for furniture exclusively brought to you by...
Transcript of for furniture exclusively brought to you by...
ww
w.h
afel
e.co
m.a
u
sliding & foldingdoor essentialsfor furnitureexclusively brought to you by häfele
Häfele - sliding & folding door essentials - for furniture / 07.16
2
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
contentssliDing AnD folDing Door - essentiAls for furniture
flush fitted forefront infront
system name Configuration Max. door height (mm)
Max. door width (mm)
door thickness (mm)
Max. door weight (kg)
no. of doors
soft Close Page no.
eKu frontino 20 flush fitted 1000 598 - 1198 19 20 2 yes 4 - 5
eKu frontino 40 flush fitted 2400 598 - 1198 19 40 2 yes 6
eKu combino 20/35 forefront 2200 1200 19 20 and 35 2 or 3 yes 7
eKu combino 45 forefront 2400 1400 19 - 25 45 2 or 3 yes 8
eKu combino 60 forefront 2600 1400 25 60 2 or 3 yes 9
eKu clipo 16 infront 1400 1000 16 - 19 16 2 yes 10 - 11
eKu clipo 26/36 infront 2200 1000 19 - 25 26 and 36 2 or 3 yes 12 - 13
sliDo classic 55 infront – – 16 + 55 2 or 3 no 14
infront
system name Configuration Max. door height (mm)
Max. door width (mm)
glass thickness (mm)
Max. door weight (kg)
no. of doors
soft Close Page no.
eKu clipo 16 infront 1400 1000 6.38 16 2 yes 16 - 17
sliDo Design 25 infront – – 6 and 8 25 2 no 18 - 19
eKu clipo 36 infront 2000 1000 6 and 8 36 2 yes 20 - 21
tiMber doors
fraMeless glass doors
3
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
bi-folding folding & sliding
system name Configuration Max. door height (mm)
Max. door width (mm)
door thickness (mm)
Max. door weight (kg)
no. of doors Page no.
sAlice concertina
bi-folding - 500 16 - 19 25 2 22
hAWA Multifold 30W
bi-folding 2600 500 19 - 25 30 2 23
tWinline 25/50 bi-folding - 450 16 - 19 25 and 50 2 24 - 25
hAWA Multifold 30
folding & sliding 2600 500 19 - 25 30 2, 4, 6 26
folding doors
Pivot sliding
system name Configuration Max. door height (mm)
Max. door width (mm)
door thickness (mm)
Max. door weight (kg)
no. of doors Page no.
hAWA concepta 25/30/40/50
Pivot sliding 1250 - 2800 900 19 - 50 25, 30, 40, 50 1 28
hAWA folding concepta 25
Pivot folding 1250 - 2600 700 19 - 28 25 2 29
Pivot sliding & Pivot folding doors
Pivot folding
Häfele - sliding & folding door essentials - for furniture / 07.16
4
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
1 for 2 doors
eKu-frontino 20 for tiMber DoorstoP or bottoM running, uP to 20Kg
bottoM running
flush fitted
5
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
fitting sets for cabinet width (mm) door width (mm) Cat. no.version
for furnituretop running or bottom running,
for 2 doors
1200 - 1399 597 - 696 406.02.0601400 - 1599 697 - 796 406.02.0611600 - 1799 797 - 896 406.02.0631800 - 1999 897 - 996 406.02.0642000 - 2199 997 - 1096 406.02.0652200 - 2400 1097 - 1196 406.02.066
for kitchenstop running, with concealed fixings
for 2 doors
1200 - 1399 597 - 696 406.02.0701400 - 1599 697 - 796 406.02.0711600 - 1799 797 - 896 406.02.0721800 - 1999 897 - 996 406.02.0732000 - 2199 997 - 1096 406.02.0742200 - 2400 1097 - 1196 406.02.075
top running installation bottom running installation
> Max. door height (mm): 1000
> Door width (mm): 597 - 1196 > Door thickness (mm): 18-25
> Material: Aluminium, rollers: Plastic > running gear: bottom or top running, 4-point guidance > running gear guided by: ball bearings
> Door stop: stopper system with soft closing mechanism integrated in running equipment
> Mounting: running gear and rails for screw fixing > installation depth (mm): 270
> Max. handle depth (mm): 50
> Distance from handle to door edge: handle depth
> Door arrangement: symmetrical
note: > both doors must have identical dimensions. > the door width specified in the ordering table was calculated with 2 mm door gaps.
1
1
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue ......................................................p. 1.4 - 1.5
toP running
Packing: 1 set
Häfele - sliding & folding door essentials - for furniture / 07.16
6
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
> version: symmetrical door arrangement > Max. door height (mm): 2380 (cabinet 2400)
> Door width (mm): 594 – 1194 > Door thickness (mm): 19
> Material: Aluminium, rollers: Plastic > running gear: top running, 4-point guidance > running gear guided by: ball bearings
> Door stop: stopper system with soft closing mechanism integrated in running equipment
> Mounting: running gear and rails for screw fixing > installation depth (mm): top 250, bottom 170
> Max. handle depth (mm): 30
> Distance from handle to door edge: equal to handle depth
eKu-frontino 40 for tiMber DoorstoP running, uP to 40Kg
fitting sets for cabinet width (mm) door width (mm) Cat. no.version
tall cabinettop running,for 2 doors
1200-1799 594-893 406.02.0551800-2199 894-1093 406.02.0562200-2400 1094-1194 406.02.057
top running installation
1
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.12 - 1.13
note: both doors must have identical dimensions. the door width specified in the ordering table was calculated with 3 mm door gaps.
