FX742 - NESSA, Inc...59 365-004 4 MLGBushing1.75x1.25x1.5lg 60 257-045 8 Insert,1/2",.063-.200Wall...

®

FX742ROTARY CUTTERS

Published: 2/11 Part No. C742-010PS/N C74210042102 – C74210046102 inclusive

PARTS MANUALAn Operators Manual with IMPORTANT Safety, Assembly,Operation andMaintenance informationwas packagedwith thisParts Manual during final inspection at the factory. If theOperatorsManual ismissing at any time, please contact SchulteIndustries Ltd. At (306) 287-3715 to receive your freereplacement manual.

Si No Lee Ingles, PidaAyuda a Alguien

Que Se Lo Lea Para Que leTraduzca Las

Medidas de Seguridad

¡ATENCIÓN!LEA EL INSTRUCTIVO

Schulte Industries Ltd.PO Box 70Englefeld SaskatchewanCanada S0K 1N0Tel. (306) 287-3715Fax. (306) 287-3355Parts Fax. (306) 287-4066Email: [email protected]: www.schulte.ca © 2011 Alamo Group

mailto:[email protected]

http://www.schulte.ca

LUKE HP

NESSA LABEL

Parts Ordering GuideThe following instructions are offered to help eliminate delay and error in processing purchaseorders for the equipment in this section.

1. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for whichthe parts were ordered.

2. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the description of the part.

3. Schulte Industries Ltd reserves the right to substitute parts where applicable.

4. Schulte Industries Ltd reserves the right to change prices without prior notice.

NOTE: Please refer to the Safety Section in the front of the Operators Manual for the properPart Number when ordering Replacement Safety Decals. Safety decals are availablefree of charge from the Schulte Parts Department.

NOTE: If the Operators Manual does not accompany this Parts Manual please obtain one, freeof charge from the Schulte Parts Department. DO NOT operate this implement unlessyou READ, UNDERSTAND, and FOLLOW the Safety and Operation instructionscontained in the Operators Manual

NOTE: Please note that the appearance of some parts may vary from the artwork shown inthe Manual.

For maximum safety and to guarantee optimum product reliability, always usegenuine Schulte Parts. The use of inferior replacement parts may cause prematureor catastrophic failure, which could result in serious injury or death.Direct any questions regarding parts to:

Schulte Industries Ltd ®P.O. Box 70

Englefeld, SaskatchewanCanada S0K 1N0

Phone: (306)-287-3715Parts Fax: (306) 287-4066

Email: [email protected]

®

mailto:[email protected]

FX742-Center Section..............................................................................................................................1FX742-Inner Left Wing..............................................................................................................................3FX742-Inner Right Wing...........................................................................................................................5FX742-Outer Wings - Left.........................................................................................................................7FX742-Outer Wings - Right.......................................................................................................................9FX742-Front Hitch...................................................................................................................................11FX742-Center Wheel Standard...............................................................................................................13FX742-Wheel Standards - Left...............................................................................................................15FX742-Wheel Standards - Right.............................................................................................................17FX742-Front Castor Wheels...................................................................................................................19FX742-Hub & Tire...................................................................................................................................21FX742-Blade Carriers.............................................................................................................................23FX742-Fixed Blade Shredding, Updraft Blades......................................................................................24FX742-Fixed Knife Shrouding.................................................................................................................25FX742-Fixed Knife Mounts Overhead.....................................................................................................27FX742-Fixed Knife Mounts.....................................................................................................................29FX742-Chain Guards..............................................................................................................................31FX742-Full Belting..................................................................................................................................33FX742-Front Belting With Full Chains.....................................................................................................35FX742-Phasing Circuit............................................................................................................................37FX742-Wing Lift Circuit...........................................................................................................................39Hydraulic Cylinder, 100-440....................................................................................................................41Hydraulic Cylinder, 100-441....................................................................................................................42Hydraulic Cylinder, 100-3685, 100-3695, 100-4075...............................................................................43FX742-Driveline Layout..........................................................................................................................45Driveline, 340-1002 - Tractor Shaft.........................................................................................................47Driveline, 340-651 - Center.....................................................................................................................49Driveline, 340-652...................................................................................................................................51Driveline, 340-860 - Outer Wing.............................................................................................................53Driveline, 340-900...................................................................................................................................55Driveline, 340-1001.................................................................................................................................57Gearbox, 330-866 - Center.....................................................................................................................59Gearbox, 330-867 - Inner Left, Outer Right............................................................................................61Gearbox, 330-868 - Inner Right, Outer Left............................................................................................63Gearbox, 330-869 - Outer Right & Left...................................................................................................65Gearbox, 330-936 - Divider Box, Center.................................................................................................67Gearbox, 330-557 - Inner Right & Left....................................................................................................69FX742-Transport Lights..........................................................................................................................71Safety Chain S000-012...........................................................................................................................72

Part Index................................................................................................................................................73

C742-010P - Page iii - 2/11© 2011 Alamo Group Inc.

TABLE OF CONTENTS

1863 61

63

62

56

7

17

54

53

3837

1

53

89

54 55

5758

2

3

4

5

4

3

2

35

35

5251

41

4039

63

29 30 2855

29

53

29 31 23

31

29

4520

46

39

19

16

18

48

15

34

21

26

59

31

32

49

44

34

48

47

42

50

11

13

15

25

42

6

36

24

33

60

59

30

C742-010P - Page 1 - 2/11© 2011 Alamo Group Inc.

FX742-CENTER SECTION

DescriptionQtyPart No.Ref.FX742 CENTER SECTION1C742-1011FX742 CENTER HINGE PIN4C742-1912SLEEVE, HINGE LINE4C742-1933FILLER PIPE FX7424C742-1954PIN, 1 1/4" X 122C742-1945DIVIDER GEARBOX, 1.35:1 RATIO1330-9366GEARBOX, BP S3125 1.28:1 RATIO1330-8667MOUNT, SKID SHOE, FORWARD2C306-1388SKID SHOE, CENTER2C306-1379FX742 CENTER LOCK UP RECEIVER1C742-17011FX742 CENTER LOCK UP1C742-17113FX742 WING LOCK UP ARM2C742-20315FX742 WING LOCK UP STAND, LEFT1C742-20116FX742 WING LOCK UP STAND, RIGHT1C742-20217FX742 WING LOCK UP PIN2C742-18518SMV MOUNT BRACKET1C000-01319SMV SIGN, 22 GA GALVINIZED1S000-11020PLASTIC CAP, 3" HOLE1280-15121WING LIFT PIN1C520-16823FX742 CENTER TRANSPORT PIN1C742-18824PLASTIC GRAB HANDLE 1 5/16 RED2280-15525CLEVIS PIN, 1 X 2-3/8"1302-01426FX742 INNER WING LIFT PIN2C742-18128ROLL PIN 3/8 X 2 PLATED6262-00629MACHINE BUSHING 1-1/4 I.D. X 1-7/8 O.D. X 10GA4256-07130WASHER 1 PLATED SAE3256-00131COTTER PIN 3/16 X 1-1/2 PLATED1271-00532LINCH PIN, 1/4 STANDARD1300-01233SPACER 3/4 O.D. X .51 I.D. X 5/16 LONG4C742-21434ROLL PIN 3/8 X 2-1/4 PLATED4262-01235BOLT, M8, 20 MM LONG16251-00836LOCKWASHER 5/16 PLATED16255-01537WASHER 5/16 PLATED ASME WIDE16256-02038Bolt: 3/8 x 3/4 UNC: GR5: plated:6250-01739LOCKWASHER 3/8 PLATED4255-01340WASHER 3/8 PLATED ASME WIDE4256-01741LOCKNUT 3/8 UNC PLATED6270-01742QUICK PIN, 5/16 X 3-1/2" U.L.2302-03544BOLT, 1/4 X 3/4 UNCE GR52250-002145LOCKNUT 1/4"2270-02546BOLT 3/8 X 3 UNC GR 5 PLATED4250-02747LOCKNUT 1/2 UNC PLATED8270-00748BOLT 1/2 X 2.5 UNC GR 5 PLATED2250-05249BOLT 1/2 X 3.5 UNC GR 5 PLATED2250-05050BOLT 1/2 X 1.75 UNC GR 5 PLATED4250-06051WASHER 1/2 PLATED ASME WIDE4256-01152LOCKNUT 5/8 UNC PLATED14270-00453WASHER 5/8 PLATED ASME WIDE8256-00654Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:10250-08855Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:4250-08856BOLT 3/4 X 4 UNC GR 5 PLATED4250-11157LOCKNUT 3/4 UNC PLATED4270-00158MLG Bushing 1.75 x 1.25 x 1.5 lg4365-00459Insert, 1/2", .063-.200 Wall8257-04560SFT CONE 395-10-23-301341-042561SFT CONE 395-10-25-551341-623562SFT CONE 395-10-25-453341-623663


FX742-CENTER SECTION

28

27

21

20

20

18

1615

14

10

9

1211 4

18

5

6

16

1721

19

26

1415

13

24

23

1

22

7

20

253

8

9

10

27 2

8

28

29

30


FX742-INNER LEFT WING

DescriptionQtyPart No.Ref.FX742 Left Inner Wing Inner Section1C742-1501Gearbox: B&P: R=1:1: 1-3/4" Z=201330-5572Gear box: 1:1.111 ratio: BP: Y31251110041330-8673Wing Stand1C742-1644Wing Adjustment Assembly1C742-1385FX742 Wheel Standard Adj Mount1C742-1376Heyco Dome Plug Part #24551280-1517Washer: 3/8":16256-0178Lockwasher: 3/8":16255-0139Bolt: 3/8 x 3/4 UNC: GR5: plated:16250-01710Bolt: 1/2 x 1-1/4 UNC: GR5:4250-06111Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:4256-01112Locknut: 1/2 UNC: plated4270-00713Washer: 1": 1-1/16" ID x 2" OD SAE2256-00114Cotter pin: 3/16 x 1-1/2:1271-00515Nut: 1-1/4": unc:2257-05316Lock washer: 1-1/41255-02017Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01518Insert: 1/2-13 UNC: .200-.350 Grip Range8257-04419Locknut: 5/8 UNC: plated41270-00420Washer: 5/8":32256-00621Lockwasher: 5/84255-00522Bolt: 5/8 x 1-1/2 UNC: GR5: plated:4250-09523Bolt: 5/8 x 2-1/4 UNC: GR 5: plated33250-08924Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:6250-08825Bolt: 5/8 x 2-3/4 UNC: GR5: plated2250-087126SFT:CE shield: 3950025452341-623627SFT counter cone2341-042528FX-742 Front Wing Shim1C742-21829FX-742 Rear Wing Shim1C742-21930


