G-U BKS Locks for narrow stile doors - All products
description
Transcript of G-U BKS Locks for narrow stile doors - All products
Locks for narrow stile systems
Locks
Products of the G.U-Group for doors
Security locks
Content
Contract mortise locks
4
Page 8 Page 14Page 12Page 10
1926 121812121974
1425 143014271426
1200 12151205PZ1200RF
1812 1828
Page 16 Page 22Page 20Page 18
Page 26 Page 32Page 30Page 28
Page 34 Page 36
Special locks
0007 1205SRHF1205SRH1205H
Page 40 Page 46Page 44Page 42
Striking plates
Content
5
Page 50 Page 51Page 50Page 50
B9000 S401B9000B9000
Page 55 Page 57Page 56Page 56
S491
Page 57
S491
S491S491S491
Page 53 Page 55Page 54Page 54
S491 S491S491S491
Page 51 Page 53Page 52Page 52
S491 S491S412S412
Product features
6
Automatic locking locks – Series 19Series 19 is the result of our consistent development of innovativeproducts. Based on series 21 now also for narrow stile doors withsmall backsets.
Performance characteristics such as automatic locking, burglary prevention,fire rated and emergency exit doors according to new European standardsprovide numerous possibilities in the development and equipment of narrowstile systems.
LatchboltAssures the best security as additional locking.The integrated lever allows the latchbolt toadvance automatically from 12 to 20 mm.
ForendAs fixing element of the lockwith the door.The various design scopes ofsurfaces and shapes must bespecified in the order.
Automatic deadboltProjects automatically by 20 mmand provides an improved lockingand security in combination withthe latchbolt.May also be manually locked incase of lock 1974. The handle isswitched to free running action.
Locking methodMay be supplied for profilecylinders or Swiss roundcylinders.
Clamping followerReceives the spindle of thedoor furniture without any playand provides a reliable lockoperation.
Sound dampingProvides quiet actionwhen closing the door.Very important whenusing narrow stile profiles.
Lock caseStable design with a small behindbackset of 15 mm, fits into all recessesof the familiar BKS series 18.
BacksetFrom 35 mm and must be specifiedin orders.
Product features
7
Safety locks for narrow stile systemsAutomatic locking locks – series 19
Application: Narrow stile entrance doorsTechnical features:– profile cylinder lock with latch lever function, 92 mm distance– automatic locking of latchbolt and automatic deadbolt by integrated lever, therefore no auxiliary latch is necessary– lock 1926 no longer requires manual locking of the door– anti-panic latch lever function E is standard in case of lock 1926– optional with manually locking deadbolt, the handle is switched to free running action– suitable in combination with BKS door furniture according to DIN EN 1125 + DIN EN 179– fire rated suitable according to DIN 18250 + DIN EN 1634– can be supplied in backsets 35, 40, and 45 mm– galvanized lock case– 15 mm behind backset, fits into all recesses of the familiar series 18– various forend versions in regards to form and optics
Safety lock 1212Application: Narrow style entrance doorsTechnical features:– profile cylinder lock with latch lever function, 92 mm distance– can be supplied in backsets 25, 30, 35, 40 and 45 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– zinc die-cast latch, steel safety bolt– reversible latch, usable DIN LH + DIN RH– latch and deadbolt optionally with special anti-friction coating– 1-turn 20 mm latch throw– also available in SKG approved version– various forend versions in regards to form and optics
Safety deadbolt lock 1218Application: Additional locking on narrow stile entrance doorsTechnical features:– profile cylinder lock– can be supplied in backsets 25, 30, 35, 40 and 45 mm– galvanized lock case– steel safety latch– reversible latch, usable DIN LH + DIN RH– 1-turn 20 mm latch throw– also available in SKG approved version– various forend versions in regards to form and optics
Safety locks with pivot bolt – series 14Application: Narrow stile entrance doorsTechnical features:– profile cylinder lock, 92 mm distance– can be supplied in backsets 25, 30, 35, and 40 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– optional with reversible latch, roller latch or as deadbolt lock– safety pivot bolt with hardened steel bolts– optionally with additional safety deadbolt as lock 1430– various forend versions in regards to form and optics
Door open Door closed– Latch and deadbolt project
automatically
Lock 1926 – automatic locking
8
Door closed– Latch and deadbolt are with-
drawn when operating thelever
Range / Order numbers
Narrow stile lock with flat forend
Additional possibilities (upon request)
Specification text
Automatic locking BKS mortise lock 1926 for narrow stile doors; suitable according DIN 18250 for fire rated doors according to DIN 4102 and in combina-tion with BKS door furniture for entrance fire rated doors according to DIN EN 1634; stainless steel forend, square, flat forend 24 x 3 mm (“U” shapedforend 24 x 6 mm, with decorative plastic end caps for an optional attachment with pop rivet nuts or integrated dowel technique); latch lever function Ewith latch lever; suitable in combination with BKS door furniture according to DIN EN 179 (emergency exit doors) and DIN EN 1125 (anti-panic doors);galvanized lock case; with assembly friendly guide of the cylinder fixing screw; special 9 mm follower, reinforced follower bearing; automatic latchbolt withintegrated lever, in closed position with a 20 mm latch projection and advancing automatic deadbolt; automatic latch and deadbolt in a secured version asdouble locking; behind backset of 15 mm; center distance of 92 mm; _____ mm backset
Lock 1926 – automatic locking
ForendSurface
Backsetin mm
FrontForm
Flat forend 24 x 3 mmDIN LH DIN RH
Stainless steel
squaresquaresquaresquaresquaresquaresquare
B 1926 0003B 1926 0005B 1926 0007B 1926 0009B 1926 0011B 1926 0013B 1926 0015
B 1926 0004B 1926 0006B 1926 0008B 1926 0010B 1926 0012B 1926 0014B 1926 0016
35404550556065
Narrow stile mortise lock with “U” shaped forend
ForendSurface
Backsetin mm
ForendForm
“U” shaped forend 24 x 6 mmDIN LH DIN RH
Stainless steelsquaresquaresquare
B 1926 0503B 1926 0505B 1926 0507
B 1926 0504B 1926 0506B 1926 0508
343944
Backsetin mm
ForendAppearance Width Special versions
Possible striking platesFollower
Swiss round cylinder holeB 9000 0402B 9000 0435B 9000 0436
9
Lock 1974 with manual lockable latch
10
Door open Door closed– Locking cylinder locked– Door handle in free running
position
Door closed– Latch projects automatically– Locking of deadbolt by use
of key
Range / Order numbers
Specification text
Automatic locking BKS mortise lock 1974 with manual locking bolt for narrow stile doors; stainless steel forend, square, flat forend of 24 x 3 x 270 mm(“U” shaped forend 24 x 6, with decorative plastic end caps for an optional attachment with pop rivet nuts or integrated dowel technique); with latch lever;galvanized lock case; with assembly friendly guide of the cylinder fixing screw; special 9 mm (8 mm) follower, reinforced follower bearing; automaticlatchbolt with integrated lever, in locking position with a 20 mm latch projection and manually locking advancing deadbolt; lever in free running positionwhen the deadbolt is locked; automatic latch and deadbolt in a secured version as a double locking; behind backset dimension of 15 mm; center distanceof 92 mm; _____mm backset
Lock 1974 with manual lockable latch
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
8 mmSwiss round cylinder perforation
B 9000 0402B 9000 0435B 9000 0436
11
Narrow stile lock with flat forend
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 3 mmDIN LH DIN RH
Stainless steel
squaresquaresquare
