GETTING STARTED - lancecamper.com · GETTING STARTED Travel Lock Out Loading Floor Plan on Device...
2
™ GETTING STARTED Travel Lock Out Loading Floor Plan on Device Connecting the DC to the BCM www.asaelectronics.com/incommand Get the app Download the iN•Command® app to turn your mobile device into the definitive RV Controller. The iN•Command® system is comprised of two parts, the DC (Display Commander or touch pad) and the BCM (Body Control Module or main control board). To turn on the DC, hold the power button until the screen flashes. When the DC is on, the Passcode screen will appear. Enter a four-digit code you will remember. Re-enter this passcode to “confirm”. This passcode will allow access into the iN•Command® interface to change and/or monitor multiple functions of the RV. The DC should then connect to the BCM, and the HOME screen will display. HOME screen Error Settings Climate Triggers Generator Awnings Jacks Lights Electrical Slides Exterior Lights Water Pump Battery 14.4 V Security Lights Interior Lights Water Heater Gray 1 Fresh 1 Black 1 Black 2 Gray 2 Gray 3 Fuel 1 4 7 2 3 5 6 8 9 Enter passcode 1 4 7 2 3 5 6 8 9 Enter passcode iN•Command® is equipped with a Travel Lock Out feature to ensure certain system functions are unavailable during transit. When the Brake signal or the Tow signal is activated, iN•Command® will lock down all motorized functions. The DC and mobile devices will display “Travel Lock Engaged” and affected buttons will cease to activate. The lights, water pump, water heater, and sensors will continue to function. To turn the Travel Lock off, press DISENGAGE on the DC inside the RV once the brake signal terminates. Exterior Lights Water Pump Battery 14.4 V Security Lights Interior Lights Water Heater Gray 1 Fresh 1 Black 1 Black 2 Gray 2 Gray 3 Fuel Travel Lock Engaged Disengage Warning Travel lock engaged. Warning Dismiss Lights Voltage Climate Water Settings Bluetooth Edit Passcode Global Connect™ Floor Plan Floor Plan DC Sync Reset On the Home Page of the mobile app, select SETTINGS. Press the FLOOR PLAN button in the settings menu page. Press DC SYNC to load the floor plan configuration from the DC. The current settings will be lost/ replaced upon doing this. Floor Plan DC Sync … When syncing via Global Connect FloorPlan synchronizing… 86% Dismiss Progress When syncing via Bluetooth® Sync FloorPlan Success Dismiss Notification When syncing has completed.
Transcript of GETTING STARTED - lancecamper.com · GETTING STARTED Travel Lock Out Loading Floor Plan on Device...
™
™
GETTING STARTED
Trav
el Lo
ck O
utLo
adin
g Flo
or P
lan
on D
evice
Conn
ectin
g th
e DC t
o the
BCM
www.asaelectronics.com/incommand
Get the appDownload the iN•Command® app to turn your mobile device into the definitive RV Controller.
The iN•Command® system is comprised of two parts, the DC (Display Commander or touch pad) and the BCM (Body Control Module or main control board).
To turn on the DC, hold the power button until the screen flashes. When the DC is on, the Passcode screen will appear. Enter a four-digit code you will remember. Re-enter this passcode to “confirm”. This passcode will allow access into the iN•Command® interface to change and/or monitor multiple functions of the RV. The DC should then connect to the BCM, and the HOME screen will display.
HOME screen
Error
SettingsClimate TriggersGeneratorAwnings
JacksLights ElectricalSlides
ExteriorLights
WaterPump
Battery14.4 V
SecurityLights
InteriorLights
WaterHeater
Gray 1Fresh 1 Black 1 Black 2 Gray 2 Gray 3 Fuel
Cancel
1
4
7
0
2 3
5 6
8 9
Enter
Confirm passcode
Cancel
1
4
7
0
2 3
5 6
8 9
Enter
Enter passcode
Cancel
1
4
7
0
2 3
5 6
8 9
Enter
Confirm passcode
Cancel
1
4
7
0
2 3
5 6
8 9
Enter
Enter passcode
iN•Command® is equipped with a Travel Lock Out feature to ensure certain system functions are unavailable during transit. When the Brake signal or the Tow signal is activated, iN•Command® will lock down all motorized functions. The DC and mobile devices will display “Travel Lock Engaged” and affected buttons will cease to activate.
The lights, water pump, water heater, and sensors will continue to function.
To turn the Travel Lock off, press DISENGAGE on the DC inside the RV once the brake signal terminates.
