User Manual Fujitsu IoT Solution

Ubiquitousware

FUJITSU IoT Solution UBIQUITOUSWARE®

Location Unit (L)

Thank you for buying an innovative product from

Fujitsu.

The latest information on our products as well as tips, updates, etc., can be found on our website at: http://www.fujitsu.com/usYou can find driver updates and support documentation at:

http://solutions.us.fujitsu.com/www/content/support/mobile/IoT/index.phpShould you have any technical questions, please contact our Hotline/Service Desk at:

http://www.fujitsu.com/us/about/local/corporate/subsidiaries/fai/contact/mobile-support.html● Your authorized distributor

● Your sales office

We hope you enjoy using your new Fujitsu system!

Published by / Contact address in the EU Published by / Contact Address in the Americas

FUJITSU AMERICA, INC.Address: 1250 East Arques Avenue Sunnyvale, CA 94085-3470, U.S.A. Telephone: 800 831 3183 or 408 746 6000 Website: http://solutions.us.fujitsu.com Contact Form: http://solutions.us.fujitsu.com/contact

Copyright© 2016 Fujitsu America, Inc.All rights reserved.

Edition date

10/2016

Order no.: FPC58-3284-01, Edition 1

Location Unit (L)

User Manual

4 5 9

10 24

Ports and controls Important notes First-time setup of your device Using the device Troubleshooting and tips Manufacturer’s notesDeclarations of Conformity

25 27

Remarks

Notes on the product description are consistent with the design specifications from Fujitsu and are made available for comparison purposes. The actual results may differ due to several factors. Technical data is subject to change without notification. Fujitsu does not accept any responsibility for technical or editorial errors or omissions.

Trademarks

Fujitsu and the Fujitsu logo are registered trade marks of Fujitsu Limited or its subsidiaries in the United States and other countries.

UBIQUITOUSWARE is a trademark of FUJITSU LIMITED.

The Bluetooth® smart ready word mark and logos are owned by the Bluetooth SIG, INC.

All other trademarks mentioned here are the property of their particular owner.

Copyright

No part of this publication may be copied, reproduced or translated without prior written permission from Fujitsu.

No part of this publication may be stored or transmitted in any electronic manner without written permission from Fujitsu.

Fujitsu 3

Notational conventions

Pay particular attention to text marked with this symbol. Failure to observe these warnings could pose a risk to health, damage the device or lead to loss of data. The warranty will be invalidated if the device becomes defective through failure to observe these warnings.

Indicates important information for the proper use of the device.

► Indicates an activity that must be performed

Ports and controls

4 Fujitsu

Ports and controls This chapter presents the individual hardware components of your device. It gives you an overview of the device’s indicators and connections. Please familiarise yourself with these components before you start to work with the device. Main Unit Front

Rear

Power button

Sensor hole

Atmospheric sensor hole

The charging terminal is located on the base of the unit.

Notification LED

Important notes

Fujitsu 5

Important notes I

Here you will find essential safety information regarding your device. The other notes provide useful information on your device.

Safety notes Please follow the safety notes provided in the "Safety/Regulations" manual as well as the safety notes given below.

When connecting and disconnecting cables, observe the relevant notes in this user manual.

This device complies with the relevant safety regulations for data processing equipment. If you have questions about using your device in a particular area, please contact your sales outlet or our Hotline/Service Desk.

High Safety Required Use This Product is designed, developed and manufactured as contemplated for general use, including without limitation, general office use, personal use, household use, and ordinary industrial use, but is not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury, severe physical damage or other loss (hereinafter “High Safety Required Use”), including without limitation, nuclear reaction control in a nuclear facility, aircraft flight control, air traffic control, heavy transport logistics, medical life support system, missile launch control in weapon systems. You shall not use this Product without securing the sufficient safety required for the High Safety Required Use.

Additional safety notes for devices with wireless components Your device is equipped with transmitter components. When handling your device, observe the following safety notes:

• Switch off the device if you cannot rule out that the radio waves transmitted could affect otherelectrical and electronic appliances in your vicinity, such as medical equipment, (distance fromheart pacemakers at least 20 cm), aircraft systems, or could cause an explosion or fire (e.g.filling station, paint shop).

For information on how to switch radio components on and off, see chapter "Switching the wireless components on and off", Page 10

Important notes

6 Fujitsu

Health and safety General

• This product is not for medical use.