B 1974 0003B 1974 0005B 1974 0007
B 1974 0004B 1974 0006B 1974 0008
354045
Narrow stile mortise lock with “U” spaped forend
ForendSurface
Backsetin mm
ForendForm
“U” shaped forend 24 x 6 mmDIN LH DIN RH
Stainless steelsquaresquaresquare
B 1974 0503B 1974 0505B 1974 0507
B 1974 0504B 1974 0506B 1974 0508
343944
Safety narrow stile lock 1212
12
Range / Order numbers
Other options (upon request)
Specification text
BKS narrow stile safety lock 1212; nickel-silver painted forend (or stainless steel), square, flat forend 24 x 3 mm (“U” shaped forend 24 x 6 mm) /stainless steel only, with decorative plastic end caps for an optional attachment with pop rivet nuts or integrated dowel technique); with latch lever;galvanized lock case; with assembly friendly guide of the cylinder fixing screw; special 9 mm (8 mm) follower, reinforced follower bearing; screw holesfor narrow stile door furniture with connecting screws of up to M 6 around the follower and cylinder fixing holes; zinc die-cast reversible latch, usableDIN LH + DIN RH; one turn galvanized steel safety latch with 20 mm latch projection; behind backset of 15.5 mm; center distance 92 mm; ____ mmbackset
Safety narrow stile lock 1212
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
9 mmLatch + deadbolt withanti-friction coating
S4910064 (nisi)S4910040 (niro)S4910071 (SKG)
S4910078 (“U” shaped)
13
Narrow stile lock
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 3 x 270 mm “U” shaped forend 24 x 6 x 268 mm
----------
usable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquaresquaresquare
12120064121200541212006312120065121200661212005712120058121200591212006012120056
usable DIN LH + DIN RH
24 mm backset29 mm backset34 mm backset39 mm backset44 mm backset
1212201712122018121220191212202012122021
25303540452530354045
Narrow stile safety lock according to SKG
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 3 x 270 mmusable DIN LH + DIN RH
Stainless steel
squaresquaresquaresquare
12120067121200691212007112120073
30354045
Safety deadbolt lock 1218
14
Range / Order numbers
Other options (upon request)
Specification text
BKS safety deadbolt lock 1218 for profile cylinders; nickel-silver painted forend (or stainless steel), square; 224 x 3 mm flat forend (“U” shaped forend 24 x 6 mm / stainless steel only, with decorative plastic end caps for an optional attachment of pop rivet nuts or integrated dowel technique); galvanizedlock case; galvanized steel safety deadbolt with a one turn 20 mm deadbolt projection; usable DIN LH + DIN RH; behind backset 15.5 mm; _____ mmbackset
Safety deadbolt lock 1218
Backsetin mm
ForendFinish Width
Special versions Possible striking platesFollower
S4120026 (nickel-silver)S4120008 (stainless steel)
S4120027 (SKG)S4120028 (“U” shaped)
15
Safety deadbolt lock
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 3 mm “U” shaped forend 24 x 6 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquaresquaresquare
12180027121800241218002512180029121800301218002812180022121800261218003112180032
usable DIN LH + DIN RH----------
1218003712180038121800391218004012180041
25303540452530354045
Narrow stile deadbolt lock according to SKG
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 4 mmusable DIN LH + RH
Stainless steel
squaresquaresquaresquare
12180033121800341218003512180036
31364146
24 mm backset29 mm backset34 mm backset39 mm backset44 mm backset
Safety pivot hook bolt lock 1425
16
Range / Order numbers
Other options (upon request)
Specification text
BKS pivot hook bolt lock 1425; nickel-silver painted forend (or stainless steel), square; galvanized lock case; with assembly friendly guide of the cylinderfixing screw; screw holes for narrow stile door furniture with connecting screws up to M 6 around follower and cylinder hole; 8 mm steel follower; zinc die-cast reversible latch, usable DIN LH + DIN RH; safety hook bolt with hardened steel bolt; 15.5 mm behind backset; 92 mm center distance; _____ mmbackset
Safety pivot hook bolt lock 1425
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
9 mm S4910046 (ns)S4910047 (ss)
17
Pivot bolt lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 x 3 x 255 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquare
1425001714250018142500191425002014250021142500221425002314250024
2530354025303540
Safety pivot hook bolt lock 1426 with roller latch
18
Range / Order numbers
Additional possibilities (upon request)
Specification text
BKS safety pivot hook bolt lock 1426 with roller latch; nickel-silver painted forend (or stainless steel), square; galvanized lock case; with assembly friendlyguide of the cylinder fixing screw; screw holes for narrow stile door furniture with connecting screws up to M 6 around follower and cylinder hole;adjustable brass roller latch, adjusting range of 3 – 10 mm; safety pivot hook bolt with hardened steel bolt; usable DIN LH + DIN RH; 15.5 mm behindbackset; 92 mm center distance; _____ mm backset
Safety pivot hook bolt lock 1426 with roller latch
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
S4910075 (ns)S4910059 (ss)
19
Pivot bolt lock with roller latch
ForendSurface
Backsetin mm
ForendForm
Forend 24 x 3 x 255 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquare
1426000914260010142600031426000414260011142600121426001314260008
2530354025303540
Safety pivot hook bolt lock 1427
20
Range / Order numbers
Other options (upon request)
Specification text
BKS safety pivot hook bolt lock 1427; nickel-silver painted forend (or stainless steel), square; galvanized lock case; with assembly friendly guide of thecylinder fixing screw; screw holes for narrow stile door furniture with connecting screws up to M 6 around follower and cylinder hole; safety pivot hook boltwith hardened steel bolt; 15.5 mm behind backset; 92 mm center distance; _____ mm backset
Safety pivot hook bolt lock 1427
Backsetin mm
ForendFinish Width
Special versions Possible striking platesFollower
S4910037 (ns)S4910038 (ss)
Guiding bolt
21
Pivot bolt lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 x 3 x 255 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquare
1427000514270006142700071427000814270013142700141427001514270016
2530354025303540
Safety pivot hook bolt lock 1430
22
Range / Order numbers
Other options (upon request)
Specification text
BKS safety pivot hook bolt lock 1430 with additional deadbolt; stainless steel forend, square; galvanized lock case; with assembly friendly guide of thecylinder fixing screw; screw holes for narrow stile door furniture with connecting screws up to M 6 around follower and cylinder hole; 9 mm steel follower;zinc die-cast latch; safety pivot bolt with hardened steel bolt; additional steel deadbolt; 15.5 mm behind backset; 92 mm center distance; _____ mmbackset
Safety pivot hook bolt lock 1430
Backsetin mm
ForendFinish Width
Special versions Possible striking platesFollower
8 mm S4910076
23
Pivot hook bolt lock
ForendSurface
Backsetin mm
FrontForm
Forend 24 x 3 x 255 mmDIN LH DIN RH
Stainless steel square 14300001 1430000240
Product features
Contract mortise locks for narrow stile systems
LatchProvides a durable locking of the door.Reversible in most locks, these aretherefore suitable for right and lefthanded doors.
ForendAs fixing element of the lock with the door.The various design scopes of surfaces andshapes must be specified in the order.
DeadboltSecures a closed door againstunauthorized entry.
Locking methodFor profile cylinders with latchlever function.
FollowerReceives the spindle of thedoor furniture and operatesthe lock.
Lock caseAs stable galvanized design, it protectsthe function of the lock with a smallbehind backset.
BacksetMust be specified in orders.