FX742-INNER LEFT WING

4

16626

28

27

20

10

2

28 8 9 10

1415

18

5

253

19

2027

89

14

20

15

1817

16

21

11

12

13

7

2421

22

23

1

30

29


FX742-INNER RIGHT WING

DescriptionQtyPart No.Ref.FX742 right Inner Wing Inner Section1C742-1551Gearbox: B&P: R=1:1: 1-3/4" Z=201330-5572Gear box: 1:1.111 ratio: BP Y31251110051330-8683Wing Stand1C742-1644Wing Adjustment Assembly1C742-1385FX742 Wheel Standard Adj Mount1C742-1376Heyco Dome Plug Part #24551280-1517Washer: 3/8":16256-0178Lockwasher: 3/8":16255-0139Bolt: 3/8 x 3/4 UNC: GR5: plated:16250-01710Bolt: 1/2 x 1-1/4 UNC: GR5:4250-06111Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:4256-01112Locknut: 1/2 UNC: plated4270-00713Washer: 1": 1-1/16" ID x 2" OD SAE2256-00114Cotter pin: 3/16 x 1-1/2:1271-00515Nut: 1-1/4": unc:2257-05316Lock washer: 1-1/41255-02017Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01518Insert: 1/2-13 UNC: .200-.350 Grip Range8257-04419Locknut: 5/8 UNC: plated41270-00420Washer: 5/8":32256-00621Lockwasher: 5/84255-00522Bolt: 5/8 x 1-1/2 UNC: GR5: plated:4250-09523Bolt: 5/8 x 2-1/4 UNC: GR 5: plated33250-08924Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:6250-08825Bolt: 5/8 x 2-3/4 UNC: GR5: plated2250-087126SFT:CE shield: 3950025452341-623627SFT counter cone2341-042528FX-742 Front Wing Shim1C742-21829FX-742 Rear Wing Shim1C742-21930


FX742-INNER RIGHT WING

26 26

26

27

27

27

24

13

11

12

25

25

24

24

24

8

7

2914 16153

3016 15 14

1024

27

416 28 2015149

26

23

2422

20

21

2

25

24

8

16

517

18

19

21

7

32

31

24

23 33


FX742-OUTER WINGS - LEFT

DescriptionQtyPart No.Ref.FX742 Left Outer Wing1C742-1521FX742 Left Inner Wing Outer Section1C742-1512Gear Box: 1:1.111: BP: Y31251110061330-8693Gear box: 1:1.111 ratio: BP Y31251110051330-8684Skid: Wing Rear1C742-2135Skid shoe front: left:1C502-1376Heyco Dome Plug Part #24552280-1517FX742 Outside Wing Hinge Pin2C742-1928Plate Outer Wing Lift Link2C742-1699FX742 Outer Wing Lift Link1C742-16810FX742 Outside Wing Lift Pin1C742-18111Wing Lift Pin1C742-18412Wing Lift Pin1C742-18313Bolt: 3/8 x 3/4 UNC: GR5: plated:12250-01714Lockwasher: 3/8":12255-01315Washer: 3/8":12256-01716Plow bolt: 1/2 x 1-1/2 UNC:6250-20117Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:6256-01118Locknut: 1/2 UNC: plated6270-00719Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:12250-08820Locknut: 5/8 UNC: plated12270-00421Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01522Cotter pin: 3/16 x 1-1/2:2271-00523Washer: 1": 1-1/16" ID x 2" OD SAE7256-00124Roll Pin: 3/8" x 1-3/4"4262-01125Roll pin: 3/8 x 2:6262-00626Machine bushing:1-1/4 ID x 1-7/8 OD x 10 ga:plated4256-07127SFT:CE shield: 3950025451341-623628CE shield: 5026 & S150 M2 & FX7421341-623529FX-742 Flexible Rubber shield1C742-21630Insert: 1/2-13 UNC: .200-.350 Grip Range5257-04431Insert: 1/2-13: .063- .200 Grip Range7257-04532Clevis pin: 1 x 2-29/641302-01433


FX742-OUTER WINGS - LEFT

2627

26

24

26

27

2726

26

24

2627

25

24

2425

24

2524

23

24

21

14

15

16

16

13

12

11

10

8

8

7

428

9

14

15

1621

20

75

18

6 19

17

2

29

20

3

30

15

14 22

31

32

23

33


FX742-OUTER WINGS - RIGHT

DescriptionQtyPart No.Ref.FX742 Right Outer Wing1C742-1571FX742 Right Inner Wing Outer Section1C742-1562Gear Box: 1:1.111: BP: Y31251110061330-8693Gear box: 1:1.111 ratio: BP: Y31251110041330-8674Skid: Wing Rear1C742-2135Skid shoe front: right:1C502-1366Heyco Dome Plug Part #24552280-1517FX742 Outside Wing Hinge Pin2C742-1928Plate Outer Wing Lift Link2C742-1699FX742 Outer Wing Lift Link1C742-16810FX742 Outside Wing Lift Pin1C742-18111Wing Lift Pin1C742-18412Wing Lift Pin1C742-18313Bolt: 3/8 x 3/4 UNC: GR5: plated:12250-01714Lockwasher: 3/8":12255-01315Washer: 3/8":12256-01716Plow bolt: 1/2 x 1-1/2 UNC:6250-20117Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:6256-01118Locknut: 1/2 UNC: plated6270-00719Bolt: 5/8" x 2-1/2": UNC: Gd 5: plated:12250-08820Locknut: 5/8 UNC: plated12270-00421Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01522Cotter pin: 3/16 x 1-1/2:2271-00523Washer: 1": 1-1/16" ID x 2" OD SAE7256-00124Roll Pin: 3/8" x 1-3/4"4262-01125Roll pin: 3/8 x 2:6262-00626Machine bushing:1-1/4 ID x 1-7/8 OD x 10 ga:plated4256-07127SFT:CE shield: 3950025451341-623628CE shield: 5026 & S150 M2 & FX7421341-623529FX-742 Flexible Rubber shield1C742-21630Insert: 1/2-13 UNC: .200-.350 Grip Range5257-04431Insert: 1/2-13: .063- .200 Grip Range7257-04532Clevis pin: 1 x 2-29/641302-01433


FX742-OUTER WINGS - RIGHT

24

8

46

45

2

4

48

47

1734

39

28

29

3031

40

40

41

119

18

10 21

39

35

34

177 476

1

3

3234

33

42

41

42

4344

35

47

49

39

1634

35

39

48

16

3438

37

13

12 15

23

22

24

35

34

34

36

1419

22

20

27

26

25

44

43

5

39

48

39

33


FX742-FRONT HITCH

DescriptionQtyPart No.Ref.FX742 Front Hitch1C742-1101Parallel Hitch Tension Link Left1C742-1122Parallel Hitch Tension Link Right1C742-1133Solid Tongue Parallel Lift1C742-1064FX742 Center Left Tension Link1C742-2065FX742 Center Right Tension Link1C742-2056PTO Stand1C000-1327FX-742 Jack Adjustment Assembly For C742-860 Jack Assembly1C742-1078FX-742 Jack Assembly with Reinforced Foot1C742-8609Jack Handle: Jack 232-8501232-85510Pull pin assembly: 3/4":1232-75411Hyd Hose Holder Left Leg1C742-16712Hyd Hose Holder right Leg1C742-16613Hyd. Hose Holder Top Plate1C742-16514Plastic Manual Storage Cannister1280-20115FX742 Center Tension Link Pin4C742-14516FX742 Clevis Pin3C742-14317Quick pin: 3/8 x 2 1/4: useable length Do Cap # 441302-03018Harness Storage: Cole Hersee #117501S000-08219Hose and tube clamp: 1/2"2C000-00120Plastic Grab Handle: 1-5/16" Red1280-15521Bolt: 1/4 x 1 UNC: GR5: Plated:4250-00222Washer: 1/4":2256-01823Locknut: 1/4 UNC: plated4270-02524Bolt: 3/8 x 1-3/4 UNC: GR5: pl;ated:2250-02325Washer: 3/8":2256-01726Locknut: 3/8 UNC: plated2270-01727Bolt: 3/4 x 1-1/2 UNC: GR5: plated:1250-11628Lockwasher: 3/4":1255-00329Safety Chain Washer: 2-1/2" x 13/16" x 1/2" Plated1C520-11830Safety Chain: 3/8" x 59" 20:100 Lb Rating1S000-01231Compression spring: .08" wire: .72" OD: 1.5" lg.1229-01032Cotter pin: 1/8 x 1: plated2271-00833Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:12256-01134Bolt: 1/2 x 1-3/4 UNC: GR5: plated:6250-06035Bolt: 1/2 x 1-1/4 UNC: GR5:2250-06136Bolt: 1/2 x 1 UNC: GR5: plated:2250-06337Lockwasher: 1/22255-00938Locknut: 1/2 UNC: plated12270-00739Bolt: 3/4 x 2 UNC: GR5: plated4250-11540Washer: 3/4ID X 1.5 OD4256-00341Locknut: 3/4 UNC: plated4270-00142Machine bushing:1-1/4 ID x 1-7/8 OD x 10 ga:plated9256-07143Roll pin: 3/8 x 2:3262-00644Washer: 1":(1-3/32ID x 2-1/2" OD:x .165T: 10 Ga.2256-00245Locknut: 1": unc:2270-00246MLG Bushing 1.75 x 1.25 x 1.5 lg6365-00447MLG Bushing 1.25 x 1 x .75 lg4365-00148MLG Bushing 1.25 x 1 x 1.1875 lg2365-00249


