚C
245 ˚C
25 ˚C
L
OHA04612
Profile FeatureProfil-Charakteristik
Ramp-up rate to preheat*)
25 °C to 150 °C2 3 K/s
Time tS TSmin to TSmax
tS
tL
tP
TL
TP
100 12060
10 20 30
80 100
217
2 3
245 260
3 6
Time25 °C to TP
Time within 5 °C of the specified peaktemperature TP - 5 K
Ramp-down rate*TP to 100 °C
All temperatures refer to the center of the package, measured on the top of the component* slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range
Ramp-up rate to peak*)
TSmax to TP
Liquidus temperature
Peak temperature
Time above liquidus temperature
SymbolSymbol
UnitEinheit
Pb-Free (SnAgCu) Assembly
Minimum MaximumRecommendation
K/s
K/s
s
s
s
s
°C
°C
480
2013-06-19 14
Version 1.1 LD W5AM
Tape and ReelGurtverpackung24 mm tape with 200 pcs. on ∅ 180 mm reel, 1200 pcs. on ∅ 330 mm reel
Tape dimensions in mm (inch)Tape dimensions in mm ( inch)
Reel dimensions in mm (inch) Reel dimensions in mm ( inch)
Reel dimensions in mm ( inch)
W P0 P1 P2 D0 E F24 +0.3/-0.1 4 ± 0.1
(0.157 ± 0.004)
8 ± 0.1(0.315 ± 0.004)or12 ± 0.1(0.472 ± 0.004)
2 ± 0.1(0.079 ± 0.004)
1.5 ± 0.1(0.059 + 0.004)
1.75 ± 0.1(0.069 ± 0.004)
11.5 ± 0.05(0.453 ± 0.004)
A W Nmin W1 W2max180 (7) 24 (0.945) 60 (2.362) / 100
(3.937)24.4 + 2 (0.646 + 0.079)
30.4 (1.197)
A W Nmin W1 W2max330 (13) 24 (0.945) 60 (2.362) / 100
(3.937)24.4 + 2 (0.646 + 0.079)
30.4 (1.197)
D0
2P
P0
1P
WFE
Direction of unreeling
N
W1
2W
A
OHAY0324
Label
Leader:Trailer:
13.0
Direction of unreeling
±0.2
5
min. 160 mm *min. 400 mm *
*) Dimensions acc. to IEC 60286-3; EIA 481-D
2013-06-19 16
Version 1.1 LD W5AM
Barcode-Product-Label (BPL)Barcode-Produkt-Etikett (BPL)
Dry Packing Process and MaterialsTrockenverpackung und Materialien
Note: Moisture-sensitive product is packed in a dry bag containing desiccant and a humidity card. Regarding dry pack you will find further information in the internet and in the Short Form Catalog in chapter “Tape and Reel” under the topic “Dry Pack”. Here you will also find the normative references like JEDEC.
Anm.: Feuchteempfindliche Produkte sind verpackt in einem Trockenbeutel zusammen mit einem Trockenmittel und einer Feuchteindikatorkarte. Bezüglich Trockenverpackung finden Sie weitere Hinweise im Internet und in unserem Short Form Catalog im Kapitel “Gurtung und Verpackung” unter dem Punkt “Trockenverpackung”. Hier sind Normenbezüge, unter anderem ein Auszug der JEDEC-Norm, enthalten.
OHA04563
(G) GROUP:
1234567890(1T) LOT NO: (9D) D/C: 1234
(X) PROD NO: 123456789
(6P) BATCH NO: 1234567890
LX XXXX
RoHS Compliant
BIN1: XX-XX-X-XXX-X
ML2
Temp ST260 °C R
Pack: R18
DEMY 022
B_R999_1880.1642 R
9999(Q)QTY:
SemiconductorsOSRAM Opto
XX-XX-X-X
OHA00539
OSRAM
Moisture-sensitive label or print
Barcode label
Desiccant
Humidity indicator
Barcode label
OSRAM
Please check the HIC immidiately afterbag opening.