24
Product features
Contract mortise locks for narrow stile systems
Application: Narrow stile internal doors
Technical features:– profile cylinder lock with latch lever function, 92 mm distance– can be supplied in backsets 25, 30, 35, 40 and 45 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– reversible zinc die-cast latch, usable DIN LH + DIN RH or brass roller latch– one turn steel deadbolt, with 20 mm deadbolt projection– 16 mm forend width suitable for section with Euro groove
Application: Narrow stile internal doors
Technical features:– profile cylinder lock with latch lever function, 72 mm distance– can be supplied in backsets 25, 30, 35 and 40 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– zinc die-cast latch, steel safety deadbolt– reversible latch, usable DIN LH + DIN RH– one turn 20 mm latch throw– various forend versions in regards to form and optics
Application: Narrow stile internal doors with swing door function
Technical features:– profile cylinder lock– roller latch adjustable from the forend, adjusting range of 4 – 12 mm– can be supplied in backset 25, 30, 35, 40 and 45 mm– galvanized lock case– one turn steel deadbolt, with 20 mm deadbolt projection– various forend versions in regards to form and optics
25
Roller latch lock 1215
Application: Narrow stile internal doors
Technical features:– profile cylinder lock with latch lever function, 92 mm distance as 1828– deadbolt lock, 92 mm distance as 1812– can be supplied in backsets 25, 30, 35, 40 and 45 mm– galvanized lock case– latch of 1828 made of steel, deadbolt of 1828 + 1812 made of steel– reversible latch of 1828, usable DIN LH + DIN RH– one turn 14 mm latch throw– various forend versions in regards to form and optics
Narrow stile lock – series 18
Lock 1205
Lock 1200 + roller latch lock 1200RF
Narrow stile lock 1200
26
Range / Order numbers
Specification text
BKS narrow stile lock 1200; nickel-silver painted forend (or stainless steel), square; flat forend 16 x 3 mm; with latch lever; galvanized lock case; withassembly friendly guide of the cylinder fixing screw; special 8 mm follower; screw holes for narrow stile door furniture with connecting screws up to M 6around follower hole; zinc die-cast reversible latch, usable DIN LH + DIN RH; one turn galvanized steel deadbolt with 20 mm deadbolt projection; 15.5 mmbehind backset; 92 mm center distance; _____ mm backset
Narrow stile lock 1200
27
Other options (upon request)
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
Latch fixing deviceAccessories fromthe G. U Secury
Program
Narrow stile lock 1200
ForendSurface
Backsetin mm
ForendForm
Forend 16 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquaresquaresquare
12000008120000061200001012000011120000121200002812000026120000271200002912000030
25303540452530354045
Roller latch lock 1200RF
28
Range / Order numbers
Specification text
BKS roller latch lock 1200 for narrow stile doors; nickel-silver painted forend (or stainless steel), square; flat forend 16 x 3 mm; galvanized lock case; with assembly friendly guide of the cylinder fixing screw; screw holes for narrow stile door furniture with connecting screws up to M 6 around followerhole; brass roller latch, usable DIN LH + DIN RH; one turn galvanized steel deadbolt with 20 mm deadbolt projection; 15.5 mm behind backset; 92 mmcenter distance; _____ mm backset
Roller latch lock 1200RF
Stainless steel
29
Other options (upon request)
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
Accessories fromthe G. U Secury
Program
Roller latch lock 1200
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 4 mmusable DIN LH + DIN RH
Steelnickel-silver
squaresquaresquaresquare
12000022120000231200002412000025
30354045
Narrow stile lock 1205
30
Range / Order numbers
Specification text
BKS narrow stile lock 1205; nickel-silver painted forend (or stainless steel), square; with latch lever; galvanized lock case; with assembly friendly guide ofthe cylinder fixing screw; special 8 mm follower; zinc die-cast reversible latch, usable DIN LH + DIN RH; one turn galvanized steel deadbolt with 13 mmdeadbolt projection; 16.5 mm behind backset; 72 mm center distance; _____ mm backset
Narrow stile lock 1205
31
Other options (upon request)Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
S4910023 (ns)S4910025 (ss)
Narrow stile lock 1205
ForendSurface
Backsetin mm
ForendForm
Forend 24 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquare
1205000512050001120500061205000712050120120500621205006012050056
2530354025303540
Roller latch lock 1215
32
Range / Order numbers
Specification text
BKS roller latch lock 1215 for narrow stile doors; nickel-silver painted forend (or stainless steel), square, flat forend 24 x 255 mm (“U” shaped forend 24 x 6 mm) / stainless steel only, with decorative plastic end caps for an optional attachment with pop rivet nuts or integrated dowel technique); galva-nized lock case; with assembly friendly guide of the cylinder fixing screw; screw holes for narrow stile door furniture with connecting screws of up to M 6around the follower and cylinder perforation; adjustable brass roller latch, adjustment range of 3 – 10 mm, usable DIN LH + DIN RH; single turn galvanizedsteel deadbolt with 20 mm deadbolt projection; behind backset of 15.5 mm; center distance of 92 mm; ____ mm backset
Roller latch lock 1215
33
Other options (upon request)
Backsetin mm
ForendFinish Width Sspecial versions
Possible striking platesFollower
S4910065 (ns)S4910042 (ss)
S4910077 (“U” shaped forend)
Roller latch lock
ForendSurface
Backsetin mm
ForendForm
Flat forend 24 x 3 x 255 mm “U” shaped forend 24 x 6 x 270 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquaresquaresquaresquaresquare
12150022121500191215002012150024121500251215002312150018121500211215002612150027
usable DIN LH + DIN RH----------
1215002812150029121500301215003112150032
25303540452530354045
24 mm backset29 mm backset34 mm backset39 mm backset44 mm backset
Narrow stile lock 1812
34
Range / Order numbers
Specification text
BKS narrow stile deadbolt lock 1812; stainless steel forend, square, 24 x 3 mm flat forend; galvanized lock case; with assembly friendly guide of thecylinder fixing screw; usable DIN LH + DIN RH; one turn nickel-plated steel deadbolt with 14 mm deadbolt projection, (optionally 5 mm projection); behindbackset 15 mm; 92 mm center distance; ____ mm backset
Narrow stile lock 1812Narrow stile lock 1812
35
Other options (upon request)
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
B 9000 0422“U” shapedforend24 x 6 mm
Narrow stile lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 mm 24 mm forend / 5 mm latch projectionusable DIN LH + DIN RH
Stainless steel
squaresquaresquaresquaresquare
B 1812 0001B 1812 0002B 1812 0003B 1812 0004B 1812 0005
usable DIN LH + DIN RHB 1812 0019B 1812 0020B 1812 0021B 1812 0022B 1812 0023
2530354045
Backset
6.5 (2 pieces from backset 40)
Narrow stile lock 1828
36
Range / Order numbers
Specification text
BKS narrow stile lock 1828; stainless steel, square; flat forend 24 x 3 mm; with latch lever; galvanized lock case; with assembly friendly guide of thecylinder fixing screw; special 9 mm follower, reinforced follower bearing; reversible steel latch, usable DIN LH + DIN RH (optionally 5 mm projection); one turn galvanized steel deadbolt with 14 mm deadbolt projection; 15 mm behind backset; 92 mm center distance; _____ mm backset
Narrow stile lock 1828
37
Other options (upon request)
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
B 9000 0402“U” shapedforend24 x 6 mm
Narrow stile lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 mm 24 mm forend / 5 mm latch + deadbolt projectionusable DIN LH + DIN RH
Stainless steel
squaresquaresquaresquaresquare
B 1828 0001B 1828 0002B 1828 0003B 1828 0004B 1828 0005
usable DIN LH + DIN RHB 1828 0010B 1828 0011B 1828 0012B 1828 0013B 1828 0014
2530354045
38
Product features
Sliding door locks for narrow stile systems
Pivot hook boltProvides a secure closure of the door.
Guiding pinFinds the correct position whenclosing the door.
ForendAs fixing element of the lock with thedoor.The various design scopes of surfacesand shapes must be specified in theorder. Locking method
For profile cylinders.
Lock caseAs stable galvanized design, it protectsthe function of the lock with a smallbehind backset.
BacksetMust be specified inorders.
Product features
39
Special locks for narrow stile systems
Application: Glass doors
Technical features:– profile cylinder lock with latch lever function, 72 mm distance– can be supplied in backsets 25, 30, 35, 40 and 45 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– zinc die-cast latch– one turn steel deadbolt, with 20 mm deadbolt projection– various forend versions in regards to form and optics
Application: Sliding doors
Technical features:– profile cylinder lock with latch lever function, 72 mm distance– can be supplied in backsets 35 and 40 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– steel deadbolt, usable DIN LH and DIN RH– one turn steel deadbolt, with 20 mm deadbolt projection
Application: Sliding doors
Technical features:– profile cylinder lock with latch lever function– can be supplied in backsets 30, 35, and 40 mm– possibility of through fixing of conventional door furniture with oval rose– galvanized lock case– steel deadbolt, usable DIN LH and DIN RH– optional with guiding pin as 1205SRHF to position the door when closing
Sliding door locks 1205SRH + 1205SRHF
Sliding door lock 1205H
Glass door lock 0007
Glass door lock 0007
40
Range / Order numbers
Other options (upon request)
Specification text
BKS glass door lock 0007; nickel-silver painted forend (or stainless steel), square (or rounded); with latch lever; galvanized lock case; with assemblyfriendly guide of the cylinder fixing screw; 8 mm steel wing follower; zinc die-cast latch; one turn galvanized steel deadbolt with 10 mm deadboltprojection; 16 mm behind backset; 72 mm center distance; _____ mm backset
Glass door lock 0007
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
S4010088 (ns)S4010012 (ss)
Stainless steel Rounded forend
41
Glass door lock
ForendSurface
Backsetin mm
ForendForm
Forend 18 mm Forend 20 mm Forend 24 mmDIN LH DIN RH
Steelnickel-silver
squaresquaresquaresquaresquare
0007100100071003000710050007100700071009
0007100200071004000710060007100800071010
DIN LH DIN RH0007107000071011000710130007027100071015
0007017100071012000710140007027200071016
DIN LH DIN RH0007101700071019000710210007102300071025
0007101800071020000710220007102400071026
2530354045
Sliding door lock 1205H
42
Range / Order numbers
Other options (upon request)
Specification text
BKS sliding door lock 1205H with hook latch; nickel-silver painted forend, square; with latch lever; galvanized lock case; with assembly friendly guide ofthe cylinder fixing screw; special 8 mm follower; zinc die-cast steel hook latch, usable DIN LH + DIN RH; one turn galvanized steel deadbolt with 13 mmdeadbolt projection; 16.5 mm behind backset; 72 mm center distance; _____ mm backset
Sliding door lock 1205H
Backsetin mm
ForendFinish Width
Special versions Possible striking platesFollower
9 mmS4910023 (ns)S4910025 (ss)
43
Sliding door lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquare
12050028120500291205006412050104
35403540
Sliding door lock 1205SRH
44
Range / Order numbers
Other options (upon request)
Specification text
BKS sliding door lock 1205SRH with pivot hook bolt; nickel-silver painted forend (or stainless steel), square; galvanized lock case; with assembly friendlyguide of the cylinder fixing screw; galvanized steel pivot hook bolt, usable DIN LH + DIN RH; behind backset 16 mm; _____ mm backset
Sliding door lock 1205SRH
Backsetin mm
ForendFinish Width
Special versions Possible striking platesFollower
S4910029 (ns)S4910030 (ss)
45
Sliding door lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 mmusable DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquare
120501951205019612050204120501971205019812050205
303540303540
Sliding door lock 1205SRHF with guiding pin
46
Range / Order numbers
Other options (upon request)
Specification text
BKS sliding door lock 1205SRHF with pivot hook bolt and guiding pin; nickel-silver painted forend (or stainless steel), square; galvanized lock case; withassembly friendly guide of the cylinder fixing screw; galvanized steel pivot hook bolt, usable DIN LH + DIN RH; steel guiding pin; behind backset 16 mm;_____ mm backset
Sliding door lock 1205SRHF with guiding pin
Backsetin mm
ForendFinish Width Special versions
Possible striking platesFollower
S4910068 (ns)S4910053 (ss)
47
Sliding door lock
ForendSurface
Backsetin mm
ForendForm
Forend 24 mmusalbe DIN LH + DIN RH
Steelnickel-silver
Stainless steel
squaresquaresquaresquaresquaresquare
120501991205020012050206120501901205020112050207
303540303540
48
Door handling
Reversible latch
The following must be observed for locksequipped with a reversible latch:
The screw to reverse the latch is locatedon the back of the lock.Push it outward with the screw driver,reverse the latch and tighten the screwagain in the initial position.
