Garage Opener

8/3/2019 Garage Opener

1/32


2/32

!!Check your ceiling where the powerhead of your new unit will be mounted.

Plan how you will be mounting the power head.It is possible that ceiling joists may not be in theexact position needed with respect to the garagedoor operator. In any case, it may be necessaryto add an additional bracket and fasteners (notincluded with your new door operator kit).

You need a 110-120 Volt power supplyavailable. If you plan to plug the unit into astandard electrical outlet, is one available? Theoutlet should be no more than about 3 feet from thepower head once it is mounted. (The cord is 4 ft, inlength.) SEE WARNING BELOW.

Check the wail directly above the garagedoor. The door operator's header bracketmust be securely fastened to this wall. Insurethat the structure will provide a strong mountinglocation.

Check to see if the mounting locationfor the Safe-T-Beam System (STB) isclear from obstruction and has a woodsurface available for attaching the STBbrackets. The brackets may also be attached toconcrete if necessary but extra tools and specialfasteners (not supplied) will be required.s_"esws _;i_b th_"o_ 9h yo_ _"oc_:s Gene/3e_-:s e_"

Is your garage door made oflight-weight steel, aluminum, fiberglassor glass panels? Additional support bracingmust be added to these type doors, If this is thecase, please contact the door distributor ormanufacturer so that they can furnish you with a"bracing kit."

To avoid damage to your door and/oroperator, make sure you disable any doorlocks prior to installing your operator.

Insure that your door is properly balancedand moving freely. SEE WARNING BELOW.

(NOT SHOWN) If your garage does not havea separate entry door, you might want toconsider an emergency release kit (GER-2) forinstallation on your garage door. See page 30.


3/32

TYPICAL SECTIONAL DOOR iNSTALLATiON

/36" POWER CORDTO120V GROUNDEDOUTLETSUPPORTBRACKET

EXTENSION SPRINGOR

TORSION SPRING

ADDEDHEADER BRACKETMOUNTING BOARD

BRACES

SAFE-T=BEAM


4/32

OVERVIEW OFPOTENTIAL HAZARDSGaragedoorsarelarge,heavyobjectsthatmovewiththehelpofspringsunderhightensionandelectricmotors.Sincemovingobjects,springsundertension,andelectricmotorscan causeinjuries,yoursafetyandthesafetyofothersdependon youreadinghe informationnthismanual.Ifyouhavequestionsordonot understandheinformationpresented,callyournearestservicerepresentativeIn thissectionandthosethatfollow,thewordsDanger,Warning,andCautionareusedto emphasizemportantsafetyinformation.Theword:

_,DANGERmeansthatsevereinjuryordeathwill resultrom failuretofollowinstructions._,WARNINGmeansthatsevereinjuryor deathcanresultrom failuretofollowinstructions._.CAUTION meansthatpropertydamageorinjurycanresultfromfailuretofollowinstruction.Theword#,;OTli_susedtoindicatemportantstepstobefollowedorimportantconsiderations.

Safe-T-Beam (STB) Non-Contact Reversing System

IMPORTANTINSTALLATIONINSTRUCTIONS

Toreducethe riskofsevere injuryor death:1. READAND FOLLOWALL SAFETY,INSTALLATIONAND

OPERATIONINSTRUCTIONS.f you haveany questionsordo notunderstandan instruction,callyour servicerepresentative.

2. Do Not installoperatoron an improperlybalanceddoor.Animproperlybalanceddoorcouldcausesevereinjury.Repairsand adjustmentsto cables,springassembly,andotherhardwaremustbemadeby a trainedservicepersonusingpropertools andinstructions.

3. Removeall ropesand disableall locksconnectedtothe doorbefore installingoperator.4. Install dooroperator7feetor moreabovethe floor.Mountthe

emergencyreleaseknob6 feetabove thefloor.5. Do Notconnecttheoperatortothe sourceof poweruntilinstructedto doso.6. Locatethe controlbutton:

Withinsightof door. At a minimumheightof 5 feet,sosmallchildrencannotreachit.. Awayfromall movingpartsofthedoor.Installthe entrapmentWARNINGlabelnextto thewall buttonorconsole.Installthe emergencyreleasetag on,or nextto, theemergencyreleaseTheoperatormustreversewhenthedoorcontactsa 1-1/2inchhighobjecton theflooratthe centerof thedoorway.Thisis aboutthesize ofa 2" x 4" boardlaidflat.

Places an invisible beam across door opening that reverses the door during down travel to the fully openposition if anything passes through beam.Safe-T-Reverse Contact Reversing SystemAutomatically stops and reverses a closing door within 2 seconds of contact with an object.Safe-T-Stop Timed Reversed SystemAutomatically opens a closing door, if door does not close within 30 seconds.Force Guard ControlUsed to set the force required for opening and closing door. For maximum safety, set the minimum forcerequired to fully open and close door.Automatic Lighting SystemOne or two light bulbs (depending on model) up to 100 Watts max. each are used for safer entries and exits.The light turns on when door is activated and automatically turns off 4.5 minutes later.Manual Emergency ReleaseAllows the garage door to be opened or closed manually for emergencies or maintenance.


5/32

@ @@ remotesvary by model

_ Immmm

i!_L _ _ ,, . :i : i_:L:,_, _ "., !i _ :Lui

@FASTENERS - Shown full size. See Parts List for description.