1 for 2 doors
flush fitted
Packing: 1 set
7
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
running rails and accessories Material Colour/finish length (mm) Cat. no.
upper guide rail, pre-drilled Aluminium bright2500 405.52.0263500 405.52.036
lower running rail, pre-drilled Aluminium Anodised2500 406.31.9023500 406.31.903
cover profile, for upper guides Aluminium Anodised2500 406.31.9123500 406.31.913
intermediate stop, for 3 door fitting sets Plastic/steel grey/galvanised – 405.93.020
> Max. door height (mm): 2200
> Max. door width (mm): 1200
> Door thickness (mm): 19
> height adjustment (mm): eccentric adjustment of +4/-2
1 for 2 doors 2 for 3 doors
note: insert retaining clips before assembly of the double guide rail.
fitting sets for 2 doors for 3 doorsversioneKu combino 20 405.91.125 405.91.134eKu combino 20 soft close 405.91.126 –eKu combino 35 405.91.224 405.91.232eKu combino 35 soft close 405.91.226 –
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.24 - 1.25
eKu-coMbino 20/35 for tiMber Doors bottoM running, uP to 20/35Kg, With soft close MechAnisM (oPtionAl)
forefront
Packing: 1 set
Packing: 1 piece
8
Häfele - sliding & folding door essentials - for furniture / 07.16
Dim
ensi
ons
in m
m d
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
eKu-coMbino 45 for tiMber DoorsbottoM running, uP to 45Kg,With soft close MechAnisM (oPtionAl)
> Max. door height (mm): 2400
> Max. door width (mm): 1400
> Door thickness (mm): 19 – 25
> height adjustment (mm): eccentric height adjustment of ±3 on running gear
> features: easy door mounting comfortable rail mounting and stopper adjustment from front
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.34 - 1.35
fitting sets door thickness (mm) for 2 doors for 3 doorsversion
eKu combino 4519 405.91.242 405.91.24325 405.91.252 405.91.253
eKu combino 45 soft close19 405.91.244 –25 405.91.254 –
running rails and accessories Material length (mm) Cat. no.
upper guide rail, with screw mounting holesAluminium, bright
2500 405.52.0263500 405.52.036
lower running rail, with screw mounting holesAluminium, anodised
2500 406.31.9223500 406.31.923
cover profile for upper guides on outer doorAluminium,anodised
2500 406.31.9123500 406.31.913
centre door stopper for outer door for 3 door sets Plastic, grey – 405.93.020
1 for 2 doors 2 for 3 doors
forefront
Packing: 1 set
Packing: 1 piece
9
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
eKu-coMbino 60 for tiMber DoorsbottoM running, uP to 60Kg,With soft close MechAnisM (oPtionAl)
> Max. door height (mm): 2600
> Max. door width (mm): 1400
> Door thickness (mm): 25
> Adjustment (mm): comfortable eccentric height adjustment of +4/-2 on running gear
> features: tool-less door mounting via spring-loaded guide system running rails suitable for all types of cabinets
> recommended door overlay (mm): 20 - 30
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.46 - 1.47
fitting sets for 2 doors for 3 doorsversioneKu-combino 60 405.71.122 405.71.131eKu-combino 60 405.71.124 –
1 for 2 doors 2 for 3 doors
note: install guide buffers into running and guide railsbefore assembly.
running rails and accessories Material length (mm) Cat. no.
upper guide rail, pre-drilledAluminium,anodised
2500 401.57.0263500 401.57.036
lower running rail, pre-drilledAluminium,anodised
2500 401.58.9263500 401.58.936
intermediate stop, for 3 door fitting set Plastic, grey – 406.32.080
forefront
Packing: 1 set
Packing: 1 piece
Häfele - sliding & folding door essentials - for furniture / 07.16
10
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
eKu-cliPo 16 for tiMber Doors toP running, uP to 16Kg,With soft close MechAnisM (oPtionAl)
infront
Cabinet installation
Serving hatch installation
Cabinet installation
Serving hatch installation
version A With single running rails, swivel lug mounted
version A with clip-on running gear and thumbwheel adjuster
version B with concealed slide-in running gear
version A With single running rails, screw mounted
version B With dual running rail, screw mounted
door overlap
Minimum door width for 1 soft close mechanism - 400 mm
Minimum door width for 2 soft close mechanism - 620 mm
11
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
running rails and accessories Material Colour/finish length (mm) Cat. no.
single running rail, for screw fixing.Min. timber thickness 30 mm.
Aluminium bright2500 405.87.0823500 405.87.083
single running rail with swivel lugs (not for hardwood or MDf).Min. timber thickness 19 mm.
Aluminium bright2500 405.87.0923500 405.87.093
running rail-end piece with swivel lug (not for hardwood or MDf).
Plastic grey – 405.83.180
running rail-end piece for screw fixing Plastic grey – 405.83.181
Double running rail, for screw fixing.Min. timber thickness 19 mm.
