Fully Integrated 36” MasterCool - Miele · Fully Integrated 36” MasterCool Please note the...

Fully Integrated 36” MasterCool

All Refrigerator:

K 2901 Vi / K 2911 Vi

All Freezer:

F 2901 Vi / F 2911 Vi

Bottom Mount:

KF 2901 Vi / KF 2911 Vi

French Door:

KF 2981 Vi

8mieleusa.comSpecification Sheets TRS 05202019 Please note: This information is subject to change

Shown: KF 2981 Vi


Please note the following:• This specification sheet is for a single built-in unit.• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specification sheet. *If design calls for a partition less than 6 5/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of the Heating Mat/Merge Kit.

SPECIFICATIONS

Overall Unit Dimensions 353/4” (908 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Depth does not include door panel]

Niche

Minimum Cabinet Niche Opening 36” (915 mm) W* x 84” - 853/16” (2134 - 2164 mm) H x 243/4” (629 mm) D

Electrical K 29x1 Vi F 29x1 Vi KF 29x1 Vi

Electrical Requirements110V / 120V, 60Hz, 15 Amps

In the case of side-by-side installations, a separate outlet must be used for each appliance.

Power Cord NEMA 5-15 plug, 5 ft (1.52 m)

Plumbing K 29x1 Vi F 29x1 Vi KF 29x1 Vi

Water Supply Requirements -

Connect to a cold water supply only. Do not connect to a low-mineral or a reverse osmosis system. Must be connected to a shut-off valve. The water shut-off valve must be accessible after installation. The water pres-sure must be between 29 psi (2 bar) and 116 psi (8 bar). If the pressure is higher than 120 psi (8.3 bar), a pressure reducing valve must be installed.

Water Connection Line - Standard 1/4” O.D flexible water line. The maximum outer diameter of the water pipe (without fittings): 3/8” (10 mm). Water line is not included.

Shipping K 29x1 Vi F 29x1 Vi KF 29x1 Vi

Shipping Weight 435 lbs (197 kg) 462 lbs (210 kg) 507 lbs (230 kg)

Shipping Dimensions 40” (1016 mm) W x 8913/16” (1,294 mm) H x 291/4” (800 mm) D

Support

Call Miele (800) 999-1360

Miele Website 8www.mieleusa.com

20/20 Link 82020technologies.com

K 2901 Vi (Right Hinged)Item 36290101USA

K 2911 Vi (Left Hinged)Item 36291101USA

F 2901 Vi (Right Hinged)Item 37290101USA

F 2911 Vi (Left Hinged)Item 37291101USA

KF 2901 Vi (Right Hinged)Item 38290101USA

KF 2911 Vi (Left Hinged)Item 38291101USA

of 12

KF 2981 Vi (French Door)Item 38298101USA

CUTOUT DIMENSIONS

• Niche depth assumes a 3/4” (19 mm) panel, please adjust according to custom panel thickness


CUTOUT DETAILS

• The electrical connection must not be positioned higher than 9” (228.6 mm) above the floor.

• The 1/4” (6.4 mm) plumbed water connection should not be positioned higher than 2” (50.8 mm) above the floor.

Notes:In case of an emergency the electrical outlet must be easily accessible and must not be concealed behind the appliance.

of 12

POWER SUPPLY AND WATER CONNECTION(Water Connection For F 29x1 Vi & KF 29x1 Vi Only)


Water connection is located in front of unit.1/4” compression fitting is needed.

Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp - NEMA 5-15 molded plugWater line - 1/4” flexible water line - not included

Rear View Front View

Electrical Connection

Side View

of 12

CUSTOM PANEL INSTALLATIONS

Width: 29 3/4" in all cases

Thickness: Minimum 3/4" outside frame

Height: Determined using the following calculation:

Panel Height = HOC - TKH

HOC = Total height of cabinet or side panelTKH = Toe-kick height

Note: Finish back side of panels to insure appearancePanel may extend above unit. This is notconsidered in height calculation

Maximum panel weight: 105.8 Pounds

MieleFully Integrated

Freezer

TKH

HO

C

Pane

l Hei

ght

These units do not come equipped with a front panel. They are designed to accept a custom door panel supplied bythe cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surroundingcabinets.