FX742-FRONT HITCH

41

25

16

14

9

14

19

4025

2423

15

35

8

31

2425

35

31

24 25 1640

4030

29

29

30

37

3839

34

29 30

23

24

33

20

24

21

3613

12

2324

25

1640403029

32

23

32

9

2535

22

24

17

172535

2422

28

31

8

31

27

26

18

1819

10

11

2

3

4

5

7

6

1

41

4225

24

23


FX742-CENTER WHEEL STANDARD

DescriptionQtyPart No.Ref.FX742 Center wheel Standard1C742-1391FX742 LEFT ROW CROP WHEEL EXT1C742-1322FX742 RIGHT ROW CROP WHEEL EXT1C742-1333FX742 LEFT 3 METER WHEEL EXT1C742-1344FX742 RIGHT 3 METER WHEEL EXT1C742-1355FX742 CENTER SUSPENSION ASSEMBLY1C742-1216FX742 CYLINDER CENTER FLOATING LUG1C742-1317FX742 CENTER WHEEL STANDARD PLATE4C742-1258FX742 CENTER WHEEL ARM LEFT (Shown)2C742-1249FX742 CENTER WHEEL ARM RIGHT2C742-244FX742 CENTER LEFT TENSION LINK1C742-20610FX742 CENTER RIGHT TENSION LINK1C742-20511FX-742 Tension Link Trunion2C742-18912Trunion Base Plate2C742-19713CENTER WHEEL STD SUPPORT PLATE2C742-13614FX742 CENTER WHEEL STANDARD PIN2C742-14015FX742 CENTER SUSPENSION PIN3C742-14616SPINDLE S618, 2 X 16.875, 1 HOLE4208-02917LIGHT BRACKET, ADV. LIGHTING STYLE2S000-10118SAFETY LIGHTS FX742, WITH HARNESS1S000-09219RUBBER SUSPENSION PUCK 70 DUROMETER3233-05320BOLT 1/2 X 4 UNC GR 5 PLATED3250-04821BOLT 1/2 X 6 UNC GR 5 PLATED4250-045322BOLT 1/2 X 1.75 UNC GR 5 PLATED13250-06023WASHER 1/2 PLATED ASME WIDE23256-01124LOCKNUT 1/2 UNC PLATED20270-00725BOLT 3/8 X 1.25 UNC GR 5 PLATED4250-01926WASHER 3/8 PLATED ASME WIDE4256-01727LOCKNUT 3/8 UNC PLATED4270-01728ROLL PIN 3/8 X 2 PLATED5262-00629MACHINE BUSHING 1-1/4 I.D. X 1-7/8 O.D. X 10GA PLATED5256-07130BOLT 1 X 2.75 UNC GR 5 PLATED20250-12631BOLT 1 X 3.5 UNC GR 5 PLATED4250-12432BOLT 3/4 X 5 UNC GR 5 PLATED1250-11033LOCKNUT 3/4 UNC PLATED1270-00134LOCKNUT 1 UNC PLATED24270-00235NUT 1-1/4 UNC GR 2 PLATED4257-05336CLEVIS PIN, 1" X 2-7/8" U.L.1302-01537WASHER 1 PLATED SAE1256-00138COTTER PIN 3/16 X 1-1/2 PLATED1271-00539MLG BUSHING, 1.75 X 1.25 X .75 LONG6365-00340Grease nipple, self-tap, 1/4-284273-00641Cover Plate4C742-19042


FX742-CENTER WHEEL STANDARD

25

24

26

235

29

23

11

16

25

24

9

25

24

2

13

1230

14

1718

24

27

19

4

2025

3

24

28

6

26

29

3110

7

8

2524

15

15

21

19

22

29

7

26

2524

71

26

29

20

25

24

284

3

6


FX742-WHEEL STANDARDS - LEFT

DescriptionQtyPart No.Ref.FX742 Outer Left Wing Wheel Std1C742-1281FX742 Left Inside Wing Wheel Standard1C742-1262FX742 Wheel Wing Arm2C742-12335 x 5 Mount Plate2C742-1224FX-742 Turnbuckle1C742-2095618 Spindle: 16-7/8" x 2": 2 Bolt Holes2208-0296FX742 Wing Wheel Standard Pin3C742-1417FX742 Inside Wing Wheel Standard Pin1C742-1428FX742 Castor Parallel Link Arm Pin1C742-1449Wing Tension Link Pin1C742-18710Mechanical Link Spacer2C742-19611FX742 Wing Suspension Assembly1C742-13012Rubber Puck: 70 Durometer: 3-1/2" OD x 2-3/8" lg2233-05313Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01514Roll pin: 3/8 x 2:2262-00615Turnbuckle Assy 10-1/8 min: 12-5/8 max1232-02116Washer: 1": 1-1/16" ID x 2" OD SAE1256-00117Cotter pin: 3/16 x 1-1/2:1271-00518Bolt: 1 x 2-3/4 UNC: GR5: plated8250-12619Locknut: 1": unc:8270-00220FX742 Wing Tension Link1C742-20721Bolt: 3/4 x 4-1/2 UNC: GR5: plated:2250-14422Locknut: 3/4 UNC: plated2270-00123Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:11256-01124Locknut: 1/2 UNC: plated9270-00725Bolt: 1/2 x 1-3/4 UNC: GR5: plated:5250-06026Bolt: 1/2 x 4 UNC: GR5: plated:2250-04827Bolt: 1/2 x 5 UNC: GR5:plated:2250-04628MLG Bushing 1.75 x 1.25 x .75 lg8365-00329MLG Bushing 1.25 x 1 x .75 lg2365-00130Tension bushing: 1-1/4" x 1-1/2" x 1" lg.1362-02231


FX742-WHEEL STANDARDS - LEFT

25 24

26

7

7

29

29

6

3

19

4

28

24

6

2428

27

3

194

25

2022

2520

14

23

11

7

29

16

22

15

29

11

26

1

2524

13

24

12

25

25

24

298

21 5 10

2615

312

1725

2318

30

24 9 26

24


FX742-WHEEL STANDARDS - RIGHT

DescriptionQtyPart No.Ref.FX742 Outer Right Wing Wheel Std.1C742-1291FX742 Right Inner Wing Wheel Std1C742-1272FX742 Wheel Wing Arm2C742-12335 x 5 Mount Plate2C742-1224FX-742 Turnbuckle1C742-2095618 Spindle: 16-7/8" x 2": 2 Bolt Holes2208-0296FX742 Wing Wheel Standard Pin3C742-1417FX742 Inside Wing Wheel Standard Pin1C742-1428FX742 Castor Parallel Link Arm Pin1C742-1449Wing Tension Link Pin1C742-18710Mechanical Link Spacer2C742-19611FX742 Wing Suspension Assembly1C742-13012Rubber Puck: 70 Durometer: 3-1/2" OD x 2-3/8" lg2233-05313Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate1302-01514Roll pin: 3/8 x 2:2262-00615Turnbuckle Assy 10-1/8 min: 12-5/8 max1232-02116Washer: 1": 1-1/16" ID x 2" OD SAE1256-00117Cotter pin: 3/16 x 1-1/2:1271-00518Bolt: 1 x 2-3/4 UNC: GR5: plated8250-12619Locknut: 1": unc:8270-00220FX742 Wing Tension Link1C742-20721Bolt: 3/4 x 4-1/2 UNC: GR5: plated:2250-14422Locknut: 3/4 UNC: plated2270-00123Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:11256-01124Locknut: 1/2 UNC: plated9270-00725Bolt: 1/2 x 1-3/4 UNC: GR5: plated:5250-06026Bolt: 1/2 x 4 UNC: GR5: plated:2250-04827Bolt: 1/2 x 5 UNC: GR5:plated:2250-04628MLG Bushing 1.75 x 1.25 x .75 lg8365-00329MLG Bushing 1.25 x 1 x .75 lg2365-00130Tension bushing: 1-1/4" x 1-1/2" x 1" lg.1362-02231


FX742-WHEEL STANDARDS - RIGHT

15

14

20

20

1918

17

11

2524

23

1918

1711

9

10

12

2120 1

527

26

7

7

6

24

22

16

4

15

14

13

19 1817

11

825

3

20

20

2

2


FX742-FRONT CASTOR WHEELS

DescriptionQtyPart No.Ref.FX742 Castor Link Assembly1C742-1171FX742 Parallel Link Arm2C742-1162FX742 Parallel Link Cross Beam1C742-1183FX742 Castor Mount1C742-1194FX742 Left Castor1C742-1145FX742 Right Castor1C742-1156Spindle: S618: complete with nut/washer1208-0267Wheel standard mount plate: wing:2C320-1288FX742 Wing Tension Link1C742-2079Wing Tension Link Pin1C742-18710FX742 Castor Parallel Link Arm Pin9C742-14411Roll pin: 3/8 x 2:2262-00612Roll pin: 3/8 x 3:1262-00413Machine bushing: 2 x 3 x 10 ga.2256-05314Tension bushing: 2" ID x 2-1/4" OD x 1" long2362-01915Grease nipple: self-tap: 1/4-282273-00616Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:9256-01117Lockwasher: 1/29255-00918Bolt: 1/2 x 1 UNC: GR5: plated:9250-06319MLG Bushing 1.25 x 1 x .75 lg18365-00120Tension bushing: 1-1/4" x 1-1/2" x 1" lg.1362-02221Bolt: 3/4 x 6-1/2 UNC: GR5: plated:4250-10622Bolt: 3/4 x 4-1/2 UNC: GR5: plated:2250-14423Washer: 3/4ID X 1.5 OD6256-00324Locknut: 3/4 UNC: plated6270-00125Bolt: 1/2 x 3-1/2 UNC: GR5:1250-05026Locknut: 1/2 UNC: plated1270-00727


FX742-FRONT CASTOR WHEELS

23

45

6

78

10

9

1

11

12

13

14

1516

17


FX742-HUB & TIRE

DescriptionQtyPart No.Ref.Hub, H618 complete, includes ref #2-121206-0031Seal1207-0182Bearing1207-0133Race1207-0144Grease nipple: 1/8 NPT: 45 deg1273-0025Race1207-0166Bearing1207-0157Washer, 1"1209-0108Castle nut, 1"-14 UNS1209-0119Cotter pin, 3/16"1271-00510Dust cap1207-01711Wheel Stud 9/16"6207-04812Wheel Nut 9/16" UNF6207-06513Wheel, 15 x 8 x 6 bolt, 4000 lb.1201-02014Valve Stem, Tubeless1211-00215Tire, 11L x 15, 12 ply.1210-14916Tire & Wheel, FARM HWY 11L15x12 ply on 15x8x6 HP Wheel4000LB Cap1210-51017


FX742-HUB & TIRE

7

1 2

9

3

6

1110

5

4

4

5

6

8

7

7

8

7

8

1

1

1

1

1

1

DescriptionQtyPart No.Ref.Blade Carrier, 6.5 Foot, 7 Gauge, Complete7C000-1441Brace Pan 6.5 Foot28586-10682Pan, 6.5 Foot , 7 Gauge7520-13083Blade Bolt, Pentagon Shoulder, 1/2"14251-0184Bushing, Pentagon Style14251-0205Locknut, 1-1/8 UNF Gr 814257-0036Blade, 1/2 X 4 X 28, Updraft, CW (Super Suction)8401-0327Blade, 1/2 X 4 X 28, Updraft, CCW (Super Suction)6401-0288Bevel Washer7331-8809Slotted Nut7331-87910Cotter Pin7331-87811


