FM guide

7/21/2019 FM guide

http://slidepdf.com/reader/full/fm-guide 1/167

Fire PumpsBefore ordering a fire pump, consult FM Approvals regarding size, type of driver, suction supplies and location. Proposals for fire pump installations, including plans showinglocation and piping connections, should be sent to FM Global for review before the order is placed. Give the manufacturer complete data, including rated capacity, net headand suction head. Contracts for pump installations or changes should be let subsequent to acceptance of plans and subject to satisfactory field tests by FM Global.

The pump manufacturer or his authorized representative is responsible for furnishing a complete unit consisting of pump, driver and necessary accessories, all according toFM Global's standards.

Satisfactory performance in an operating test after installation should be guaranteed. A new fire pump installation is not acceptable until FM Global has witnessed a

satisfactory field acceptance test. This will include a test of endurance of the pump and reliability of the power supply.Exact horsepower requirements for each pump must be determined by a shop test on the specific pump. Approximate horsepower requirements at rated pump conditions aas follows:

Rated Capacity,gal/min(dm3

/min)

Rated Net

Head, psi (kPa)

ApproximatePower

Required,hp (kW)

500(1895)

100(690)

50-60(37-45)

750(2840)

100(690)

60-75(45-56)

1000

(3785)

100

(690)

75-100

(56-75)

1500(5680)

100(690)

100-125(75-93)

2000(7570)

100(690)

125-150(93-112)

2500(9465)

100(690)

150-200(112-149)

In the listings on the following page, rated net head represents the amount of pressure boost obtainable from a pump of a given type and impeller size when operating atrated speed.

The rated net head range indicates that impellers of various diameters are obtainable for the given type of pump.

Although not recommended for installations where suction is normally taken under lift, FM Approved pumps have been tested for proper operation under negative suctionconditions up to 15 ft (5 m) at 150% of rated capacity.

Centrifugal Fire Pumps, Horizontal Split-Case TypeFM Approved horizontal split-case type centrifugal fire pumps are relatively simple to operate and repair. These pumps have a two-part casing divided in a horizontal planthrough the shaft centerline. They are well suited to fire protection service where a water supply is obtainable under a positive head.

Horizontal Mounted

ACME Pumps Asia Pte Ltd48A Changi South St 1, Singapore 486114

ProductListingCountry

RatedCapacity,(gal/min)

RatedCapacity,(dm³/min)

RatedNet Headat RatedCapacity,

psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.

DischargeOutlet,dia., in.

Stage(s)Certificatio

Type

HVS125-80-250F Singapore 500 1895 75-135 515-930 2965 5 3 FM Approve


HVS125-80-250F Singapore 500 1895 111-193 765-1330 3550 5 3 FM ApproveHVS125-80-315F Singapore 500 1895 113-200 780-1380 2975 5 3 FM Approve













© 2007-2011 FM Approvals. All rights reserved. 1 of 167

7/21/2019 FM guide












Armstrong Integrated LimitedMucklow Hill, Heyward Wharf, Halesowen, West Midlands, UK B62 8DJ





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.