Locks with roller latches are used for swing doors. In order to achieve an ideal fixing function, the rollerlatch position may be changed through the screw located on the front.
Adjustable roller latch
Product advice
Left inwards – DIN leftLever showing to the left
Left outwards = DIN rightLever showing to the left
Right outwards = DIN leftLever showing to the right
Right inwards = DIN rightLever showing to the right
49
In order to disable the latch of a mortise lock during daily operation, a latch fixingdevice may be installed in locks of class 3 + 4 upon request.
A mortise lock with a retracted and fixed latch enables an unchecked door access.
After releasing the fixing device, the latch may then again be operated via the latchlever by using the lever.
Note: The specification text must be supplemented accordingly “...with latch fixingdevice”.
Locks which are intended for Swiss round cylinders (such as KABA, KESO) require thefollowing attention:
The distance from the center of the follower is 2 mm longer than the comparabledimension of profile cylinders.
Example: PZ 92 mm = CH-RZ 94 mm
Special BKS end caps are included in the overall delivery of locks with “U” shapedforends.
The end caps have expanding pins which may be used for the attachment in the pro-file.
These may be removed and pop rivet nuts may be used for a more stable attachment.
Latch fixing device
End caps for “U” shaped forends
Swiss round cylinder
Product advice
Cent
er
Cent
er P
Z
Swis
sRo
und
cylin
der
50
Striking plate B 9000 for series 18 + 19 with flat forend
Striking plate B 9000 for series 18 + 19 with “U” shaped forend
Striking plates
Other options (upon request)
FinishSpecial versions
Suitable for locks:B 1926, B 1974
BKS striking plate (or lipped striking plate) B 9000 forautomatic locking locks of series 19 + narrow stilelocks of series 18 suitable for medium application,square ends; usable DIN LH + DIN RH (lipped strikeplate usable DIN LH + DIN RH)
Other options (upon request)
Finish Special versions
Suitable for locks:B 1926B 1974
BKS striking plate 9000 for automatic locking locks ofseries 19 + narrow stile locks of series 18 with “U”shaped forend; suitable for medium application, “U”shaped forend 24 x 6 mm, with decorative plastic endcaps for an optional attachment with pop rivet nuts orintegrated dowel technology; square ends; usable DINLH + DIN RH
FinishOrder numberfor lock 1812
Order numberfor series 18 + 19
Stainless steel B 9000 0422 B 9000 0402
Finish
Finish
Order number
DIN LHDIN RH
Stainless steel
Stainless steel
B 9000 0435B 9000 0436
Range / Order numbers
Order number
B 9000 0785
Range / Order numbers
Standard version
Range / Order numbersLipped strike plate
51
Striking plate S401 for 0007
Striking plate S491 for 1205/1205H
Striking plates
BKS angular striking plate S401 for glass door lock0007; suitable for light application; round ends
BKS Striking plate S491 for narrow stile lock 1205and 1205H; suitable for normal application, squareends; usable DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:0007
Finish Order number
Steelnickel-silver
Stainless steel
S4010088
S4010012
Range / Order numbers
Other options (upon request)
Finish Special versions
Suitable for locks:12051205H
Finish Order number
Steelnickel-silver
Stainless steel
S4910023
S4910025
Range / Order numbers
52
Striking plate S412 for 1218
Striking plates
BKS striking plate S412 for deadbolt lock 1218;suitable for normal application, square ends; usableDIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1218
Finish Order number
Steelnickel-silver
Stainless steel
S4120026
S4120008 S4120027 (SKG)
Range / Order numbers
BKS “U” shaped striking plate 412 for deadbolt lock1218; with decorative plastic end caps for an optionalattachment with pop rivet nuts or integrated doweltechnique; suitable for normal application, squareends; suitable DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1218
Finish Order number
Stainless steel S4120028
Range / Order numbers
“U” shaped striking plate S412 for 1218
53
Striking plate S491 for 1212
Striking plates
BKS striking plate S491 for narrow stile lock 1212;suitable for normal application, square ends; usableDIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1212
Finish Order number
Steelnickel-silver
Stainless steel
S4910064
S4910040 S4910071 (SKG)
Range / Order numbers
BKS “U” shaped striking plate S491 for narrow stilelock 1212; with decorative plastic end caps for anoptional attachment with pop rivet nuts or integrateddowel technique; suitable for normal application,square ends; suitable for DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1212
Finish Order number
Stainless steel S4910078
Range / Order numbers
“U” shaped striking plate S491 for 1212
54
Striking plate S491 for 1215
Striking plates
BKS striking plate S491 for roller latch lock 1215;suitable for normal application, square ends; usableDIN LH + DIN RH
BKS “U” shaped striking plate S491 for roller latchlock 1215; with decorative plastic end caps for anoptional attachment with pop rivet nuts or integrateddowel technique; suitable for normal application,square form; suitable DIN LH + DIN RH
“U” shaped striking plate S491 for 1215
Other options (upon request)
Finish Special versions
Suitable for locks:1215
Finish Order number
Steelnickel-silver
Stainless steel
S4910065
S4910042
Range / Order numbers
Other options (upon request)
Finish Special versions
Suitable for locks:1215
Finish Order number
Stainless steel S4910077
Range / Order numbers
BKS striking plate S491 for sliding door lock 1205SRHFwith hook and guiding pin; suitable for normalapplication, square ends; usable DIN LH + DIN RH
55
Striking plate S491 for 1205SRH
Striking plates
BKS striking plate S491 for sliding door lock 1205SRHwith hook; suitable for normal application,square ends, usable DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1205SRH
Finish Order number
Steelnickel-silver
Stainless steel
S4910029
S4910030
Range / Order numbers
Other options (upon request)
Finish Special versions
Suitable for locks:1205SRHF
Finish Order number
Steelnickel-silver
Stainless steel
S4910068
S4910053
Range / Order numbers
Striking plate S491 for 1205SRHF
56
Striking plate S491 for 1425
Striking plate S491 for 1426
Striking plates
BKS striking plate S491 for sliding door lock 1425with hook; suitable for medium application,Square ends; usable DIN LH + DIN RH.
BKS striking plate S491 for sliding door lock 1426;suitable for medium application wear, square ends;usable DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1425
Finish Order number
Steelnickel-silver
Stainless steel
S4910046
S4910047
Range / Order numbers
Other options (upon request)
Finish Special versions
Suitable for locks:1426
Finish Order number
Steelnickel-silver
Stainless steel
S4910075
S4910059
Range / Order numbers
57
Striking plate S491 for 1427
Striking plate S491 for 1430
Striking plates
BKS striking plate S491 for sliding door lock 1427 withhook; suitable for medium application, square ends;usable DIN LH + DIN RH
BKS striking plate S491 for sliding door lock 1430with hook; suitable for medium application, squareends; usable DIN LH + DIN RH
Other options (upon request)
Finish Special versions
Suitable for locks:1427
Finish Order number
Steelnickel-silver
Stainless steel
S4910037
S4910038
Range / Order numbers
Other options (upon request)
Finish Special versions
Suitable for locks:1430
Finish Order number
Stainless steel S4910076
Range / Order numbers
The following information regarding locks must be observed in accordance withthe manufacturer's liabilities of his products defined in the product liabilitiesstatute.