ExteriorLights
WaterPump
Battery14.4 V
SecurityLights
InteriorLights
WaterHeater
Gray 1Fresh 1 Black 1 Black 2 Gray 2 Gray 3 Fuel
Travel Lock Engaged
Disengage
Warning
Travel lock engaged.
Warning
Dismiss
FuelTanks
LightsVoltage
ClimateWater
RV
Settings
Bluetooth
Edit
Passcode
Global Connect™
Floor Plan
RV
Floor Plan
DC Sync
Reset
RV
On the Home Page of the mobile app, select SETTINGS.
Press the FLOOR PLAN button in the settings menu page.
Press DC SYNC to load the floor plan configuration from the DC. The current settings will be lost/replaced upon doing this.
Floor Plan
DC Sync …
Reset
RV
When syncing via Global Connect
FloorPlan synchronizing…
86%
Dismiss
Progress
When syncing via Bluetooth®
Sync FloorPlan Success
Dismiss
Notification
When syncing has completed.
Pairi
ng an
iOS D
evice
Pairi
ng an
And
roid
Dev
ice
©Copyright 2018 ASA Electronics, LLCQRGINCOMMAND1218
MA-1809003-1RNOTE: Some features may not be available depending on installed factory options.
Patent # (D776,068) Patent # (D762,644)
Enable Bluetooth® in the system settings of the mobile device.
On the DC Home Page, select SETTINGS. Select the Bluetooth® tab. Select PAIRING to pair devices, as well as view devices that are currently paired. Press SCAN to begin scanning for unpaired devices.
Error
SettingsClimate TriggersGeneratorAwnings
JacksLights ElectricalSlides
ExteriorLights
WaterPump
Battery14.4 V
SecurityLights
InteriorLights
WaterHeater
Gray 1Fresh 1 Black 1 Black 2 Gray 2 Gray 3 Fuel
Bluetooth
Settings
Wi-Fi
Date & Time
Floor Plan
Edit
Passcode
Pairing
Settings > Bluetooth
Connected Devices
Select your mobile device by pressing it in the UNPAIRED DEVICES list. A popup with the device name will appear on the DC. Press PAIR. A Bluetooth® pairing request will appear on both the DC and mobile device. Press PAIR on both. The mobile device will be displayed in the PAIRED DEVICES list on the DC.
Paired Unpaired devices
My Mobile Device01:AB:23:CD:56:EF
My Mobile Device01:AB:23:CD:56:EF
NCSPDC12345AVisible to nearby devices
Settings > Bluetooth > Pairing
Scanning
Paired Unpaired devices
My Mobile Device01:AB:23:CD:56:EF
My Mobile Device01:AB:23:CD:56:EF
NCSPDC12345AVisible to nearby devices
Settings > Bluetooth > Pairing
Scanning
PAIRCANCEL
Bluetooth Request
My Mobile Device
Paired Unpaired devices
My Mobile Device01:AB:23:CD:56:EF
My Mobile Device01:AB:23:CD:56:EF
NCSPDC12345AVisible to nearby devices
Settings > Bluetooth > Pairing
Scanning
“NCSPDC12345A” would like to pair with your iPad. Confirm that
the code “912404” is shown on “NCSPDC12345A”.
FuelTanks
LightsVoltage
ClimateWater
RV
Settings
Bluetooth
Edit
Passcode
Global Connect™
Floor Plan
RV
Paired Devices:
RV
Scan Discover
Unpaired Devices:NCSPDC12345A01:AB:23:CD:56:EF
FuelTanks
LightsVoltage
ClimateWater
RV
Paired Devices:
RV
Scan Discover
Unpaired Devices:
NCSPDC12345A01:AB:23:CD:56:EF
On your mobile device using the iN•Command® app, select SETTINGS. Select the BLUETOOTH tab.
Press SCAN to start scanning for your Display Commander. Find your DC in the UNPAIRED DEVICES list. Select the DC by tapping on it’s name
A Bluetooth pairing request will appear on both your DC and mobile device. Press OK on your mobile device.
Your DC will be displayed in the PAIRED DEVICES list on the mobile app.
Bluetooth pairing request
CANCEL OK
Confirm passkey is XXXXXX to pair with NCSPDC12345A.
For owner’s manual and software updates please visithttps://www.in-command.net/control-systems.
For further assistance, please call 877-845-8750.Scan for
Owner’s Manualand other resources
![Skaffold - storage.googleapis.com · [getting-started getting-started] Hello world! [getting-started getting-started] Hello world! [getting-started getting-started] Hello world! 5.](https://static.fdocuments.net/doc/165x107/5ec939f2a76a033f091c5ac7/skaffold-getting-started-getting-started-hello-world-getting-started-getting-started.jpg)