Bol t, #10-24 x 1/2"--'m

Bolt, 5/16"-18 x 1/2"

Phil lips Hex Head Screw, No. 10 x 1-1/4"

1/4"-20 x 3/4"Self-Drilling Screw

Bolt, 3/8"-16 x 7/8"

Insulated Staple

Pan Head Screw #6 x 1-1/4"

Pan HeadPhillips ScrewNo. 8 x 5/8"aa _ _ D

Hex Head ScrewLag Screw, 1/4" x 2" Clevis Pin No. 8 x 3/4"

Speed Nut Cotter Pin

m

ZCold Head Pin

I


6/32


7/32


8/32


9/32


10/32


11/32

. Fasten rail to power head. Align mounting holes of sprocket saddle, railand power head frame. Insert the two (2) 5/16" x 1/2" hex headscrews[112], then two (2) No. 10-24 x 1/2" hexhead screws [69]. Tighten screws.

_:opower h


12/32

1. Establish center line of door and header (Fig. 2-1). Close door, Measure door width. Mark center. Use straight edge to draw vertical line "V."- down door about 6".

- on top of door.- up header about 20".

2. Establish Header Bracket position (Fig. 2-2). Watch top edge of door as you raise it. Stop door when top edge reaches highest pointof travel. Measure distance from top edge of door to floor. Add 2-1/2" to this measurement. Close door. Mark header at this height. If door spring is in the way, mark header 2-1/2"

above the spring. Draw horizontal line "H" across line "V" at thispoint (Fig 2-1).

NO_E:: _:_!_d_,rbf_'._cl2,,4/2> _bow_,hi_i_hpo#:_ _of d_:>o__w'e can be _:nsS3_edhi_i_hefdoo_ sphr Ls M _'hes,;':_y_Do No move _'hesph,n

Line "V"(Vertical Center Lineof Door) Line "H" Can BeSpring

Line "H"

DoorHeader Inside of Door

MarkHeaderOrAboveSpring

Header

Door

NOTE: Line "H" Can BeDrawn Above Spring

Spring Line "H"

Add 2-1/2"Minimum High Point,Of Door Travel

Door Track

Measure To Floor


13/32

3. install header bracket (Fig. 2-3) Place bracket so:- center hole is on line "V."- all holes are on line "H."

Mark hole positions "A" and "B." Drill 5/32" holes at marked positions. Fasten bracket to header using two (2) 1/4" x 2"

lag screws [79].4. Attach channel/rail assembly to header

bracket (Fig. 2-4). Fasten header end of the channel/rail to theHeader bracket with cold header pin [82].

Install speed nut [81]. Support power head above floor, use:

- rope.- ladder with cardboard packing.- wood.5. Level rail assembly and power head (Fig. 2-5).

Raise and support power head above door tracks. Open door. Level channel/rail assembly and

support temporarily. Center channel/rail assembly and power headon line "V" of door.

should be h_ve ff pess_Fe ff necessuy, po_


14/32

Top of Door

@Top of Door

8. Install door bracket (Fig. 2-6)., Contact door manufacturer.

9. Install door arms (Fig. 2-7). Attach straight door arm to carriage.- slip straight door arm into slot at bottom ofcarriage as shown.- secure with clevis pin [90] and cotter pin [89]. Attach short end of curved door arm to doorbracket as shown.- slip short end of curved door arm into slot indoor bracket.- secure with clevis pin and cotter pin.

Release carriage (See emergency release tag).- slide carriage towards closed door.- stop carriage 14" minimum from door.

10. Join door arm sections (Fig. 2-8).Use two (2) 3/8" x 7/8" hex bolts [91], and hexflange nuts [92].- use any two holes as far apart as possible.- slide carriage back and forth as needed toalign holes. Tighten hex nuts securely.

11. Adjust emergency release cord length. Mount the emergency release knob 6 feet fromthe floor. Retie overhand knot and trim excess cord.

DO NOT plug power cord into outlet.Go to Section 3-SAFE-T-BEAM SYSTEM INSTALLATION.

III

OR Top of Door

14" MIN. %

Straight door arm

Curved door arm

Straight door arm

Curved door arm [92]3/8-16 nut


15/32

1. Establish center (ine of door and header (Fig. 2-9). Close door. Measure door width. Mark center. Use straight edge to draw vertical line "V."- down door about 6."

- on top of door.- up header about 20".

2. Determine door rise (Fig. 2-10). Open door to highest point of travel. Measure distance from top of door to floor. Subtract the actual height of door. The remainderis the door rise in inches as shown in TABLE A.

TABLE ADoor risein inchesUp to 4"4" to 8"8"to 12"

Locate header bracket abovetop edge of CLOSED door

Upto 10"10" to 15"15" to 20". Locate header bracket (Fig. 2-9). Use TABLE A to determine header

bracket position. Draw horizontal line "H" across line "H" atthis point.

.. install header bracket (Fig. 2-11). Place header bracket so,- center hole is on line "V."- all holes are on line "H."

Mark hole positions ("A" and "B"). Drill 5/32" holes at marked positions. Fasten header bracket to header with two (2)

1/4"x 2" lag screws [79].

Line "V"(Vertical centerline of door) See

II

Inside of door

Top of door

Door rise

?Highest point Highest point Door r ise

of trave, of traveL._ _

Floor


16/32

5. Install door braces(See CAUTION below).

Attach channel/rail assembly to headerbracket (Fig. 2-13). Fasten header end of the channel/rail to the

header bracket with pin. Install speed nut onto pin (Fig, 2-14). Place cardboard packing under power head. Use

additional support if needed.

.

Establish power head mounting height (Fig. 2-15). Power head should be at door height above floor

or higher. Temporarily support power head in this position,Use

.

HeaderDoorbracket

Power head(Protected by cardboardor packing)

- rope.- ladder with cardboard packing.- wood.

Critical height is point where the rail/channel attaches to power head.