Discard if circles overrun.Avoid metal contact.
WET
Do not eat.
Comparatorcheck dot
parts still adequately dry.
examine units, if necessary
examine units, if necessary
5%
15%
10%bake units
bake units
If wet,
change desiccant
If wet,
Humidity IndicatorMIL-I-8835
If wet,
Mois
ture
Level 3
Flo
or tim
e 168 H
ours
Mois
ture
Level 6
Flo
or tim
e 6
Hours
a) H
umid
ity In
dicato
r C
ard is
> 1
0% w
hen read a
t 23 ˚
C ±
5 ˚C
, or
reflo
w, v
apor-phase r
eflow
, or equiv
alent p
rocessin
g (peak p
ackage
2. Afte
r th
is b
ag is o
pened, devic
es that w
ill b
e subje
cted to
infrare
d
1. Shelf
life in
seale
d bag: 2
4 month
s at <
40 ˚
C a
nd < 9
0% rela
tive h
umid
ity (R
H).
Mois
ture
Level 5
a
at facto
ry c
onditions o
f
(if b
lank, s
eal date
is id
entical w
ith d
ate c
ode).
a) M
ounted w
ithin
b) S
tore
d at
body tem
p.
3. Devic
es require
bakin
g, befo
re m
ounting, i
f:
Bag s
eal date
Mois
ture
Level 1
Mois
ture
Level 2
Mois
ture
Level 2
a4. If b
aking is
require
d,
b) 2a o
r 2b is
not m
et.
Date
and ti
me o
pened:
refe
rence IP
C/J
ED
EC
J-S
TD
-033 fo
r bake p
rocedure
.
Flo
or tim
e see b
elow
If bla
nk, see b
ar code la
bel
Flo
or tim
e > 1
Year
Flo
or tim
e 1
Year
Flo
or tim
e 4
Weeks10%
RH
.
_<
Mois
ture
Level 4
Mois
ture
Level 5
˚C).
OPTO
SEM
ICO
NDUCTORS
MO
ISTURE S
ENSITIV
E
This b
ag conta
ins
CAUTION
Flo
or tim
e 72 H
ours
Flo
or tim
e 48 H
ours
Flo
or tim
e 24 H
ours
30 ˚C
/60%
RH
.
_<
LE
VE
L
If bla
nk, see
bar code la
bel
2013-06-19 17
Version 1.1 LD W5AM
Transportation Packing and MaterialsKartonverpackung und Materialien
Dimensions of transportation box in mm (inch)Width / Breite Length / Länge Height / Höhe195 ± 5 (7.677 ± 0.1968) 349 ± 5 (13.740 ± 0.196)
195 ± 5 (7.677 ± 0.1968) 349 ± 5 (13.740 ± 0.196)
42 ± 5 (1.653 ± 0.196) 38 ± 5 (1.496 ± 0.196
Notes HinweiseThe evaluation of eye safety occurs according to the standard IEC 62471:2008 ("photobiological safety of lamps and lamp systems"). Within the risk grouping system of this CIE standard, the LED specified in this data sheet fall into the class Moderate risk (exposure time 0.25 s). Under real circumstances (for exposure time, eye pupils, observation distance), it is assumed that no endangerment to the eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential due to their blinding effect. As is also true when viewing other bright light sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irritation, annoyance, visual impairment, and even accidents, depending on the situation.
Die Bewertung der Augensicherheit erfolgt nach dem Standard IEC 62471:2008 ("photobiological safety of lamps and lamp systems"). Im Risikogruppensystem dieser CIE- Norm erfüllen die in diesem Datenblatt angegebenen LEDs folgende Gruppenanforderung - Moderate risk (Expositionsdauer 0,25 s). Unter realen Umständen (für Expositionsdauer, Augenpupille, Betrachtungsabstand) geht damit von diesen Bauelementen keinerlei Augengefährdung aus. Grundsätzlich sollte jedoch erwähnt werden, dass intensive Lichtquellen durch ihre Blendwirkung ein hohes sekundäres Gefahrenpotenzial besitzen. Nach einem Blick in eine helle Lichtquelle (z.B. Autoscheinwerfer), kann ein temporär eingeschränktes Sehvermögen oder auch Nachbilder zu Irritationen, Belästigungen, Beeinträchtigungen oder sogar Unfällen führen.