FX742-BLADE CARRIERS

1

1

3

10

45

6

7

8

9

10

10

10

11

11

11

11

2

12

101

10

12

10

11

10 111

12

10121

10

12

10121

10

12

10 121

10

DescriptionQtyPart No.Ref.Fixed Knife Bar, 6.5 Foot7C000-1461Blade Bolt, Shredder14251-0162Sleeve, 1.125 I.D.14C000-2013Lockwasher, 1-1/8"14255-0214Castle Nut14257-1075Cotter Pin, 1/4 x 2-1/2"14271-0116Bevel Washer7331-8807Slotted Nut7331-8798Cotter Pin7331-8789Blade, 1/2 X 4 X 28, Flat Double Edge14401-02410Blade, 1/2 X 4 X 28, Updraft, CCW (Super Suction)6401-02811Blade, 1/2 X 4 X 28, Updraft, CW (Super Suction)8401-03212


FX742-FIXED BLADE SHREDDING, UPDRAFT BLADES

19

20

2019

21

21

1921

19

20

19

22

20

19

2219

22

20

19

20

23

19 2119

20

19

20

19

20

19

22

20

23

2219201921

1922

19

20

19

20

19

19

20

19 20

1920

24

24

20

22 23

21

19

20

21

19 20

23

19

21

19 20

19

20

201922

21

19

21

19

20

19

22

19

2019

201920

11

11

14

18

12

9

3

16

17

1

2

15

13

8

10

4

21

2226

6

19

19

20

25

20 5

7


FX742-FIXED KNIFE SHROUDING

DescriptionQtyPart No.Ref.FX742 CENTER FRONT LEFT SHROUD1C742-2241FX742 CENTER FRONT RIGHT SHROUD1C742-2252FX742 OUTER LEFT WING FRONT SHROUD1C742-2323FX742 RIGHT OUTER WING FRONT SHROUD1C742-2334FX742 OUTER LEFT WING REAR SHROUD1C742-2405FX742 OUTER RIGHT WING REAR SHROUD1C742-2426FX742 LEFT OUTER WING SHROUD1C742-2347FX742 OUTER RIGHT WING SHROUD1C742-2358FX742 LEFT INNER WING OUTER SECTION1C742-2309FX742 RIGHT INNER WING OUTER SECTION SHROUD1C742-23110SHROUD SPACER2C742-23811FX742 LEFT INNER WING INNER SECTION SHROUD1C742-22812FX742 RIGHT INNER WING INNER SECTION SHROUD1C742-22913FX742 CENTER LEFT REAR SHROUD1C742-22214FX742 CENTER RIGHT REAR SHROUD1C742-22315FX742 CENTER SECTION LEFT SHROUD1C742-22616FX742 CENTER SECTION RIGHT SHROUD1C742-22717FX742 CENTER SHROUD1C742-22118WASHER 1/2 PLATED ASME WIDE92256-01119LOCKNUT 1/2 UNC PLATED92270-00720BOLT 1/2 X 1-1/4 UNC GR 5 PLATED62250-06121BOLT 1/2 X 1-1/2 UNC GR 5 PLATED16250-05922BOLT 1/2 X 1-3/4 UNC GR 5 PLATED8250-06023BOLT 1/2 X 4 UNC GR 5 PLATED6250-04824FX742 OUTER LEFT WING REAR SHROUD1C742-24125FX742 OUTER RIGHT WING REAR SHROUD1C742-24326


FX742-FIXED KNIFE SHROUDING

112

17

3

10

9

3

3

8

2

3

3

4

5

3


FX742-FIXED KNIFE MOUNTS OVERHEAD

DescriptionQtyPart No.Ref.Blade: Fixed:14401-2061FX742 Center Fixed Knife Mount1C742-2712FX742 Fixed Knife Mount6C742-2733FX742 Front Left Wing Fixed Knife1C742-2784FX742 Front Left Wing Fixed Knife1C742-2805FX742 Left Outside Wing Fixed Knife1C742-2767FX742 Center Right Fixed Knife1C742-2728FX742 Front Right Wing Fixed Knife1C742-2799FX742 Front Right Wing Fixed Knife1C742-28110FX742 Right Outside Wing Fixed Knife1C742-27712


FX742-FIXED KNIFE MOUNTS OVERHEAD

14

171

1

722

20

22

21

15

3

16

1

3

1

3

1

1

1

18

19

9

172022

17

1

12

20

81413

22

10

22

1

1

18

1920

14

1

22

417

1317

1

16

5

15

11615

22 20

21

22

20

2

17

3

3

1

13

3


FX742-FIXED KNIFE MOUNTS

DescriptionQtyPart No.Ref.Blade: Fixed:14401-2061FX742 Center Fixed Knife Mount1C742-2712FX742 Fixed Knife Mount6C742-2733FX742 Front Left Wing Fixed Knife1C742-2784FX742 Front Left Wing Fixed Knife1C742-2805FX742 Left Outside Wing Fixed Knife1C742-2767FX742 Center Right Fixed Knife1C742-2728FX742 Front Right Wing Fixed Knife1C742-2799FX742 Front Right Wing Fixed Knife1C742-28110FX742 Right Outside Wing Fixed Knife1C742-27712Locknut: steel: 3/4" UNF: Stover:14270-001113Locknut: steel: 1/2" UNF: plated Stover type14270-00814Bolt: 3/4 x 2-1/2 UNF: GR5:14250-114115Bolt: 1/2 x 2 UNF. GR5:14250-057116Bolt: 1/2 x 5 UNC: GR5:plated:14250-04617Bolt: 1/2 x 1-1/2 UNC: GR5: plated:16250-05918Lockwasher: 1/216255-00919Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:14256-01120Bolt: 1/2 x 1-3/4 UNC: GR5: plated:10250-06021Locknut: 1/2 UNC: plated24270-00722


FX742-FIXED KNIFE MOUNTS

6

1

711

10

6

29

87

987

98

7

11 7

10

3

1

1

5

4

4

1

1

4

4

5

1

1 32

1

5

4

4

1

1

4

4

5

1

2


FX742-CHAIN GUARDS

DescriptionQtyPart No.Ref.Chain Curtain 38"10C742-5011Chain Rod, 1/4 x 41" Cut Length106251-013Chain Curtain 22-7/16"2C742-5052Chain Rod, 1/4" x 25-7/16" long, 20-5/16" UL bent26251-010Chain Curtain 23-3/4"2C742-5043Chain Rod, 1/4" x 27-13/16" long, 22-11/16" UL bent26251-011Chain Curtain 37-17/32"8C742-5024Chain Rod, 1/4" x 39.5" Cut Length86251-014Chain Curtain 53"4C742-5035Chain Rod, 1/4" x 55-1/2" long, 51-1/2" UL bent46251-001Chain, 5 links774225-1076Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:104256-0117Lockwasher: 1/248255-0098Bolt: 1/2 x 1-3/4 UNC: GR5: plated:48250-0609Bolt: 1/2 x 4-1/2 UNC: GR5: plated:56250-04710Locknut: 1/2 UNC: plated56270-00711


FX742-CHAIN GUARDS

19

18

13

320

9

15

18 17 1615

19 18

20

20

18

19

12

12

14

13

11

11

12

12

11

11

13

12

13

11

11

12

1211

11

13

12

7

6

5

1

2

3

4

12 14

8

6

5

10

2

3

9

15

12

161718

18

17

16


FX742-FULL BELTING

DescriptionQtyPart No.Ref.FX742 Center Section Belting1C742-5511FX742 Left Inside Wing Belting2C742-5522FX742 Inside Left Wing Belting2C742-5533FX742 Left Outside Wing Belting1C742-5544FX742 Right Inside Wing Belting2C742-5555FX742 Inside Right Wing Belting2C742-5566FX742 Right Outside Wing Belting1C742-5577FX742 Rear Left Wing Belting1C742-5598Fx742 Rear Right Wing Belting1C742-5609FX742 Center Section Belting Rear1C742-55810FX742 Belting Retention Bar8C742-57211FX742 Belting Retention Bar10C742-57112FX742 Belting Retention Bar4C742-57313FX742 Belting Retention Bar2C742-57414FX742 Belting Retention Bar2C742-57515Bolt: 1/2 x 1-3/4 UNC: GR5: plated:48250-06016Lockwasher: 1/248255-00917Washer: 1/2: AS type A: 9/16 IDx1-3/8 ODx.109:104256-01118Locknut: 1/2 UNC: plated56270-00719Bolt: 1/2 x 4-1/2 UNC: GR5: plated:56250-04720


FX742-FULL BELTING

20

19

20

19

20

10

10

11

11

7

7

7

9

4

4

4

1

3

1

4

4

4

1

1 1

1

2

2 7 8 9

6

8

9

7

5

1

218

2022

3

1

5

17

21

19

16

12

19

20

11

13

4

5

4

5

10

11

1421

20

22

15

87


FX742-FRONT BELTING WITH FULL CHAINS

DescriptionQtyPart No.Ref.Chain Curtain 38"10C742-5011Chain Rod, 1/4 x 41" Cut Length106251-013Chain Curtain 22-7/16"2C742-5052Chain Rod, 1/4" x 25-7/16" long, 20-5/16" UL bent26251-010Chain Curtain 23-3/4"2C742-5043Chain Rod, 1/4" x 27-13/16" long, 22-11/16" UL bent26251-011Chain Curtain 37-17/32"8C742-5024Chain Rod, 1/4" x 39.5" Cut Length86251-014Chain Curtain 53"4C742-5035Chain Rod, 1/4" x 55-1/2" long, 51-1/2" UL bent46251-001Chain, 5 links774225-1076Washer 1/2 Plated104256-0117Lockwasher 1/2 Plated48255-0098Bolt 1/2 X 1.75 UNC GR 5 Plated48250-0609Bolt, 1/2 X 4-1/2 UNC GR556250-04710Locknut 1/2 UNC Plated56270-00711FX742 Center Section Belting1C742-55112FX742 Left Inside Wing Belting1C742-55213FX742 Inside Left Wing Belting1C742-55314FX742 Left Outside Wing Belting1C742-55415FX742 Right Inside Wing Belting1C742-55516FX742 Inside Right Wing Belting1C742-55617FX742 Right Outside Wing Belting1C742-55718FX742 Belting retention Bar4C742-57219FX742 Belting retention Bar6C742-57120FX742 Belting retention Bar2C742-57321FX742 Belting retention Bar2C742-57422