CORRECTf

m

.......ii!_i'ii_i_!ii!'i_i!7!i!!'i_i!!J!_i_i_!i!!'i:i!!i!!_i_i_!i!!'i:i!!i!!_i_!i!!'i:i!!i!!_i_i_!i!!'i:i!!i!i_!i!!'i:i!!i!!_i_i_!i!!'i:i!i_!i!!'i:i!!i!!_i_i_!i!!'i!_!!_:_!!_!!_i_!_!i_!!_i!_i!


17/32

9. Mount power head (See Section 2 ALTERNATEMOUNTING METHODS). Be sure rail assembly and power head are on

door center line (line "V'). Check the illustrations. Decide which mounting

method you will use. Materials for mounting arenot included. After power head is installed, remove

supporting material. Close door.10. Join door arms exactly as shown (Fig. 2-16).

Overlap arms by two (2) holes. Install two (2) 3/8" x 7/8" hex bolts, and hex

flange nuts.,, Tighten hex nuts securely.11. install assembled door arms (Fig. 2-17).

Attach straight end of assembled door arms todoor bracket.- slip straight door arm into slot in door bracket.- secure with clevis pin [90] and cotter pin [89].

, Release carriage (See emergency release tag). Slide carriage toward door. Attach short end of curved door arm to carriage.

- slip curved door arm into slot in carriage.- secure with clevis pin and cotter pin.

12. Adjust emergency release cord length. Mount the emergency release knob 6 feet fromthe floor. Retie overhand knot and trim excess cord.

ht door arm

[91],, Bolt, 3/8-16 x 7/8"/"[92]e' ,-"

3/8-16 nut O /

Curved door arm

Clevis pinCotter pin


18/32

Fs F_s _ ;ed. Mounting brackets. Mark both sides of garage door frame or wall 5"above floor (Fig. 3-1).

Hold bracket against door frame or wall.- Check if brackets extend out from wall farenough, so tongue of bracket is beyond door,tracks or any door hardware.- If not:a. STB bracket extensions are available atlocal dealer.

b. Blocks of wood, etc. may be substitutedfor extensions. Center bracket on your mark (Fig. 3-2). Fasten each with 2 screws [127].

[127] #10-16xi-1/4,,2, Mounting STB source and sensor. If garage has only one garage door.

- Determine which side of garage receivesmost direct sunlight (Fig. 3-4).- Red LED should always be on sunny sidewhenever possible (Fig. 3-4). For multiple doors.- Preventing crossed signals is critical.- Place source and sensor modules onadjacent doors facing in opposite directions(Fig. 3-4).

Slide source/sensor onto tongue of bracketuntil it clicks into place (Fig. 33).

, Wiring. Routewire using either method shown(Fig. 3-5). Securely fasten wires to wall as you go.- Use insulated staples (included).

[128] Insulatedstaple- Staples should be snug only.

ONE DOORGARAGE

TWO DOORGARAGE

THREEDOORGARAGE

Dashed Line = striped wireSolid Line = white wire

Source

A

1

IPowerHead

I i.

Source

PowerHead


19/32

Make wire attachments at STB's.- Splitting and stripping wire ends to be

connected as shown (Fig. 3-6).- Loosen terminal screws.- Insert wire under flat plate and tighten screw. It

does not matter which wire, white or striped,goes on which terminal (Fig. 3-7).

Make wire attachments at power head.- For ProMax. STB's are connected to terminals#2 and #3 on power head (Fig. 3-8).

- For Stealth. STB's are connected toterminals #3 and #4 on power head (Fig. 3-8).

4. Check the following. Insure that no part of door or its hardware is in

path between lenses of source and sensor. Insure that tops of lenses are between 5"-6"above the floor (Fig. 3-9). The brackets areflexible and can be adjusted slightly if needed.

DO NOT _LUG N _TT,!

To correct the problem - the brackets areflexible and can be adjusted slightly to bringthe system into alignment.When the STB's are in alignment the red LEDwill stop blinking and stay on.

SOURCE (RED LED) SENSOR (GREEN LED) INDICATED CONDITION REQUIRED ACTIONON _ ON NORMALOPERATION NONE REQUIRED

1.POWER HEADNOT POWERED 1.CHECK BREAKERS,FUSES, PLUGSO OFF O OFF 2.WIRING FROM POWERHEAD BAD 2.CHECK WIRING FOROBVIOUSSHORTS1.WIRING TO SOURCE MISSING OR BAD 1.CHECK WIRINGOFF ONlit 2. POWERHAS BEENINTERRUPTED 2. REMOVEPOWERAND REAPPLY1.BEAMNOT ALIGNED 2. BEAMOBSTRUCTED 1.CHECKALIGNMENT 2. CHECKFOROBSTRUCTION2 BLINKS, PAUSE(REPEAT) _ ON &SENSOR DEFECTIVE &CALL CUSTOMERSERVICE1.WIRETO SENSORMISSINGOR BAD 1.CHECKWIRING2 BLINKS, PAUSE(REPEAT) O OFF 2.SENSOR DEFECTIVE 2.CALL CUSTOMERSERVICE

Du_o_"_'"_,AUSE(REPEAT) _ ON 1.SENSORRECEIVINGINTERFERENCE 1.ATTEMPTTODETERMINESOURCEOFINTERFERENCE2.CALL CUSTOMERSERVICE1. SOURCENOT SENDINGPULSES 1.CALL CUSTOMERSERVICE4 BLINKS, PAUSE(REPEAT) _ ON 2.SOURCE DEFECTIVE 2.CALL CUSTOMERSERVICE

NOTE: IF O PERATING PROBLEM EXISTS, THE DOOR CAN BE CLOSED IF YOU: 1. DISCONNECT THE STB SYSTEM FROM THE OPERATOR AND 2. HOLD WALL CONTROL BUTTONDOWN UNTIL DOOR IS CLOSED. (REMOTE CONTROL & WIRELESS KEYPAD WILL NOT WORK WITHOUT STB)

CUSTOMER SERVICE: 1.800.354.3643 or www.geniecompany.com


20/32

.

