Genuine Accessories - hyundaipartsdeal.com · Genuine Accessories Electronic Installation...

Genuine Accessories

Electronic Installation Instructions

Glasses Gloves

Mask Hearing Protection

Part Weight (Gross) FMVSS 110 Compliance Information

Technical Support

1) Read the entire Installation Instructions prior to beginning the installation of the part.2) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.4) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.5) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.6) Record radio presets prior to disconnecting battery power, if needed.7) Ensure the transportation fuse is set to "ON" before starting the install, if applicable.8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.9) Vehicle should be at room temperature.10)

(B) Dealer Technician

Instructional Symbols / Definitions

M~F - 9am~5pm Pacific Standard TimeHours:

50/50 Isopropyl

Alcohol (70%) and

Water Mix

Notes to the installer:

10mm Deep Well

SocketTorque Wrench Trim Removal Tool Wire Cutters

Clean Cloth

Application Notes

Language English

1/2/2019Rev. Date

Accessory:Vehicle Model:

Difficulty stated above reflects the minimum level of

expertise required to install the accessory:

( B )

Remote Engine Start - Push Start

(A) Customer

Kona

Difficulty:

Part No.

Model Year

Copy OEM Logo Here (→)

2018~

J9F57 AC200

Note:

Denotes cautions to be taken to avoid

vehicle and component damage

Ratchet Extension

Authorized dealers use:

Denotes specific tools that are necessary

to complete a step

#2 Phillips

Screwdriver

Denotes cautions to be taken to avoid

physical injury or electronic component

damage

0.53

Basic Required Tools

Vehicle must be equipped with Smart Key (Push Button Start).

Ensure vehicle does NOT have Mechanical KEY.

Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.

(1) 855-225-7344

Denotes warnings that may lead to serious

physical injury or vehicle damage

N

O

T

E

Denotes important information to be

reviewed during the step

Denotes quality processes to be checked

prior to moving to the next step

Denotes personal protective equipment (PPEs) that

may be required for a step. Examples of safety

equipment icons noted below:

lbsAll dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed

options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load

Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying

capacity in kilograms or pounds, which is the total weight of all added options and accessories.

Load Label Part Number: NP070 - 09003

0.24 kg

The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct installation of the

Remote Engine Start kit. Disassemble vehicle components (including harness connectors) and install the kit components according to

each step, as indicated. Avoid disassembling or reassembling any components in advance to prevent unnecessary labor time and/or

installation errors.

(C) Master Technician or Specialist

Entered by

MPA

If this is a printed copy of the installation instructions, ensure you have the latest revision by

scanning the QR code or by entering the website address listed below before beginning

installation. Use the latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/j9f57_ac200.pdf

Revision Date

01/02/2019 of 10

Genuine Accessories

No. No.

1 6

2 7

3 8

4 9

5

Hardware Kit Contents

9

* Indicates extra components intentionally included in kit as spares.

Follow instructions for proper placement of each component.

Radio Presets - record customer preset frequencies if disconnecting battery power

Disconnecting Connectors Locking Connectors

When disconnecting connectors, grasp the connectors, not the wire. When locking connectors, listen for a click indicating they are securely locked.

AM3

SAT5

AM5

SAT3

A

9

FM1 FM5

Antenna

Wire Tie*

1 Antenna Harness

FM2

2 Transmitter Fob

1 Quick Reference Guide

Special Instructions

SAT1 SAT2

AM4

FM8FM6

Harness1

11 Warning Label

Description

Antenna Bracket

1

Hardware Total

FM7

Qty Description

Control Module

S/P: J9F57 AC030

Qty

S/P: J9F57 AC240

Kit Overview

S/P: 1WF57 AC340S/P: J9F57 AC210 S/P : 4ZF57 AC120S/P: D5F57 AC170

1

FM9

1 Owner's Guide

FM4

FM10

AM1

SAT4

AM2

FM3

9

Quick Reference Guide

Owner's Guide

CLICK

NO GOOD

8 7 6 5

1 2 3 4

Revision Date

01/02/2019 of 10

Genuine Accessories

Ratchet, Extension and 10mm Deep Well Socket

N

O

T

E

Remote Start Harness Connector Locations

WARNING! Shock Hazard. Do not touch vehicle's negative

battery terminal to vehicle's positive battery terminal. Serious

physical injury or electronic component damage may occur.