• Do not disassemble or modify the product. Otherwise, the product could be damaged and electrical shock or fire could occur. In such cases, Fujitsu shall bear no responsibility for any damage incurred by the user.

• The device may only be connected to a freely accessible earthed/grounded AC outlet, the power socket on the device must be freely accessible.

• No cables should be connected or disconnected during a thunderstorm.

• In emergencies, switch the device off immediately, disconnect the AC plug and inform your sales outlet or the Fujitsu Service Desk.

• Use only the supplied/authorized AC adapters and/or AC cables. If necessary, replace the supplied power cable with an equivalent power cable which meets national regulations.

• The sensor unit is waterproof/dust proof. However, do not allow this device, its accessories or optional devices to become wet or dusty. The AC adapter, Desktop charger and USB Cable are not waterproof/dust proof.

Bluetooth devices

• This device is equipped with Bluetooth- compliant communication security features. Theeffectiveness of these features depends upon various settings. Be aware of security risks duringBluetooth communication.

• Fujitsu assumes no responsibility for any information that may be leaked during Bluetoothcommunication.

Before using this device, check whether other radio stations are in operation in your neighbourhood.

If radio interference occurs between this device and other radio equipment, use this device in a different location, or turn the radio equipment off to stop the interference.

WARNING

• Do not place this device in fire or a heating or cooking appliance, such as a microwave oven orhigh-pressure cooker.

• Do not throw the device, or subject it to excessive force or shock.

• Do not use cleaning sprays (that include flammable substances) to clean this product

• Avoid subjecting the product to strong impacts or drops. Damage to the product and seriousaccidents such as fire or electrical shorts could occur.

Important notes

Fujitsu 7

• Do not store the product in environments that are subject to high temperature or high humidity, or in locations that are subject to direct sunlight for long periods of time. Additionally, severe changes in ambient temperature could result in internal condensation, which can cause the product to malfunction.

• When charging is complete, be sure to remove the charging cable. Even if charging is not complete, remove the cable when the required charging time has elapsed.

• Keep electrically conductive materials (metallic items, pencil lead, etc.) from coming in contact with the sensor holes or charging terminal.

• If the device gives off a strange smell, overheats, or becomes discolored or deformed during use, while charging or when stored, immediately perform the following.- Remove the plug from the AC outlet.- Turn this device off

• If the device becomes broken, be careful to avoid injury on broken or exposed parts.

• Do not look directly at the light emitted from the pulse sensor.

• This product includes a vibration function

CAUTION

• Do not leave this device or its accessories on an unstable or sloping surface.

• Children using this device or its accessories should be instructed in their proper operation and supervised by an adult.

• Do not use the device if it is damaged.

• If part of the device is accidentally broken, do not allow any leaking liquid to contact eyes or skin.

- Doing so may cause eye or skin complications. If the liquid gets into your eyes or mouth, rinse with clean water and consult a doctor immediately.

• Using this device may cause itching, rashes, eczema or other symptoms, depending on the user's physical condition. If skin problems occur, stop using this device immediately and consult a doctor.

• Magnets generate magnetic fields that can damage items or cause technical malfunctions.

• Data on magnetic data storage devices (e.g. credit cards, EC cards or other magnetic stripe cards) might be erased.

• The operation of pacemakers can be impaired.

• Measuring instruments may be affected.

• Keep this device away from items that are sensitive to magnetic fields.

• Observe the safety distances recommended by the manufacturers. For details, refer to the manufacturer’s instructions.

Important notes

8 Fujitsu

Travelling with your device

Transporting the device Protect the device from severe shocks and extreme temperatures (e.g., direct sunlight in a car).

► Switch off the device.

► Unplug the AC adapter and all external devices from the power socket.

► Disconnect the AC adapter cable and the data cables for all external devices.

► To protect against damaging jolts and bumps, use a case to transport your device.

Cleaning the device Do not clean any interior parts yourself; leave this job to a service technician.

Only use cleaning products designed for computers. Normal household cleaners and polishes can damage the markings the paintwork or the device itself.

Please ensure that no liquid enters the device.

► Switch the device off.

First-time setup of your device

Fujitsu 9

First-time setup of your device Please read the chapter "Important notes", Page 5.

Unpacking and checking the device Should you discover any damage that occurred during transportation, notify your local sales outlet immediately!

► Unpack all the individual parts.

► Check your device for any visible damage which may have occurred during transportation.