.

3.

.

5.

Run wire from power head to wall control., Place the wall control:- In sight of door.- At least 5 feet from floor, so small children cannot reach it.- Away from moving parts of door anddoor hardware.

Use staples to fasten wire to ceiling and wall.Remove 1/2" insulation from each wire(Fig. 3-6)(pg. 19).Attach wires to terminals (Stealth Fig. 4-1a)(MAX Fig. 4-1b). Loosen, but Do Not remove screw from terminal.For Stealth.

- Connect striped wires to terminal "2" on powerhead and "B" on wall control.- Connect white wire to terminal "1" on powerhead and "W" on wall control.

For MAX.- Connect striped wires to terminal "1" on powerhead and "B" on wall control.- Connect white wire to terminal "2" on powerhead and "W" on wall control.

Mount wall control (Fig. 4-2). Use two pan head screws.Mount entrapment warning label. Remove protective backing and stick nearwall control. Use tacks or staples to permanently mount Label. Make sure everyone reads and follows WARNINGS.

Vacation Locking Switch- LOCKdisablescontrolsafterdooriscompletely closed- UNLOCKallowscontrolsto worknormallyIndependent Light Control- Controls door operator l ights from inside garage- Energy-Saver shut-off turns off l ight 5 minutes afterdoor activation

_>d_': O_TLYONE OF '_>UR_LL CON'_'_OLSM_YBE 7_EL GH TYPS B )S_ have a _jh_,d wa] 0 _9[;,_3Aou

Power head _ StripedterminalslLZ,:,_l i ,4J_l/I '-=_ I I I I_I wall............................ / I If_l ,_ I WhiteI I _ B_ button...............................


21/32

1. Check local building codes. Some building codes require direct wiring to abranch circuit. If direct wiring is NOT required,plug door operator into grounded outlet(Fig. 6-1).

2. Return to Section 3 for SAFE-T-BEAM Systemalignment and troubleshooting.

1. Disconnect the power cord from the branchcircuit mains.2. Remove bottom cover from power head.

Remove four (4) hex head screws from frontand rear covers. Slide bottom cover off.3. Remove existing power cord from power head. Disconnect three power cord wires. Remove and discard power cord. Remove 7/8" diameter knock-out plug. Install a suitable entrance bushing.

4. Install permanent wiring to power head.For Stealth--connect permanent wiring tointernal terminal block. Connect white supply line to silver terminal. Connect black supply line to brass terminal. Connect ground wire to green wire location

(GROUND).For ProMax--connect permanent wiring. Make connections with UL recognized wire nuts. Connect white supply line to white wire. Connect black supply line to black wire. Connect ground wire to green wire location

(GROUND). Wires inside operator are to be a minimum of6 inches.

5. Replace power head bottom cover. Replace and tighten four (4) hex head screws.

cover i:_ on po_:,r head befio_,!_ope_d


22/32

Before starting main limit switch settings, LOCKcarriage onto rail assembly (See emergencyrelease tag).1. Raise the door until the carriage engages withthe inner-slide/bullet.2. Set "OPEN" limit switch (Fig 6-1).

Locate limit set switch on back of power head. Push and hold limit set switch until door movesto the fully open position.- release the limit set switch.-"OPEN" limit switch is set.

NO_!:" !_dooy 's_'..#::_s_:mdfcdusc*s _o mov_ u_:?_d/:us_>"OP FORC.,/_ZpSee Sec_-o-n 7,_FORC;E3. Set "CLOSE" limit switch (Fig. 6-1). Push and hold limit set switch until door contacts

the ground and stops.- release limit set switch.-"CLOSE" limit is set.

NOTE; Ydoor s_ps and f_@,_,ses_'omove d%>_,'_adjust CLOSE FORCE* _ee Section 7,FORCEAJUS 7_ia_d t2_ens_ea_' se_ing t7_[t sw _'chNOX{!; Do Not pus_ the l_m_ set s h agai_ _


23/32

During the following steps, the motor protector mayopen. Wait about 20 minutes for protector to reset.C'LOSS_ pos _on befon_ s_'U_g OP_ FOF_CS

STEALTH

1. Adjust the "OPEN" Force (Fig. 7-1). Locate screw on back of power head marked"OPEN FORCE.", Gently turn screw counterclockwise until it stops.

NON_ L_o eHeT hsyequ _


24/32

During the following steps, the motor protector mayopen. Wait about 20 minutes for protector to reset.1. Adjusting the "OPEN" limit switch (Fig. 8-1).

Run door to open position by pushing wall control, Locate curved "OPEN" limit adjustment slot onback of power head. Look into slot for pinion screw. Insert a screwdriver and turn pinion screw.- clockwise to open more.

- counterclockwise to open less.2. Test door operator. Use wall control to run

door open and close.3. Repeat step as necessary to properly set"OPEN" limit switch.4. Adjust the "CLOSE" limit switch (Fig. 8-1).

Run door fully closed by pushing wall control. Locate curved "CLOSE" limit adjustment slot on

back of power head. Look into slot for pinion screw. Insert a screwdriver and turn pinion screw.- counterclockwise to close more.- clockwise to close less.

5. Test door operator. Use wall control to run dooropen and close

6. Repeat step as necessary to properly set"CLOSE" limit switch7. Perform CONTACT REVERSE

conSuLRemo_J;,con#_


25/32

Press and release a remote control button.- LED on power head stops blinking.

Press and release same remote button again.- LED goes out. Remote is now programmed.

2. Program multi-button remote control Repeat step 1 ("program one-button remote" for

each button).