A. Remove the vehicle's Negative (-) Battery Terminal Cover, if applicable.

B. Disconnect and isolate the vehicle's Negative (-) Battery Cable.

2

A. Open the Driver's Door Window.

B. Move the Driver's Seat to the rearmost position.

C. Record all pre-set radio stations (if applicable).

D. Pull the Hood Lever to open the Hood.

N

O

T

E

1

Step 7 CAN Connector

(Behind Fuse Box)

Negative Battery Cable

Negative Battery Cover

Step 6 OBDII Connector

Revision Date

01/02/2019 of 10

Genuine Accessories

Caution! Do not damage the Lower Dash Panel, OBDII Connector or Electrical Connectors.

Trim Removal Tool

A. Disconnect the OBDII Connector.

B. Using a Trim Removal Tool, release the Retaining Tab.

C. By hand, dislodge the Lower Dash Panel.

NOTE: Pay special attention when disengaging the lower left hand side panel Tab.

D. Disconnect any Electrical Connectors from the Lower Dash Panel, if applicable.

E. Store the removed part in a safe location for reinstallation.

Caution: Do not damage the Dash Panel, Fuse Panel Cover or Dash End

Cap. Make sure no pressure clips remain in the dash board.

A. Remove the fuse panel cover.

B. Gently pull the weatherstrip back from the dash area.

C. Using a trim removal tool, remove the driver’s side dash end cap panel

by prying outward to disengage the three (3) pressure clips.

D. Store the removed parts in a safe location for reinstallation.

N

O

T

E

3

N

O

T

E

#2 Phillips ScrewdriverTrim Removal Tool

N

O

T

E

4

A. Using a Phillips Screwdriver, remove the two (2) phillips screws

from the side of the lower dash panel as shown.

B. Using a Phillips Screwdriver, remove the one (1) phillips screw

from the bottom of panel as shown.

C. Store the removed screws in a safe location for reinstallation.

Caution: Do not damage the Lower Dash Panel.

5

Pressure Clips

Fuse Panel Cover

Dash End Cap Panel

Phillips Screws

OBDII Connector

Pressure Clips

Retaining Tab

Lower Tab

Revision Date

01/02/2019 of 10

Genuine Accessories

Wire Cutters

Caution! Do not damage the Lower Dash Panel, OBDII Connector or Electrical Connectors.

N

O

T

E

A. Route the 16-Pin CAN Connector and Harness behind the Fuse Box.

B. Locate the factory 16-Pin Female CAN-Connector, found on the back side of the Fuse box, as shown above.

C. Disconnect the 16-Pin CAN Connector from the back side of the Fuse Box.

NOTE: The factory 16-Pin CAN Connector may be difficult to disconnect, make sure to fully press in the release tab before pulling out the connector.

D. Connect the corresponding Remote Start T-Harness Connector to the 16-Pin CAN Connector and Fuse Box (back side).

E. Using one (1) Wire Tie, secure the 16-Pin CAN Connector to Vehicle Harness as shown.

F. Trim excess Wire Tie material.

A. Connect the corresponding Remote Start OBD II Connector to the OBD II Connector disconnected from Lower Dash Panel.

B. Lock connectors in place tightly using two (2) Wire Ties behind connector slots to prevent separation between factory OBDII and Remote Engine Start OBDII

connector as shown.

Wire Cutters6

7

Ensure 16-Pin CAN Connector is fully seated in the Fuse Box.

N

O

T

E

Remote Start OBDII Connector

Factory OBDII Female Connector

16-Pin CAN Connector

Wire Tie

Fuse Box Back Side

Fuse Box Back Side

16-Pin CAN Connector

Wire Ties (2)

Slots

Wire Ties

Revision Date

01/02/2019 of 10

Genuine Accessories

A. Connect the 20-Pin Connector (black) to the Control Module.

B. Connect the 4-Pin Connector (black) to the Control Module.

C. Verify the following:

- Control Module is attached to Antenna Bracket.