FX742-FRONT BELTING WITH FULL CHAINS

17

3

1

2

4

5

6

7

9

9

9

9

9

4

5

14

1516

17

18

1920

21

23

22


FX742-PHASING CIRCUIT

DescriptionQtyPart No.Ref.Cylinder: Phasing: 4 x 12 Welded: Monarch : Ports in line1100-40751Cylinder: Phasing: 3.75 x 12: Welded: Monarch Ports 90 Deg.1100-36952Cylinder: Phasing: 3.5 x 12: Welded: Monarch: Ports 90 Deg.1100-36853HYD Hose 3/8"x383": 8FJICx8MORB: ORB Pioneer1111-3444Hyd Hose 3/8"x262": 8FJICx8MORB: ORB Pioneer1111-3455Hyd. Hose 3/8 x 259: 8 FJIC x 8 FJIC1111-2966Hyd. Hose 3/8 x 134: 8 FJIC x 8 FJIC1111-2957Elbow: 90: 3/4-16 ORB male x 3/4-16 JIC male6108-0439Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate6302-01514Washer: 1": 1-1/16" ID x 2" OD SAE6256-00115Cotter pin: 3/16 x 1-1/2:6271-00516Double Hose Clamp: Complete Assembly: 3/8" hose7124-01317Washer: 5/16: AS type A2256-02018Lockwasher: 5/16":2255-01519Bolt: 5/16 x 3-1/2 UNC: GR5: plated:2250-01420Bolt: 5/16 x 1-3/4 UNC: GR5: plated:3250-01221Depth Stop Kit: 6 piece:3/8":1/2":3/4":1":2":2 1/2"3101-05322Plastic wire tie: 8" long: blue: WT-87280-00923


FX742-PHASING CIRCUIT

10

1

1

2

2

3

4

4

4

45

5

6

6

7

8

9

7

10

9

8

11

11

12

11

11

12

12

12

12

13

13

13 1414

15

16

17

17

18

19

20

21

22

24

23

4

25

26

26


FX742-WING LIFT CIRCUIT

DescriptionQtyPart No.Ref.Cylinder: 4-1/2 x 36: Welded: 45WD36-175: Monarch:2100-4411Cylinder: 4-1/2' x 16: welded:45WD16-150: Monarch2100-4402FX-742 Hydraulic Block: c/w Fittings1127-0263Hyd Hose 3/8"x230": 8FJICx8MORB: ORB Pioneer2111-3464Hyd. Hose 3/8 x 85: 8 FJIC x 8 FJIC2111-3015Hyd. Hose 3/8 x 29-1/2: 8 FJIC x 8 FJIC2111-3006Hyd. Hose 3/8 x 108: 8 FJIC x 8 FJIC 90 Deg.1111-2997Hyd. Hose 3/8 x 119: 8 FJIC x 8 FJIC1111-3028Hyd. Hose 3/8 x 83: 8 FJIC x 8 FJIC 90 Deg.1111-3039Hyd. Hose 3/8 x 68: 8 FJIC x 8 FJIC 90 Deg.1111-29810Branch tee: adjustable: 3/4-16 JIC X ORB:4108-04011Elbow: 90: 3/4-16 ORB male x 3/4-16 JIC male5108-04312Elbow: 45: 3/4-16 ORB male x 3/4-16 JIC male3108-04413Adapter: #8 Male ORB to #8 Male JIC2108-02514Lockwasher: 3/8":3255-01315Bolt: 3/8 x 1 UNC: GR5:3250-01816Double Hose Clamp: Complete Assembly: 3/8" hose7124-01317Bolt: 5/16 x 1-3/4 UNC: GR5: plated:3250-01218Washer: 5/16: AS type A2256-02019Lockwasher: 5/16":2255-01520Bolt: 5/16 x 3-1/2 UNC: GR5: plated:2250-01421Clevis pin: 1 x 2-7/8" useable: Zinc Di-chromate4302-01522Washer: 1": 1-1/16" ID x 2" OD SAE4256-00123Cotter pin: 3/16 x 1-1/2:4271-00524Cable tie: 15" long: UV black: 120 lb. tensile6280-00825Restrictor: screw in: male ORB: 1/16" hole2C000-00626


FX742-WING LIFT CIRCUIT

1

4

2

3

25

18

17

27

26

DescriptionQtyPart No.Ref.Casing: 4-1/2 x 161101-4041Cyl. head: 4-1/2x161101-4052Piston: 4-1/2" x 16:1101-4063Rod: Cyl. 4-1/2" x 16:1101-4074Rod Clevis:1101-40817Set screw: 3/8' unc: knurled:1101-16318Piston Bolt: 1" x 3" uns:1101-40925Seal Kit: 41/2" x 161101-41726Washer: 2 x1.061101-41027Cylinder: 4-1/2' x 16: welded:45WD16-150: Monarch1100-440-


HYDRAULIC CYLINDER, 100-440

1

4

2

3

25

18

17

27

26

DescriptionQtyPart No.Ref.Casing: 4-1/2"x361101-4111Cyl. Head: 4-1/2"1101-4122Piston: 4-1/2" :1.751101-4133Rod: 4-1/2'x36:1101-4144Rod Clevis:1101-40817Set screw: 3/8' unc: knurled:1101-16318Piston Bolt: 1" x 3" uns:1101-40925Seal Kit: 4-1/2x361101-41626Washer: 2 x1.061101-41027Cylinder: 4-1/2 x 36: Welded: 45WD36-175: Monarch:1100-441-


HYDRAULIC CYLINDER, 100-441

1

4

2

3

25

18

17

26


HYDRAULIC CYLINDER, 100-3685, 100-3695, 100-4075

DescriptionQtyPart No.Ref.Casing: 3-1/2 "x 12": Phasing:1101-3041Casing: 3-3/4" x 12: phasing:1101-301Casing: 4 x 12: Phasing:1101-401Cyl. Head. 3-1/2"1101-3062Cyl. head: 3-3/4"1101-302Cyl. Head: 4"1101-402Piston : 3-1/2": with wear ring:1101-0843Piston: 3-3/4": Phasing:1101-308Piston: 4"1101-166Rod: Cyl. 1.25" dia: 3-1/2" Cylinder1101-3074Rod: Cyl. 1.38"dia: 3-3/4" & 4" Cylinders1101-403Rod Clevis:1101-24617Set screw: 3/8' unc: knurled:1101-16318Nut: Piston1101-02325Piston Nut: 4x481101-174Seal kit: 3-1/2:1101-06726Seal Kit: 3-3/4" x 12: Phasing:1101-310Seal Kit: 4"x 12"1101-415Cylinder: Phasing: 3.5 x 12: Welded: Monarch: Ports 90 Deg.1100-3685-Cylinder: Phasing: 3.75 x 12: Welded: Monarch Ports 90 Deg.1100-3695Cylinder: Phasing: 4 x 12 Welded: Monarch : Ports in line1100-4075


HYDRAULIC CYLINDER, 100-3685, 100-3695, 100-4075

1

2

10

3 4

43

5

5

6

6

7

8

9

9

10

11

11

12

12


FX742-DRIVELINE LAYOUT

DescriptionQtyPart No.Ref.U-Joint: BP: SFT10: 80cv: 1-3/4z20: c/w overrunning clutch:1340-10021U-Joint,BP, SFT6, FT clutch,1340-6512U-Joint,BP,SFT#10, 1-3/4z20, c/w Shear Yoke,2340-10013U-Joint, BP, SFT6, FT clutch,2340-6524U-Joint, BP, SFT9, FT clutch,2340-9005U-Joint, BP, SFT8, ft clutch,2340-8606Gear Box, Divider, FX742, 1.35 : 1 Ratio1330-9367Gear Box, 1.28:1 ratio, BP, Y31250780031330-8668Gear box, 1:1.111 ratio, BP, Y31251110042330-8679Gear box, 1:1.111 ratio, BP Y31251110052330-86810Gear Box, 1:1.111, BP, Y31251110062330-86911Gearbox, B&P, R=1:1, 1-3/4" Z=202330-55712


FX742-DRIVELINE LAYOUT

2 22

168

40

6251

97

98

6 5 12 18 17

9493

2627 32 42

65 66 67 66

6463

2834

28

40

28

99

211

1 21

98

61

95 96


DRIVELINE, 340-1002 - TRACTOR SHAFT

DescriptionQtyPart No.Ref.Yoke: CV S10: 1-3/4 z 20: 340-10021341-100181Cross Kit: S102341-100192Yoke: CV: Tube 4-lobe: S101341-100205CV Body: S10:1341-100216Roll Pin:1341-800748Outer cardan tube: 4-lobe: 340-10021341-1002212Flexible pin: 10mm X 55mm:1341-808716Yoke: Inner Tube: S10: 4-lobe1341-1000517Inner cardan Tube: 4-lobe:1341-1002418Overrunning clutch: S10: 1-3/4 z 20: 340-10021341-1002521Cross Kit: S10:1341-1000222Shield Support: SFT S9: outer1341-91526Ring:1341-8005027Screw:14341-6002028Inner Bell Ring:1341-1001632Washer:6341-8006934Shielding Chain (CE Shielding Only)2341-6002140Safety Bell:1341-1001742Ball collar Kit: 1-3/4"1341-1002651Yoke : Body : S101341-1002761Hub: 1-3/4 z 20:1341-1002862Repair Kit:1341-1002963Tapered pin & nut:1-3/4 shaft: #408000076R1341-80264Half Plate:2341-627365Disc:2341-1003066Disc:1341-1003167U-joint tractor half assy. CV: S10: 1-3/4 z 20: 340-10021341-1003293U-joint implement Half: s10: 1-3/4 z 20: 340-10021341-1003394Safety Shield kit: Tractor half: 340-10021341-1003595Safety Shield Kit: Implement Half: 340-10021341-1003696Safety Shield Kit complete: 340-10021341-1003497Grease nipple:2341-65398Grease fitting: M8x 1.25-90 deg.1341-818299U-Joint: BP: SFT10: 80cv: 1-3/4z20: c/w overrunning clutch:1340-1002-


