G41T-M v80 Manual
-
Upload
erick-alcca-zela -
Category
Documents
-
view
240 -
download
1
Transcript of G41T-M v80 Manual
-
7/31/2019 G41T-M v80 Manual
1/68
-
7/31/2019 G41T-M v80 Manual
2/68
-
7/31/2019 G41T-M v80 Manual
3/68
-
7/31/2019 G41T-M v80 Manual
4/68
-
7/31/2019 G41T-M v80 Manual
5/68
-
7/31/2019 G41T-M v80 Manual
6/68
-
7/31/2019 G41T-M v80 Manual
7/68
-
7/31/2019 G41T-M v80 Manual
8/68
-
7/31/2019 G41T-M v80 Manual
9/68
-
7/31/2019 G41T-M v80 Manual
10/68
-
7/31/2019 G41T-M v80 Manual
11/68
-
7/31/2019 G41T-M v80 Manual
12/68
-
7/31/2019 G41T-M v80 Manual
13/68
-
7/31/2019 G41T-M v80 Manual
14/68
-
7/31/2019 G41T-M v80 Manual
15/68
-
7/31/2019 G41T-M v80 Manual
16/68
-
7/31/2019 G41T-M v80 Manual
17/68
-
7/31/2019 G41T-M v80 Manual
18/68
-
7/31/2019 G41T-M v80 Manual
19/68
-
7/31/2019 G41T-M v80 Manual
20/68
-
7/31/2019 G41T-M v80 Manual
21/68
-
7/31/2019 G41T-M v80 Manual
22/68
-
7/31/2019 G41T-M v80 Manual
23/68
-
7/31/2019 G41T-M v80 Manual
24/68
-
7/31/2019 G41T-M v80 Manual
25/68
-
7/31/2019 G41T-M v80 Manual
26/68
-
7/31/2019 G41T-M v80 Manual
27/68
-
7/31/2019 G41T-M v80 Manual
28/68
-
7/31/2019 G41T-M v80 Manual
29/68
-
7/31/2019 G41T-M v80 Manual
30/68
-
7/31/2019 G41T-M v80 Manual
31/68
-
7/31/2019 G41T-M v80 Manual
32/68
-
7/31/2019 G41T-M v80 Manual
33/68
-
7/31/2019 G41T-M v80 Manual
34/68
-
7/31/2019 G41T-M v80 Manual
35/68
-
7/31/2019 G41T-M v80 Manual
36/68
-
7/31/2019 G41T-M v80 Manual
37/68
-
7/31/2019 G41T-M v80 Manual
38/68
-
7/31/2019 G41T-M v80 Manual
39/68
-
7/31/2019 G41T-M v80 Manual
40/68
-
7/31/2019 G41T-M v80 Manual
41/68
-
7/31/2019 G41T-M v80 Manual
42/68
-
7/31/2019 G41T-M v80 Manual
43/68
-
7/31/2019 G41T-M v80 Manual
44/68
-
7/31/2019 G41T-M v80 Manual
45/68
-
7/31/2019 G41T-M v80 Manual
46/68
-
7/31/2019 G41T-M v80 Manual
47/68
-
7/31/2019 G41T-M v80 Manual
48/68
-
7/31/2019 G41T-M v80 Manual
49/68
-
7/31/2019 G41T-M v80 Manual
50/68
-
7/31/2019 G41T-M v80 Manual
51/68
-
7/31/2019 G41T-M v80 Manual
52/68
-
7/31/2019 G41T-M v80 Manual
53/68
-
7/31/2019 G41T-M v80 Manual
54/68
-
7/31/2019 G41T-M v80 Manual
55/68
-
7/31/2019 G41T-M v80 Manual
56/68
-
7/31/2019 G41T-M v80 Manual
57/68
-
7/31/2019 G41T-M v80 Manual
58/68
-
7/31/2019 G41T-M v80 Manual
59/68
-
7/31/2019 G41T-M v80 Manual
60/68
Setting Up eJIFFY
56
Feature IconsThe following illustration shows the main feature icons that eJIFFY provides on themenu.
ePix: Photo viewing.
eWeb: Firefox for web browsing/webmail and watching flash video.
Shows ePal on-line connection status.
Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer..
Click once to connect the storage disk to your computer. Click for the second time to remove your storage disk safely. (please refer to the FAQ for more usage information.)
Shows the network connection status.
ePal: On-line chat tool to use the most popular IMs in the world. (MSN,ICQ, AIM, etc.)
Language Control Panel
Switch Keyboard Languages
-
7/31/2019 G41T-M v80 Manual
61/68
Setting Up eJIFFY
57
to open the language control panel.
Keyboard Language Setup
Usage FAQLanguage Control Panel: Besides setting English as the default interface,eJIFFY offers multi-language displays and keyboard settings for language- switch. Open the language control panel to select a preferable language setting.
Step1. Click
Step 2: Click Keyboard Language icon to open the keyboard selection
list, which offers several regional keyboard settings besides default English keyboard.Step 3: Click the selected keyboard language (e.g. French) and press OK.
-
7/31/2019 G41T-M v80 Manual
62/68
Setting Up eJIFFY
58
Click the language bar here.
