Fuel Tank Sealer

Stops Rust, Corrosion & Leaks

• Seals Pinholes & Seams

• Bonds & Seals with a Light Grey Non-Porous Flexible Film

• Resistant to all Fuels, Alcohols & Additives

POR-15® Fuel Tank Sealer was formulated and developed in our own laboratories due to the demand for a high-tech sealer impervious to all fuels, including the new Stage II fuels which have a high alcohol content. POR-15® Fuel Tank Sealer has superior strength and fuel resistance, and does not contain Methyl Ethyl Ketone, a highly flammable and deadly carcinogen (cancer-causing). POR-15® Fuel Tank Sealer is non-flammable and is environmentally safe.

PRODUCT SIZE CODE

Fuel Tank Sealer Gal. 49201

Fuel Tank Sealer Qt. 49204

Fuel Tank Sealer Pt. 49208

Fuel Tank Sealer 8 oz. 49216

Features:• Resistant to all fuels, alcohol,

additives & solvents

• Stops rust, corrosion & leaks permanently

• Seals pinholes & seams - POR-15® TOUGH!

• Chemically bonds to metal surfaces (even rusted)

• Permanently flexible

• Light gray color for easier viewing inside the tank

• Available in quarts (capable of sealing a 25 gal. tank)

Product Information

800-457-6715PORproducts.com

© 2018 P.O.R. Products ® POR-15 is a registered trademark of P.O.R. Products.

P.O.R. Products, 38 Portman Rd, New Rochelle, NY 10801

Fuel Tank Sealer

Stops Rust, Corrosion & Leaks

Product Description

POR-15 Fuel Tank Sealer is a high-tech sealer impervious to all fuels, including the new Stage II fuels which have a higher alcohol content. It has superior strength and fuel resistance.

Application Information

Drain all fuel from tank, remove tank from vehicle, and clean out tank. All fuel tanks are dirty and have to be cleaned out before sealing. DO NOT MIX THIS SEALER WITH ANY FUELS. If you try to seal a tank without cleaning it first, the new coating will fail, because Tank Sealer won’t stick to gum and varnish. Mix 1 part of POR-15® Cleaner Degreaser with 1 part of hot water and pour into tank. Gloves and eye protection should be worn at all times. Roll the tank around, then place in different position every 2 hours so the solution can cover all inside surfaces. Repeat this step until solution comes out clean then rinse tank thoroughly with water 2 or 3 times to remove all the cleaner then permit to dry. Next pour in full container of POR-15® Metal Prep and roll the tank around, then place the tank in different positions every half hour until the entire inside of the tank has been treated with POR-15® Metal Prep. Then rinse the tank thoroughly with hot water several times, then drain and dry completely with a hair dryer or heat gun. Tank must be bone dry before you can use Fuel Tank Sealer. Remove valves, petcocks, floats, feed lines, filters, and other mechanisms. Sealer will clog narrow feed lines if they are not sealed off. If lines get clogged, they can be cleared with a wire or coat hanger before sealer is dry. Plug all open holes with duct tape, cork, or rubber stopper except main filler hole. Tank must be completely dry inside. Ideal working temperature is 72°F. STIR WELL BEFORE USING. Pour entire contents of Tank Sealer into tank, cover fill hole, then slowly rotate tank back and forth, side to side, and upside down to cover all surface and seams. Then drain for at least 30 minutes to ensure that Tank Sealer has not puddled in tank. Allow 96 hours for drying. Air-dry tank in well ventilated area, drying time can be improved by using a low pressure blower or hair dryer (low or no heat) and circulating it through one hole in tank and out another. DO NOT REUSE SEALER. Let remnant drained sealer dry out in open can, then discard in accordance with local regulations.

Safety Information

WARNING: Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes nose, throat, skin and eye irritation. Harmful if swallowed. NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and central nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.

NOTICE: INDIVIDUALS WITH LUNG OR BREATHING PROBLEMS OR PRIOR REACTION TO ISOCYANATES MUST NOT BE EXPOSED TO VAPOR OR SPRAY MIST. Do not breathe vapor or spray mist. Ensure fresh air entry during application and drying. Open windows and doors or use other means to ensure fresh air entry during

application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH-approved) during and after application. [An airline respirator (NIOSH-approved) is recommended. A vapor/particulate matter respirator (NIOSH-approved) may be appropriate where airborne monitoring demonstrates vapor levels below ten times the applicable exposure limits.] Follow respirator manufacturer’s direction for respirator use.

Keep container tightly closed when not in use. Keep away from heat, sparks, open flame, hot surfaces or other ignition sources. Do Not Smoke. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. In case of fire, use CO2, dry chemical or foam to extinguish. Avoid contact with eyes, skin and clothing. Do not get in eyes, on skin or clothing. Wash thoroughly after handling.

FIRST AID: FOR INHALATION: If you experience difficulty breathing, leave area to obtain fresh air. If continued breathing difficulty is experienced, get medical attention immediately. IF SWALLOWED: DO NOT induce vomiting; immediately call Poison Control Center and have label available. FOR SKIN CONTACT: Wash thoroughly with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if skin irritation occurs or you feel unwell. FOR EYE CONTACT: Flush eyes immediately with plenty of fresh water. Remove contact lenses if possible. Continue eye flushing with water for at least 15 minutes and get medical attention immediately.

A WARNING: This product can expose you to chemicals including Cumene, which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

CLEAN UP: Use POR-15® Solvent for clean-up, which must be done before POR-15® Fuel Tank Sealer dries; once dry POR-15® Fuel Tank Sealer cannot be removed by solvent.

For skin protection wear protective clothing and gloves; for eye protection wear safety glasses with side shields or splash-proof goggles. Avoid skin contact. Remove from skin at once to avoid temporary staining. Moisture will shorten the life of unused POR-15® Fuel Tank Sealer; seal can immediately after dispensing. Transport and Store Upright Only and never in an area of sun or heat exposure.

WARNING: If you scrape, sand, or remove old paint, you may release lead dust. LEAD DUST IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

Refer to Material Safety Data Sheet available upon request for further safety and handling information.