FUNCTION SELECTION - lofisneon.lofis.net/SsangYong/Service_Manuals/Actyon/ActyonA0... ·...
Transcript of FUNCTION SELECTION - lofisneon.lofis.net/SsangYong/Service_Manuals/Actyon/ActyonA0... ·...
30 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
FUNCTION SELECTION
Check the Trouble Code
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “1] TROUBLE CODE” and press “ENTER” in“FUNCTION SELECTION” screen.
2. The “DIAGNOSTIC TROUBLE CODEs” screen isdisplayed and it shows the trouble.
3. When selecting a trouble code, then
if you press “ ”: Displays the sensor data for thedetected trouble (Freeze FrameMode).
if you press “ ”: Displays the help tips for thedetected trouble.
• If there is not any fault, “NO TROUBLE DETECTED”message appears.
NOTE
31SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
Sensor Data Check
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “2] DATA LIST” and press “ ” in “FUNCTIONSELECTION” screen.
2. The screen shows approx. 57 sensor data.
3. Select the items you want to see and press “ ”key to freeze them.
• You can freeze up to 5 items (*: selected items).NOTE
32 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
Actuator Check
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “3] ACTUATOR” and press “ ” in “FUNCTIONSELECTION” screen.
2. The screen shows 19 items. Select the item you wantto see and press “ ”.
3. For example, if you select “02] GLOW PLUG” itemand press “ ”, the screen as shown in figure isdisplayed.
33SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
4. If you want to operate the glow plug relay, press“ ” key. The “ACTIVATING” message appears andthe relay operation alarm sounds.
5. If the system operates normally, Scan-100 displays“GOOD”.
6. If you want to stop the operation press “ ” key inkeyboard.
34 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
Trouble Code Clear
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “1] TROUBLE CODE” and press “ ” in“FUNCTION SELECTION” screen.
2. The “DIAGNOSTIC TROUBLE CODEs” screen isdisplayed and it shows the trouble.
3. Fix the trouble and go back to “1] TROUBLE CODE”screen and check if the trouble has been changedto “H (History trouble code)” code.
• C = Current trouble, H = History trouble
NOTE
35SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
4. If the trouble has been change to “H (History troublecode)” code, press “ ” key to go back to “FUNCTIONSELECTION” screen. In this screen, select “4] TROUBLECODE CLEAR” and press “ ”.
5. The “TROUBLE CODE CLEAR” screen is displayed.If you press “ ”, only the history trouble codeswill be cleared.
• Current trouble codes will not be cleared.
• Check the trouble codes after clearing the troublecodes.
NOTE
36 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ECU Identification
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “5] ECU IDENTIFICATION” and press “ ”in “FUNCTION SELECTION” screen.
2. The “ECU IDENTIFICATION” screen that shows theVIN, ECU software number, ECU software versionand programming date is displayed.
3. If you replaced the ECU, press “ ” to input thevehicle identification number.
37SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
Injector (C2I) Corrections
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “6] INJECTOR (C2I) CORRECTIONS” andpress “ ” in “FUNCTION SELECTION” screen.
2. The “INJECTOR (C2I) CORRECTIONS” screen thatshows current C2I coding values of #1 to #4 injector isdisplayed.
• If the injector/ECU has been replaced or the injec-tor system defective is suspected, go to C2I Cod-ing item and check the injector and coded injectorC2I value.
NOTICE
3. If you replaced the ECU, enter the C2I value of therelevant injector.
38 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
1) If you enter the invalid C2I value of the relevantinjector, the message as shown in figure appearswith alarm sound.
2) If you enter the valid C2I value of the relevantinjector, the message as shown in figure appearswith alarm sound.
• If you want to go back to previous screen, press
“ ” key. You can see the previous C2I value.
NOTE
• The C2I value of replacing injector is recorded inthe label.
• C2I coding number: 16 digits (ex, B1 B9 D4 1B 43C6 0E 4F)
NOTE
39SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
Leak Detection
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “1] LEAK DETECTION” and press “ ” in“FUNCTION SELECTION” screen.
2. The “LEAK DETECTION” screen that shows thechecking conditions as shown in figure is displayed.
• This item is for checking the high fuel pressure af-ter the IMV supply line of HP pump in DI engine fuelsystem. If you still suspect that the fuel pressuresystem is defective even after no trouble isdetected, perform the fuel pressure test again byusing a fuel pressure tool kit.