- Both black 6-Pin connectors are attached to Antenna and Control Module.

Ensure that each Connector is fully seated in the Control Module and in the Antenna.

8

9 Wire Cutters

N

O

T

E

A. Position the Control Module Assembly (Control Module + Antenna + Antenna Harness + Antenna Bracket) close to the Grommet on Bulkhead, as shown.

B. Using two (2) Wire Ties, secure the Control Module Assembly to left side of the Factory Harness as shown.

C. Using two (2) Wire Ties, secure the Remote Start Harness to the Factory Harness as shown.

D. Trim excess Wire Tie material.

Ensure the Control Module Assembly is fully seated on the left of Factory Harness.

Ensure the Control Module Assembly does not interfere with the Steering Column Shaft.

N

O

T

E

Wire Tie Mounting Holes Feed wire tie through each hole on Control Module and

tie to vehicle harness.

Control Module Assembly

Grommet on Bulkhead

Wire Ties

Factory Harness

Black 6-Pin Antenna

Connectors

Black 4-Pin Connector

Black 20-Pin Connector

Antenna

Control Module

Antenna Bracket

MDPS

OBDII Connector

Fuse Box

Remote Start Harness Fuse

Wire Ties

Revision Date

01/02/2019 of 10

Genuine Accessories

Clean Cloth and 50/50 Mix of Isopropyl Alcohol (70%) and Water

12

N

O

T

E

GO TO → Function Check

A. Perform the Function Check at the end of the Instructions.

13 #2 Phillips Screwdriver

N

O

T

E

A. Reinstall all removed parts as follows:

- Install the Remote Start OBDII Connector to the Lower Dash Panel.

- Install the Lower Dash Panel ensuring the Lower Tab on the left hand

side bottom of panel is first tucked into the Kick Panel.

- Reinstall the Dash End Cap.

- Reinstall the Weatherstrip ensuring there are no kinks.

- Reinstall Fuse Panel Cover.

B. Place the Quick Reference Guide and the Owner’s Guide into the Glove

Box.

C. Attach the Remote Start Fobs to each of the Factory Key Fob Rings.

N

O

T

E

N

O

T

E

A. Reconnect the Negative (-) Battery Cable. Torque to:

5.0 ~ 6.0 N.m (0.5 ~ 0.6 kgf.m, 45 ~ 52 lb-in)

B. Reinstall the vehicle's Negative (-) Battery Terminal Cover, if applicable.

C. Make sure the Transportation Fuse is in the "ON" position.

D. Reinstall the weatherstrip at dash area to allow Driver's Door to

close properly.

E. Close the Hood, Tailgate and all Doors.

F. Test the LOCK / UNLOCK function using Smart Key Fob.

G. Enter the vehicle, holding a Smart Key, depress the Brake Pedal and

push the START button to start the engine.

H. Wait for 5 sec., and push the START button to stop the engine.

Ensure the surface is completely dry before installing the Warning Label.

Ensure the label is aligned straight with the edge of the Radiator Cover

and without air bubbles under the label.

NOTE: If vehicle is not responding, carefully re-check all wiring

connections. If the vehicle is still not responding, follow the

Troubleshooting at the end of the instructions.

10 11Ratchet, 10mm Deep Well Socket, Extension, and Torque

Wrench

A. Clean the left top surface of the Radiator Cover.

- Ensure the surface is completely dry.

B. Remove the Adhesive Liner from the Warning Label, then secure

the label to the Radiator Cover as shown.

Warning Label

Negative Battery Cable

Negative Battery Cover

Revision Date

01/02/2019 of 10

Genuine Accessories

NOTE: The Remote Engine Start system can recognize up to three (3)

Transmitter Fobs. The kit contains two (2) Transmitter Fobs. If a new Fob is

needed later, the Fob pairing process should be done with the original Fob,

or oldest available Fob.

N

O

T

E

Remote Start Transmitter Fob Pairing Procedure(not necessary for new installations - only needed if fob is replaced)

A. Open the Driver's Door and Tailgate.

B. Press LOCK button of Smart Key three (3) times within five (5) seconds.

C. Within five (5) seconds, press START button on the Remote Start

Transmitter Fob one (1) time.