DRIVELINE, 340-1002 - TRACTOR SHAFT

98

28

40

8 16

70

97

2

74

5 12 23 13 17

9493

25 26 29 30 32 25

51

71 72 73

61

73 75 76 77

40

28

1 21

1

21


DRIVELINE, 340-651 - CENTER

DescriptionQtyPart No.Ref.Yoke: #S6: 1-3/4z20:1341-600101Cross Kit:2341-600082Yoke: outer 4-lobe tube:1341-600725Flexible Pin: Can use 341-7021341-800078Outer cardan tube: 4-lobe:1341-6009612Inner cardan Tube: 4-lobe:1341-6009713Flexible pin:1341-61616Yoke: Inner 4 Lobe:1341-6000617Slip clutch: FT42: #S6: 1-3/4 z 20:1341-6006721Grease fitting:1341-808623Safety Bell: S6:2341-6004325Ring for Outer Bell:1341-8001026Screw:6341-6002028Outer Bell & Safety Tube: 340-6511341-6009029Inner Bell & Safety Tube: 340-6511341-6009130Ring for Inner Bell:1341-8001332Shielding Chain (CE Shielding Only)2341-6002140Tapered pin & nut:1-3/4 shaft: #408000076R1341-80251Tapered pin & nut:1-3/4 shaft: #408000076R1341-80261Bolt & Nut : 10mm X 55mm: Gr 8.8:8341-601470Flange Yoke: #S6:1341-6007071Bushing:1341-63072Lining:2341-624773Flange Hub: FT42: 1-3/4z20:1341-628074Thrust plate:1341-624875Spacer:1341-625176Spring: cone type: clutch1341-631377U-joint half Assy. 340-6511341-6009393U-joint Half Assy. c/w clutch: 1-3/4 z 20: 340-6511341-6009494Safety Shield kit Complete: 340-6511341-6009597Grease nipple:2341-65398U-Joint:BP: SFT6: FT clutch:1340-651-


DRIVELINE, 340-651 - CENTER

98

8

40

28

2

70 74

40

28

16

93

5 12 23 13 17

94

253230292625

51

71 72 73 73 75 76 77

97

1 21

1

1

61


DRIVELINE, 340-652

DescriptionQtyPart No.Ref.Yoke: #S6: 1-3/4z20:1341-600101Cross Kit:2341-600082Yoke: outer 4-lobe tube:1341-600725Flexible Pin: Can use 341-7021341-800078Outer cardan tube: 4-lobe:1341-6009612Inner cardan Tube: 4-lobe:1341-6009713Flexible pin:1341-61616Yoke: Inner 4 Lobe:1341-6000617Slip clutch: FT42: #S6: 1-3/4 z 20:1341-6006721Grease fitting:1341-808623Safety Bell: S6:2341-6004325Ring for Outer Bell:1341-8001026Screw:6341-6002028Outer Bell & Safety Tube: 340-6511341-6009029Inner Bell & Safety Tube: 340-6511341-6009130Ring for Inner Bell:1341-8001332Shielding Chain (CE Shielding Only)2341-6002140Tapered pin & nut:1-3/4 shaft: #408000076R1341-80251Tapered pin & nut:1-3/4 shaft: #408000076R1341-80261Bolt & Nut : 10mm X 55mm: Gr 8.8:8341-601470Flange Yoke: #S6:1341-6007071Bushing:1341-63072Lining:2341-624773Flange Hub: FT42: 1-3/4z20:1341-628074Thrust plate:1341-624875Spacer:1341-625176Spring: cone type: clutch1341-631877U-joint Half assy. 1-3/4 z 20: 340-6521341-6010093U-joint Half assy. c/w clutch: 1-3/4 z 20 : 340-6521341-6010194Safety Shield kit Complete: 340-6511341-6009597Grease nipple:2341-65398U-Joint: BP: SFT6: FT clutch:1340-652-


DRIVELINE, 340-652

94

2

8

4347

43

46

1 21

16

52

70

61

40

28

40

28

5 1223

13 17

25 26 29 44 30 32 25

93

78 77 76 74

51

75 74 73 71

97

1

21

98


DRIVELINE, 340-860 - OUTER WING

DescriptionQtyPart No.Ref.Slip Clutch: #8: 1-3/4 z 20:1341-801071Cross Kit: BP:S8:2341-800022Yoke: Outer: 4-lobe: SFT#8:1341-800755Flexible pin: 10mm X 55mm:1341-80878Outer Cardan Tube: 4-Lobe:1341-8010912Inner cardan Tube: 4-Lobe:1341-8011013Spring dowel:1341-64616Yoke: #8:1341-8011117Yoke: #8:1341-8011221Grease Fitting:4341-8011323Bell:2341-8001425Ring for Outer Bell:1341-8001026Screw:6341-6002028Inner bell & Safety Tube: 340-8601341-8011429Outer Bell & Safety Tube: 340-8601341-8011530Ring for Inner Bell:1341-8001332Shielding Chain (CE Shielding Only)2341-6002140Spring:2341-8011643Safety Tube: 340-8601341-8011744Plug:1341-8011846Plug:1341-8011947Tapered pin & nut:1-3/4 shaft: #408000076R1341-80251Key:12341-8012152Ball Collar kit:1341-8012761Bolt & Nut : 10mm X 55mm: Gr 8.8:8341-601470Flange Yoke: #8:1341-8012371Bushing:1341-63073Lining:2341-624774Flange Hub: FT42: 1-3/4z20:1341-628075Thrust plate:1341-624876Spacer:1341-625177Spring: cone type: clutch1341-631878U-joint Half c/w clutch: 1-3/4 z 20: 340-8601341-8012493U-joint half: 1-3/4 z 20: c/w QD yoke: 340-8601341-8012594Safety Shield Kit Complete: 340-8601341-8012697Grease nipple:2341-65398U-Joint: BP: SFT8: ft clutch:1340-860-


DRIVELINE, 340-860 - OUTER WING

98

1 21

1

21

8 16

40

28

2

97

40

28

51

93 94

25 26 29 30 32 25

5 12 13 17

71 72 73 74 73 75 73 76 73

61

77 78 7970


DRIVELINE, 340-900

DescriptionQtyPart No.Ref.Yoke SFT #9: 1-3/4 z 20:1341-9011Cross Kit: #9:2341-9022Yoke: #S9: 4-lobe:1341-9035Flexible pin: 10mm X 55mm:1341-80878Outer cardan Tube: 4-lobe: 340-9001341-90412Inner cardan tube: 4-lobe: 340-9001341-90513Flexible Pin:1341-8003916Yoke: S9: Tube 4-lobe: 340-9001341-90617Slip Clutch: S9: 340-9001341-90721Shield Bell:2341-91425Shield Support: SFT S9: outer1341-91526Screw:6341-6002028Outer Bell & Safety Tube: 340-9001341-90829Inner Bell & Safety Tube: 340-9001341-90930Shield Support: SFT S9: Inner1341-91632Shielding Chain (CE Shileding Only)2341-6002140Tapered pin & nut:1-3/4 shaft: #408000076R1341-80251Tapered pin & nut:1-3/4 shaft: #408000076R1341-80261SEE 341-8120: Bolt & Nut: M10x70 #8.88341-91770Flange Yoke: #8:1341-812771Bushing:1341-63072Lining:4341-624773Lining support plate:1341-812274Inner Plate: no set screw holes:1341-813875Flange Hub: 1-3/4 z 20:1341-91876Thrust plate:1341-624877Spacer:1341-812578Spring:1341-91979U-joint Half assy. 340-9001341-91193U-joint Half Assy. c/w Clutch: 340-9001341-91294Safety Shield Kit Compltet: 340-9001341-91397Grease nipple:2341-65398U-Joint: BP: SFT9: FT clutch:1340-900-


DRIVELINE, 340-900

1

2

8

40

28

72

73

74

1

98

16

5 12 13 17

9493

42 25 26 29 30 32 25 42

97

28

40

41

21

21

61


DRIVELINE, 340-1001

DescriptionQtyPart No.Ref.Shear Yoke complete: S10: 1-3/4 z 20: 340-10011341-100011Cross Kit: S10:2341-100022Yoke: Outer Tube: S10: 4-lobe:1341-100035Roll Pin:1341-100118Outer Cardan Tube: 4-lobe:1341-1000412Inner Cardan Tube: 4-lobe:1341-1000613Flexible pin: 10mm X 55mm:1341-808716Yoke: Inner Tube: S10: 4-lobe1341-1000517Yoke : 1-3/4 Z 20: S10:1341-1000721Shield Bell:2341-1001225Outer Bell Ring:1341-1001326Screw:8341-6002028Outer Bell & Safety tube: 340-10011341-1001429Inner Bell & Safety Tube: 340-10011341-1001530Inner Bell Ring:1341-1001632Shielding Chain (CE Shielding Only)2341-6002140Grease fitting:1341-808641Safety Bell:2341-1001742Tapered pin & nut:1-3/4 shaft: #408000076R1341-80261Tapered pin & nut:1-3/4 shaft: #408000076R1341-80272Grease nipple:2341-65373Shear pin & nut: 12MM x 65MM: 1-3/4"1341-75674U-joint Half: c/w Shear Yoke: 1-3/4 z 20:1341-1000993U-joint Half: 1-3/4z20: 340-10011341-1001094Safety Shield Kit Complete: 340-10011341-1000897Grease nipple:2341-65398U-Joint:BP:SFT#10: 1-3/4z20: c/w Shear Yoke:1340-1001-


DRIVELINE, 340-1001

5

4

3

2

1

6

17

8

9

718

19

10

11

12

1323

22

21

20

16

15

14

3

6


GEARBOX, 330-866 - CENTER

DescriptionQtyPart No.Ref.Bolt: 3/8 x 3/4 UNC: GR5: plated:6250-0171SEE 331-990: Washer:6331-80342Tapered Bearing & Race:2331-5643Oil seal:1331-90194Input Shaft: 1-3/4z20:1331-80355Snap ring:internal:.105" thick:2331-5526Gear Set: 1.28:1 ratio:1331-80497Bearing:1331-70128Pinion Shaft:1331-80399Tapered Roller Bearing:1331-711410Magnetic Plug:1331-804011Spring washer: 3125 & LF223 gearbox1331-88012Split pin:1331-87813Breather Plug: Vent: Dipstick1331-804114Cover:1331-804215Cap : 85x10mm1331-55916SEE 331-588: Shims:1331-98217SEE 331-812: Cotter Pin:1331-804818Castle Nut:1331-804319Housing: 3125:1331-804420Oil Seal:1331-804521Sealing Lid:1331-804622Castle nut:1331-87923Gear Box: 1.28:1 ratio: BP: Y31250780031330-866-


