Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve...
-
Upload
griffin-wakeland -
Category
Documents
-
view
227 -
download
0
Transcript of Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve...
![Page 1: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/1.jpg)
Four Stroke SI Engine
Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressedStroke 3: Combustion (~constant volume) occurs and product gases expand doing workStroke 4: Product gases pushed out of the cylinder through the exhaust valve
CompressionStroke
PowerStroke
ExhaustStroke
A I R
CombustionProducts
Ignition
IntakeStroke
FUEL
Fuel/AirMixture
![Page 2: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/2.jpg)
Crank shaft
90o
180o
BC
TC0o
270o
Spark plug for SI engineFuel injector for CI engine
Top Center(TC)
BottomCenter(BC)
Valves
Clearancevolume
Cylinder wall
Piston
Stroke
CylinderComponents
![Page 3: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/3.jpg)
IVO - intake valve opens, IVC – intake valve closesEVO – exhaust valve opens, EVC – exhaust valve opensXb – burned gas mole fraction
Four-Stroke SI Engine
Exhaust gas residual
![Page 4: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/4.jpg)
Two Stroke SI Engine
Intake (“Scavenging”)
Compression Ignition
ExhaustExpansion
Fuel-air-oilmixture
Fuel-air-oilmixture compressed
Crankshaft
Checkvalve
Exhaustport
![Page 5: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/5.jpg)
Cross Loop Uniflow
Two-Stroke Scavenging
![Page 6: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/6.jpg)
EPO – exhaust port open EPC – exhaust port closedIPO – intake port openIPC – intake port closed
Exhaust area
Intake area
Two-Stroke SI Engine
scavenging
![Page 7: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/7.jpg)
Cylinder Arrangement
Single-cylinder engine gives one power stroke per crank revolution (2 stroke) or two revolutions (4 stroke). The torque pulses are widely spaced, and engine vibration and smoothness are significant problems.Used in small engine applications where engine size is more important Multi-cylinder engines spread out the displacement volume amongst multiple smaller cylinders. Increased frequency of power strokes produces smoother torque characteristics. Engine balance (inertia forcesassociated with accelerating and decelerating piston) better than singlecylinder.
Most common cylinder arrangements:- In-line 4-cylinder- In-line 6-cylinder- V-6 and V-8
![Page 8: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/8.jpg)
Power Regulation (Throttling)
An IC engine is basically an air engine, the more air you get into thecylinder, the more fuel you can burn, the more power you get out.The initial pressure in the cylinder is roughly equal to the pressurein the intake manifold.
Pressure in the intake manifold is varied by opening and closing thethrottle plate to change the pressure drop. Maximum air flow (andpower) achieved at wide-open-throttle (WOT). Minimum air flow at idle
PatmPint < Patm
Intake manifold
Fuel
WOT
Idle
![Page 9: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/9.jpg)
Basic Carburetor Design
Venturi
Throttle
Air Flow
Mixture to manifold
Fuel
![Page 10: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/10.jpg)
Fuel Injection System
Throttle
Fuel tank
Air intakemanifold
During start-up the components are cold so fuel evaporation is very slow, as a resultadditional fuel is added through a second injecting valve
![Page 11: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/11.jpg)
Superchargers are compressors that are mechanically driven by theengine crankshaft and thus represent a parasitic load.
Compressor
Patm
Pint > Patm
![Page 12: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/12.jpg)
Turbochargers couple a compressor with a turbine driven by the exhaust gas. The compressor pressure is proportional to the engine speed
![Page 13: Four Stroke SI Engine Stroke 1: Fuel-air mixture introduced into cylinder through intake valve Stroke 2: Fuel-air mixture compressed Stroke 3: Combustion.](https://reader030.fdocuments.net/reader030/viewer/2022032701/56649c915503460f9494c4f2/html5/thumbnails/13.jpg)
The peak pressure in the exhaust system is only slightly greater than atmospheric – small P across turbine.
In order to produce enough power to run compressor the turbine speed must be very fast (100k-200k rev/min). It takes time for the turbine toget up to speed so when the throttle is opened suddenly there is a delayin achieving peak power - Turbo lag.
Waste gate valve controls the exhaust gas flow rate to the turbine.It is controlled by the intake manifold pressure
INTAKEAIR
EXHAUSTFLOW