You may need the packaging in the future, if you need to transport your device.

Selecting a location S

Select a suitable location for the device before setting it up. Follow the instructions below when doing so:

• Never place the device or the AC adapter on a heat-sensitive surface. The surface could be damaged as a result.

• Never place the device on a soft surface (e.g. carpeting, upholstered furniture, bed). This can result in damage caused by overheating.

• The underside of the device heats up during normal operation. Prolonged contact with the skin may become unpleasant or even result in burns.

• Place the device on a stable, flat, non-slippery surface. Please note that the rubber feet of the device may mark certain types of delicate surfaces.

• Do not expose the device to extreme environmental conditions. Protect the device against dust, moisture and heat.

Using the device

10 Fujitsu

Using the device Switching the device on

►Press the power button for 3-5 seconds to switch the device on.

→ The notification LED flashes green twice

Switching the device off ►Press the power button for 5 to 9 seconds to switch the device off.

→ The notification LED flashes green 3 times

Forced shut down ► Keep the power button pressed for at least 10 seconds.

→ The device will shut down. You can then restart it.

Power Button

Using the device

Fujitsu 11

Notification LED SNyomtifibcoalstionLEDs

The notification LED provides information about the status of the power supply, battery and other notifications in the chart below.

Status Action Displays Description Flashes green twice

Powered on

Power on

Hold the power button down (at least 3-5 seconds)

Flashes green twice, then flashes red once

If the battery is too low, the device will automatically turn off. Be sure to charge it before use

Power off Hold the power button down (5 to 9 seconds)

Flashes green 3 times

Powered off

Flashes green 3 times

There is enough battery power left. Remaining battery check

Press the power button for 1 second Flashes red 3

times The battery is very low (less than 20%). Be sure to charge it before use

Charging Stays lit red Stays lit while charging, then the LED turns off when charging is complete.

Charging error －

Flashes red There is a charging error or hardware failure

Flashes green

for a maximum

of 30 seconds

Waiting for pairing. Once pairing is complete

the LED will stay on for 3 seconds

Pairing

Hold the power

button down (3 to

4 seconds) Green for 3

seconds

Pairing successful

Notification LED

Using the device

12 Fujitsu

Status Action Displays Description

300 long red

flashes

(approx.. 5

mins)

Fall / fall over alert detected

Alert detection －

10 long red

flashes All other alert notification detected

Fall alert

deactivation

Press the power

button for 1

second

Alarm is turned

off

When the power button is pressed for 1

second an alert notification of a fall

detection will be cancelled by sending a

cancellation message to the gateway

Updating

Configuration － Stays lit Orange

The configuration within the Vital

Sensing Unit L is being updated

The device takes approx. 30 seconds to start after the power is turned on. Do not press any buttons at this time

Flash = every 0.5 seconds Long Flash =every 1 second

Default Alert Status (LED/Vibration) In order to use utilize the features below you will require the “UBIQUITOUSWARE Sensor Algorithm”

Function Configuration Status indication LED

Body temperature & environment

alarm Default Off 10 long red flashes

Fall detection Default Off 300 long red flashes

(approx. 5 mins)

Fall detection

(2 m above ground) Default Off

300 long red flashes

(approx. 5 mins)

Geo-fence Default Off 10 long red flashes

Remaining battery less than 20% Default ON Flashes red 3 times

Using the device

Fujitsu 13

Upgrading the firmware You can find information on this subject on our website (“http://support.ts.fujitsu.com“)

Using the device

14 Fujitsu

Assembling the attachment (Options)

Surface fixture attachment Ports and controls

Mounting the main unit onto the flat sarface attachment ►Press the attachment shaft with a thin object (such as a ballpoint pen) to open the cap.

►Insert the main unit into the holder.

<Main unit orientation>

The main unit should be oriented so that the power button is

accessible.

Hinged Cap

Screw fixing holes

(2 locations)

10cm

Shaft <Fixing to a level surface>

Use screws 0.15 in. in diameter or (⌀ 3.8) to fix in place.(Screws are not included)

When installing ensure there is at least a 4 in. or 10 cm of free space around the hinged cap.

Using the device

Fujitsu 15

► Return the hinged cap to its original position.

To remove the attachment, open the hinged cap using the procedure from step 2 above.

