FORMULA 6-P
-
Upload
john-singh -
Category
Documents
-
view
217 -
download
0
description
Transcript of FORMULA 6-P
ENGLISH Revision 07/08/2002 (Check www.thermbond.com for updates)
Bag Weight* 43 lbs 19.5 kg 1500F (816C) 4000 psi 281 kg/cm2 28 N/mm2 Jug Weight* 8 lbs 3.6 kg 2000F (1093C) 8000 psi 562 kg/cm2 55 N/mm2
Drum Weight* 400 lbs 181.4 kg 2500F (1371C) 11750 psi 826 kg/cm2 81 N/mm2 Unit Weight* 51 lbs 23.0 kg
Yield / Unit* 0.34 ft3 0.010 m3
Units / Ton* 39.53 short 35.86 metric 1500F (816C) Unit Equivalent 2000F (1093C)
Board Feet / Unit* bd ft 2500F (1371C) Wet to Dry Ratio*
Liquid Activator Bags Per Pallet Al2O3
Drums Per Dry Pallet SiO2 Fe2O3 P2O5
Data based on Other Alternative Method*** Total
As Placed 148 lbs/ft3 2371 kg/m3 600F (316C) 8.5 1.23 W/m KAfter 1500F (816C) 140 lbs/ft3 2243 kg/m3 1200F (649C) 9.1 1.31 W/m K
1800F (982C) 9.5 1.37 W/m K2400F (1316C) 10.1 1.45 W/m K
Hot Face 3000 F 1649 C
1500F (816C) 900 psi 63.28 kg/cm2 6 N/mm22000F (1093C) 1750 psi 123.04 kg/cm2 12 N/mm2
After 1500F (816C) <20 2500F (1371C) 2600 psi 182.80 kg/cm2 18 N/mm2
1500F (816C) 2100 psi 148 kg/cm2 14 N/mm2
9.85%100.00%
23.61%
Casting
0.92%1
58.81%
ABRASION RESISTANCE** (ASTM C-704)
Btu-in/hr-ft2-F
17.7% - 19.4%
48
BULK DENSITY**
Hand Packing Troweling
APPLICATION***
TYPICAL CHEMICAL ANALYSIS (After 1500F (816C))**
MAXIMUM RECOMMENDED SERVICE TEMP**
Due to the unique nature of the Stellar binder system, test procedures vary slightly from ASTM. Documentation of these variations is available upon request.
***Application by alternative method may produce somewhat different results.
cc loss
HOT MODULUS OF RUPTURE**
*Measures are approximate and may vary. For mixing partial units, contact Stellar Materials for specific wet-to-dry ratios. See Installation Guide for more detailed information.
**Test data shown are based on averages subject to normal variation on individual tests, and therefore should not be assumed to be maximum or minimum specifications.
0.03%
Btu-in/hr-ft2-F
FORMULA 6-PFormerly Formula Patch
Unlike any other refractory, Thermbond incorporates the unique two-part Stellar Binder System, providing super fast setting, super fast curing, tenacious bonding, and other unique features. CHARACTERISTICS: - Alumina - Silica -
Mullite - Dense - Fine Grain - Non-Wetting - Fast Setting - Fast Curing -
PACKAGING COMPRESSIVE STRENGTH**
PERMANENT LINEAR CHANGE**
4.1
FORMULA
0.07%0.06%
COLD MODULUS OF RUPTURE**
Bags: 1 Jugs: 1
Btu-in/hr-ft2-FBtu-in/hr-ft2-F
THERMAL CONDUCTIVITY**
6.82%