OHA02044
PACKVAR:
R077Additional TEXT
P-1+Q-1
Multi TOPLED
Muste
r
OSRAM Opto
Semiconductors
(6P) BATCH NO:
(X) PROD NO:
10
(9D) D/C:
11(1T) LOT NO:
210021998
123GH1234
024 5
(Q)QTY: 2000
0144
(G) GROUP:
260 C RT240 C R
3
220 C R
MLBin3:Bin2: Q
-1-20
Bin1: P-1-20
LSY T6762
2a
Temp ST
R18DEMY
PACKVAR:
R077Additional TEXT
P-1+Q-1
Multi TOPLED
Muste
r
OSRAM Opto
Semiconductors
(6P) BATCH NO:
(X) PROD NO:
10
(9D) D/C:
11(1T) LOT NO:
210021998
123GH1234
024 5
(Q)QTY: 2000
0144
(G) GROUP:
260 C RT240 C R
3
220 C R
MLBin3:Bin2: Q
-1-20
Bin1: P-1-20
LSY T6762
2a
Temp ST
R18DEMY
OSRAM
Packing
Sealing label
Barcode label
Mois
ture
Level 3
Flo
or tim
e 168 H
ours
Mois
ture
Level 6
Flo
or tim
e 6
Hours
a) H
umid
ity In
dicato
r C
ard is
> 1
0% w
hen read a
t 23 ˚
C ±
5 ˚C
, or
reflo
w, v
apor-phase r
eflow
, or equiv
alent p
rocessin
g (peak p
ackage
2. Afte
r th
is b
ag is o
pened, devic
es that w
ill b
e subje
cted to
infrare
d
1. Shelf
life in
seale
d bag: 2
4 month
s at <
40 ˚
C a
nd < 9
0% rela
tive h
umid
ity (R
H).
Mois
ture
Level 5
a
at facto
ry c
onditions o
f
(if b
lank, s
eal date
is id
entical w
ith d
ate c
ode).
a) M
ounted w
ithin
b) S
tore
d at
body tem
p.
3. Devic
es require
bakin
g, befo
re m
ounting, i
f:
Bag s
eal date
Mois
ture
Level 1
Mois
ture
Level 2
Mois
ture
Level 2
a4. If b
aking is
require
d,
b) 2a o
r 2b is
not m
et.
Date
and ti
me o
pened:
refe
rence IP
C/J
ED
EC
J-S
TD
-033 fo
r bake p
rocedure
.
Flo
or tim
e see b
elow
If bla
nk, see b
ar code la
bel
Flo
or tim
e > 1
Year
Flo
or tim
e 1
Year
Flo
or tim
e 4
Weeks10%
RH
.
_<
Mois
ture
Level 4
Mois
ture
Level 5
˚C).
OPTO
SEM
ICO
NDUCTORS
MO
ISTURE S
ENSITIV
E
This b
ag conta
ins
CAUTION
Flo
or tim
e 72 H
ours
Flo
or tim
e 48 H
ours
Flo
or tim
e 24 H
ours
30 ˚C
/60%
RH
.
_<
LE
VE
L
If bla
nk, see
bar code la
bel
Barcode label
2013-06-19 18
Version 1.1 LD W5AM
Disclaimer DisclaimerAttention please!The information describes the type of component and shall not be considered as assured characteristics.Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet.PackingPlease use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred.Components used in life-support devices or systems must be expressly authorized for such purpose!Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS.
*) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system.**) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.