Noncompliance releases us from any liabilities.
1. Product information and use as directedA lock generally has the function to lock and block a door. Simple lock designsserve only to lock the door. This designates that a door is kept closed so that itcannot be opened by pulling or pushing, but may be opened by a simple method,such as by moving the lever. The lock latch – generally only called latch – servesas lock.
Securing the closed door by at least one projecting door latch or by blocking of adeadbolt, which meshes into the appropriate recess of the jamb and or the lock-ing plate, is called blocking.
The deadbolt must be blocked against pushing back in its projected position. Inaddition, the door must be effectively difficult to open without the proper key.
The door may only be blocked in a previously closed condition.Cylinder attachment screws must be coordinated or adjusted to the backsetlength.
A mortice lock is a lock which is inserted into a recess in the door leaf (lock pock-et) and screwed on.The following must be observed to assure proper use:- Locks, locking plates, door fittings, attaching devices and locking cylinders
must be matched.
- The current “state of technology” must be applied for a proper installation,the maintenance and possibly a replacement. This is documented in thestandards of these products and in instructions or manufacturer's cata-logues.
Locks for anti-panic doors or special locks generally do not require an immediateuse of keys when activating the door fitting (such as the door lever).Locks for anti-panic doors or special locks may only be combined with lockingcylinders with a so-called turning handles (such as knob cylinders) if this is con-tractually approved by the lock's manufacturer. It is commonly suggested thatonly the owners of the keys have the right to activate the lock, meaning that theactivation of a lock through a knob cylinder (or without a key) is not considered tobe as a normal case.
Simultaneously pulling back the latch and the prelocked deadbolt only by activat-ing the door lever is a special case and may not replace the “normal” key rota-tion to pull back the deadbolt.
Locking cylinder may only be unconditionally installed in locks when they are sub-ject to a dimension standard (DIN 18252) and if such locks are clearly preparedfor locking cylinders under this standard.
In all other cases, the manufacturer, dealer, fabricator or consumer of such locksmust obtain the certainty that the locking cylinders he selected are suitable fortheir intended use.
The necessary legal regulations and manufacturer's instructions must beobserved. For example, no locking cylinders with a button, knob, or a similar han-dle may be installed in anti-panic locks.
General terms, provided these are not explained in catalogue pages, broschures,price lists or on the internet are explained in the standards relevant for theseproducts (such as DIN 18250, DIN 18251, DIN 18252, DIN 18255, DIN 18257, DIN18273, DIN EN 179, DIN EN 1125, DIN EN 1303, DIN EN 1906, DIN EN 12209).Deviations from the particular relevant standard must be specified in the order.
2. Incorrect useAn incorrect use – meaning a product use not as directed – of locks, for exam-ple, is, when- The flawless use is prevented by inserting foreign objects into the lock or into
the locking plate.- When interfering or assaulting the lock or locking plate, which results in a
change of the structure, the effectiveness or the function.- The lock bolt is prelocked to keep the door open.- The closing elements are assembled to be blocked in their function or are
subsequently treated (for example, painted).- If a load is attached to the lever connection which exceeds the normal force
applied by hand.- If unsuitable, such as dimensionally deviating or incorrect keys are being used.- If an expansion or reduction of the required door gap develops when re-
adjusting the hinges or when lowering the door.- If a non-approved double wing door is opened past the inactive wing.- When gripping between the door leaf and the jamb when closing the doors.- when simultaneously activting the lever and the key.
3. Product performanceIf the product performance is not explicitly defined in our catalogues, broschures,price lists, performance specifications, etc., the requirements must be coordinat-ed with us.
The relevant standards serve as guidelines (for example, DIN 18250, DIN 18251,DIN 18252, DIN 18255, DIN 18257, DIN 18273, DIN EN 179, DIN EN 1125, DIN EN1303, DIN EN 1906, DIN EN 12209).
Basic requirements and additional requirements are defined in these standards.
The serviceability of locks also depends of the operating frequency, operatingmethod, environmental effects and maintenance.
Lock, strike plate, door fittings, locking cylinders and keys must be replaced assoon as problems occur despite proper maintenance.This also applies to attempts to forcefully overcome locks and their accessories(burglary attempts).
4. Product maintenanceLocks must be lubricated with suitable lubricants at least once per year – morefrequently after wear. Door fitting, strike plate and locking cylinder must bechecked for their proper condition and their installation. Only cleaning materialthat do not contain any corrosion-promoting ingredients may be used.
5. Information and instruction dutiesThe following documents and services are available to specialty dealers, lock-smiths, architects, planners, fabricators and users upon request, in order to com-ply with the informational and instructional duties of the product liability statutes:- Catalogues, broschures- Specification texts copies, quotation documents, keying plans- The relevant standards serve as guidelines, for example, DIN 18250, DIN
18251, DIN 18252, DIN 18255, DIN 18257, DIN 18273, DIN EN 179, DIN EN1125, DIN EN 1303, DIN EN 1906, DIN EN 12209 (Exclusive selling rights ofthe Beuth Verlag GmbH, Berlin 30).
- Instructions for installation, operation and maintenance
For the selection of locks and the installation, operation and maintenance,- architects and planners should consider to request and observe all required
product information from us.- Specialty dealers must consider to observe product information and refer-
ence in the price lists and specifically request all necessary instructions fromus and to forward these to the fabricators.
- Fabricators must consider to observe all product information and specifical-ly request operating and maintenance instructions from us and to forwardthese to contractors and consumers.
Product information for locks
58
59
Product information for locks
General use,
installation and
maintenance advice for
BKS-locks and furniture
1. The door leaf should not be drilled in the area ofthe lock installed.
2. The spindle should not be knocked through the follower using a hammer.
5. The latch bolt and dead bolt should not be paintedover.
4. The distance between forend and strikershould be between 2 and 5 mm.
3. The door leaf should not be carried using the handles.
2 to 5 mm
Product information for locks
60
8. The dead bolt should not be extendedwhile the door is open.
9. The handle and the key should not be operated simultaneously.
10. Anti-panic locksshould not be leftwith a key in them.
11. Anti-panic locks should not be fittedwith locking cylinders with thumb turnor turn knob.
6. The handle should not be operated in the wrong direction. In use a maximumload of 150 N on the handle shouldnot be exceeded.
7. The lock should not be operated withany foreign objects.
Product information for locks
61
Exclusion of liability
The BKS products are permanently adapted to growing market's requirements and developed further.We also reserve for changes serving the technological progress.
This necessity is based on:– technical development– change and adaptation in product range– adaptation to changed laws and technical standards.
We have arranged the content of our documents with the greatest possible care.We therefore ask for your understanding that we take no responsibility for possible mistakes with regard to presentation and description of the products.Many thanks for your understanding.
