For more information:www.devancocanada.com

or call toll free at 855-931-3334

INST

R,IN

ST,M

DT

SER

IES

Line

ar P

/N: 2

0777

9 D

Mat

eria

l: 20

Lb.

Mea

d Bo

ndSi

ze: 8

.500

" x 1

1.00

0"In

k: B

lack

Scal

e: 1

-1Si

de 2

of 2

STEP 5 Review memory. Press and hold the receiverʼsprogram button (channel one or two) until the LED begins to flash(about 3 seconds) and then release the button. Count the numberof flashes. The number of flashes equals the number oftransmitters programmed into that channel of the receiver.➥ NOTE: Donʼt hold down the programming button longer than

5 seconds, the receiverʼs memory for that channel will beerased (Step 7).

STEP 6 Test receiver. Be sure door area is clear. Activateeach transmitter. The receiver relay should click (relay outputmodels only) and the operator should activate. Wait 2 secondsbetween each activation.

STEP 7 Erasing receiver memory. Transmitters may beerased from the receiverʼs memory by pressing and holding thereceiverʼs program button (channel one or two) for 5 seconds ormore. After the LED blinks (count of transmitters) it will blink onemore time for channel one and twice for channel 2 as thereceiverʼs memory for that channel is erased. All transmittersfor each receiver channel are erased at the same time.

INFO 1A Opening battery compartment. To access thetransmitterʼs batteries remove the battery access screw on theback of the unit. Flip the unit over so that the front is facing you.Use a small screwdriver to open the battery compartment.

INFO 1B Replacing transmitter batteries. Replace the twobatteries with two Type 2032 lithium batteries or equivalent. Thebatteries stack on top of each other with the (+) sides facing thefront of the transmitter. Replace with new batteries then close thebattery compartment, replace battery access screw and testtransmitter.

INFO 2 Visor Clip Removal. The visor clip can be removedby removing the three screws as shown. Slide the clip off theretaining plate and reattach the plate to the transmitter.

➥ NOTE: The same transmitter (or the same transmitter button onmulti-button transmitters) cannot be programmed into bothreceiver channels 1 and 2.

➥ NOTE: If the receiverʼs LED flashes continuously when atransmitter isnʼt being activated, the receiver is too close to anelectrical noise source. Move the receiver away from the noisesource or call technical services for assistance.

LIMITED WARRANTYThis product is warranted to the consumer against defects in material andworkmanship for one year from the date of purchase. This warranty appliesto first retail buyers of new devices. Warrantor will repair, or at its option,replace, any device it finds that requires service under this warranty, andwill return the repaired or replaced device to the consumer at thewarrantorʼs cost. For warranty service and shipping instructions contactwarrantor at the address shown below. Devices must be sent to warrantorfor service at ownerʼs expense. The remedies provided by this warrantyare exclusive. Implied warranties under state law are to the one year periodof this written warranty. Some states do not allow limitations on how longan implied warranty lasts, so the above limitation may not apply to you. Inorder to be protected by this warranty, save your proof of purchase andsend copy with equipment should repair be required. This warranty givesyou specific legal rights, and you may also have other rights which varyfrom state to state.All products returned for warranty service require a Return ProductAuthorization Number (RPA#). Contact Linear Technical Services at1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!Linear radio controls provide a reliable communications link and fill animportant need in portable wireless signaling. However, there are somelimitations which must be observed.✶ For U.S. installations only: The radios are required to comply with FCC

Rules and Regulations as Part 15 devices. As such, they have limitedtransmitter power and therefore limited range.

✶ A receiver cannot respond to more than one transmitted signal at a timeand may be blocked by radio signals that occur on or near their operatingfrequencies, regardless of code settings.

✶ Changes or modifications to the device may void FCC compliance.✶ Infrequently used radio links should be tested regularly to protect against

undetected interference or fault.✶ A general knowledge of radio and its vagaries should be gained prior to

acting as a wholesale distributor or dealer, and these facts should becommunicated to the ultimate users.

Copyright © 1999 Linear Corporation 207779 D

WARNING!BE SURE DOORAREA IS CLEAROF OBSTRUCTIONS

PRESS TRANSMITTERBUTTON TO TEST

CH2CH1

CH2CH1

PRESS PROGRAM BUTTON(CHANNEL 1 OR 2)FOR FIVE SECONDS OR MORE

LED WILL FLASH, COUNTING THETOTAL NUMBER OF TRANSMITTERSPROGRAMED TO THAT CHANNEL. THEN IT WILL BLINK ONE MORE TIMEAS THE TRANSMITTERS ARE ERASEDFROM THAT CHANNEL

2032

REMOVE BATTERY ACCESS SCREW

SWING BATTERY COMPARTMENT OPEN

FLIPTRANSMITTEROVER

REPLACEWITH TWOTYPE 2032BATTERIES

SIDE UP

CH2CH1

CH2CH1

PRESS PROGRAM BUTTON(CHANNEL 1 OR 2)FOR THREE SECONDSTHEN RELEASE

LED WILL FLASH, COUNTING THETOTAL NUMBER OF TRANSMITTERSPROGRAMED TO THAT CHANNEL

REMOVE VISOR CLIPBY REMOVING THREESCREWS

CH2CH1

CONTINUOUSLY FLASHING LED MAYINDICATE ELECTRICAL NOISEINTERFERRENCE

HOW TO ORDER REPAIR PARTS

DEVANCO CANADA19192 HAY ROAD, UNIT Q

SUMMERSTOWN, ON K0C 2E0

TOLL FREE: 855-931-3334www.devancocanada.com

WHEN ORDERING REPAIR PARTSPLEASE SUPPLY THE FOLLOWING INFORMATION:

3 PART NUMBER 3 DESCRITPION 3 MODEL NUMBER