Pipe attachment Ports and controls

• Pipe fixture • Pipe fixture with nuts

• Holder

• 1.75 in. or 45mm screws x4 (per set)

• Spacers x2 (per set)

• Tapping screw

•Cusions x4 (per set)

Attached to release paper

Semicircle groove Square groove This has the same shape as the pipe fixture, but includes nuts in the screw holes.

Using the device

16 Fujitsu

Mounting the pipe fixture attachment Install the holder cap in a location where it can be installed in a direction at least 4 ins. or 10 cm from nearby objects.

1 Use a caliper or other tool to measure the thickness (outer diameter) of the pipe.

2 Follow the instructions in “Joining the attachments according to the thickness of the pipe” on theother side of this sheet to join the attachments to different pipe thicknesses.

3 Peel the cushions from the paper backing and attach them to the grooves, aligned with thedirection of the pipe.

• Attached to semicircle groove • Attached to square groove

4 Use a tapping screw to attach the holder to the pipe fixture.

The holder can be installed vertically or horizontally.

Temporarily fix the holder in place with the tapping screw, adjust so that the screw holes on the

holder and pipe fixture are lined up, and then screw tightly in place.

The tapping screw can be left in after installation.

Adjust so that the lower screw

is lined up.

Using the device

Fujitsu 17

Join the pipe fixture and pipe fixture with nuts around the pipe according to the method chosen in step 2, then screw in the four 1.75 in. or 45 mm screws.

Leave a gap of around 0.12 in. or 3 mm between the pipe fixture and pipe

fixture with nuts.

6 If the method chosen in step 2 requires spacers, insert the spacers into the gap.

7 Screw the four 1.75 in. or 45 mm screws in tightly and fix the fixture to the pipe.

Do not screw the pieces together completely. Leave a gap of around

0.12 in. 3 mm between them.

(1)

(2)

(1) Insert the spacers from the top, and fit the keyed portion around the 1.75 in. or 45 mm screw.

(2) Insert the spacer toward the inside.

Using the device

18 Fujitsu

8 Mount the Location Unit (L) to the holder.

Refer to “Precautions for use” included with the Location Unit (L) for mounting instructions.

Using the device

Fujitsu 19

Joining the attachments according to the thickness of the pipe (1) Pipe thickness: 6 to 7 in. or φ15.5 to φ18

Align the semicircle grooves on the pipe fixture. Now secure the fixture using nuts to the pipe. (Do not use spacers).

(2) Pipe thickness: 7 to 8 in. or φ18 to φ20.5

Align the semicircle grooves on the pipe

fixture. Now secure the fixture using nuts to the pipe. (Use spacers)..

(3) Pipe thickness: 8 to 9 in. or φ20.5 to φ23

Align the semicircle and square grooves on the pipe fixture. Now secure the fixture using nuts to the pipe. (Do not use spacers)

(4) Pipe thickness: 9 to 10 in. or φ23 to φ25.5

Align the semicircle and square grooves on the pipe fixture. Now secure the fixture using nuts to the pipe. (Do not use spacers )

Semicircle groove

Spacer

Semicircle groove

Spacer

Semicircle groove

Square groove

Semicircle groove

Square groove

Using the device

20 Fujitsu

(5) Pipe thickness: 10 to 11 in. or φ25.5 to φ28

Align the square grooves with the pipe fixture and secure using nuts to the pipe.

(Do not use spacers)

(5) Pipe thickness: 11 to 12 in. or φ28 to φ30.5

Align the square grooves with the pipe fixture and secure using nuts to the pipe. (Use spacers)

Square groove

Square groove

Using the device

Fujitsu 21

Charging and maintaining the battery The device battery can only be charged when the ambient temperature is between 5°C / 41 °F and max. 35°C / 95°F.

If the voltage of the internal battery is abnormal, a charging error will occur and the status indication LED on the main unit will flash red. Remove the main unit from the charging cradle, then try charging again using the correct procedure. If you are still unable to charge the battery, turn the main unit off and consult with the source the product was obtained from.

Battery

Cradle charger kit (for 1 device) components

Front Rear

Above AC adapter

microUSB port

Connect the USB cable here.

Lock area

Interlocks with the main unit.

USB cable

Charging port AC adapter unit

Using the device

22 Fujitsu

Setting up the cradle Select a suitable location for the cradle before setting it up. Follow the instructions below when doing so:

• Place the cradle on a flat, stable, non slippery surface.• Never place the cradle and the AC adapter on a heat-sensitive surface.• Do not expose the cradle to extreme environmental conditions.• Protect the cradle from dust, humidity and heat.