Aluminium bright2500 405.90.0323500 405.90.033
single bottom guide rail, ribbed, for press fitting and glue fixing into 7 mm groove
Plastic Anthracite 2500 405.98.517
soft closing mechansim for retrofitting or for soft closing on both sides, with installation instructions
Plastic grey< 8kg 405.10.0778 – 16 kg 405.10.070
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.58 - 1.59
fitting sets for 2 doorsversion
Afor 2 doors 405.82.216
for 2 doors with 8-16 kg soft close mechanism (2 pieces), Min. door width = 620 mm
405.82.218
B for 1 door with installation instructions 405.82.220
Packing: 1 set
Packing: 1 piece
> Max. door height (mm): 1400
> Max. door width (mm): 1000
> Door thickness (mm): 16 – 19
> height adjustment (mm): +2/-1 on running gear using adjusting wheel
> Material: housing, running gear and guide: plastic > running gear: top running, 2 rollers. friction bearing
mounted plastic roller, steel axle > Door stop: top stopper, with retainer for sliding into
single top running rail > installation: housing for screw fixing, running gear without
tools (quick fixing system), guide for press fitting into drill hole
note:order one soft closing mechanism each for door widths of 400 mm to 620 mm, two soft closing mechanisms for door widths above 620 mm.
Cabinet installation
Serving hatch installation
version B running gear installationversion A running gear installation
Häfele - sliding & folding door essentials - for furniture / 07.16
12
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
eKu-cliPo 26/36 for tiMber Doors toP running uP to 26 / 36Kg With soft close MechAnisM (oPtionAl)
installation of housing
infront
CLIPO 36
CLIPO 26
version B running gear installationversion A running gear installation
version A with clip-on running gear version B with concealed slide-in running gear
13
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
> Door height (mm): version A: <2,200, version B: <2,400 > Door width (mm): <1,000 > Door thickness (mm): 19–25
> Material: housing: Plastic, running gear: Zinc alloy, guide: Plastic
> running gear: top running; clipo 26 with 2 rollers, clipo 36 with 4 rollers
> running gear guided by: friction bearing mounted plastic roller
> Door stopper: top stopper, with retainer for sliding into single top running track
1 for 2 doors
fitting sets Model Cat. no.version
Afor 2 doors
clipo 26 405.00.004clipo 36 405.02.404
for 3 doors clipo 36 405.02.405B for 1 door clipo 36 405.02.408
note:order one soft closing mechanism for door widths of 420 mm to 620 mm, two soft closing mechanisms for door widths above 620 mm.
running rails and accessories Material finish/colour length (m) Cat. no.
single running rail, with swivel lug Aluminiumsilver coloured anodised
2.5 405.00.6423.5 405.00.643
single running rail, pre-drilled, for screw fixing Aluminiumsilver coloured anodised
2.5 405.00.6223.5 405.00.623
bottom guide rail, for glue fixing Aluminium bright2.5 405.04.2513.5 405.04.351
Double running rail, pre-drilled, for screw fixing Aluminiumsilver coloured anodised
2.5 405.02.6023.5 405.02.603
single running rail end piece, for screw fixing Plastic grey – 405.00.072single running rail end piece, with swivel lug Plastic – – 405.00.073soft closing mechanism for door weights up to 15 kg
Plastic– – 405.10.073
soft closing mechanism for door weights up to 26 kg 405.10.074soft closing mechanism for door weights up to 36 kg Aluminium 940.48.045
2 for 3 doors
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue ...............................................p.. 1.75A - 1.77
Packing: 1 set
Packing: 1 piece
Häfele - sliding & folding door essentials - for furniture / 07.16
14
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
sliDo-clAssic 55 for tiMber DoorsbottoM running, uP to 55Kg
> Door thickness (mm): ≥16
> running gear: bottom running, 1 roller > running gear guided by: steel ball bearing
> height adjustment (mm): ±2
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 1.82 - 1.83
fitting sets Cat. no.versionfor 2 doors 402.23.000for 2 doors with height adjustment 402.23.002for 3 doors 402.23.001for 3 doors with height adjustment 402.23.003
1 for 2 doors 2 for 3 doors
note: > fitting sets with height adjustment have a different drilling pattern for both doors with or doors without height adjustment. the centre door always has the drill hole for the height adjustment on the left hand side. other doors always have the drill hole at the edge next to the side panel.
> excellent running characteristics due to large roller diameters > individual door thickness possible
running rails and accessories Material Colour/finish length (mm) Cat. no.
single guide rail, top, not drilled Aluminium bright2500 402.23.802
3500 402.23.803
single running rail, bottom, for press fitting, barbed Aluminium bright2500 402.23.602
3500 402.23.603
single running rail, bottom, surface mountingAluminium silver coloured
anodised
2500 402.26.622
3500 402.26.623
forstner drill bit, Ø 50 mm, 10 mm shank, for mounting the rollers in drilled holes
– – 001.04.145
infront
Packing: 1 set
Packing: 1 piece
get uP to DAte stocK & Pricing inforMAtion, on All the ProDucts in this cAtAlogue. Plus Much More!
the neW hAfele.coM.Au!register noW!
