Front View - NEVCO · WHP 8/16/2017 241-0388 1 1 Bracket Orientation Front View Screw Multisection...
Transcript of Front View - NEVCO · WHP 8/16/2017 241-0388 1 1 Bracket Orientation Front View Screw Multisection...
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc.
Greenville, Illinois 62246
Installationof Aluminum
Trusseson Two Columns
WHP 8/16/2017
241-0388
1 1
Bracket Orientation
Front View
Screw MultisectionTruss together withscrews in bag tapedto splice connection.
This truss is rated at 150 mph when mounted to columns at factory manufactured mounting locations. Mounting Trusses to columns in any other configuration can affectthe integrity of the sign.
(d)
(c)
(e)
(a)
(b)
Variation ChartTruss Width (a) Truss Height (b) Bracket Height (c) Bracket Height (d) Column Width (e) Est Weight
18' 3' 28 13/32'' 3 7/32" 10' 145
16' 3.7' 34 1/2" 2" 8' 136
18' 4' 37 1/8" 2" 10' 16512' 2' 6" 18 11/16" 2" 8' 9010' 2' 6" 18 7/8" 2" 8' 648' 2' 6" 18 7/8" 2" 6' 5814' 2' 18 1/8" 2" 8' 78
11.02' 2' 6" 20 3/4" 2" 8' 7716' 4' 40" 2" 8' 136
B
(4) 3/8" serrated flangebolts supplied by Nevcoto attach brackets to truss
4 1/8 in
6 5/8 in *
* Dimension shown is typical. Slots in brackets allow for approximately ½" variation.
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
Installation of Aluminum Truss onThree Columns
BRS 12/4/2017
241-0390
1 2
EFront View
Bracket Orientation
This truss is rated at 150 mph whenmounted to columns at factory manufacturedmounting locations. Mounting trusses tocolumns in any other configuration can affectthe integrity of the truss.
Bolt bracket to trussusing four 3/8 inch serrated flange bolts supplied by Nevco
Variation ChartTruss Width (a) Truss Height (b) Bracket Height (c) Bracket Height (d) Column Spacing (e) Est Weight
28' 4' 38" 43 1/2" 120" 257
24' 4' 32 1/4" 42 7/8" 96" 220
24' 3' 19 15/16" 30 15/32" 96" 18520' 4' 25 5/8" 44 3/4" 108" 110
(a)
(e) (e)
(b)
2 in
(c)
(d)
Screw truss sectionstogether using screwsin bag taped to spliceconnection (front andback of truss). Use screws wherever possible.
4 in6 1/2 in*
* Dimension shown is typical. Slots in brackets allow for approximately ½" variation.
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
A
Installation of Aluminum Truss onThree Columns
BRS 2 2
241-0390
This sheet refers to the truss installedon two columns using laterals
Position laterals so that theysupport the outer brackets as shown
Weld riser and mountingsection to upper lateral
Side View(dimensions from
Sheet 1)
Front View
5 1/4 in
(c)
(d) - (c)
Individual brackets are 12" wide and arecentered on the columns (e) on sheet 1. Example: 3 columns spaced 10' apart plus12" for the bracket would require a lateralthat is 21' long.
E
12/4/2017
4 in4 5/8 in
typical
Dimension of lateral will vary
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
Installation of AluminumTrusses on
Four Columns
BRS 7/12/2017 1 2
B
Attach brackets totruss using four3/8" serrated flangebolts supplied by Nevco
(a)
(e) (e) (e)
2 in
(c)
(d)
Variation Chart
Truss Width (a) Truss Height (b) Bracket Height (c) Bracket Height (d) Column Spacing (e) Est Weight
32' 4' 32 1/4" 42 7/8" 8' 294
36' 4' 15 1/2" 39 9/16" 10' 33140' 4' 28 7/8" 41 1/8" 10' 367
This truss is rated at 150 mph whenmounted to the columns at factorymanufactured mounting locations.Mounting trusses to columns inany other configuration can affectthe integrity of the sign.
Screw truss sections togetherusing screws in a bag taped tothe splice connection - Use screwswherever possible along seam onboth front and back.
241-0394
4 in6 1/2 in*
* Dimension shown is typical. Slots in brackets allow for approximately ½" variation.
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Drawn Date
Drawing No.
Sheet of
Rev
Nevco, Inc. Greenville, Illinois 62246
Installation ofAluminum Truss on
Four Columns
BRS 7/12/2017 2 2
241-0394
This sheet refers to the truss installedon three columns using laterals
Front View
Side View(dimensions from
sheet 1)
Position laterals so that theysupport the outer bracketsas shown
Weld risers and mountinglateral in these places
Weld to center column
2 in
(c)
(d) - (c)
Individual brackets are 12" wide and are centered on the columns (e) on sheet 1. Example: 4 columns spaced 8' apart plus12" for the bracket would require a lateralthat is 25' long.
B
4 in
Dimension of lateral will vary
4 5/8 in
typical