Stage(s)Certification

Type

5x4x12HFUnitedKingdom

500 1895 41-63 285-435 1780 5 4 1 FM Approved

5x4x12HF UnitedKingdom

500 1895 41-91 285-625 2100 5 4 1 FM Approved

5x4-10FUnitedKingdom

500 1895 41-92 285-635 2600 5 4 1 FM Approved


500 1895 44-120 305-830 2945 5 4 1 FM Approved


500 1895 46-124 315-855 3000 5 4 1 FM Approved


500 1895 48-107 330-740 2800 5 4 1 FM Approved


500 1895 53-116 365-800 2350 5 4 1 FM Approved


500 1895 66-175 455-1205 3560 5 4 1 FM Approved

BP-FUnitedKingdom

500 1895 75-135 515-930 1760 5 4 1 FM Approved

8x6x16F UnitedKingdom

750 2840 40-76 276-524 1450 8 6 1 FM Approved


750 2840 45-68 310-470 1780 6 5 1 FM Approved

6x5x9.5FUnitedKingdom

750 2840 47-67 324-462 2600 6 5 1 FM Approved


750 2840 54-92 370-635 2600 6 5 1 FM Approved


750 2840 56-80 386-552 2800 6 5 1 FM Approved

6x5x12MFUnitedKingdom

750 2840 56-115 386-793 2350 6 5 1 FM Approved

BE-FUnitedKingdom

750 2840 60 415 1775 6 5 1 FM Approved


750 2840 63-90 434-620 2945 6 5 1 FM Approved

6x5-10F UnitedKingdom

750 2840 63-107 435-740 2800 6 5 1 FM Approved

8x6x16FUnitedKingdom

750 2840 64-116 441-800 1780 8 6 1 FM Approved


750 2840 66-94 455-648 3000 6 5 1 FM Approved


750 2840 71-117 490-805 2945 6 5 1 FM Approved


750 2840 72-143 496-986 2600 6 5 1 FM Approved


750 2840 74-123 510-850 3000 6 5 1 FM Approved


750 2840 77-170 530-1170 3560 5 4 1 FM Approved


750 2840 80-112 550-770 2945 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 83-116 570-800 3000 5 4 1 FM Approved