3. Operate remote control Point remote control at door- Door moves

Press button again- Door stops Press button again- Door reverses

cose cyc4. Erasing aJJreceiver memory Press and hold learn code button on

power head- 10 seconds or until light goes out- Memory is erased

Program door operator again Press remote control button once within30 seconds- LED on power head stays lit

Press remote control button again- LED on power head goes out and remote

control is programmedsecon@ py_;_g,/_;.#_mmF_'_g,s_ss e4 Ffpy_s_gy_;_mm_;

Learn

indicator

Radio

Learn

o

1. Turn remote control upside down (Fig. 10-1)2. Battery replacement (your remote control is

battery powered). Gently push straight IN on tab as shown

(Fig. 10-1).- use ball point pen, coin or small screwdriver.- battery cover snaps open.

Install new battery in same position.- use A23, _,EIIEREAD[ 12 Volt battery.3. Attach visor clip to remote control (Fig. 10-2)

Slide visor clip into back of case until it snapsinto place.4. Remote control operation

Point remote control at the garage door andpress the button. Door will move.

Press remote control button again and doorwill stop.

Press remote control button again and the doorwill move the other way. The door automaticallystops at the end of the open or close cycle.

Visor clip"_-_ Battery__ cover

_ / Battery


26/32

1. install light bulb(s) into socket(s).Do Not use short neck bulb(s). Use bulb(s) rated for:

- rough service.- vibration.- appliances. 100 watt maximum.

2. Bend two (2) slotted tabs up. This will activatethe "living hinge" of the lens (Fig. 11-1).

3. Start two (2) No. 8 x 3/4" hex head screws intobottom holes of panel (Fig. 11-2). Slide slotted tabs up behind hex head screws. Tighten hex head screws.

4. Align lens holes and holes of panel. Insert and tighten a No. 8 x 5/8" pan head

screw into each round lens hole and tighten,

Bend tabs up (2)_,__

Slotted t_


27/32

DOOR SPRINGS and DOOR HARDWARE Do not operate garage door automatically ormanually if springs are broken. CONTACT APROFESSIONAL FOR SERVICE. Oil door rollers, bearings, and hinges monthly.Use silicone lubricant or light oil.

DOOR BALANCE Close door. Pull red emergency release knobdown and toward power head to release doorfrom rail assembly. Raise door manually approximately 3 feet. Doorshould stay in that position. If door moves, HAVEDOOR SERVICED BYA PROFESSIONAL. Close door. Pull red emergency release knob toreattach door to rail/channel assembly.

Toreducetherisk of

CONTACT REVERSE Close door on a 2 by 4 board laid flat on the floorin the center of the garage doorway. Close door by using wall button or remote control. If door fails to reverse on contact with the board,see Section 7-CONTACT REVERSE. If operator still fails, replace operator or HAVETHE DOOR SERVICED BYA PROFESSIONAL.Safe-T-Beam STB SYSTEM Use self-diagnostic Safe-T-Beam Systemtroubleshooting information to maintain safeoperation.(See Section 3-STB SYSTEM INSTALLATION.)

12

45

severeinjuryor death:READ AND FOLLOW ALL INSTRUCTIONS.Never let children operate or play with the DoorControls. Keep the Remote Control awayfrom children.Always keep the moving door in sight and awayfrom people and objects until the door is completelyclosed. NO ONE SHOULD CROSS THE PATH OFTHE MOVING DOOR.NEVER GO UNDER A STOPPED, PARTIALLYOPEN DOOR.Test Opener monthly. The door MUST reverse oncontact with a 1-1/2" high object (or a 2" x 4" boardlaid flat) at the center of the doorway on the floor.After adjusting either the Force or the Limit of travel,retest the Door Opener. Failure to adjust theOpener properly may cause severe injury or death.When possible use the Emergency Release onlywhen the door is closed. Use caution when usingthis Release with the door open. Weak or brokensprings are capable of increasing the rate of doorclosure and increasing the risk of severe injuryor death.

7 KEEP GARAGE DOORS PROPERLY BALANCED.See Owner's Manual. An improperly balanced doorincreases the risk of severe injury or death. Have aGenie Factory Authorized Dealer make repairs tocables, spring assemblies, and other hardware.8 SAVETHESE INSTRUCTIONS.

Transmitter Compliance StatementTransmitterscomplywithallUnitedStatesandCanadianegalrequirementsasof thedateof manufacture.Nowarrantyis madethattheycomplywithall legalrequirementsof anyotherjurisdiction.Iftransmittersare to beusedin anothercountry,theimportermustdeterminecompliancewithanylocallawsandregulationswhichmaydifferfromUnitedStatesandCanadianrequirementspriorto use.LostransmisorescumplencontodaslasreglamentacionesegalesdelosEstadosUnidosy delCanad,en lafechadefabricacin. Ningunagaranta se daque cumplancontodaslasreglamentacionesegalesdeningunaotrajurisdiccin. Si lostransmisoressevan a utilizarenotropas,el importadordebedeterminarsi cumplencon lasreglamentacionesleyeslocalesquepuedanserdiferentesa lasreglamentacionese los EstadosUnidosydel Canad,antesde usarlosmismos.

Les metteurssontconformes la r glementationam ricaineetcanadienne compterde leurdatedefabrication.Aucunegarantienest stipule indiquantqu ils sontconformes touteslesprescriptionsjuridiquesd autresautorits. Si les metteurssontutiliss dansd autrespays,il incombe I importateurden d terminerleurconformitauxloiset r gleslocalespouvantdiffrerde cellesdes tats-Uniset duCanadaavanttouteutilisationdesdits metteurs.Sendeger e entsprechenallen gesetzlichenBestimmungennden USAundKanadazumZeitpunktderHerstellung.Wir bernehmenkeineGewhrleistung r die EinhaltungallergesetzlichenBestimmungennanderenL ndern.SollenSendegere inanderenL nderneingesetztwerden,so mussder Importeurvordem Gebrauchsicherstellen,dassdieSendegere auchsolchenIokalenBestimmungenentsprechen,welchevondenBestimmungenderUSAundKanadasabweichen.

