FORD KUGA - Towbars DirectFITTING INSTRUCTIONS 14085/F FORD KUGA • Remove any mastic from contact...
Transcript of FORD KUGA - Towbars DirectFITTING INSTRUCTIONS 14085/F FORD KUGA • Remove any mastic from contact...
-
ISTRUZIONI DI MONTAGGIOFITTING INSTRUCTIONS
INSTRUCTIONS DE MONTAGEMONTAGEANLEITUNG
INSTRUCCIONES DE MONTAJE
DISPOSITIVO DI TRAINO TIPOTOWING BRACKET TYPEDISPOTIF DE REMORQUAGE TYPEANHAENGEVORRICHTUNG TYPDISPOSITIVO DE CAREO TIPO
14085/F
PER AUTOVEICOLIFOR CARSPOUR AUTOSFUR KRAFTAHRZEUGEPARA AUTOVEHICULO
FORD KUGA
TYPE DM2 2008 =>
CLASSE E TIPO DI ATTACCOCLASS AND HITCH TYPECLASSE ET TYPE DE CROCHETKLASSE UND BEFESTIGUNGSARTCLASES DE ACOPLAMIENTO
OMOLOGAZIONEHOMOLOGATIONHOMOLOGATIONZULASSUNGAPROBACION
CARICO VERTICALE MAXS VALUEMASSE VERTICALE MAXIMUMZUL. STUETZLASTCARGA MAX. VERTICAL
F e3 00 – 7478(DIR. 94/20/CE)
S = kg 125
VALORE DD VALUEVALEUR DD WERTVALOR D
D = 11,2 kN
COPPIA DI SERRAGGIO PER VITI (8.8):TORQUE SETTINGS FOR NUTS AND BOLTS (8.8):
COUPLE DE SERRAGE POUR VIS (8.8):SCHRAUBENANZUGSMOMENT (8.8):
MOM. DE PRESION PARA TORNILLOS Y TUERCAS (8.8):
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 1 / 6
11,2 kN
M6 = 10 Nm M8 = 25 NmM10 = 55 Nm M12 = 85 NmM14 = 135 Nm M16 = 200 Nm
Tel. +39 075.5280260Fax +39 075.5287033Via Pizzoni 37/3906132 PerugiaITALY
http://www.umbrarimorchi.it/mailto:[email protected]
-
SAFETY INSTRUCTIONS
Make sure that the towbar is suitable for the vehicle before starting the installation.
For safety, all work involving towbar installation (incl. electrical components) must be undertaken by skilled technicians.
Damaged components must be replaced with manufacturer’s spares and fitted by qualified staff.
It is forbidden to make any modification or structural repair to towing assembly.
The towball must be kept clean and lubricated. For added safety, his diameter (50 mm) must be checked at regular intervals. If the towball measures less than 49 mm after selected readings across the diameter, the towball must be replaced with a new one.
After 1000 km of towing, check torque settings for nuts and bolts, in accordance with the table.
Umbra Rimorchi cannot be held responsible for any defects in the product caused by fault or by any injudicious use whatever of the user or a person he is liable for.
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 2 / 6
-
FITTING INSTRUCTIONS
14085/F FORD KUGA
• Remove any mastic from contact points and paint with anti-rust paint.
1. Remove bumper ( 4 fixing on lower edge, 1 fixing each side of boot opening, 3 around each wheel arch and fold back wheel arch liner to reveal one additinally fixing. Unplug fog lamps. Pull bumper tips out sideways and then rearwards) .
2. Remove the polystirene bars that absorb the shocks from the bumper beam 3. bar and remove towing eye.4. Remove the bumper beam. 5. Insert the two side arms A inside the two open ends of the chassis and bolt using
bolts 1.6. Locate cross bar B using holes 2 and 3 and tighten7. Fully tighten all nuts and bolts.8. Connect the wirings to the socket.9. Please pay attention:the wirings must be as far as possible from the exhaust.10. Re-fit the polystyrene bars on the cross bar and fix them with double-sided tape,
glue or silicone.11.Re-fit the towing eye and bumper.
DISAPPEARING ELECTRICAL SOCKET
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 3 / 6
-
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 4 / 6
-
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 5 / 6
-
Cod. 14085/F- Ford Kuga - v. 1.0 01/01/2011 P. 6 / 6
TYPEDM2F