GEARBOX, 330-866 - CENTER

14

15

3

6

16

17

18

19

20

21

22

23

1

2

3

4

5

6

7

8

9

10

11

12

13


GEARBOX, 330-867 - INNER LEFT, OUTER RIGHT

DescriptionQtyPart No.Ref.Bolt: 3/8 x 3/4 UNC: GR5: plated:6250-0171SEE 331-990: Washer:6331-80342Tapered Bearing & Race:2331-5643Oil seal:1331-90194Input Shaft: 1-3/4z20:1331-80355Snap ring:internal:.105" thick:2331-5526Gear Set: 1:1.111 ratio:1331-80507Bearing:1331-70128Pinion Shaft:1331-80399Tapered Roller Bearing:1331-711410Magnetic Plug:1331-804011Spring washer: 3125 & LF223 gearbox1331-88012Split pin:1331-87813Breather Plug: Vent: Dipstick1331-804114Cover:1331-804215Cap : 85x10mm1331-55916SEE 331-588: Shims:1331-98217SEE 331-812: Cotter Pin:1331-804818Castle Nut:1331-804319Housing: 3125:1331-804420Oil Seal:1331-804521Sealing Lid:1331-804622Castle nut:1331-87923Gear box: 1:1.111 ratio: BP: Y31251110041330-867-


GEARBOX, 330-867 - INNER LEFT, OUTER RIGHT

5

3

4

2

1

13

12

11

10

8

9

19

18

17

6

23

20

21

22

6

16

7

14

15

3


GEARBOX, 330-868 - INNER RIGHT, OUTER LEFT

DescriptionQtyPart No.Ref.Bolt: 3/8 x 3/4 UNC: GR5: plated:6250-0171SEE 331-990: Washer:6331-80342Tapered Bearing & Race:2331-5643Oil seal:1331-90194Input Shaft: 1-3/4z20:1331-80355Snap ring:internal:.105" thick:2331-5526Gear Set: 1:1.111 ratio:1331-80507Bearing:1331-70128Pinion Shaft:1331-80399Tapered Roller Bearing:1331-711410Magnetic Plug:1331-804011Spring washer: 3125 & LF223 gearbox1331-88012Split pin:1331-87813Breather Plug: Vent: Dipstick1331-804114Cover:1331-804215Cap : 85x10mm1331-55916SEE 331-588: Shims:1331-98217SEE 331-812: Cotter Pin:1331-804818Castle Nut:1331-804319Housing: 3125:1331-804420Oil Seal:1331-804521Sealing Lid:1331-804622Castle nut:1331-87923Gear box: 1:1.111 ratio: BP Y31251110051330-868-


GEARBOX, 330-868 - INNER RIGHT, OUTER LEFT

14

15

3

6

417

18

19

20

21

22

23

1

2

3

4

5

6

7

8

9

10

11

12

13


GEARBOX, 330-869 - OUTER RIGHT & LEFT

DescriptionQtyPart No.Ref.Bolt: 3/8 x 3/4 UNC: GR5: plated:6250-0171SEE 331-990: Washer:6331-80342Tapered Bearing & Race:2331-5643Oil seal:2331-90194Input Shaft: 330-869/330-8701331-80515Snap ring:internal:.105" thick:2331-5526Gear Set: 1:1.111 ratio:1331-80507Bearing:1331-70128Pinion Shaft:1331-80399Tapered Roller Bearing:1331-711410Magnetic Plug:1331-804011Spring washer: 3125 & LF223 gearbox1331-88012Split pin:1331-87813Breather Plug: Vent: Dipstick1331-804114Cover:1331-804215SEE 331-588: Shims:1331-98217SEE 331-812: Cotter Pin:1331-804818Castle Nut:1331-804319Housing: 3125:1331-804420Oil Seal:1331-804521Sealing Lid:1331-804622Castle nut:1331-87923Gear Box: 1:1.111: BP: Y31251110061330-869-


GEARBOX, 330-869 - OUTER RIGHT & LEFT

1213

14

15

11

3

4

6

1

4

16

5

4

2

3

16

5

6

8

6

4

5

16

10

7

8

6

5

16

3

2

3


GEARBOX, 330-936 - DIVIDER BOX, CENTER

DescriptionQtyPart No.Ref.Gear Set: 1.35:1 ratio: 330-9361331-9961Pinion Shaft: 1-3/4 z20:2331-9932Oil Seal: 330-9364331-9993Snap ring:internal:.105" thick:4331-5524SEE 331-588: Shims:4331-9825Tapered Roller Bearing:4331-5756Housing:1331-9917Bearing: 32207JR:2331-9338Input shaft: 1-3/4 z 20:1331-99210Magnetic Plug:1331-98611Cover: 330-9361331-99412Breather Plug: Vent:1331-98813Bolt: 330-9366331-99714Washer: 330-9366331-99815Spacer:4331-99516


GEARBOX, 330-936 - DIVIDER BOX, CENTER

1

11

8

13

14

10

15

6

4

7

3

13

9

11

12

16

8

2

13

11

5


GEARBOX, 330-557 - INNER RIGHT & LEFT

DescriptionQtyPart No.Ref.Housing1331-5921Shaft, 1-3/4 z201331-5932Shaft, 1-3/4 z201331-5953Spacer1331-5964Cover1331-5815Snap Ring1331-5826Snap Ring1331-9637Snap Ring2331-5528Shim Kit1331-5879Shim Kit1331-58810Tapered Bearing & Race3331-56411Tapered Roller Bearing1331-57512Oil Seal3331-901913Breather Plug1331-57814Oil Plug2331-56115Gear Set1331-59416Complete Gearbox, BP #S2100100091330-557


GEARBOX, 330-557 - INNER RIGHT & LEFT

1

2

5

2

4

3

1

NOTE: The lights are to be mounted with the red and amber facing to the rear of the machine, withthe amber to the outside.

DescriptionQtyPart No.Ref.Light Bracket: Advanced Lighting Style2S000-1011Adv. Safety Light: FX742 mower w/ harness1S000-0922Bolt: 3/8 x 1-1/4 UNC: GR5: plated4250-0193Washer: 3/8":4256-0174Locknut: 3/8 UNC: plated4270-0175


FX742-TRANSPORT LIGHTS

NOTE: This safety chain is intended as an auxiliary attaching system per ASAE S338.3. The safetychain will help control the rotary cutter should it accidentally separate from the drawbar. Do NotUse the Safety Chain for Towing. Replace the entire chain if any link or end fitting is broken,

damaged or stretched.DescriptionQtyPart No.Ref.Safety Chain: 3/8" x 59" 20:100 Lb Rating1S000-0121


SAFETY CHAIN S000-012

100-3685....................................................38, 44100-3695....................................................38, 44100-4075....................................................38, 44100-440......................................................40, 41100-441......................................................40, 42101-023............................................................44101-053............................................................38101-067............................................................44101-084............................................................44101-163................................................41, 42, 44101-166............................................................44101-174............................................................44101-246............................................................44101-301............................................................44101-302............................................................44101-304............................................................44101-306............................................................44101-307............................................................44101-308............................................................44101-310............................................................44101-401............................................................44101-402............................................................44101-403............................................................44101-404............................................................41101-405............................................................41101-406............................................................41101-407............................................................41101-408......................................................41, 42101-409......................................................41, 42101-410......................................................41, 42101-411............................................................42101-412............................................................42101-413............................................................42101-414............................................................42101-415............................................................44101-416............................................................42101-417............................................................41108-025............................................................40108-040............................................................40108-043......................................................38, 40108-044............................................................40111-295.............................................................38111-296.............................................................38111-298.............................................................40111-299.............................................................40111-300.............................................................40111-301.............................................................40111-302.............................................................40111-303.............................................................40111-344.............................................................38111-345.............................................................38111-346.............................................................40124-013......................................................38, 40127-026............................................................40

201-020............................................................22206-003............................................................22207-013............................................................22207-014............................................................22207-015............................................................22207-016............................................................22207-017............................................................22207-018............................................................22207-048............................................................22207-065............................................................22208-026............................................................20208-029................................................14, 16, 18209-010............................................................22209-011............................................................22210-149............................................................22210-510............................................................22211-002............................................................22225-107......................................................32, 36229-010............................................................12232-021......................................................16, 18232-754............................................................12232-855............................................................12233-053................................................14, 16, 18250-002............................................................12250-0021............................................................2250-012......................................................38, 40250-014......................................................38, 40250-017....................2, 4, 6, 8, 10, 60, 62, 64, 66250-018............................................................40250-019......................................................14, 71250-023............................................................12250-027..............................................................2250-0453..........................................................14250-046................................................16, 18, 30250-047................................................32, 34, 36250-048..........................................14, 16, 18, 26250-050........................................................2, 20250-052..............................................................2250-0571..........................................................30250-059......................................................26, 30250-060........2, 12, 14, 16, 18, 26, 30, 32, 34, 36250-061..............................................4, 6, 12, 26250-063......................................................12, 20250-0871........................................................4, 6250-088............................................2, 4, 6, 8, 10250-089..........................................................4, 6250-095..........................................................4, 6250-106............................................................20250-110............................................................14250-111...............................................................2250-1141..........................................................30250-115............................................................12250-116............................................................12250-124............................................................14


PART INDEX

250-126................................................14, 16, 18250-144................................................16, 18, 20250-201........................................................8, 10251-008..............................................................2251-016............................................................24251-018............................................................23251-020............................................................23255-003............................................................12255-005..........................................................4, 6255-009..............................12, 20, 30, 32, 34, 36255-013......................................2, 4, 6, 8, 10, 40255-015..................................................2, 38, 40255-020..........................................................4, 6255-021............................................................24256-001..............2, 4, 6, 8, 10, 14, 16, 18, 38, 40256-002............................................................12256-003......................................................12, 20256-006......................................................2, 4, 6256-011......2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 26,

3 0 , 3 2 , 3 4 , 3 6256-017..........................2, 4, 6, 8, 10, 12, 14, 71256-018............................................................12256-020..................................................2, 38, 40256-053............................................................20256-071........................................2, 8, 10, 12, 14257-003............................................................23257-044................................................4, 6, 8, 10257-045....................................................2, 8, 10257-053....................................................4, 6, 14257-107............................................................24262-004............................................................20262-006......................2, 8, 10, 12, 14, 16, 18, 20262-011........................................................8, 10262-012..............................................................2270-001................................2, 12, 14, 16, 18, 20270-0011..........................................................30270-002..........................................12, 14, 16, 18270-004............................................2, 4, 6, 8, 10270-007......2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 26,