_o

_ _ o _g__ o,_7_


28/32

Use this guide to correct problems with your dooroperator. If these solutions do not work,call Customer Service.

PROBLEMOperator does not runfrom wall control.

Door starts down, thenstops before it's closed.

Door will only run closed.

Remote control hasless than 25 feetoperating range.

Operator runs, but doordoes not move.

Noisy operation.

Lights will not go out.

SOLUTIONSCheck lock switch on wall console (See section 4).Check the power source. Plug a lamp into outlet used for power head. If lamp works, power source is OK. If not, check fuseor circuit breaker. If power is OK:- Check connections at power head terminals.- Check connections at walt control.

- Motor protector may be open. Wait about 20 minutes for protector to reset.

Check CLOSE limit switch sett ing (See Section 8)Check for shorted wires

Check OPEN limit switch for short and proper wiring.Check force adjustment (See section 7).Check for broken door spring.

Relocate remote control inside car.Point remote control at door.Replace battery.Do Not attempt to retune remote controls.

Make sure carriage is engaged.Check force adjustment (See Section 7).

Be sure all fasteners are tight.Be sure door is in good repair, properly lubricated and balanced (See Monthly Maintenance section).

Check wiring.Disconnect & reconnect wires on wall control.Non-compatible walt control.


29/32

.....__ .... ....__o.... _c _ _o_&&w_1_o_ _

PURPLE _ REEN

WHITE I _ BLUEI t I_- ON MODEL,S THAT HAVE ONLY ONE LIGHT THE WHITE WIRE F ROM POSITION #UGHT THE BLUE WIRE F ROM POSlT_ON #11 AND THE LIGHT SOCKET ITSELF WILL BE OMITTED

I

MOTOR

ORANGE I GREEN

BLABN i PROTECTOR I MGTGB 11/BEO i_ .........0R_HOE L................... J

WIRE TO

WHITE _ _- _ _- HAVE OS SYSEEMPOWER

WHITE _ BLUE _ ON MODELS THAT H AVE O NL Y O NE L IG HT,/ THE WHITE WIRE FRO M PO SI TION # B THELIGHT BLUE WIRE F ROM P OSITION #12 AND THE