12. Panic doors should only be used in case ofemergency (no frequent use).
13. Double leaf doors should not be forcedopen using the inactive leaf.
14. As soon as there are visible signs of physicalattack (e.g. bent bolts), the lock must be replaced.
15. Locks are to be lubricated at least oncea year (non-resinogenic oil).
year
DIN 107Description left and right in the construction industry
DIN 1080, part 1Terms, symbols and units in civil engineering, basics
DIN 4102, part 5 + 18Part 5: Fire performance of building materials and components; firebarriers, barriers in elevator shaft walls and fire-resistant glazingPart 18: Fire performance of building material and components; firebarriers; proof of “self-locking” properties (continuous operation test)
DIN 18 055Windows; joint impermeability, water penetration resistance andmechanical stress; specifications and tests
DIN 18 082, part 1 +3Part 1: Fire barriers, steel doors T30-1, model APart 3: Fire barriers, steel doors T30-1, model B
DIN 18 095, part 1 +2Part 1: Doors; smoke protection doors; terms and specificationsPart 2: Doors; smoke protection doors; design test of the long-termoperational reliability and weathertightness
DIN 18 100Doors; wall openings for doors; Dimensions compliant with DIN 4173
DIN 18 101Doors, doors for apartment construction; door leaf sizes, hinge seatingand lock seating; interrelationship between dimensions
DIN 18 111, part 1Door jambs, steel jambs, standard jambs for rebated doors
DIN 18 250Mortice locks for fire barriers
DIN 18 251Locks; mortice locks for doors
DIN 18 252Locking cylinders for door locks; terms, descriptions
DIN 18 255Building hardware; door handles, doorplates and door rosettes – terms,dimensions, specifications
DIN 18 257Building hardware; protective coatings – terms, dimensions, specifi-cations, tests and identifications
DIN 18 273Building hardware; door handle sets for fire barriers and smoke pro-tection doors – terms, dimensions, specifications and tests
DIN 18 357Official Contracting Terms for the Award of Construction PerformanceContracts Part C: General technical contract requirements for con-struction services (General Pricing Regulations) Fitting operations
DIN 18 361Official Contracting Terms for the Award of Construction PerformanceContracts Part C: General technical contract requirements for con-struction services, glazing operations
DIN 68 706 part 1Interior doors of wood and wood materials, barrier door leaves, terms,prefered dimensions, structural features
DIN EN 179Emergency exit locks with handle or joint plate
DIN EN 1125Anti-panic door locks with horizontal control bar
DIN EN 1154Door closing device with controlled closing process
DIN EN 1303Building hardware – locking cylinders for locks – specifications andtesting procedures
DIN V ENV 1627Windows, doors, fittings – burglary prevention – specifications andclassification
DIN V ENV 1628Windows, doors, fittings – burglary prevention – testing procedures tocalculate the resistance under static stress
DIN V ENV 1629Windows, doors, fittings – burglary prevention – testing procedures tocalculate the resistance under dynamic stress
DIN V ENV 1630Windows, doors, fittings – burglary prevention – testing procedures tocalculate the resistance to counter manual burglary attempts
DIN EN 1634 Part 1 + 3Fire resistance tests for door and connecting devicesPart 1: Fire barriersPart 3: Smoke protection barriers
DIN EN 1906Building hardware, door handles, and door knobs – specifications andtesting procedures
The most diverse standards and specifications exist for doors and related products. The most important are listed in the following:
Relevant standards
62
A complete Quality Assurance System in correspondence with DIN EN ISO 9001 guarantees consistently high quality of allprocesses at BKS.
This Quality Assurance standard applies the highest demands at the European level and is not relative to production, but also to otherbusiness sectors such as research, order processing or customer service. This standard applies to all manufacturing sections at BKS(locking cylinders, door locks, fittings, electronics and door closers).
The extensive product range of the G.U-BKS group is designed for heavy-duty use and coordinated.
The high performance level in regards to quality, dependability and long life can only be assured when coordinated products are used.The program variety of the G. U-BKS group makes it possible to use this advantage.
This is documented by the appropriate tests and registrations, relative to the standards and specifications.These certificates may be requested, if desired.
Quality
63
1. General / Scope of Application
1.1 Our Sales Terms and Conditions are exclusively applicable; we do not recognise con-trary terms and conditions by the Purchaser or terms and conditions deviating fromour Sales Terms and Conditions unless they have been explicitly approved by us in wri-ting. Our Sales Terms and Conditions shall be applicable even if we carry out deliveryto the Purchaser without reservation and with the knowledge of contrary terms andconditions or terms and conditions deviating from our Sales Terms and Conditions.
1.2 All agreements made between us and the Purchaser in view of performance of thepresent contract have been stipulated in writing in the present contract.
1.3 Our Sales Terms and Conditions are only valid vis-à-vis a contractor within the mean-ing of § 14 BGB [German Civil Code].
1.4 Our Sales Terms and Conditions shall also be valid for subsequent orders. For currentand future business relations the Sales Terms and Conditions shall be valid as frame-work terms and conditions even if not explicitly agreed upon in future.
1.5 In addition to our General Terms and Conditions our "Installation Guidelines", "Installa-tion Instructions" and “Product Informations” shall be valid.
2. Offer / Offer Documentation
2.1 Our offer is subject to alterations unless otherwise specified in the order confirmation.After a purchase order has been placed by the customer, a contract is entered into byour written order confirmation. The contents of the contract shall be governed by ourwritten order confirmation.
2.2 Warranty of a quality or acceptance of an independent guarantee on contract conclu-sion moreover must be explicitly identified in writing accordingly.
2.3 Subsequent modifications of the contract contents must also be made in writing. 2.4 We reserve property rights and copyrights in illustrations, drawings, calculations and
other documents; they must not be made available to third parties. This is especiallyapplicable to such written documents identified as being "confidential". Prior to theirtransmittal to third parties the Purchaser requires our explicit written approval.
3. Prices / Payment Terms and Conditions
3.1 Unless otherwise specified in the order confirmation, our prices are to be understood"ex works" excluding packing and transport charges, insurance and other contingen-cies; these shall be invoiced separately.
3.2 For pieces or parts which we produce on a special demand or order of the Purchaserwe inform the Purchaser about the amount of the production.
3.3 Statutory value-added tax is not included in our prices; it will be shown separately onthe invoice on the day of invoicing in the amount stipulated by law.
3.4 Discount deduction requires a special written agreement. Independent of such a writ-ten agreement it is stipulated that a discount of 3 % on the net invoice value shall begranted if payment is received within 10 days as from date of invoice. If payment isreceived within 30 days, we will grant 2 % discount on the net invoice value. No dis-count will be granted on new invoices as long as still open balances from former invo-ices exist. Payments will always be used for settlement of the oldest debit item.
3.5 Unless otherwise specified in the order confirmation, the purchase price is due forpayment net (without deduction) within 60 days as from date of invoice. If thePurchaser defaults, we shall be entitled to request arrears on interest in the amount of8 % above the respective basic interest published. But the Purchaser shall be entitledto prove to us that no damage or a damage of a far minor importance has occurred forus as a result of the delay of payment.
3.6 The Purchaser shall only be entitled to setoff rights if his counterclaims have legalforce, are undisputed or have been recognised by us. The Purchaser shall be entitledto exercise a general lien in so far as his counterclaim is based upon the same con-tractual relationship.
3.7 We shall not be obliged to accept bills of exchange or cheques. If cheques or bills ofexchange are accepted on a case to case basis upon prior agreement, this will only bemade in fulfilment by invoicing the discount charges and collection charges whichhave to be paid by the customer immediately in cash. Accepted bills and cheques willbe finally credited after having been honoured. Acceptance of cheques or bills ofexchange will be made without prejudice for later payment obligations. We shall notbe responsible for timely presentation, protest and return of the bill of exchange, if ithas not been honoured.
3.8 If a bill of exchange or a cheque is not honoured in time or if a payment term grantedis exceeded, all debts still open at that time – also debts for which a respite has beengranted and debts for which bills of exchange or cheques have been given – becomeimmediately due for payment.
4. Delivery / Delivery Time
4.1 Prior to start of the delivery time indicated by us all technical questions must havebeen clarified. If we inform the Purchaser about delivery times these informations arenot binding and show only a foreseeable delivery time.
4.2 Observance of our delivery obligation moreover requires timely and orderly fulfilmentof the Purchaser's obligations, especially observance of the agreed upon paymentterms and conditions. The defence of a non-fulfilled contract remains reserved.
4.3 If the Purchaser has been put on notice to take delivery or if he violates any otherduties of co-operation, we shall be entitled to request indemnification of the damageincurred to us to that extent including eventual surplus expenditure. Further claimsremain reserved.
4.4 If the prerequisites of item 4.3 exist, the risk of an accidental destruction or an acci-dental deterioration of the object purchased passes onto the Purchaser at that point intime when the Purchaser has been put on notice to take delivery or is in debtor's delay.
4.5 If non-observance of the delivery time is due to Force Majeure such as for examplemobilization, war, riot or similar incidents such as for example strike, lock-out, thedelivery time is extended by the duration of the incidents causing the delay in so faras these impediments can be proven to have a major influence on completion or deli-very. The same applies if these circumstances occur at sub-suppliers.
4.6 Partial deliveries are admissible within a reasonable extent. 4.7 We shall be liable in general only for delay in delivery in accordance with statutory pro-
visions of the German Commercial Code and the German Civil Code. 4.8 Moreover we shall be liable in accordance with statutory provisions in so far as the
delay in delivery is based upon an intentional or grossly negligent contract violationfor which we are responsible; we shall also be responsible for a fault caused by ourrepresentatives or vicarious agents.
4.9 In so far as the delay in delivery is merely based upon simple fault and no mandatoryliability is applicable due to violation of life, body or health, our liability for defaultdamages is limited in such a way that the Purchaser can request each 0.5 percent foreach completed week of delay but in total not more than 5 percent of the price for thatdelivery portion which due to the delay could not be put into useful operation. This isnot connected with a modification of the burden of proof to the Purchaser's disad-vantage. The Purchaser's legal right to rescind remains unaffected.