3 0 , 3 2 , 3 4 , 3 6270-008............................................................30270-017............................................2, 12, 14, 71270-025........................................................2, 12271-005........2, 4, 6, 8, 10, 14, 16, 18, 22, 38, 40271-008............................................................12271-011............................................................24273-002............................................................22273-006......................................................14, 20280-008............................................................40280-009............................................................38280-151............................................2, 4, 6, 8, 10280-155........................................................2, 12280-201............................................................12300-012..............................................................2

302-014....................................................2, 8, 10302-015..................4, 6, 8, 10, 14, 16, 18, 38, 40302-030............................................................12302-035..............................................................2330-557..............................................4, 6, 46, 70330-866..................................................2, 46, 60330-867............................................4, 10, 46, 62330-868..............................................6, 8, 46, 64330-869............................................8, 10, 46, 66330-936........................................................2, 46331-552..............................60, 62, 64, 66, 68, 70331-559................................................60, 62, 64331-561............................................................70331-564....................................60, 62, 64, 66, 70331-575......................................................68, 70331-578............................................................70331-581............................................................70331-582............................................................70331-587............................................................70331-588............................................................70331-592............................................................70331-593............................................................70331-594............................................................70331-595............................................................70331-596............................................................70331-7012........................................60, 62, 64, 66331-7114........................................60, 62, 64, 66331-8034........................................60, 62, 64, 66331-8035..............................................60, 62, 64331-8039........................................60, 62, 64, 66331-8040........................................60, 62, 64, 66331-8041........................................60, 62, 64, 66331-8042........................................60, 62, 64, 66331-8043........................................60, 62, 64, 66331-8044........................................60, 62, 64, 66331-8045........................................60, 62, 64, 66331-8046........................................60, 62, 64, 66331-8048........................................60, 62, 64, 66331-8049..........................................................60331-8050..............................................62, 64, 66331-8051..........................................................66331-878..............................23, 24, 60, 62, 64, 66331-879..............................23, 24, 60, 62, 64, 66331-880..............................23, 24, 60, 62, 64, 66331-9019..................................60, 62, 64, 66, 70331-933............................................................68331-963............................................................70331-982....................................60, 62, 64, 66, 68331-986............................................................68331-988............................................................68331-991............................................................68331-992............................................................68331-993............................................................68331-994............................................................68


PART INDEX

331-995............................................................68331-996............................................................68331-997............................................................68331-998............................................................68331-999............................................................68340-1001....................................................46, 58340-1002....................................................46, 48340-651......................................................46, 50340-652......................................................46, 52340-860......................................................46, 54340-900......................................................46, 56341-0425....................................................2, 4, 6341-10001........................................................58341-10002..................................................48, 58341-10003........................................................58341-10004........................................................58341-10005..................................................48, 58341-10006........................................................58341-10007........................................................58341-10008........................................................58341-10009........................................................58341-10010........................................................58341-10011........................................................58341-10012........................................................58341-10013........................................................58341-10014........................................................58341-10015........................................................58341-10016..................................................48, 58341-10017..................................................48, 58341-10018........................................................48341-10019........................................................48341-10020........................................................48341-10021........................................................48341-10022........................................................48341-10024........................................................48341-10025........................................................48341-10026........................................................48341-10027........................................................48341-10028........................................................48341-10029........................................................48341-10030........................................................48341-10031........................................................48341-10032........................................................48341-10033........................................................48341-10034........................................................48341-10035........................................................48341-10036........................................................48341-60006..................................................50, 52341-60008..................................................50, 52341-60010..................................................50, 52341-60020..........................48, 50, 52, 54, 56, 58341-60021..........................48, 50, 52, 54, 56, 58341-60043..................................................50, 52341-60067..................................................50, 52

341-60070..................................................50, 52341-60072..................................................50, 52341-60090..................................................50, 52341-60091..................................................50, 52341-60093........................................................50341-60094........................................................50341-60095..................................................50, 52341-60096..................................................50, 52341-60097..................................................50, 52341-60100........................................................52341-60101........................................................52341-6014..............................................50, 52, 54341-616......................................................50, 52341-6235..................................................2, 8, 10341-6236..........................................2, 4, 6, 8, 10341-6247........................................50, 52, 54, 56341-6248........................................50, 52, 54, 56341-6251..............................................50, 52, 54341-6273..........................................................48341-6280..............................................50, 52, 54341-630..........................................50, 52, 54, 56341-6313..........................................................50341-6318....................................................52, 54341-646............................................................54341-653..............................48, 50, 52, 54, 56, 58341-756............................................................58341-80002........................................................54341-80007..................................................50, 52341-80010............................................50, 52, 54341-80013............................................50, 52, 54341-80014........................................................54341-80039........................................................56341-80050........................................................48341-80069........................................................48341-80074........................................................48341-80075........................................................54341-80107........................................................54341-80109........................................................54341-80110........................................................54341-80111.........................................................54341-80112........................................................54341-80113........................................................54341-80114........................................................54341-80115........................................................54341-80116........................................................54341-80117........................................................54341-80118........................................................54341-80119........................................................54341-80121........................................................54341-80123........................................................54341-80124........................................................54341-80125........................................................54341-80126........................................................54341-80127........................................................54


PART INDEX

341-802..............................48, 50, 52, 54, 56, 58341-8086..............................................50, 52, 58341-8087........................................48, 54, 56, 58341-8122..........................................................56341-8125..........................................................56341-8127..........................................................56341-8138..........................................................56341-8182..........................................................48341-901............................................................56341-902............................................................56341-903............................................................56341-904............................................................56341-905............................................................56341-906............................................................56341-907............................................................56341-908............................................................56341-909............................................................56341-911............................................................56341-912............................................................56341-913............................................................56341-914............................................................56341-915......................................................48, 56341-916............................................................56341-917............................................................56341-918............................................................56341-919............................................................56362-019............................................................20362-022................................................16, 18, 20365-001..........................................12, 16, 18, 20365-002............................................................12365-003................................................14, 16, 18365-004........................................................2, 12401-024............................................................24401-028......................................................23, 24401-032......................................................23, 24401-206......................................................28, 30520-1308..........................................................23586-1068..........................................................236251-001....................................................32, 366251-010....................................................32, 366251-011....................................................32, 366251-013....................................................32, 366251-014....................................................32, 36C000-001..........................................................12C000-006..........................................................40C000-013............................................................2C000-132..........................................................12C000-144..........................................................23C000-146..........................................................24C000-201..........................................................24C306-137............................................................2C306-138............................................................2C320-128..........................................................20C502-136..........................................................10

C502-137............................................................8C520-118..........................................................12C520-168............................................................2C742-101............................................................2C742-106..........................................................12C742-107..........................................................12C742-110..........................................................12C742-112..........................................................12C742-113..........................................................12C742-114..........................................................20C742-115..........................................................20C742-116..........................................................20C742-117..........................................................20C742-118..........................................................20C742-119..........................................................20C742-121..........................................................14C742-122....................................................16, 18C742-123....................................................16, 18C742-124..........................................................14C742-125..........................................................14C742-126..........................................................16C742-127..........................................................18C742-128..........................................................16C742-129..........................................................18C742-130....................................................16, 18C742-131..........................................................14C742-132..........................................................14C742-133..........................................................14C742-134..........................................................14C742-135..........................................................14C742-136..........................................................14C742-137........................................................4, 6C742-138........................................................4, 6C742-139..........................................................14C742-140..........................................................14C742-141....................................................16, 18C742-142....................................................16, 18C742-143..........................................................12C742-144..............................................16, 18, 20C742-145..........................................................12C742-146..........................................................14C742-150............................................................4C742-151............................................................8C742-152............................................................8C742-155............................................................6C742-156..........................................................10C742-157..........................................................10C742-164........................................................4, 6C742-165..........................................................12C742-166..........................................................12C742-167..........................................................12C742-168......................................................8, 10C742-169......................................................8, 10C742-170............................................................2


PART INDEX

C742-171............................................................2C742-181..................................................2, 8, 10C742-183......................................................8, 10C742-184......................................................8, 10C742-185............................................................2C742-187..............................................16, 18, 20C742-188............................................................2C742-189..........................................................14C742-190..........................................................14C742-191............................................................2C742-192......................................................8, 10C742-193............................................................2C742-194............................................................2C742-195............................................................2C742-196....................................................16, 18C742-197..........................................................14C742-201............................................................2C742-202............................................................2C742-203............................................................2C742-205....................................................12, 14C742-206....................................................12, 14C742-207..............................................16, 18, 20C742-209....................................................16, 18C742-213......................................................8, 10C742-214............................................................2C742-216......................................................8, 10C742-218........................................................4, 6C742-219........................................................4, 6C742-221..........................................................26C742-222..........................................................26C742-223..........................................................26C742-224..........................................................26C742-225..........................................................26C742-226..........................................................26C742-227..........................................................26C742-228..........................................................26C742-229..........................................................26C742-230..........................................................26C742-231..........................................................26C742-232..........................................................26C742-233..........................................................26C742-234..........................................................26

C742-235..........................................................26C742-238..........................................................26C742-240..........................................................26C742-241..........................................................26C742-242..........................................................26C742-243..........................................................26C742-244..........................................................14C742-271....................................................28, 30C742-272....................................................28, 30C742-273....................................................28, 30C742-276....................................................28, 30C742-277....................................................28, 30C742-278....................................................28, 30C742-279....................................................28, 30C742-280....................................................28, 30C742-281....................................................28, 30C742-501....................................................32, 36C742-502....................................................32, 36C742-503....................................................32, 36C742-504....................................................32, 36C742-505....................................................32, 36C742-551....................................................34, 36C742-552....................................................34, 36C742-553....................................................34, 36C742-554....................................................34, 36C742-555....................................................34, 36C742-556....................................................34, 36C742-557....................................................34, 36C742-558..........................................................34C742-559..........................................................34C742-560..........................................................34C742-571....................................................34, 36C742-572....................................................34, 36C742-573....................................................34, 36C742-574....................................................34, 36C742-575..........................................................34C742-860..........................................................12S000-012....................................................12, 72S000-082..........................................................12S000-092....................................................14, 71S000-101....................................................14, 71S000-110............................................................2


PART INDEX

FX742 C742-010PPrinted in Canada

LUKE HP

NESSA LABEL

FX742 - NESSA, Inc...59 365-004 4 MLGBushing1.75x1.25x1.5lg 60 257-045 8 Insert,1/2",.063-.200Wall...

Documents

Transcript of FX742 - NESSA, Inc...59 365-004 4 MLGBushing1.75x1.25x1.5lg 60 257-045 8 Insert,1/2",.063-.200Wall...