Häfele - sliding & folding door essentials - for furniture / 07.16
16
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
1 for 2 doors.
eKu-cliPo 16 for frAMeless glAss DoorstoP running, uP to 16 KgWith soft close MechAnisM (oPtionAl)
infront
Installation dimensions
Door overlap
Clipo 16 GPK
Clipo 16 GPPK
Installation dimensions
Door overlap
Clipo 16 GPK
Clipo 16 GPPK
Installation dimensions
Door overlap
Clipo 16 GPK
Clipo 16 GPPKversion A: for top glass fixing profile and visible bottom guide. shown with surface mounted running rails.
version B: for top and bottom glass fixing profile and invisible bottom guide. shown with surface mounted running rails.
version B: for top and bottom glass fixing profile and invisible bottom guide. shown with recess mounted running rails.
17
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
> version: A for top glass fixing profile and visible bottom guide. B for top and bottom glass fixing profile and invisible bottom guide
> Max. door height (mm): 1400
> Max. door width (mm): 1000
> glass thickness (mm): 6 - 6.38
> height adjustment: +2/-1 mm on running gear
> Material: Plastic > running gear: top running, 2 rollers > running gear guided by: friction bearing
> Door stop: top stopper, with retainer > installation: running gear without tools (quick fixing
system), guide for screw fixing
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 3.14 - 3.15
With oPtionAl soft close
running rails and accessories Material Colour/finish length (mm) Cat. no.
Double top running rail, for screw fixing, surface mountedMin. installation depth = 19 mm
Aluminiumsilver anodised
2500 405.90.9623500 405.90.963
Double top running rail, for screw fixing, recess mountedMin. installation depth = 19 mm
Aluminiumsilver anodised
2500 405.90.9723500 405.90.973
rail end piece, with swivel lugs (not suitable for hardwood/ MDf)
Plastic grey – 405.83.180
rail end piece, for screw fixing Plastic grey – 405.83.181
glass fixing profile, for glue fixing, for top and bottom of door Aluminiumsilver anodised
2500 405.89.9323500 405.89.933
soft close mechanism, for door weight up to 8 kg for soft closing on both sides, with installation instructions
Plastic grey – 405.10.077
soft close mechanism, for door weight from 8 to 16 kg for soft closing on both sides, with installation instructions
Plastic grey – 405.10.070
elch Pro 3b silicone adhesive 310 mlhighly flexible, acetate curing silicone sealant
transparent – 405.54.020
fitting sets for 2 doorsversion A clipo 16, for top glass fixing profile and visible bottom guide. for 2 doors. 405.82.290 B clipo 16, for top and bottom glass fixing profile and invisible bottom guide. for 2 doors. 405.82.291
Packing: 1 set
Packing: 1 piece
note:order one soft closing mechanism each for door widths of 400 mm to 620 mm, two soft closing mechanisms for door widths above 620 mm.
Häfele - sliding & folding door essentials - for furniture / 07.16
18
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
sliDo-Design 25 for frAMeless glAss DoorsbottoM running, uP to 25Kg
> running gear: bottom running, 1 roller > running gear guided by: ball bearing mounted,plastic coated roller
> glass thickness (mm): 6 and 8
note:Quick and easy installation, running gears with slide-in technology for sliding into runner housing profile. very smooth running action.
end piece
end piece with finger grip
end piece set with lock and centrepiece, open-type
closed-typeglass width: !
open-typeglass width: 2
glass width: 2
closed-typeglass width: !
open-typeglass width: 2
Calculations:
glass height: c = x - (25 + 8)
glass width:A = internal cabinet widthb = door overlapn = number of door leavesne = number of end panels
! A + b - ne x 2.5 n
2 A + b n
Mounting aid for running gear
infront
1 for 2 doors
running gear installation
19
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
system componentsglass thickness (mm)
for 2 doors, closed-type, without lock
for 2 doors, closed-type, with lock
for 2 doors, open-type without lock
for 2 doors, open-type with lock
Cat. no.
running gear, for sliding in and tightening
6 and 8 4 4 4 4 415.13.103
Mounting aid for running gear 6 and 8 1 1 1 1 415.13.060
Anti-derailment device and gasket, for clipping on and screwing into guide rail (length 50 mm)
68 8 8 8
415.13.050
8 415.13.051
end piece, closed-type (for clipping on and tighening)
6 and 8 2 2 – – 415.13.020
end piece, open-type (for clipping on and tightening)
6 and 8 – – 2 2 415.13.021
end piece with finger grip, closed-type (for clipping on and tightening)
6 and 8 2 –– – – 415.13.170
end piece with finger grip, open-type (for clipping on and tightening)
6 and 8 – – 2 – 415.13.010
end piece with lock, and counterpiece, open type
6 and 8 – 1 – 1 233.02.410
vcs18 cylinder core with reversible key, including 2 keys (up to 2000 key changes), with door lift-up safeguard (for clipping on and tightening)
– – KD* – KD* 210.30.600
– – KA* – KA* 210.30.601
running rails and accessoriesglass thickness (mm)
Material Colour/finish length (mm) Cat. no.
Double top guide rail, for screw fixing
6 and 8 Aluminium silver anodised2500 415.10.9255000 415.10.950
Double bottom running rail, for screw fixing, for use with end cap turn cylinder (233.02.410)
6 and 8 Aluminium silver anodised2500 415.11.925
5000 415.11.950
Double bottom running rail for screw fixing, for use with efl 41 sliding door lock.