The Vital Sensing Unit, Location Unit (S), and Location Unit (L) each require a separate charging cradle. Do not insert main units into the wrong cradle.

for Vital Sensing Unit

There is a depression behind the charging terminal.

for Location Unit (S)

There is no depression behind the charging terminal, and the inside width is narrow.

for Location Unit (L)

There is no depression behind the charging terminal, and the inside width is wide.

Using the device

Fujitsu 23

Cradle charger connecting Observe the safety notes in the enclosed "Safety/Regulations" manual.

The supplied cable conforms to the requirements of the country in which you purchased your device. Make sure that the power cable is approved for use in the country in which you intend to use it.

► Connect the USB cable to the USB connector on the AC adapter.

► Connect USB cable to the rear of the charging cradle.

► Connect the AC adapter to the power outlet.

► Remove the main unit from the attachment.

► Insert the main unit into the charging cradle.

Align the front surfaces of the main unit and charging cradle, and then insert the main unit until it locks into place.

When charging starts the main unit status indicator LED turns red.

► When charging is complete and the main unit status indicator LED turns off, remove the main unitfrom the charging cradle.

<Main unit orientation>

The main unit should be oriented so that the power button is accessible.

Troubleshooting and tips

24 Fujitsu

Troubleshooting and tips F

Follow the safety notes in the "Safety/Regulations" manual when connecting or disconnecting cables.

If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows:

► Make a note of the steps and the circumstances that led to the fault.

► Switch the device off.

► Please contact the Hotline/Service Desk.

You can find the telephone numbers in the service desk list. Please have the following information ready when you call:

• The model name and serial number of the device. The serial number is located on asticker on the underside of the device.

• Any changes you have made to the hardware or software after receiving the device.

• Your system configuration and all peripheral devices connected to your system.

• Your sales contract.

Manufacturer’s notes

Fujitsu 25

Manufacturer’s notesDisposal and recyclingNotes

You can find information on this subject on your device or on our website("http://solutions.us.fujitsu.com/www/content/products/trade-in_program/").

Recycling your batteryOver time, the batteries that run your mobile computer will begin to hold a charge for ashorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a brand new one*. If you replace it, it is importantthat you dispose of the old battery properly because batteries contain materials thatcould cause environmental damage if disposed of improperly.

Fujitsu is very concerned with environmental protection, and has enlisted the services of the Rechargeable Battery Recycling Corporation (RBRC)**, a nonprofit public service organization dedicated to protecting our environment by recycling old batteries at no cost to you.

RBRC has drop-off points at many convenient locations throughout the United States and Canada. To find the location nearest you, go to "www.RBRC.org" or call 1-800-822-8837.

If there are no convenient RBRC locations near you, you can also go to the EIA Consumer Education Initiative website "http://EIAE.org/ " and search for a convenient disposal location.

Remember – protecting the environment is a cooperative effort, and you should make every effort to protect it for current and future generations.

* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping siteat "www.shopfujitsu.com" in the US.

** RBRC is an independent third party to which Fujitsu provides funding forbattery recycling; RBRC is in no way affiliated with Fujitsu.

Manufacturer’s notes

Fujitsu 26

UL NoticeIMPORTANT SAFETY INSTRUCTIONSThis unit requires an AC adapter to operate. Only use UL Listed I.T.E. adapters with an output ratingof 19 VDC, with a minimum current of 3.42 A (65 W). The correct output rating is indicated on theAC adapter label. Refer to the illustration below for the correct AC Adapter output polarity:

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

• Do not use this product near water, for example near a bathtub, washbowl, kitchensink or laundry tub, in a wet basement or near a swimming pool.

• Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in afire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONSFor Authorized Repair Technicians Only

CAUTION:For continued protection against risk of fire, replace only with thesame type and rating fuse.

WARNING:Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace onlywith the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instruction.

Declarations of Conformity

Fujitsu 27

Declarations of Conformity

DECLARATION OF CONFORMITYaccording to FCC Part 15

Responsible Party Name: Address:

Telephone:Declares thaDeclares that product:

Fujitsu America, Inc.1250 E. Arques AvenueSunnyvale, CA 94085(408) 746-6000

Base Model Configuration: UBIQUITOUSWARE Location Unit L Complies with Part 15 of the FCC Rules.

This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.