Panel size is determined in the following manner:

Panel NotesIf the adjoining cabinets are taller than the height of machine (HOM) - the front panel may be extended accordingly.Simply maintain the toekick height and extend the panel the needed distance.

Adjoining cabinet

Machine

Extended Panel

106 Pounds

Minimum 35 3/4” (908 mm)

Minimum 3/4” (19 mm) outside frame

Fully Integrated 36” MasterCool | K 29x1 Vi & F 29x1 Vi

of 12

Fully Integrated 36” MasterCool | K 29x1 Vi & F 29x1 Vi

DOOR PANEL DIMENSIONSKFP 3604 - Door Panel

Available as an accessoryfor the following models:• K 29x1 Vi• F 29x1 Vi

of 12

Pan

el "

B"

Hei

ght

Width: 29 3/4" in all casesThickness: Minumum 3/4" outside frame

Standard Upper Panel Height: 53 5/16"


Upper Maximum panel weight : 103.6 Pounds

Lower Panel Height: Use the following calculation:

Panel Height = HOM - 53 9/16 - TKH

HOM = Total height of machine. Can be adjusted tomatch adjoining cabinets - typically 84"HOM is adjustable between 83 1/2" - 85 3/8"

TKH = Toe-kick height (2" - 8 3/8")

Lower Maximum panel weight: 22 Pounds

Upper Panel

TKH

HO

M

Pan

el H

eigh

t



Lower Panel

Upper Panel NotesIf the adjoining cabinets are taller than the height of machine (HOM) - the upper panel may be extended accordingly.Find the difference between height of the adjoining cabinets and the height of machine (HOM) and add to 53 5/16"

Adjoining cabinet

Machine

Extended Panel Example:Ajoining cabinet height: 87"Height of machine: 84"Difference: 3"

Extended panel height: 56 5/16"


Pan

el "

B"

Hei

ght










Upper Panel

TKH

HO

M

Pan

el H

eigh

t



Lower Panel


Adjoining cabinet

Machine



104 lbs

HOM - 51 1/2” (1307 mm) - TKH

51 3/8” (1304 mm)

Minimum 35 3/4” (756 mm)Minimum 3/4” (19 mm) outside frame

87” (2210 mm)84” (2134 mm)3” (76 mm)

54 1/2” (1379 mm)

Total height of machine. Can be adjusted to match adjoining cabinets - typically 84” (2133 mm).HOM is adjustable between 84” -85 3/16” (2134 mm - 2164 mm)

Lower Maximum panel weight: 22 lbs

Toe-kick height 2” - 8 3/8” (51 - 212 mm)TKH =

Fully Integrated 36” MasterCool | KF 2901 Vi / KF 2911 Vi

of 12

Fully Integrated 36” MasterCool | KF 2901 Vi / KF 2911 Vi

DOOR PANEL DIMENSIONSKFP 3614 - Top PanelKFP 3624 - Bottom Panel

Available as an accessoryfor the following models:• KF 2901 Vi / KF 2911 Vii

of 12

Pan

el "

B"

Hei

ght










Upper Panel

TKH

HO

M

Pan

el H

eigh

t



Lower Panel


Adjoining cabinet

Machine




104 lbs

HOM - 51 1/2” (1307 mm) - TKH

51 3/8” (1304 mm)

Minimum 35 3/4” (756 mm)Minimum 3/4” (19 mm) outside frame

87” (2210 mm)84” (2134 mm)3” (76 mm)

54 1/2” (1379 mm)

Total height of machine. Can be adjusted to match adjoining cabinets - typically 84” (2133 mm).HOM is adjustable between 84” -85 3/16” (2134 mm - 2164 mm)

