Force Method for Analysis of Indeterminate Structures Number of ...
Transcript of Force Method for Analysis of Indeterminate Structures Number of ...
![Page 1: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/1.jpg)
Force Method for Analysis of Indeterminate Structures
Number of unknown Reactions or Internal forces > Number of equilibrium equationsNote: Most structures in the real world are statically indeterminate.
Smaller deflections for similar members•
Redundancy in load carrying capacity (redistribution)
•
Increased stability•
Advantages Disadvantages
More material => More Cost•
Complex connections•
Initial / Residual / Settlement Stresses•
Methods of Analysis
(i) Equilibrium of forces and moments(ii) Compatibility of deformation among members and at supports(iii) Material behavior relating stresses with strains(iv) Strain-displacement relations(v) Boundary Conditions
Structural Analysis requires that the equations governing the following physical relationships be satisfied:
Primarily two types of methods of analysis:
(Ref: Chapter 10)
Displacement (Stiffness) Method
Express local (member) force-displacement relationships in terms of unknown member displacements.
•
Using equilibrium of assembled members, find unknown displacements.
•
Unknowns are usually displacements•
Coefficients of the unknowns are "Stiffness" coefficients.
•
Convert the indeterminate structure to a determinate one by removing some unknown forces / support reactions and replacing them with (assumed) known / unit forces.
•
Using superposition, calculate the force that would be required to achieve compatibilitywith the original structure.
•
Unknowns to be solved for are usually redundant forces
•
Coefficients of the unknowns in equations to be solved are "flexibility" coefficients.
•
Force (Flexibility) Method
For determinate structures, the force method allows us to find internal forces (using equilibrium i.e. based on Statics) irrespective of the material information. Material (stress-strain) relationships are needed only to calculate deflections.
However, for indeterminate structures , Statics (equilibrium) alone is not sufficient to conduct structural analysis. Compatibility and material information are essential.
Indeterminate Structures
ForceMethod Page 1
![Page 2: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/2.jpg)
Maxwell's Theorem of Reciprocal displacements; Betti's law
Betti's Theorem
For structures with multiple degree of indeterminacy
Example:
The displacement (rotation) at a point P in a structure due a UNIT load (moment) at point Q is equal to displacement (rotation) at a point Q in a structure due a UNIT load (moment) at point P.
Virtual Work done by a system of forces PB while undergoing displacements due to system of forces PA
is equal to the Virtual Work done by the system of forces PA while undergoing displacements due to the system of forces PB
ForceMethod Page 2
![Page 3: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/3.jpg)
Force Method of Analysis for (Indeterminate) Beams and Frames
Example: Determine the reactions.
ForceMethod Page 3
![Page 4: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/4.jpg)
ForceMethod Page 4
![Page 5: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/5.jpg)
Examples
Support B settles by 1.5 in.Find the reactions and draw the Shear Force and Bending Moment Diagrams of the beam.
ForceMethod Page 5
![Page 6: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/6.jpg)
Example: Frames
ForceMethod Page 6
![Page 7: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/7.jpg)
ForceMethod Page 7
![Page 8: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/8.jpg)
Force Method of Analysis for (Indeterminate) Trusses
ForceMethod Page 8
![Page 9: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/9.jpg)
ForceMethod Page 9
![Page 10: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/10.jpg)
Force Method of Analysis for (Inderminate) Composite Structures
ForceMethod Page 10
![Page 11: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/11.jpg)
Part 1 Part 2
ForceMethod Page 11
![Page 12: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/12.jpg)
Systematic Analysis using the Force (Flexibility) Method
Note: Maxwell's Theorem (Betti's Law) => Flexibility matrix is symmetric!
Example:
ForceMethod Page 12
![Page 13: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/13.jpg)
ForceMethod Page 13
![Page 14: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/14.jpg)
ForceMethod Page 14
![Page 15: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/15.jpg)
ForceMethod Page 15
![Page 16: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/16.jpg)
Analysis of Symmetric structures
Symmetry: Structure, Boundary Conditions, and Loads are symmetric.
Anti-symmetric: Structure, Boundary Conditions are symmetric, Loads are anti-symmetric.
Symmetry helps in reducing the number of unknowns to solve for.
Examples:
ForceMethod Page 16
![Page 17: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/17.jpg)
Influence lines for Determinate structures(Ref: Chapter 6)
Influence line is a diagram that shows the variation for a particular force/moment at specific locationin a structure as a unit load moves across the entire structure.
The influence of a certain force (or moment) in a structure is given by (i.e. it is equal to) thedeflected shape of the structure in the absence of that force (or moment) and when given a corresponding unit displacement (or rotation).
Müller-Breslau Principle
Example:
Examples:
ForceMethod Page 17
![Page 18: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/18.jpg)
Draw the influence lines for the reaction and bending-moment at point C for the following beam.Example
A B C D
ForceMethod Page 18
![Page 19: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/19.jpg)
Draw the influence lines for the shear-force and bending-moment at point C for the following beam.•
Find the maximum bending moment at C due to a 400 lb load moving across the beam.•
Example
A B C D
ForceMethod Page 19
![Page 20: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/20.jpg)
Influence lines for Indeterminate structures
For statically determinate structures, influence lines are straight.For statically indeterminate structures, influence lines are usually curved.
The Müller-Breslau principle also holds for indeterminate structures.
Examples:
Reaction Ay Shear at a point: Moment at a point
ForceMethod Page 20
![Page 21: Force Method for Analysis of Indeterminate Structures Number of ...](https://reader034.fdocuments.net/reader034/viewer/2022050807/5866f0241a28ab36408b9348/html5/thumbnails/21.jpg)
Vertical reaction at A�
Moment at A�
Draw the influence line for Example
ForceMethod Page 21