Bitte beachten!Lieferbedingungen und Änderungen im Design vorbehalten. Aufgrund technischer Anforderungen können die Bauteile Gefahrstoffe enthalten. Für weitere Informationen zu gewünschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet.VerpackungBenutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nächstgelegene Vertriebsbüro. Wir nehmen das Verpackungsmaterial zurück, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Für Verpackungsmaterial, das unsortiert an uns zurückgeschickt wird oder das wir nicht annehmen müssen, stellen wir Ihnen die anfallenden Kosten in Rechnung.Bauteile, die in lebenserhaltenden Apparaten und Systemen eingesetzt werden, müssen für diese Zwecke ausdrücklich zugelassen sein!Kritische Bauteile* dürfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverständnis von OSRAM OS vorliegt.
*) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems führen wird oder die Sicherheit oder Effektivität dieses Apparates oder Systems beeinträchtigt.**) Lebenserhaltende Apparate oder Systeme sind für (a) die Implantierung in den menschlichen Körper oder (b) für die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist.
2013-06-19 19
Version 1.1 LD W5AM
Glossary Glossar1) Brightness: Brightness values are measured during
a current pulse of typically 25 ms, with an internal reproducibility of +/- 8 % and an expanded uncertainty of +/- 11 % (acc. to GUM with a coverage factor of k = 3).
1) Helligkeit: Helligkeitswerte werden während eines Strompulses einer typischen Dauer von 25 ms, mit einer internen Reproduzierbarkeit von +/- 8 % und einer erweiterten Messunsicherheit von +/- 11 % gemessen (gemäß GUM mit Erweiterungsfaktor k = 3).
2) Wavelength: The wavelength is measured at a current pulse of typically 25 ms, with an internal reproducibility of ± 0,5 nm and an expanded uncertainty of ± 1 nm (acc. to GUM with a coverage factor of k=3).
2) Wellenlänge: Die Wellenläge wird während eines Strompulses einer typischen Dauer von 25 ms, mit einer internen Reproduzierbarkeit von ± 0,5 nm und einer erweiterten Messunsicherheit von ± 1 nm gemessen (gemäß GUM mit Erweiterungsfaktor k=3).
3) Forward Voltage: The forward voltage is measured during a current pulse of typically 8 ms, with an internal reproducibility of +/- 0,05 V and an expanded uncertainty of +/- 0,1 V (acc. to GUM with a coverage factor of k=3).
3) Durchlassspannung: Vorwärtsspannungen werden während eines Strompulses einer typischen Dauer von 8 ms, mit einer internen Reproduzierbarkeit von +/- 0,05 V und einer erweiterten Messunsicherheit von +/- 0,1 V gemessen (gemäß GUM mit Erweiterungsfaktor k=3).
4) Thermal Resistance: Rth max is based on statistic values (6σ)
4) Wärmewiderstand: Rth max basiert auf statistischen Werten (6σ)
5) Typical Values: Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice.
5) Typische Werte: Wegen der besonderen Prozessbedingungen bei der Herstellung von LED können typische oder abgeleitete technische Parameter nur aufgrund statistischer Werte wiedergegeben werden. Diese stimmen nicht notwendigerweise mit den Werten jedes einzelnen Produktes überein, dessen Werte sich von typischen und abgeleiteten Werten oder typischen Kennlinien unterscheiden können. Falls erforderlich, z.B. aufgrund technischer Verbesserungen, werden diese typischen Werte ohne weitere Ankündigung geändert.
6) Relative Brightness Curve: In the range where the line of the graph is broken, you must expect higher brightness differences between single LEDs within one packing unit.
6) Relative Helligkeitskurve: Im gestrichelten Bereich der Kennlinien muss mit erhöhten Helligkeitsunterschieden zwischen Leuchtdioden innerhalb einer Verpackungseinheit gerechnet werden.
7) Tolerance of Measure: Dimensions are specified as follows: mm (inch).
7) Maßtoleranz: Maße werden wie folgt angegeben: mm (inch).
2013-06-19 20