6 and 8 Aluminium silver anodised 3500 415.08.972
runner housing profile, for fixing the runner to the glass door
6 and 8 Aluminium silver anodised2500 415.12.925
5000 415.12.950
rubber profile for fixing glass into running housing profile**
6 and 8 rubber black
1.0 x 32 x 2000
416.10.020
1.5 x 32 x 2000
416.10.021
2.0 x 32 x 2000
416.10.022
Dust protection profile6 Aluminium,
Plasticsilver anodised,grey
5000 416.13.9358 416.13.925
note** groove in runner housing profile is 9 mm wide. this is important information for selecting the suitable rubber width. the inserted pane of glass may not exactly fit in the profiles as considerable tolerances can occur with glass. in this case it is required to glue the pane of glass into the profile using silicone, for example.
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 3.18 - 3.19
note*order Keyed to differ (KD) or keyed alike (KA) cylinder core as required.
running gear installation
Packing: 1 set
Packing: 1 piece
Häfele - sliding & folding door essentials - for furniture / 07.16
20
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
eKu-cliPo 36 for frAMeless glAss DoorstoP running, uP to 36Kg.With soft close MechAnisM (oPtionAl)
infront
version A: for top glass fixing profile and visible bottom guide.version B: for top and bottom glass fixing profile and invisible bottom guide.
version C: for top glass clamp fixing and visible bottom guide.
version A version B version C (1 Door) version C (2 Doors)shown with surface mounted running rails
1 for 2 doors
21
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................p. 3.21A - 3.21b and 3.23A - 3.23b
> version: A for top glass fixing profile and visible bottom guide. B for top and bottom glass fixing profile and invisible bottom guide. C for top glass clamp fixing and visible bottom guide.
> Door height (mm): <2,000 > Door width (mm): <1,000 > for glass door thickness (mm): 6 – 8
> Material: running gear and suspension fitting: Zinc alloy, guide: Zinc alloy or plastic
> running gear: top running, 4 rollers > running gear guided by: friction bearing mounted plastic roller, steel
axle. > Door stop: With retaining spring for sliding into top
running rail > soft close mechanism: optional, for sliding into top running rail.
running rails and accessories Material finish/colour length (mm) Cat. no.
single running rail, with swivel lug. Aluminium silver coloured, anodised2500 405.00.6423500 405.00.643
single running rail, pre-drilled, for screw fixing.
Aluminium silver coloured, anodised2500 405.00.6223500 405.00.623
single running rail, pre-drilled, with flange for screw fixing.
Aluminium silver coloured, anodised2500 405.00.6523500 405.00.653
single running rail for surface mounting, pre-drilled, for screw fixing.
Aluminium silver coloured, anodised2500 405.00.6323500 405.00.633
Double running rail, pre-drilled, for screw fixing.not to be used with version C with top glass clamps.
Aluminium silver coloured, anodised2500 405.02.6223500 405.02.623
single running rail end piece, with swivel lug. Plastic – – 405.00.073
glass fixing profile, top and bottom, for glue fixing.not to be used with version C with top glass clamps.
Aluminium silver coloured, anodised2500 405.03.2023500 405.03.203
soft closing mechanism for door weights up to 26 kg. Plastic,Aluminium
– –405.10.074
soft closing mechanism for door weights up to 36 kg. 940.48.045
clip panel, for clipping onto glass clamp shoe, for version C only
Aluminium silver coloured, anodised2500 405.23.9023500 405.23.903
end caps and fixing clips for clip panel, for version C only Plastic Anthracite – 405.02.050
locking system Cat. no.
locking system for version B, with cylinder, right 405.02.090
locking system for version B, with cylinder, left 405.02.091* left hand lock shown
fitting sets version Cat. no.
for 1 door
A for top glass fixing profile and visible bottom guide.
405.02.410
B for top and bottom glass fixing profile and invisible bottom guide.
405.02.411
C for top glass clamp fixing and visible bottom guide.
405.02.409
Packing: 1 set
Packing: 1 piece
Packing: 1 piece
note:order one soft closing mechanism for door widths of 420 mm to 620 mm, two soft closing mechanisms for door widths above 620 mm.
Häfele - sliding & folding door essentials - for furniture / 07.16
22
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
sAlice - concertinA for tiMber Doors uP to 15Kg. (30 Kg Per PAir)
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue ...................................................... p. 5.4 - 5.5
saliCe Concertina complate fitting set Cat. no.
for 1 pair of doors 409.95.000
note:sAlice hinges and mounting plates for carcase must be ordered separately.
Position the sliding block inside the rail by rotating it 90º.
lock the sliding block into position by turning the lever, marked in red.
assemblyMount the hinges of the fixed door onto the mounting plates on the cabinet side. We recommend the use of sAlice hinge 329.17.600 with mounting plate 329.71.500 or similar.
bi-folding
supplied with: > 1 piece 409.95.710, hinge for sliding block > 1 piece 409.95.720, sliding block > 3 pieces 354.07.710, central hinge with offset knuckle > 1 piece 409.96.712, upper running rail > 2 meters 950.07.914, adhesive finger-protection strip
> Depth adjustment of the hinges mounted on the sliding component is achieved through the fixing screw of the hinge.
> Depth adjustment should be made in conjunction with the hinges mounted on opposing doors.