NOTE
40 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
Preceding page
41SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
Variant Coding
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “8] VARIANT CODING” and press “ ” in“FUNCTION SELECTION” screen.
2. When the “VARIANT CODING” screen is displayed,select “1] READ VARIANT VALUE” and press “ ”.
3. Select “1] ENGINE VARIANT CODING” and press“ ” in “FUNCTION SELECTION” screen.
42 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
4. The “VARIANT CODING” screen that shows currentlyequipped devices is displayed.
ENGINE
CHASSIS
43SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
ECU coding completed
Supplementary heater(PTC)
Auto cruise
Immobilizer
Remote starter
Vehicle speed signal
ABS or ESP
TOD/Part time TC (4WD)
Air conditioner
Neutral signal input(M/T “N” signal)
Engine Related Coding Item
DescriptionVariant Coding Item Selection
NO/YES
NO/YES
NO/YES
NO/YES
NO/YES
CAN/WIRE
NO/YES
NO/YES
NO/YES
NO/YES(WIRE)/CAN
Engine model
DOM/EXP
Telematics
Selector lever
Transmission
ABS/EBS
SSPS
Transfer case (4WD)
Sedan/Limousine
Vehicle type
Coding
EAS
EPB
TPMS
DescriptionVariant Coding Item Selection
Select the appropriate engine.
Select the region.
W/ Telematics: YesW/O Telematics: No
Select the appropriate system.
Select the appropriate selector lever.(For DI engine equipped vehicle, select “ION (BTRA)”)
Select the appropriate system.
Select “ ” only for the vehicle with ECPS system.
Select the appropriate system.
Select “SEDAN” - Automatic coding.
Select “ACTYON” - Automatic coding.
Select the coding status.
Select the appropriate system.
Select “Yes” only for the vehicle with EPB system.- Automatic coding
Select “ ” only for the vehicle with TPMS system.
D20DT/G23D
DOM/GENERAL/EU
Yes/No
MT/DC5AT/BTRA AT
ION(BTRA)/DC LE-VER/DURA LEVER
NA/ABS/TCS/ESP
NO/YES
NA/TOD/PT 4WD/AWD/PT 4WD (W/O 4L)
SEDAN/LIMOUSINE
ACTYON
CODING COMPLETED
NA/ECS/EAS(2)/EAS(4)
NO/YES
NO/YES
Chassis Related Coding Item
“ ” is automatically selected.
Select “ ” only for the vehicle with PTC type supple-mentary heater (in DI engine).
Select “ ” only for the vehicle with auto cruise system.
Select “ ” only for the vehicle with immobilizer system.
No remote starter system is applied to this model.However, must select “ ” to confirm that this vehicledoesn’t have remote starter.
CAN Select.
Select “ ” only for the vehicle with ABS or ESP system.
Select “ ” only for the vehicle with part time TC system.
Select “ ” only for the vehicle with A/C system.(W/O Aircon : NO)
Select “ ” only for the vehicle with M/T neutral switch.
44 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
4. If you need to change the variant coding, press “ ”key to go back to “VARIANT CODING” screen. In thescreen, select “2] WRITE VARIANT CODING” andpress “ ”.
5. When the “WRITE VARIANT CODING VALUE” screenis displayed, change the item by using arrow keys.
6. If you press “ ”, the message as shown in figureappears. And, then “VARIANT CODING” screen isdisplayed.
7. Follow the instructions on the display of Scan-100.
45SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
8. Select “READ VARIANT VALUE” to see the codingcoded value.
* Chassis variant coding should be done in the sameprocedures as for Engine variant coding.
46 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ECU Replace
Preceding Work: Perform the “Entering DiagnosisProcedures”
1. Select “9] MISCELLANEOUS” and press “ ” in“FUNCTION SELECTION” screen.
4. When the “ECU REPLACE (STEP 2)” screen isdisplayed followed by “ECU REPLACE (STEP 1)screen, turn the ignition “OFF” and remove thecurrently installed ECU.
3. Before starting ECU replace, check the ECU S/Wversion of old ECU and new ECU.
• Do not turn off the Scan-100 at this time.