4.10 Goods which have been reported to be ready for shipment have to be called by thePurchaser immediately but not later than after a delay of 20 calendar days after havingbeen informed of the readiness for shipment. If no call occurs, we shall be entitled toput the goods on stock and store them upon our own discretion at Purchaser's riskand treat them as delivered ex works.
4.11 If shipment or delivery of the goods is delayed on request or upon instigation of thePurchaser, storage charges may be invoiced starting from one month after notificationof readiness for shipment in the amount of 1% of the invoice value for each monthstarted. The storage charges shall be limited to 5 % of the invoice value unless higherstorage charges can be proven by us.
4.12 Fulfilment of our obligation in accordance with the German Packaging Regulations hasbeen transferred by us to a authorized Company who sets up appropriate collectingboxes for packing material which has to be taken back in places where large quanti-ties and small quantities of packing material occurs. Overwraps and sales packageswill be taken back by us only via this authorized Company. Outside the scope of appli-cation of the Packaging Regulations no packing material will be taken back by us.
5. Participation Duties of our Customers
5.1 Participation services by the customer which are explicitly or tacitly agreed upon wit-hin the scope of the contract will be performed without special remuneration unlessspecified otherwise.
5.2 The customer shall be obliged to inform us on all facts in time from which it resultsthat stock and products in store with us which have been placed at disposal in view ofproduction capacities reported to us cannot be used or cannot be fully used. If resi-dual stock remains, the customer will accept the stock and eventual charges for theirdestruction in case of premature modification of his disposition. The same applies alsoto products for which we had to order minimum quantities from our suppliers in sofar as we had pointed out this fact to our customer in advance.
5.3 The customer guarantees that the products supplied by him for further processing aresuitable for this purpose. We are not obliged to inspect the products supplied by thecustomer for their property and fitness in view of further processing. Within the scopeof current business relations as well as when a processing item has primarily beeninspected, tested and released, the customer shall be obliged to inform us of his ownaccord about each product change. In cases of current processing of items the custo-mer shall be further obliged – for each modification of the production conditions in hisplant especially when replacing tools, machines or when introducing new productionprocedures – to inspect the item to be processed by us for variations and modifica-tions and to inform us in writing of such variations and modifications.
5.4 We shall not be obliged to check the correctness of instructions given by our custo-mers, material selection or other provisions made by our customer.
5.5 Therefore the customer must check all instructions he is giving as well as the qualityof the materials specified or made available to us for compliance with statutory andtechnical provisions.
5.6 If the customer defaults regarding his duty of procurement or participation after writ-ten request, we shall be entitled to statutory rights.
5.7 The taking back of goods requires an explicit written approval, if we are not obligateto take back the goods by law.
6. Passing of Risk
6.1 Unless otherwise specified in the order confirmation, delivery shall be deemed to beagreed upon "ex works".
6.2 The risk for delivery passes onto the customer when leaving our works, at the latestwith shipment of the consignment and/or delivery to the carrier or forwarding agenteven if partial deliveries are made or if exceptionally we carry out transport at our ownexpenses or with our transportation means unless otherwise specified.
6.3 If shipment is delayed due to circumstances for which the customer is responsible, therisk passes onto the customer with receipt of the notification of readiness for ship-ment.
6.4 Return shipments must be returned to us carriage-free. In case of return shipment therisk of loss remains with the customer until the products have been accepted at ourworks.
6.5 If the customer so requests, we will effect a transport insurance for the shipment; thecharges connected with it will be borne by the customer.
General Terms and Conditions
General Sales, Delivery and Payment Terms and Conditions
64
7. Redhibitory Defects
We shall be liable for redhibitory defects as follows:7.1 All such parts or services have to be reworked, newly delivered or rendered again free
of charge upon our choice which within the statutory limitation – irrespective of theoperating period – show a redhibitory defect in so far as its cause existed at the timeof passing of risk.
7.2 Claims due to redhibitory defects become barred by the statute of limitations in 12months. The time period starts with the passing of risk (item 6).
7.3 The customer must notify the redhibitory defect to us immediately in writing.7.4 In case of notification of defects payments by the customer are permitted to be with-
held within a scope which is in an adequate ratio to the redhibitory defects occurred.The Purchaser shall only be allowed to withhold payments if a notification of defectshas been put forward the justification of which cannot be doubted. If the notificationof a defect was wrong, we shall be entitled to request indemnification of expendituresincurred by us from the customer.
7.5 First of all we shall always be granted the possibility of subsequent performance withinan adequate delay.
7.6 If subsequent performance fails, the Purchaser may withdraw from contract – withoutprejudice to eventual damage claims – or reduce payment. Replacement for fruitlessexpenditure can only be requested by the Purchaser, if we are responsible for thedefect due to intent or gross negligence.
7.7 Claims as a result of defects do not exist in case of only minor variation from theagreed upon quality, in case of only minor impairment of usefulness, in case of natu-ral wear and tear or damages occurring after passing of risk due to wrong or negligenttreatment, excessive load, inappropriate consumables or due to special externalinfluences which are not presumed according to contract as well as in case of non-reproducible software errors. If the Purchaser or third parties carry out modificationsor repair work in an inappropriate way, no claims as a result of defects exist for it andthe resulting consequences either. The same applies in so far as our specifications forhandling and other instructions are not observed.
7.8 Claims by the Purchaser for expenditure necessary for the purpose of subsequent per-formance including but not limited to transport, road, work and material charges areexcluded to the extent that the expenditure increases because the object of deliveryhas subsequently been taken to another place than the establishment of the Purchaserunless this change of location corresponds to its use according to purpose.
7.9 Legal recourse claims by the Purchaser towards us exist only in so far as the Purchaserhas not made any agreements with his customer beyond statutory claims due to defects.
7.10 For damage claims item 9 applies. Further or other claims than those stipulated in thisitem or in item 9 for redhibitory defects are excluded.
8. Industrial Property Rights and Copyrights, Defective Titles
Unless otherwise agreed upon, we shall be obliged to render delivery only in the coun-try of the place of delivery free from industrial property rights and copyrights by thirdparties (hereinafter called property rights). In so far as a third party due to violation ofproperty rights by deliveries rendered by us and used according to contract, puts for-ward justified claims against the Purchaser, we shall be liable to the Purchaser withinthe delay determined in item 7.2 as follows:
8.1 Upon our choice and at our own expenses we will either obtain a right of use (usu-fructuary right) for the deliveries concerned, modify them in such a way that the pro-perty right will not be violated or replace them. If this is not possible for us under ade-quate terms and conditions, the Purchaser shall be entitled to statutory rights of with-drawal or reduction. The Purchaser shall only be allowed to request indemnificationfor fruitless expenditure, if we are liable for intent or gross negligence. Our obligationto pay damages is governed by item 9.
8.2 The above mentioned obligations exist only in so far as the Purchaser informs usimmediately in writing about the claims put forward by the third party, does not recog-nise a violation and all defences and composition proceedings are reserved for us. Ifthe Purchaser ceases to use the delivery for reasons of damage reduction or for otherimportant reasons, he shall be obliged to inform the third party that no acknowledge-ment of a violation of property rights is connected with it.
8.3 Claims of the Purchaser are excluded in so far as he is responsible for the violation ofproperty rights.
8.4 Claims of the Purchaser are also excluded in so far as the violation of property rightsis caused by particular specifications of the Purchaser, by an application unforeseea-ble by us or by the fact that the delivery is modified by the Purchaser or used toget-her with products not delivered by us.
8.5 In case of violations of property rights for the claims of the Purchaser stipulated initem 8.1 the provisions of items 7.4, 7.5 and 7.9 apply accordingly.
8.6 Further claims of the Purchaser or other claims of the Purchaser than those stipulatedin the present item 8 against us or our vicarious agents for defective title are excluded.
9. Total Liability
9.1 Claims by the Purchaser for indemnification – irrespective of the legal nature of theclaim put forward – are excluded.
9.2 Excluded from this provision are:a) Damages due to violation of substantial contractual obligations. In case of simple
negligence, however, liability for indemnification shall be limited to the foreseeabledamage typically occurring.
b) Damages due to violation of life, body or health if we are responsible for the breachof duty.
c) For other damages based upon an intentional or grossly negligent breach of dutywith us being equally responsible for a breach of duty by our legal representativesor vicarious agents.
d) Indemnification for impossibility or inability.