> this adjustment is useful to keep the “l” value constant along the front of the furniture.
height adjustment
+2 mm -2 mm
> height adjustment of hinges assembled with the sliding components is achieved through a cam.
> through this alignment a parallel movement of the component in the running rail is achieved.
> the result is a smooth movement without any binding.
depth adjustment
+2.5 mm
note:recommended maximum door leaf width 500 mm.
note:the sliding block does not have a load-bearing function it must slide freely inside the running rail.
Packing: 1 set
23
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
hAWA-MultifolD 30W for tiMber DoorsuP to 30Kg (60Kg Per PAir)
> Max. door height (mm): 2600
> Door width (mm): 200-500 > Door thickness (mm): 18-25
> height adjustment (mm): ± 2 on the running gear
> features: Same fitting applicable for Infront and Forefront installations Light, quiet running Horizontal seals reduce sound Quick assembly Lower guide not required, suitable for accessible cabinets without bottom panel
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue ...................................................... p. 5.8 - 5.9
fitting sets for 2 doorsfor 1 outer panel pair 409.52.050
note:Please order accessories separately
running rails and accessories Material Colour/finish Packing Cat. no.interlocking door holder, between two panel pairs Plastic black 1 Pair 409.50.940sealing profile, for pressing into 2.5 mm groove. 5000 mm length rubber black 1 roll 409.54.300
Milling jig for guides and suspension unitlaminated timber
– 1 Piece 409.50.990
bi-folding
Packing: 1 set
Packing: 1 piece
Häfele - sliding & folding door essentials - for furniture / 07.16
24
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
tWinline 25/50 for tiMber DoorsuP to 25/50Kg Per PAir
bi-folding
60 + doors thickness
tWinline 25/50
T
2956
56
64
36,5
T
X =
56
+ T
X =
56
+ T
Ø35
53Ø
53Ø
> features: load bearing running gears with two-wheel guidance running gears clip-mount into top track Durable all-metal components
tWinline 25 > Max. door width (mm): 550
> Door weight (kg): 25 (12.5 per door leaf) > Door thickness (mm): 16 - 19
tWinline 50 > Max. door width (mm): 600
> Door weight (kg): 50 (25 per door leaf) > Door thickness (mm): 16 - 19
number of concealed hinges per doorthe graph shown gives guideline information only.A trial hanging is recommended.
the number of concealed hinges per door depends on:•Doorwidthandheight•Doorweight•Doormaterial
According to the example graph, three concealed hinges have to be mounted at a door height of 1,500 mm and a door weight of 9 to 12 kg.
tW
inl
ine
25
tW
inl
ine
50
25
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
tWinline 25for door weights up to 25 kg
basic set left hand
basic setright hand
basic set left and right hand
standard set left hand
standard set right hand
standard set left and right hand
top running gear with 1 hinge (left/right hand) 1 1 2 1 1 2connecting hinge with central knuckle 3 3 6connecting hinge with lateral adjustment 3 3 6cover cap, plastic, white 1 1 2Door to carcase alignment fitting 1 1Door to door alignment fitting 1Cat no. 409.36.000 409.36.002 409.36.008 409.36.001 409.36.003 409.36.009
tWinline 50for door weights up to 50 kg
basic set left hand
basic setright hand
basic set left and right hand
standard set left hand
standard set right hand
standard set left and right hand
top running gear with 2 hinges (left/right hand) 1 1 2 1 1 2connecting hinge with central knuckle 4 4 8connecting hinge with lateral adjustment 4 4 8cover cap, plastic, white 1 1 2Door to carcase alignment fitting 1 1Door to door alignment fitting 1Cat. no. 409.36.004 409.36.006 409.36.010 409.36.005 409.36.007 409.36.011
Material length (mm) Cat. no.
top running rail profile Aluminium
1500 409.31.601
2000 409.31.602
3050 409.31.603
Packing: 1 piece
Packing: 1 piece
Packing: 1 piece
1 2
6
3 4
7
5
8
installation
running rails
Häfele - sliding & folding door essentials - for furniture / 07.16
26
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
hAWA-MultifolD 30 for tiMber DoorsuP to 30Kg (60Kg Per PAir)
> Max. door height (mm): 2600
> Door width (mm): 500 (650 when fixed to carcase) > Door thickness (mm): 19-25
> height adjustment (mm): ± 2 on the running gear
> running gear guided by: 2 ball bearing, plastic-coated
2 guide rolls of plastic > installation also possible in the fully assembled cabinets
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue ...................................................... p. 6.8 - 6.9
fitting sets for 2 doorsversionfor 1 outer panel pair 409.52.010for 1 centre panel pair 409.52.020for 1 outer panel pair, with concealed hinges 409.52.030
running rails and accessories Material Colour/finish length (mm) Packing Cat. no
upper running rail and lower guide rail set Aluminium silver anodised2500 1 set 409.53.9253500 1 set 409.53.935
interlocking door holder, between two panel pairs Plastic black – 1 Pair 409.50.940folding door connection piece for connecting two panel pairs steel nickel-plated – 1 Piece 409.50.930sealing profile, for pressing into 2.5 mm groove rubber black 5000 1 roll 409.54.300
Milling jig for guides and suspension unitlaminated timber
– – 1 Piece 409.50.990
central concealed hinge, with automatic closing Aluminium, zinc die-cast
– – 1 Piece 343.91.600
folding & sliding
Packing: 1 set
Packing: 1 piece
27
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
> cAD DAtA> Mounting instructions. > ProDuct inforMAtion> stocK AvAilAbility> Price
AvAilAble online 24/7 At
WWW.hAfele.coM.Au
register At WWW.hAfele.coM.Au noW!