Move your mouse pointer on the text box and press Ctrl+Space. The language bar will then appear as fol- lows.
Select your desired language
Click to enable all possible language inputs you want to apply, and click
Apply:
-
7/31/2019 G41T-M v80 Manual
63/68
Setting Up eJIFFY
59
How to change display language?
Open the Language Control Panel and click to show the display language
list. Check your desired display language. Your selected display language will be
applied after rebooting.
Note: Details about eJIFFY please refer to eJIFFY in disk.
-
7/31/2019 G41T-M v80 Manual
64/68
Setting Up eJIFFY
60
Memo
-
7/31/2019 G41T-M v80 Manual
65/68
61
Trouble Shooting
Chapter 6Trouble Shooting
Start up problems during assembly
After assembling the PC for the first time you may experience some start upproblems. Before calling for technical support or returning for warranty, this chaptermay help to address some of the common questions using some basic troubleshootingtips.
a) System does not power up and the fans are not running.
1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB
and other peripherals including keyboard and mouse. Leave only the motherboard,CPU with CPU cooler and power supply connected. Turn on again to see if theCPU and power supply fans are running.
2. Make sure to remove any unused screws or other metal objects such as screwdriversfrom the inside PC case. This is to prevent damage from short circuit.
3. Check the CPU FAN connector is connected to the motherboard.
4. For Intel platforms check the pins on the CPU socket for damage or bent. A bentpin may cause failure to boot and sometimes permanent damage from short circuit.
5. Check the 12V power connector is connected to the motherboard.
6. Check that the 12V power & ATX connectors are fully inserted into themotherboard connectors. Make sure the latches of the cable and connector are
locked into place.
b) Power is on, fans are running but there is no display
1. Make sure the monitor is turned on and the monitor cable is properly connectedto the PC.2. Check the VGA adapter card (if applicable) is inserted properly.3. Listen for beep sounds. If you are using internal PC speaker make sure it isconnected.
a. continuous 3 short beeps : memory not detectedb. 1 long beep and 8 short beeps : VGA not detected
-
7/31/2019 G41T-M v80 Manual
66/68
62
Trouble Shooting
c) The PC suddenly shuts down while booting up.
1. The CPU may experience overheating so it will shutdown to protect itself.Ensure the CPU fan is working properly.2. From the BIOS setting, try to disable the Smartfan function to let the fan run atdefault speed. Doing a Load Optimised Default will also disable the Smartfan.
Maintenance and care tips
Your computer, like any electrical appliance, requires proper care and maintenance.Here are some basic PC care tips to help prolong the life of the motherboard andkeep it running as best as it can.
Start up problems after prolong useAfter a prolong period of use your PC may experience start up problems again.This may be caused by breakdown of devices connected to the motherboard such asHDD, CPU fan, etc. The following tips may help to revive the PC or identify thecause of failure.
1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When
completed, follow up with a Load Optimised Default in the BIOS setup.
2. Check the CPU cooler fan for dust. Long term accumulation of dust willreduce its effectiveness to cool the processor. Clean the cooler or replace a
new one if necessary.
3. Check that the 12V power & ATX connectors are fully inserted into themotherboard connectors. Make sure the latches of the cable and connectorare locked into place.
4. Remove the hard drive, optical drive or DDR memory to determine which of these component may be at fault.
1. Keep your computer in a well ventilated area. Leave some space betweenthe PC and the wall for sufficient airflow.
2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlightand areas of high moisture content.
3. Routinely clean the CPU cooler fan to remove dust and hair.4. In places of hot and humid weather you should turn on your computer once
every other week to circulate the air and prevent damage from humidity.5. Add more memory to your computer if possible. This not only speeds up the
system but also reduces the loading of your hard drive to prolong its lifespan.6. If possible, ensure the power cord has an earth ground pin directly from the
wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.
-
7/31/2019 G41T-M v80 Manual
67/68
Power Bu
onispressed
but PCfails
tostart.
Yes
Check ifPowerSupply
Unit (PSU) is working
No
No
Any Beepsound
No
CLR CMOS and check
ifCPU 12Vpower
isconnected
artthe PC
st
Re
Problem withPSU or board?
Ifboardproblem ->contact RMA
ACpower cordis plu
ed
gg
andPSUswitchisturnedon?
Yes
oblem
r
Boardp
->contactRMA
No
-If3shortbeeps:
DIMM memory not properly
insertedor memory failure
- If 1 long beepand 8 short beeps:
VGA not detected
Yes
Yes
Halt at POSTscreen
Yes
R CMO
LC
Sand restart.
Iffail, contact RMA
Yes
No
Peripheraldevice issue
-
HDDproblem.
-
CMOSsetup error,
d
nee to CLRCMOS.
System failtostartorunstable
a
er modify BIOS se
ng.
M
CLRC
OS and restart
Turnon PSUswitch
orconnecttowallsocket
start.
e
andrN
o
Checkifmonitor h
sa
display
Checkifmonitor
hasdisplay
B a s i c
T r o u
b l e s h o o
t i n g
F l o w c h a r t
-
7/31/2019 G41T-M v80 Manual
68/68
64
Memo