• Record the below data:
1) Vehicle identification number
2) Variant coding value
3) C2I coding value
4) Multi calibration
NOTICE
2. Select “3] ECU REPLACE” and press “ ” in“FUNCTION SELECTION” screen.
47SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
7. In “MULTI CALIBRATION” screen, select the releventmodel.
6. If you turn the ignition switch to “ON” position and press “ ”, the message as shown in figure 1 (systeminitialization) appears, and then “MULTI CALIBRATION” screen (figure 2) is displayed.
figure 1 figure 2
5. Install the new ECU.
48 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
9. If the multi calibration is completed successfully,“ECU REPLACE (STEP 5) screen is displayed.
Backup data:
1) Multi calibration value
2) VIN value
3) Variant code value
4) Injector (C2I) value
10. In immobilizer equipped vehicle, the immobilizercoding should be done after completed the multicalibration.
8. When you press “ ”, the processing messageas shown in figure appears.
49SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
11. Press “ ” for the vehicle equipped with immobilizer system.
12. Follow the instructions on the display of Scan-100.
- Identification of VIN number
- Immobilizer coding
# 1 # 2
# 3# 4
# 6# 5
50 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
# 7 # 8
# 9# 10
# 12# 11
51SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
13. Press “ ” to return to “MAIN MENU” screen.
52 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ECU Replace (Scan-100Communication is not available)
If the Scan-100 communication is not available due toECU failure, replace the ECU as follows.
1. Replace the ECU with new one.
4. VIN/Variant Data/C21 Data is not read from ECU.Press “ ” to run the multi calibration.
2. Select “3] ECU REPLACE” and press “ ” in“FUNCTION SELECTION” screen.
3. If the versions of ECUs are not matched, program thenew ECU after replacement.
53SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
6. If the multi calibration is completed successfully,the message screen shown in the figure isdisplayed.
7. The VIN/Variant Data/C21 Data should be inputmanually.
8. To enter the data, press “ESC” on the screen inStep 5 and go back to main screen.
9. To enter the VIN, select “5] ECU IDENTIFICATION”and press “ ”.
10. Press “ ” and enter the VIN again.
5. Select the appropriate model in “MULTI CALIBRATIONSELECTION” screen.
1) Vehicle with A/T: 2] Dom/Gen A/T
2) Vehicle with M/T: 4] Dom/Gen M/T
54 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
12. Select “6] INJECTOR (C2I) CORRECTIONS” andpress “ ” in “FUNCTION SELECTION” screen.Remove the engine acoustic cover and enter the16 digits code on each injector label for all of fiveinjectors. If any of digits is wrong, you should enterfull code again. Make sure that the VIN code iscorrect. The nearest injector from the radiator isnumber 1 and the number goes higher as it movesaway.
13. Select “8] VARIANT CODING” and press “PRESS”in “FUNCTION SELECTION” screen. When the“VARIANT CODING” screen is displayed, select“2] WRITE VARIANT CODING” and press “PRESS”.When the “WRITE VARIANT CODING” screen isdisplayed, change the item by using arrow keys.
11. Enter the VIN into the number plate on the screen.To change the number to the character, use thearrow keys.
55SCAN-100
SC
AN
EC
U
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSISACTYON SM - 2006.03
Rail Pressure Reset
Rail Pressure Reset Procedures
The engine ECU needs a specific amount of fuel according to the fuel supply lines and vehicle driving conditions.
However, if the fuel supply (pressure) is not achieved due to, for instance, defective fuel system, ECU desig-nates the offset value to the high pressure pump to compensate it.
The fuel supply pressure varies according to the offset value and the engine output could be decreased due tothis variation. When the engine output decreases, check whether all rail pressure offset values is set to 0 in theRail Pressure Reset screen in SCAN-100. If the setting value is not 0, measure the fuel pressure with a tester.If any defective is found, repair the affected components and reset the rail pressure offset value to 0.
The rail pressure reset procedures should be done after replacing any high pressure pump and fuelsystem related components.
1. Select the vehicle model.
2. Select “2] RAIL PRESSURE RESET” in “FUNCTIONSELECTION” screen.
56 SCAN-100
DIAGNOSISACTYON SM - 2006.03
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
3. Enter the current rail pressure value and press[ENTER] to reset the offset value.
4. The screen returns back to step 3 after displayingthe [RAIL PRESSURE RESET IS SUCCESSFUL]message.
• If the offset value is not set to 0, check the fuel pres-sure and other DTC generations before starting therail pressure reset operation.
NOTICE