Häfele - sliding & folding door essentials - for furniture / 07.16
28
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
hAWA-concePtA 25/30/40/50 for tiMber Doors uP to 25/30/40/50Kg
> features: Pivot/slide timber doors for furniture and room partitioning solutions. unique scissor technology Accommodates large and heavy doors Adjustments are made from the front. All components are fixed on to the intermediate panel. can be used in left or right handed applications.
> Door height (mm): 1250 – 1850 for concepta 25 1851 – 2300 for concepta 30 1851 – 2500 for concepta 40 2301 – 2850 for concepta 50
> Door width (mm): 300 – 900 > Door thickness (mm): timber doors: 19 – 50
note: > for large and heavy timber doors > Modular system with four design options > carcase-independent covering of wall cavities > Door adjustment from the front > body-side connection and angle for surface mounted
doors must be ordered separately.
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 7.10 - 7.15
fitting sets application door height (mm) door weight (kg) Cat. no.
for 1 door for timber doors
1250 - 1850 25 408.30.0151851 - 2300 30 408.30.0161851 - 2500 40 408.30.0172301 - 2850 50 408.30.018
Packing: 1 piece
accessories Width (mm) Material finish length (mm) Cat. no
connecting profile. order 2 pieces per door for connecting end panel to carcase.
55 Aluminiumsilver anodised
650 408.30.091
900 408.30.092
interconnecting profile, for connecting 2 concepta fittings together. order 2 pieces for connecting 2 concepta fitting sets.
110 Aluminiumsilver anodised
650 408.30.093
900 408.30.094
Pivot sliding
Packing: 1 set
29
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
hAWA-folDing concePtA 25 for tiMber Doors uP to 25Kg
> Door width (mm): 300 - 700 > Door height (mm): 1250 - 1850 or 1851-2600 > Max door weight (kg): 25 (per pair of panels 50)
> Door thickness (mm): 19 - 35
> features: two pairs of folding doors enables complete opening of cabinets up to 2800 mm in width the folding door pair can be pushed fully flush with the external side room-high designs without a cabinet base allow for recess enclosures and walk-in cabinets with uninterrupted flooring cabinet designs for countertop to ceiling possible Adjustment are made from the front integrated cabinet and side connectors for easy and simplified installation unique scissor technology prevents jamming when folding and sliding lock catch assembly for use with espagnolette locks
note: > for large and heavy timber doors > Modular system with four design options > carcase-independent covering of wall cavities > Door adjustment from the front
fitting setdoor height (mm)
door weight (kg)
Cat. no.
for 1 pair of folding doors
1250 - 1850left 408.30.019right 408.30.020
1851 - 2600left 408.30.021right 408.30.022
accessories Width (mm) Material finish Cat. nodoor positiong / door centering
bottom profile complete 1300 mm including cover cap, leading ramp and drilling jig aluminium anodised
– Aluminium silver anodised 408.30.961
Magnetic centering part, including drilling jig, aluminium anodised 55 Aluminium silver anodised 408.30.229reinforcement profile – Aluminium Anodised 408.30.970
Pivot folding
Packing: 1 set
Packing: 1 piece
for detailed product information: > refer the sliding and folding hardware for furniture
catalogue .................................................. p. 7.16 - 7.18
Häfele - sliding & folding door essentials - for furniture / 07.16
30
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
inDex
001. 001.04.145................................................. 14
210. 210.30.600................................................. 19
210.30.601................................................. 19
233. 233.02.410................................................. 19
233.02.410................................................. 19
329. 329.17.600................................................. 22
329.71.500................................................. 22
343. 343.91.600................................................. 26
354. 354.07.710................................................. 22
401. 401.57.026................................................... 9
401.57.036................................................... 9
401.58.926................................................... 9
401.58.936................................................... 9
402. 402.23.000................................................. 14
402.23.001................................................. 14
402.23.002................................................. 14
402.23.003................................................. 14
402.23.602................................................. 14
402.23.603................................................. 14
402.23.802................................................. 14
402.23.803................................................. 14
402.26.622................................................. 14
402.26.623................................................. 14
405. 405.00.004................................................. 13
405.00.072................................................. 13
405.00.073................................................. 13
405.00.073................................................. 21
405.00.622................................................. 13
405.00.622................................................. 21
405.00.623................................................. 13
405.00.623................................................. 21
405.00.632................................................. 21
405.00.633................................................. 21
405.00.642................................................. 13
405.00.642................................................. 21
405.00.643................................................. 13
405.00.643................................................. 21
405.00.652................................................. 21
405.00.653................................................. 21
405.02.050................................................. 21
405.02.090................................................. 21
405.02.091................................................. 21
405.02.404................................................. 13
405.02.405................................................. 13
405.02.408................................................. 13
405.02.409................................................. 21
405.02.410................................................. 21
405.02.411................................................. 21
405.02.602................................................. 13
405.02.603................................................. 13
405.02.622................................................. 21
405.02.623................................................. 21
405.03.202................................................. 21
405.03.203................................................. 21
405.04.251................................................. 13
405.04.351................................................. 13
405.10.070................................................. 11
405.10.070................................................. 17
405.10.073................................................. 13
405.10.074................................................. 13
405.10.074................................................. 21
405.10.077................................................. 11
405.10.077................................................. 17
405.23.902................................................. 21
405.23.903................................................. 21
405.52.026................................................... 7
405.52.026................................................... 8
405.52.036................................................... 7
405.52.036................................................... 8
405.54.020................................................. 17
405.71.122................................................... 9
405.71.124................................................... 9
405.71.131................................................... 9
405.82.216................................................. 11
405.82.218................................................. 11
405.82.220................................................. 11
405.82.290................................................. 17
405.82.291................................................. 17