9.3 No modification of the burden of proof at the Purchaser's disadvantage is connectedwith the above provision.
9.4 Liability according to the liability for products' law remains unaffected.9.5 In so far as liability for indemnification towards us is excluded or restricted, this
applies also to personal liability for indemnification by our employees, our commerci-al agents and our vicarious agents.
10. Retention of Title
10.1 The objects of the deliveries (goods under retention of title) remain our property untilpayment of all debts to which we are entitled from the business relationship. In so faras the value of all securities to which we are entitled towards the Purchaser exceedsthe amount of all claims secured by more than 10 %, we will release a correspondingshare of the securities on request by the Purchaser.
10.2 During existence of the retention of title the Purchaser shall not be permitted toencumber the goods or pledge them as security and resale is only permitted to resel-lers in normal dealings and only with a proviso that the reseller receives payment fromhis customer or makes the reservation that transfer of title will only occur if the custo-mer has met his payment obligations.
10.3 In case of attachments, seizures or other orders or interference by third parties thePurchaser must inform us immediately so that we can institute a claim according to §771 ZPO [German Civil Practice Act]. In so far as the third party is not able to reim-burse the court costs and extrajudicial costs of a claim according to § 771 ZPO, thePurchaser shall be liable for the loss incurred by us.
10.4 The Purchaser is obliged to take good care of the item purchased; especially he is obli-ged to insure the item purchased at his own expenses sufficiently at original valueagainst fire, water and theft. In so far as maintenance and inspection work are requi-red, the Purchaser must carry out such work in time at his own expense.
10.5 In case of breaches of duty by the Purchaser including but not limited to delay of pay-ment, we shall be entitled to withdrawal and taking back; the Purchaser is obliged torestitution. Withdrawal and/or exercise of the retention of title does not require rescis-sion by the Supplier; these actions or an attachment of the goods under retention oftitle by us does not represent a withdrawal from contract unless this has explicitlybeen declared by us.
10.6 If the Purchaser has resold the purchased item in the ordinary course of business, heassigns, however, to us already now all debts in the amount of the final invoice value(including value-added tax) of our debts accruing for him from resale against hiscustomers or third parties regardless of whether the purchased item has been resoldwithout or after further processing. The Purchaser remains authorised to collect thisdebt also after assignment. Our authority to collect the debt ourselves remains unaf-fected. But we undertake not to collect the debt as long as the Purchaser meets hispayment obligations from the proceeds taken in, does not default in payment and inparticular no petition for opening of insolvency proceedings has been filed or insol-vency exists. But if this is the case, we can request that the Purchaser informs usabout the debts assigned and their debtors, gives all information necessary for collec-tion, hands out the respective documents and informs the debtors (third parties) of theassignment.
10.7 Processing or reshaping of the purchased item by the Purchaser will always be madeon behalf of us. If the purchased matter is processed with other objects not belongingto us, we acquire joint ownership in the new object in the ratio of the value of the pur-chased item (final invoice value including value-added tax) to the other processedobjects at the time of processing. For the object created by processing moreover thesame applies as for the purchased item delivered under retention of title.
10.8 If the purchased item is mixed inseparably with other objects not belonging to us, weacquire joint ownership in the new item in the ratio of the value of the purchased item(final invoice value including value-added tax) to the other mixed objects at the time ofmixing. If the mixing occurs in such a way that the item of the Purchaser has to beconsidered the main item, it is deemed to have been agreed upon that the Purchasertransfers pro rata joint ownership to us. The Purchaser holds in custody for us theexclusive ownership or joint ownership thus created.
11. Place of Performance, Venue, Governing Law
11.1 For all rights and duties resulting from our deliveries and services for both parties theregistered office of our company shall be considered to be the place of performance.
11.2 In dealings with companies for lawsuits for which the district courts have jurisdictionin rem, the Velbert District Court, and for lawsuits for which county courts have juris-diction in rem, the Wuppertal County Court shall have general jurisdiction.
11.3 The contractual relationship shall be governed by the law of the Federal Republic ofGermany. Application of the UN Convention on Contracts for the International Sale ofGoods (CISG) is excluded.
11.4 The data specified by the Purchaser will be stored and processed by electronic dataprocessing to the extent that this is admissible in accordance with the Federal GermanLaw on Data Protection (§§ 28, 29 BDSG).
11.5 Should any provision of the agreement, the general sales, delivery and payment termsand conditions or other included terms and conditions be or become invalid, in wholeor in part, for any reasons whatsoever, or there is a whole, the validity of the remai-ning provisions shall not be affected thereby. The invalid provision shall be substitu-ted by a valid provision that comes as closely as legally permissible to what the inva-lid provision was intended to achieve.
General terms and conditions
65
General business terms ....................................................................................................................................................................................................64 + 65
Automatic locking locks ......................................................................................................................................................................................................8 – 11
End caps for “U” shaped forend ............................................................................................................................................................................................ 49
Latch fixing device ................................................................................................................................................................................................................ .49
Glass door lock 0024 ........................................................................................................................................................................................................40 + 41
Hook latch locks................................................................................................................................................................................................................16 - 23
Standards.............................................................................................................................................................................................................................. 62
Contract mortise locks ......................................................................................................................................................................................................24 - 33
Product information for locks ............................................................................................................................................................................................58 - 61
Product features – contract mortise locks ........................................................................................................................................................................24 + 25
Product features – special locks ......................................................................................................................................................................................38 + 39
Product features – Safety locks ..........................................................................................................................................................................................6 + 7
Quality .................................................................................................................................................................................................................................. 63
Sliding door locks..............................................................................................................................................................................................................42 - 47
Striking plates ..................................................................................................................................................................................................................50 - 57
Striking plate B9000 ............................................................................................................................................................................................................ 50
Striking plate S401 for lock 0007.......................................................................................................................................................................................... 51
Striking plate S412 for lock 1218.......................................................................................................................................................................................... 52
Striking plate S491 for lock 1205/1205H ............................................................................................................................................................................. 51
Striking plate S491 for lock 1212.......................................................................................................................................................................................... 53
Striking plate S491 for lock 1215.......................................................................................................................................................................................... 54
Striking plate S491 for lock 1205SRH .................................................................................................................................................................................. 55
Striking plate S491 for lock 1205SRHF ................................................................................................................................................................................ 55
Striking plate S491 for lock 1425.......................................................................................................................................................................................... 56
Striking plate S491 for lock 1426.......................................................................................................................................................................................... 56
Striking plate S491 for lock 1427.......................................................................................................................................................................................... 57
Striking plate S491 for lock 1430.......................................................................................................................................................................................... 57
Lock 0007 ........................................................................................................................................................................................................................40 + 41
Lock 1200 ........................................................................................................................................................................................................................26 + 27
Lock 1200RF ....................................................................................................................................................................................................................28 + 29
Lock 1205 ........................................................................................................................................................................................................................30 + 31
Lock 1200H ......................................................................................................................................................................................................................42 + 43
Lock 1200SRH ..................................................................................................................................................................................................................44 + 45
Lock 1205RHF ..................................................................................................................................................................................................................46 + 47
Lock 1212 ........................................................................................................................................................................................................................12 + 13
Lock 1215 ........................................................................................................................................................................................................................32 + 33
Lock 1218 ........................................................................................................................................................................................................................14 + 15
Lock 1425 ........................................................................................................................................................................................................................16 + 17
Lock 1426 ........................................................................................................................................................................................................................18 + 19
Lock 1427 ........................................................................................................................................................................................................................20 + 21
Lock 1430 ........................................................................................................................................................................................................................22 + 23
Lock 1812 ........................................................................................................................................................................................................................34 + 35
Lock 1828 ........................................................................................................................................................................................................................36 + 37
Lock 1926 – automatically locking......................................................................................................................................................................................8 + 9
Lock 1974 – manually locking ..........................................................................................................................................................................................10 + 11
Swiss round cylinder ............................................................................................................................................................................................................ 49
Pivot hook deadbolt locks..................................................................................................................................................................................................42 - 47
Security locks......................................................................................................................................................................................................................6 - 23
Special locks ....................................................................................................................................................................................................................34 - 51
Door handling........................................................................................................................................................................................................................ 48
Reversible latch..................................................................................................................................................................................................................... 48
Adjustable roller latch .......................................................................................................................................................................................................... 48
Gretsch-Unitas GmbHBaubeschlägeJohann-Maus-Str. 371254 DitzingenTelephone: +49 - (0)7156 301 - 0Fax: +49 - (0)7156 301 - [email protected] W
023
0 00
02
10/2
004
my
Prin
ted
in G
erm
any
BKS GmbHHeidestr. 7142549 VelbertTelephone: +49 - (0)2051 201 - 0Fax: +49 - (0)2051 201 - 431www.bks.de