_E LIGHT SOCKET ITSELF WILL BE 0Mr TEDIWHITE


30/32

(GIT-I}l-Button RemoteControlwith Intellicode -Allowsremoteoperation of garagedoor.Controlador remote de lujo con Intellicode - Proporci6naroperaci6nremotede la puerta delgaraje.T_i_commandedeluxeavecIntellicode -Permettreoperation_loign"de porte degarage. P/N 33069 R $3650(GIT-2)-Button RemoteControlwith lntellicode - Allowsremoteoperationof 2garagedoors.Controladorremote de 2 funcionesconIntellicode- Proporci6naroperaci6nremotededos laspuertasdelgaraje.T_l_commande_ 2fonctions aveclntellicode - Permettreoperation_loign'deux portesdegarage. P/N 33069S $45.00(G[T-3) 3-Button RemoteControl with Intellicode - Allowsremoteoperationof 3garagedoors.Controladorremote de 3 funcionescon Intellicode- Proporci6naroperaci6nremotedetres laspuertasdel garaje.T_l_commande_ 3fonctions avecIntellicode - Permettreoperation_loign'troisportesdegarage. PIN 33069T $50.00(GPWC-2WLB} Lighted Wall Console- OperatesGarageDoor.Independentight control.Securityvacationlock.Consolede pared de 3funciones - Accionalapuerta delgaraje.Controldeluz independiente.Cerraduradeseguridadparavacaciones.Consolemurale _trois fonctions - Actionnela portedegarage.Commanded'[email protected] verrouillagedes_curit_. PIN 34292R $16.18(G_[-3) 3-ButtonMini RemoteControl with Intellicode"- Fitseasilyintopocketor purse.MJnicontrolador remote de 3 funcionescon Intellicode -Cavef_cilmenteenel boMIo ocartera.Mini t_l_commande _3 fonctions avecIntellicode -se glissedanslapochedevestonou lesachmain.PIN 34901R $40.00(GW_P} WirelessKeypadEntrySystem- OperatesIntellicodeGarageDoor Openerswithout RemoteControlor key.Sistemadeentrada pertedado num_rico inal_mbdco-Accionalosabridoresdepuertasde garajeIntellicode sin Jillcontrol remoteo llave. _Syst_med'ouvre-porte de garage_ clavier sansill- Actionnelosouvre-portedegarageavecIntellicodesans _t_l_commandeni cl_. P/N 35282R $52.00(GLU-3}14oz.Tubescrew riveLubricant3}- Ensuresroperquipmentearrotection.114once Lubdcantede tornil[o accionar (3}- AseguracomponentecorrectoprotecciOnperdeterioro.Laonza114Lubricant dela vis(3}- Garantircomponentexactparsyst_meddenseversuser. P/N 35164 R $500(6WB) UniversalWallRutton - Providesadditionalconvenientinsideoperation ofdoor.Rot6nde pared universal- Proporcionaoperaci6nconvenientede lapuertades@ elinterior.Routon m ural unJversel- Actionne I'ouvre-porte de I'int_rieurdu garage. P/N 34960 R $3.75(GPS-5)erfect Stop- Ensuresperfectparking.StopPerfecto- Aseguraelestacionamientoperfecto.Butoir PerfectStop- Permetde stationnerh la perfectiondens legarage. PIN 34964 R $4.00(6SXL-8) ExceleraterScrewDriveExtensionKit- AnExtensionhatincreaseshe travelof aScrewDriveOpenerto accommodateaneight foot door.Elextensi6ndeslizante de ExceleratorScrewDrive- Unaextensi6nparaaumentarlacarreradeun abridordeslizabledetornillo,paraacomodarunapuertade8 pies(2,43m).N_cessairede ral!ongedu ExceleratorScrewDrive- Rallongedeprolongeanta coursede I'ouvre-porteScrewDrivepour uneporte de2,4m (8pi)de hauteur. PIN 33523R $31.15(LCGX-8} ChainGlideTM ExtensionKit- An Extensionhat increaseshe travelof aChainGlideOpeneroaccommodatean eight foot door.Juego deextensi6nde cadenadeslizable - Unaextensi6nparaaumentarlaIongitud de labarandadeChainGlide,paraacomodarunapuertade8 pies(2,43m).N_cessaire de proiongement du coulisseau -RallongedeprolongeantlacoursedeI'ouvre-porteChainGlidepour uneporte de2,4m (8pi) dehauteur. PIN 00001085 $30.00(GSX-8) ScrewDrive ExtensionKit- Eighteeninch Extensiono increasetravel ofScrewDriveOperatorto accommodateeightfoot door.Juegodeextensi6n deslizante de ScrewDrive- Unaextensi6nde 18 pulgadasparaaumentarla carreradeun abridordeslizabledetomillo, paraacomodarunapuertade 8pies (2,43m.).N_cessairee raJlongedu ScrewDrive- Rallongede 30dm (I 8 po) prolongeantla , _s" ;,_ocoursedeI'ouvre-porte ScrewDrivepourune portede 2,4m (8pi) de hauteur.(GIRU-1T)UniversalConversionKit- Convertsany GarageDoor Openerto asecureradio signalsystem.Kit includesaRemoteControl,Receiverand Transformer. PIN 33523S $36.35(60 WATT} Enhanced/RoughServiceLight Bulb- Ensuresproperequiment comparability /%BombJllade60varies - Aseguracomponentecorrectode sistemar_dairagede 60 WATT- Garantircomponentexactparsyst_me P/N 26210A.S $2.73(GE_-2) Emergency Release Kit - Prov ides access to garage from outside in the event ofan electrical power failureJuego de p ica-porte de pesti llo - Permit ir en tr tada desde per fuera de garaje porque cor tede electricoN_cessa ires de D_denchement de secours - Len_cessaire de d_clenchementde secours est con_upour vous permettre d'acc_der _votre garage depuisI'ext_rieur en cas de panne de courant et Iorsqu'il PIN 34963R $20.00ST_ Adapter Brackets (2) - Used in conjunction with standard STBBrackets.They provide _aadditional clearance and mounting options _El adaptador pone entre par_ntesJs (2) - Usado en uni6n con par_ntesis uniformes demontar de STB,el los proporcionan elespacio l ibre adicional junto con mortar las opcionesCrochets d'adaptateur (2) -Util is_ conjointement avec STBstandard monter les crochets,ils f ournissent le d_gagement suppl_mentaire avec mentor d'options PIN 34439R.S $4.37

How many?sQuantos?Commentbeaucoup_

No C.OD. shipments. Please inc lude check or moneorder, made payable to The Genie Company. Do nosend cash. Allow 3-4 weeks for delivery.1-800-354-3643. P lease have part number and credcard ready. Mail Order Form to: Genie Company,Alliance, Ohio 44601. We accept Visa or Mastercardon phone orders only.Pleas e a dd loc al sa les tax i f yo u reside in on e of the states l istCal ifornia, Con ne ct icu t, F lor ida , Georgia, Illinois, IndianaMaryland, Massachuset ts, Michigan, New Jersey, New YOhio, Ten nes se e, Vi rginia, Wisc on sin

TOTAL ORDER $SHIPPING & HANDLING $ 5,00STATE SALES TAX $GRAND TOTAL $

No se aceptan ped ides de page contra entrega (CODSirvase inc lui r su cheque o gi ro postal , tacuentapagadera hecha a The Genie Company. No enviedinero en elective. Concedanos 3 a 4 semanas paraentrega. 1-800-354-3643. Sirvase tener l istos losnOmeros del modelo y de la tar je ta de cr_dito. Enviarhacer un pedido de mercancia a :Gen ie Company,All iance, Ohio 44601.Aceptamos pedidos telef6nicosVisa o Mastercard.Sirvase agregarel impuesto de ventaslocalsi ustedresideeunodelossiguientes estados:California, Connecticut, Florida, Georgia, Ill inois, IndianaMaryland, Massachusetts , Michigan, New Jersey, New YOh io , Ten nes se e, V irginia, Wis con sin

TOTAL DELPEDIDO $FLETE Y MANEJO $ 5,00IMPUESTO DE VENTAS ESTATAL $GRAN TOTAL $

u"_;t " @s*_ '_;;: .... ,4Pasd'exp@ditioncentre remboursement.Veuillez inclure unch@queou unmandat bancaire,le payablefait BThe GenieCompany. N'envoyez pas d'argent comptant. Accordez de4 semaines pour la Iivraison. 1-800-354-3643.Ayez sous lamain le num@ode lapiece et celui dela carte decredit. Me5 laposte learrngement _: Genie Company, Alliance, Ohio44601. Nous acceptonsles commandos part616phoneavecpaiement par carte de creditVisa ou Mastercard.Veuil iez ind iquer les taxes devente locales s i vous r_sidez dansdes _tats r_pertori_s ci-dessous.Cal ifornia, Conn ect icu t, F lo rida, Geo rgia, I ll ino is, Indiana ,Maryland, Massachusetts, Michigan, New Jer sey, New YoOhio, Ten ne ss ee , Vi rginia, Wis co ns inCOMMANDETOTALE $MANUTENTION ETEXPEDITION $ 5,00TAXE DE VENTE $TOTAL GLOBAL $