Lower Maximum panel weight: 22 lbs

Toe-kick height 2” - 8 3/8” (51 - 212 mm)TKH =

Fully Integrated 36” MasterCool | KF 2981 Vi

of 12

Minimum 17 13/16” (452.5 mm)

Fully Integrated 36” MasterCool | KF 2981 Vi

DOOR PANEL DIMENSIONSKFP 3634 - Top PanelsKFP 3624 - Bottom Panel

Available as an accessoryfor the following models:• KF 2981 Vi

of 12

HINGING DETAILS

HINGING DETAILS 115° OPENING


Available for the following models:• K 29x1 Vi• F 29x1 Vi• KF 29x1 Vi

of 120-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09

snoitpo ssenkcihTsnoitpo ssenkcihT

Door Swing

NOTE: Additional space needed depending onthickness of front panels and handle used

38 11

/16"

7/16"

Door Swing

16 7/8"MAX


3”(76.2mm)

1-3/4”(44.5mm)

1-3/8”(35mm

)1-1/6” (29.6m

m)

1/4”(6.4mm

)17/24” (18m

m)

2-1/24”(52mm)2-1/3” (59mm)2-5/8” (67mm)

3”(76.2mm)

1-3/4”(44.5mm)

1-3/8”(35mm

)1-1/6” (29.6m

m)

1/4”(6.4mm

)17/24” (18m

m)

2-1/24”(52mm)2-1/3” (59mm)2-5/8” (67mm)

0-3/4” (19 mm

)1” (25 m

m)

1-1/4” (32 mm

)1-1/2” (38 m

m)

1-3/4” (44 mm

)

1-1/2” (38 mm)

1-1/4” (32 mm)

1” (25 mm)

0-3/4” (19 mm)

0-1/8” (3 mm)

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 1

1/16

"

7/16"

Door Swing

16 7/8"MAX


DOOR SWING AT 115° OPENING 11 3/4”(298 mm)

MaxAvailable for the following models:• K 29x1 Vi• F 29x1 Vi• KF 2901 Vi / KF 2911 Vi

HINGING DETAILS 90° OPENING

Specification Sheets TRS 05202019


Available for the following models:• K 29x1 Vi• KF 29x1 Vi

of 12

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 11

/16"

7/16"

Door Swing

16 7/8"MAX


7/16”(11 mm)

1-3/16”(30mm)

1-7/16”(36.5mm)

1-11/16”(43mm)

1-15/16”(49.2mm)

Handle or object that is NOT flush with Cabinet Front.

0-3/4” (19 mm

)1” (25 m

m)

1-1/4” (32 mm

)1-1/2” (38 m

m)

1-3/4” (44 mm

)2” (51 m

m)

0-3/4” (19 mm)

1” (25 mm)

1-1/4” (32 mm)

1-1/2” (38 mm)

0-1/8” (3 mm)

When installing hinge side next to an appliance or object that is within range of the door panel, limit the door opening angle to 90°. This is done by installing the banking pin as illustrated. Insert the banking pin through the holes and drive in with a hammer.

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing

32 1

1/16

"

7/16"

Door Swing14 3/8"MAX

NOTE: Additional space needed depending on the thicknessof front panels and handle used.Freezer units cannot be stop pinned at 90°

NOTE: Additional space needed depending on the thicknessof front panels and handle used.Freezer units cannot be stop pinned at 90°

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 1

1/16

"

7/16"

Door Swing

16 7/8"MAX


DOOR SWING AT 90° OPENING 7/16” (11 mm)

38 11

/16” (

982

mm

)

Available for the following models:• K 29x1 Vi• KF 2901 Vi / KF 2911 Vi

Fully Integrated 36” MasterCool - Miele · Fully Integrated 36” MasterCool Please note the...

Documents

Transcript of Fully Integrated 36” MasterCool - Miele · Fully Integrated 36” MasterCool Please note the...