D. If another Fob is to be paired, press the next Fob's START button within

five (5) seconds.

E. Verify that the new Fobs are functioning properly by performing a

LOCK/UNLOCK operation.

A

Remote Start Fob 1X Smart Key 3X

Revision Date

01/02/2019 of 10

Genuine Accessories

1. Press button 2 times.

2. Press button 2 more times.

Transmitter Fob UNLOCK icon will flash, vehicle signal lights will flash, and

Driver's door will UNLOCK.

Transmitter Fob UNLOCK icon will flash, vehicle signal lights will flash, and all

doors will UNLOCK.

Function Check

Items to be Checked Result

While the vehicle is running via remote start,

1. Press button one (1) time.

Transmitter Fob LOCK icon will flash, vehicle signal lights will flash, and all

doors will lock.

1. Press button one time.

(All doors, hood & trunk are closed).


doors will LOCK.

1. Press button one time.

2. Within 3 seconds, press and hold button for 2 seconds.


doors will LOCK.

Transmitter Fob KEY icon will flash, the engine will crank and start, the

vehicle signal lights will flash.

The hazard lights will flash while the engine is started remotely.


1. Press button two (2) times.

2. Press button two (2) additional times.

Transmitter Fob UNLOCK icon flash, vehicle signal light flashes twice

and Driver's door will unlock.

Transmitter Fob UNLOCK icon flash, vehicle signal light flashes twice

and All doors will unlock.

On the vehicle SMART KEY

1. Press button, one (1) time.

2. Within three (3) seconds, press or , one (1) time.

Vehicle signal lights will flash, and all doors will LOCK.

Engine will crank and start (there may be a short delay), the vehicle signal

lights will flash.

While the vehicle is running via remote start with the SMART KEY,

1. Press button one (1) time.

2. Press button one (1) additional time.

3. Press or button one (1) time.

Vehicle signal lights will flash, and Driver's door will UNLOCK.

Vehicle signal lights will flash, and all doors will UNLOCK.

The engine will stop.


1. Open the hood. The engine will stop.


1. Open driver's door and enter into vehicle with OE Smart KEY, close

the driver's door within 30sec.

The engine will continue running for drive off automatically.

(Hazard lights will stop flashing after drive off).


1. Open driver's door and press brake pedal with OE Smart KEY

within 30 sec.

The engine will continue running for drive off automatically.

(Hazard lights will stop flashing after drive off).


1. Open any door. The engine will stop after approximately thirty (30) seconds.


1. Open trunk.

The vehicle LOCKS, UNLOCKS, but does not START. Ensure the Valet Mode is OFF.

(Refer to Owner's Guide for details.)

Ensure that the buttons are properly activated.

Buttons may not recognize a command if the LED icon light is

still flashing.

The engine will stop after approximately fifty (50) seconds.

Troubleshooting

Symptom


1. Press and hold button for two (2) seconds. Transmitter Fob KEY icon will flash, and the engine will stop.

Items to be Checked

The vehicle does not LOCK by using the Remote Start Key Fob. Check the vehicle status

1. Engine is OFF.

2. Accessory function is OFF.

3. All doors are closed.

4. Hood and Tailgate are closed.

Engine turns off immediately when the brake pedal is pressed

after starting engine with remote.

Ensure Smart KEY FOB is inside the vehicle.

The remote does NOT LOCK / UNLOCK.

and does not START the vehicle. The Remote LED lights flash when buttons

are pressed.

The Transmitter Fob is not paired to the Control Module.

Follow the Remote Start Fob Pairing Procedure in the

Installation Instructions.

The LED icon lights on the Transmitter Fob does not light up. The Transmitter Fob batteries are dead.

Refer to the Owner's Manual for instructions to change the batteries.

The hazard lights will flash while the engine is started remotely. This is normal and cannot be changed.

Revision Date

01/02/2019 of 10

Genuine Accessories

Wiring Diagram

Revision Date

01/02/2019 of 10

Genuine Accessories - hyundaipartsdeal.com · Genuine Accessories Electronic Installation...

Documents

Transcript of Genuine Accessories - hyundaipartsdeal.com · Genuine Accessories Electronic Installation...