405.83.180................................................. 11
405.83.180................................................. 17
405.83.181................................................. 11
405.83.181................................................. 17
405.87.082................................................. 11
405.87.083................................................. 11
405.87.092................................................. 11
405.87.093................................................. 11
405.89.932................................................. 17
405.89.933................................................. 17
405.90.032................................................. 11
405.90.033................................................. 11
405.90.962................................................. 17
405.90.963................................................. 17
405.90.972................................................. 17
405.90.973................................................. 17
405.91.125................................................... 7
405.91.126................................................... 7
405.91.134................................................... 7
405.91.224................................................... 7
405.91.226................................................... 7
405.91.232................................................... 7
405.91.242................................................... 8
405.91.243................................................... 8
405.91.244................................................... 8
405.91.252................................................... 8
405.91.253................................................... 8
405.91.254................................................... 8
405.93.020................................................... 7
405.93.020................................................... 8
405.98.517................................................. 11
406. 406.02.055................................................... 6
406.02.056................................................... 6
406.02.057................................................... 6
406.02.060................................................... 5
406.02.061................................................... 5
406.02.063................................................... 5
406.02.064................................................... 5
406.02.065................................................... 5
406.02.066................................................... 5
406.02.070................................................... 5
406.02.071................................................... 5
406.02.072................................................... 5
406.02.073................................................... 5
406.02.074................................................... 5
406.02.075................................................... 5
406.31.902................................................... 7
406.31.903................................................... 7
406.31.912................................................... 7
406.31.912................................................... 8
406.31.913................................................... 7
406.31.913................................................... 8
406.31.922................................................... 8
406.31.923................................................... 8
406.32.080................................................... 9
408. 408.30.015................................................. 29
408.30.016................................................. 29
408.30.017................................................. 29
408.30.018................................................. 29
408.30.019................................................. 31
408.30.020................................................. 31
408.30.021................................................. 31
408.30.022................................................. 31
31
Dim
ensi
ons
in m
m D
imen
sion
al d
ata
not b
indi
ng, i
mag
es a
re fo
r illu
stra
tive
purp
oses
onl
y. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
inDex408.30.091................................................. 29
408.30.092................................................. 29
408.30.093................................................. 29
408.30.094................................................. 29
408.30.229................................................. 31
408.30.961................................................. 31
408.30.970................................................. 31
409. 409.36.000................................................. 25
409.36.001................................................. 25
409.36.002................................................. 25
409.36.003................................................. 25
409.36.004................................................. 25
409.36.005................................................. 25
409.36.006................................................. 25
409.36.007................................................. 25
409.36.008................................................. 25
409.36.009................................................. 25
409.36.010................................................. 25
409.36.011................................................. 25
409.50.930................................................. 26
409.50.940................................................. 23
409.50.940................................................. 26
409.50.990................................................. 23
409.50.990................................................. 26
409.52.010................................................. 26
409.52.020................................................. 26
409.52.030................................................. 26
409.52.050................................................. 23
409.53.925................................................. 26
409.53.935................................................. 26
409.54.300................................................. 23
409.54.300................................................. 26
409.95.000................................................. 22
409.95.710................................................. 22
409.95.720................................................. 22
409.96.712................................................. 22
415. 415.08.972................................................. 19
415.10.925................................................. 19
415.10.950................................................. 19
415.11.925................................................. 19
415.11.950................................................. 19
415.12.925................................................. 19
415.12.950................................................. 19
415.13.010................................................. 19
415.13.020................................................. 19
415.13.021................................................. 19
415.13.050................................................. 19
415.13.051................................................. 19
415.13.060................................................. 19
415.13.103................................................. 19
415.13.170................................................. 19
416. 416.10.020................................................. 19
416.10.021................................................. 19
416.10.022................................................. 19
416.13.925................................................. 19
416.13.935................................................. 19
940. 940.48.045................................................. 13
940.48.045................................................. 21
950. 950.07.914................................................. 22
732.04.679 Sliding & folding door eSSentialS - for furniture - 07.2016
häfele australia Pty. ltd. | 8 Monterey road | dandenong | Victoria 3175Phone: 1300 659 728 | fax: (03) 9212 2001 | email: [email protected] | www.hafele.com.au
häfele new Zealand ltd. | 16 accent drive | east tamaki | auckland 2013Phone: 0800 442 335 | email: [email protected] | www.hafele.co.nz
hÄfele loCations:
australia i MelBourne i SYdneY i neWCaStle i BriSBane i adelaide i launCeSton i HoBart i PertH
new Zealand i auCkland i Wellington i CHriStCHurCH