Keith Hitchins Romania intre 1866 1947 (de la primul razboi mondial)
FORMCEAL 3000X - Hitchins
Transcript of FORMCEAL 3000X - Hitchins
FORMCEAL 3000XWATERPROOFING SYSTEM
FORMCEAL 3000XWATERPROOFING SYSTEM
FORMCEAL 3000X IS A SELF-ADHESIVE
BITUMINOUS MEMBRANE OBTAINED
BY THE HOT LAMINATION OF A
MODIFIED BITUMEN COMPOUND
WITH A CROSS LAMINATED HIGH-
DENSITY POLYETHYLENE FILM (HDPE).
COMPOSITION
AREAS OF USAGE
AUDI CENTRE - SINGAPORE
and physical characteristics, such as shape stability and high strength, as well as a limited although uniform, thermal deformation.
FORMCEAL 3000X is made from two structural components:
Bitumen Compound
tack resins. This special compound has been formulated, improved and adapted to attain controlled adhesion, allowing easy installation, without immediately sticking fast to the
few minutes and this allows FORMCEAL 3000X to be repositioned if necessary.
HDPE Protective Film
FORMCEAL 3000X its mechanical and physical characteristics, such as heat stability, shape stability and chemical resistance.
accidental damage of the membrane by enabling the black
ASTM C1549-09.
“”
The result is a
““performance as demanded by today’s
advanced building
”” technology.
• Foundations • Tunnels and other below grade structures • Ramps • Car parks • Flat roofs • Ground slabs
040-034Low Emission
Low ToxicityAdhesive Sealant
SPECIAL FEATURES
Completely Watertight Able to resist high hydrostatic water pressure.
Cold & Easy Application
system. Adapts easily to irregular shaped surfaces.
Chemical Resistance
pollutants.
Self Sealing Able to self-seal on contact, if installed using nails or other fasteners or even if cut accidentally.
Signal Layer
Constant Thickness Manufactured using high technology machinery, which constantly monitors their thickness.
“”
“performance as demanded by today’s
” technology.
WARRANTY INFORMATION Only Hitchins’ trained applicators are approved to undertake all application work. Hitchins products carry a long-term warranty for both materials and workmanship. The warranty is further backed by Hitchins International Fidelity Fund. Please check with our local applicators if
FORMCEAL 3000XWATERPROOFING SYSTEM
DATA SPECIFICATION SHEET
DESCRIPTION
“performance as demanded by today’s
” technology.
ASIA’S LEADING
BUILDING PROTECTION
SPECIALIST
Formceal 3000X is a self adhesive bituminous/asphalt membrane for all types of
properties such as high resistance to acids, alkalies and pollutants.
C1549-09.
Formceal 3000X exhibits a self sealing action if it is punctured by nails or accidentally cut, the membrane will re-seal on contact and maintaining water tight.
PRODUCT SPECIFICATION
COLOUR: Grey or Black
ROLL SIZE: 20m long by 1m wide
AVAILABILITY: Available as individual rolls or in pallets of 15 rolls
NOMINAL THICKNESS (UNI 8202): 1.5mm
TENSILE STRENGTH (ASTM D638): 5.03 N/mm2
ELONGATION (ASTM D638): 832%
PUNCTURE RESISTANCE (ASTM E154): 906N
RESISTANCE TO HYDROSTATIC PRESSURE (ASTM D5835): 70m
PLIABILITY (SS374): No surface rupture
RESISTANCE TO LEAKAGE AT JOINTS (SS374): No leakage
TENSILE SHEAR AT JOINTS (SS 374): Failure occur outside the joint
WATER VAPOUR TRANSMISSION (SS374): 0.02g/m2/hr
WATER ABSORPTION (SS374): 0.08%
SOLUABLE MATTER (SS374): 0.03%
SOLAR REFLECTANCE (ASTM C1549-09):
040-034Low Emission
Low ToxicityAdhesive Sealant
SUBSTRATE APPLICATION
Prime the substrate with Formceal Primer or a suitable bituminous primer by brush or roller at 4m2/l and allow to dry.
Unroll membrane. Ensure that there is an overlap of 100mm at the ends and 60 mm at the sides.
For application on horizontal substrates, remove about 400mm of the release paper and position the membrane on the area to be waterproofed and press down. By pulling on the free end of the release paper, the membrane will automatically unroll without forming wrinkles or folds. When the membrane is correctly aligned press it into position.
For ease of handling on vertical substrates, cut the Formceal 3000X into lengths of 3m.
This membrane can be covered with either a concrete screed or topping, tiles, aggregate, insulation material or similar. When doing so, make sure that the membrane is not punctured or damaged.
HEALTH & SAFETY
spills. Dry paint can be removed from the skin with soap and warm water.
Revision BAll data given and statements and recommendations made herein are base upon our research and experience and are
all other issues.
Place Product
Sample HereHitchins (FE) Marketing Pte Ltd
Telephone: (65) 6861 1177Facsimile: (65) 6863 4240
Email: [email protected]
AREAS OF USAGE
such as roofs, decks, patios, insulated roofs, inverted roofs, bridges and viaducts, foundation and retaining walls etc.
No heat is needed during installation. Formceal 3000X ideal for application in areas
SUBSTRATE PREPARATION
Make sure that the substrate is clean, dry and free of dirt, oil etc.
MAJOR PROJECTS
APPLICATION & INSTALLATION
Echelon @ Alexandra - Singapore Great World MRT Station - Singapore Park Regis Hotel - Singapore
St Joseph Home - Singapore The Brooks I & II - Singapore Shuang Lin Temple - Singapore
Islamic Museum - KL, Malaysia Istana Melawati - Malaysia
1. Application of Bituminous Primer 2. Laying of Membrane on Slab 3. Side & End Lapping of Membrane
4. Termination at Upturn 5. Laying of Membrane on Wall 6. Completion
Multi-Purpose Hall Putrajaya - Malaysia