SHP OR{I}ERTO:EHVAR I,;t/_RO_'_CCOH:EXP_}ER_RC/{AH!I}SE POUR:NAME / NOMBRE / HeM

ADDRESS / DIRECCION / ADRESSE

CITY / CIUDAD /VILLE

STATE / ESTADO / ETAT

ZIP / CODIG O POSTAL / CODE P OS TAL

(Prices subject to change without notice)(Valoran el cambio con sujeci6n a sin nota)(Los prix assujettissent pour changer sans la notification)


31/32

NAMENAMENAMENAMENAMENAME

COMPANY,COMPANY,COMPANY,COMPANY,COMPANY,COMPANY,

NUMBERNUMBERNUMBERNUMBERNUMBERNUMBER


32/32

@

22790 Lake Park Blvd. Alliance, Ohio USA 44601

What is covered: Any defect in materialandworkmanshipfrom personal,normalhousehold usein accordancewith the Owner's ManualFor how long:300 Series- Motor 5 years and all other parts 3 years.500 Series- Motor Lifetime*and all other parts 5 years.1200Series- Motor Lifetime*and all other parts5 years. *Lifetimewarranty= warranted for aslong asyou ownyour home.Who gets the warranty: This warrantyis limitedto the consumer whooriginallypurchased the product.Geographic scope: This warrantyapplies only to Genie productspurchased in the UnitedStates, Canadaor Mexico.What we will do: Ifyour Genie product is defective,wewill repairit or, at our option, replace it at no chargeto you. Ifwe repairyourGenie product,wemay usenewor reconditionedreplacementparts. Ifwe choose to replaceyour Genie product,we may replace it with a new or reconditionedone of thesame or similardesign.Limitations: IMPLIEDWARRANTIES,INCLUDINGTHOSEOF FITNESSFORA PARTICULARPURPOSEANDMERCHANTABILITY(ANUNWRITTENWARRANTYTHATTHE PRODUCT IS FITFOR ORDINARYUSE),ARE LIMITEDTO ONEYEAR FROM THE DATEOF PURCHASE.GENIEWILLNOTPAYFOR:LOSSOF TIME; INCONVENIENCE;LOSS OF USEOF YOUR GENIEPRODUCTOR PROPERTYDAMAGECAUSED BYYOURGENIE PRODUCTOR ITSFAILURETO WORK;ANY SPECIAL, INCIDENTALOR CONSEQUENTIALDAMAGES;ORANY DAMAGESRESULTINGFROMMISUSEOR MODIFICATIONOF YOUR GENIEPRODUCT.

Some statesand provincesdo not allow limitationson howlong an implied warrantylastsor the exclusionof incidental or consequentialdamages, sothe above exclusions maynot apply to you.How to obtain warranty service: To obtainwarranty service for yourGenie product,you mustprovide proof of the dateand place of purchaseofthe product.1. Do-It-Yourself-Service.Callthe GenieConsumerConnection toll free at 1-800-354.3643a TrainedGenierepresentativeswill assist you in diagnosingtheproblemand will arrange to supplyyou with the required partsfor do-it-yourself repairs.Trained service representativesare available Monday-Friday,8:00 a.m. - 8:00 p.m.,EasternTime,and on Saturday,11:00a.m. to 5:00 p.m.,EasternTime(subject to holidays).2. Service FromAuthorizedDealers.Youalso may obtainwarranty service by calling the Genie ConsumerConnectionat 1.800.654.3643before reachingany agreementon service.If warrantyservice is providedby an authorizeddealer,Geniewill provideall required partsunderwarranty at no chargetoyou, butthe dealers are independentbusiness peopleand may rendera benchor service callcharge for their services. Geniewill not reimburseyou orotherwise be responsiblefor thosecharges.We suggestthat you retainyour originalpackingmaterial in the event you needto ship yourGenie product. Besure to includeyour name, address,telephone number,proof of date and placeof purchaseand a descriptionof the operatingproblem.After repairingor,at ouroption, replacing, your Genieproduct,we will ship it to yourhome at nocost to youfor parts and labor,but you will haveto paya minimumof $5.00 for shipping and handlingcharges.Yourchoice of any oneof the above-describedservice options is your exclusiveremedyunder this warranty.What this warranty does not cover: This warranty does not coverbatteries(which areconsidered replaceableparts), installation,commercial use,defectsresulting from accidents,damagewhile in transit to our service locationor damageresultingfrom alterations, misuseor abuse, lack of propermaintenance,unauthorizedrepair or modificationof theproduct,affixingof any attachment not providedwith the product,fire, flood, or acts of God, or

other failure tofollow the Owner's Manual.Thiswarranty is the only one we will give on your Genie product,and it sets forth all our responsibilitiesregarding yourGenie product.Thereareno other express warranties.State and province rights: Thiswarranty givesyou specific legal rights,and you mayalso have other rightswhichvary from state to state and provincetoprovince. Manufacturedunderoneor moreof thefollowing U.S.patents:3,898,582/4,041,259/4,048,630/4,064,487/4,103,238/5,222,403OtherPatentsappliedfor

CORRESPONDENCE WITH FACTORY MUST INCLUDE DATE / MFG. NO.(LOCATED UNDER LENS OF POWER HEAD)

Customer Service Or Visit Our Website

Garage Opener

Documents

Transcript of Garage Opener