Fusjitsu 5750 Cleaning & Consumables Replacement
-
Upload
dennis-lee -
Category
Documents
-
view
220 -
download
0
Transcript of Fusjitsu 5750 Cleaning & Consumables Replacement
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
1/11
for Fujitsu Scanners
Cleaning and Consumable Replacement InstructionsI Manualnstruction
Versitec is a division of Cranel, Inc.
fi-5750C/fi-5650C
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
2/11
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
3/11
1
INSTRUCTION MANUAL FOR
FUJITSU
fi-5750 C/fi-5650C SCANNER
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
4/11
2
Cleaning the ADF Components ........................................... 3
Cleaning the Flatbed .......................................................... 5
Cleaning the ADF Components ........................................... 5
Replacing the Brake Rollers ................................................. 6
Replacing the Pick Rollers .................................................... 7
F I -5750 C S C A N N E R
TA BLE OF CONTENTS
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
5/11
3
CLEANINGANDREPLACINGCONSUMABLES
Cleaning the Automatic Document Feeder (ADF) Components
CAUTION
Disconnect the scanner from power outlet
CAUTION
Allow the glass in the ADF to cool for at least three
minutes before cleaning it
Press the two blue buttons to open up the ADF compartment
Use a clean cloth moistened with V1 cleaner to wipe the entire
surface of these components:
a. brake rollers - you may want to open the brake roller
compartment to clean these rollers as they are difficultto turn
b. pick rollers - turn one roller while wiping the surface of
the other roller down.
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
6/11
4
Clean these components with the cloth moistened with V1 cleaner as well:a. chute roller
b. pick arm
c. feed rollers
d. sheet guide
e. glass flats
Clean the plastic rollers with F2 cleaner
Gently close the ADF after allowing the ADF components to dry for a few
.setunim
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
7/11
5
Cleaning the Flatbed
Press on the flatbed cover handle and carefully lift up until the
cover stays open so that you can access the glass surface.
Wipe the glass surface with a clean cloth moistened with V1 cleaner
Allow the glass surface to dry for a few minutes
Gently close the flatbed cover and resume scanner operation
Using a Cleaning Sheet to Clean the ADF Components
Leave the scanner connected to the power outlet.
Let the glass surface cool a few minutes if the scanner has been in
operation recently
Moisten a cleaning sheet with V1 cleaner and feed it through the scanner .
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
8/11
6
Repeat this until the sheet is noticeably dirty.
Discard the cleaning sheet
REPLACING THECONSUMABLES
Replacing the Brake Rollers
Press the two blue buttons to open the ADF
Open the brake roller compartment door
Lift the brake roller set from the door. Note the orientation of the shiny
black roller on the left side of the compartment door.
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
9/11
7
Install the new brake roller set into the door with the shiny black roller on
the left.
Close the brake roller compartment door. If you encounter any resistance
dellatsnisitesrellorekarbehttahterusekam,roodehtgnisolcni
.ylreporp
Close the ADF and resume scanner operation
To reset the Brake Roller Counter see your scanner manual or consult with
your computer software support department.
Press the two blue buttons to open the ADF
Replacing the Pick Rollers
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
10/11
8
Open the Pick Roller compartment door using your thumb
Slide one pair of pick rollers to the right to remove it from the shaft and
replace it with the matching set from your kit. The smoother, smaller, set
of rollers are the first in the paper path, followed by the larger, treaded
rollers.
Make sure that the notch on the roller set lines up with the screw on the
.ylreporpnrutsrellorehttahtserussasihT.tesrellorhcaefotfahs
Close the Pick Roller compartment door. If the door doesnt completely
close and lie flat, check that the two sets of rollers are installed properly.
Close the ADF and resume scanner operation.
To reset the Pick Roller Counter see your scanner manual or consult with
your computer software support department.
-
7/24/2019 Fusjitsu 5750 Cleaning & Consumables Replacement
11/11
For inquiries on consumables, call Versitec at: 888.722.6548
Corporate Headquarters
8999 Gemini ParkwayColumbus, OH 43240
Fax: 614.431.8388
Repair Center
908 Boston Turnpike RoadShrewsbury, MA 01545
Fax: 508.460.1890
Western Region Office
8001 Irvine Center Drive, 4th FloorSuites 411, 412, 413
Irvine, CA 92618
www.versitec.com