750 2840 83-126 572-869 2350 6 5 1 FM Approved

5x4-12HFUnitedKingdom

750 2840 84-107 580-740 2350 5 4 1 FM Approved

6x5x12MF

United

Kingdom 750 2840 85-167 586-1151 2800 6 5 1 FM Approved


750 2840 90-164 620-1131 2100 8 6 1 FM Approved

BP-FUnitedKingdom

750 2840 95-125 655-860 1760 5 4 1 FM Approved


750 2840 95-186 655-1282 2945 6 5 1 FM Approved


750 2840 98-137 676-945 3560 6 5 1 FM Approved


750 2840 99-153 683-1055 2200 8 6 1 FM Approved


750 2840 110-175 760-1025 3560 6 5 1 FM Approved


750 2840 115-177 793-1220 2350 8 6 1 FM Approved

6x5x12MF

United



1000 3785 51-96 350-660 1780 6 5 1 FM Approved


1000 3785 52-73 359-503 1450 8 6 1 FM Approved

8x6-10LFUnitedKingdom

1000 3785 60-93 415-640 2600 8 6 1 FM Approved


1000 3785 61-114 421-786 1780 8 6 1 FM Approved


1000 3785 63-125 435-860 2945 8 6 1 FM Approved


1000 3785 65-129 450-890 3000 8 6 1 FM Approved


1000 3785 73-81 503-558 2945 6 5 1 FM Approved

6x5-15F

United



1000 3785 77-85 531-586 3000 6 5 1 FM Approved


1000 3785 77-120 531-827 2350 6 5 1 FM Approved


1000 3785 85-127 586-876 3560 6 5 1 FM Approved


1000 3785 88-112 605-770 2945 6 5 1 FM Approved


1000 3785 88-162 605-1117 2100 8 6 1 FM Approved


1000 3785 92-117 635-805 3000 6 5 1 FM Approved


1000 3785 93-134 641-924 2600 6 5 1 FM Approved

8x6x16FUnited

Kingdom1000 3785 97-152 669-1048 2200 8 6 1 FM Approved


1000 3785 99-170 685-1170 3560 6 5 1 FM Approved

BN-FUnitedKingdom

1000 3785 100 690 1770 6 5 1 FM Approved


1000 3785 104-177 717-1220 2945 6 5 1 FM Approved


1000 3785 111-158 765-1089 2800 6 5 1 FM Approved


1000 3785 113-175 779-1206 2350 8 6 1 FM Approved


1000 3785 135-220 931-1862 3560 6 5 1 FM Approved


1000 3785 162-236 1115-1625 2960 6 5 1 FM Approved


7/21/2019 FM guide


8x6x12-1/2HFUnitedKingdom

1250 4730 40-73 275-505 1780 8 6 1 FM Approved


1250 4730 48-70 331-483 1450 8 6 1 FM Approved

8x6x12-1/2MFUnitedKingdom

1250 4730 51-78 352-538 2350 8 6 1 FM Approved

8x6x16F

United



1250 4730 58-106 400-730 2100 8 6 1 FM Approved

8x6x10LFUnitedKingdom

1250 4730 74-120 510-825 2945 8 6 1 FM Approved


1250 4730 75-92 515-635 1790 6 5 1 FM Approved


1250 4730 76-134 525-925 2350 8 6 1 FM Approved


1250 4730 77-125 530-860 3000 8 6 1 FM Approved


1250 4730 77-133 530-915 2100 6 5 1 FM Approved


1250 4730 85-158 586-1089 2100 8 6 1 FM Approved

8x6x10LF

United



1250 4730 90-170 620-1170 2350 6 5 1 FM Approved


1250 4730 94-150 648-1034 2200 8 6 1 FM Approved


1250 4730 110-173 758-1193 2350 8 6 1 FM Approved


1250 4730 116-212 800-1460 2600 6 5 1 FM Approved

8x6x12-1/2LFUnitedKingdom

1250 4730 121-188 835-1295 2945 8 6 1 FM Approved

8x6x12-1/2LFUnitedKingdom

1250 4730 125-195 860-1345 3000 8 6 1 FM Approved


1250 4730 136-205 940-1415 2800 6 5 1 FM Approved

8x6x12-1/2LF

United



1250 4730 146-259 1007-1785 3560 6 5 1 FM Approved


1250 4730 155-229 1070-1580 2960 6 5 1 FM Approved

8x6x15 HFUnitedKingdom

1500 5680 47-148 324-1020 1450 8 6 1 FM Approved


1500 5680 50-72 345-495 1780 8 6 1 FM Approved


1500 5680 50-75 345-517 1780 8 6 1 FM Approved

BK-FUnitedKingdom

1500 5680 52-95 360-655 1760 8 6 1 FM Approved


1500 5680 53-103 365-710 2100 8 6 1 FM Approved

8x6x12-1/2MFUnited



1500 5680 72-107 496-738 1780 8 6 1 FM Approved


1500 5680 72-130 495-895 2350 8 6 1 FM Approved


1500 5680 74-148 510-1020 2100 8 6 1 FM Approved


1500 5680 81-154 558-1062 2100 8 6 1 FM Approved


1500 5680 83-126 572-869 2600 8 6 1 FM Approved


1500 5680 90-146 620-1006 2200 8 6 1 FM Approved


1500 5680 95-114 655-785 2945 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 96-187 662-1289 2350 8 6 1 FM Approved

BV-FUnitedKingdom

1500 5680 100 690 1750 8 6 1 FM Approved


1500 5680 100-119 690-820 3000 8 6 1 FM Approved

8x6x15MF

United



1500 5680 106-170 731-1172 2350 8 6 1 FM Approved


1500 5680 109-170 750-1170 3560 8 6 1 FM Approved


1500 5680 111-167 765-1151 2945 8 6 1 FM Approved


1500 5680 122-164 840-1130 2350 6 5 1 FM Approved


1500 5680 122-206 840-1420 2600 6 5 1 FM Approved


1500 5680 128-197 885-1360 2800 6 5 1 FM Approved


1500 5680 146-223 1005-1540 2960 6 5 1 FM Approved

8x6x12-1/2LF

United



2000 7570 45-54 310-372 1780 10 8 1 FM Approved


2000 7570 54-57 370-395 1450 10 8 1 FM Approved


2000 7570 59-80 407-552 2100 10 8 1 FM Approved


2000 7570 60-91 415-625 1780 10 8 1 FM Approved


2000 7570 61-85 420-585 1780 10 8 1 FM Approved


2000 7570 70-107 483-738 1780 8 6 1 FM Approved


2000 7570 73-130 505-895 2100 10 8 1 FM Approved

8x6x15MF

United



2000 7570 87-141 600-972 2100 8 6 1 FM Approved


2000 7570 87-182 600-1255 2350 8 6 1 FM Approved


2000 7570 95-153 655-1055 2350 10 8 1 FM Approved

BU-FUnitedKingdom

2000 7570 100 690 1760 10 8 1 FM Approved


2000 7570 120-142 827-979 2100 8 6 1 FM Approved


2000 7570 140-202 965-1395 2945 10 8 1 FM Approved


2500 7570 80-85 550-585 1780 10 8 1 FM Approved

10x8-14HFUnited



2000 7570 100-146 690-1007 2945 10 8 1 FM Approved


2500 7570 108-149 745-1025 2350 10 8 1 FM Approved


2000 7570 128-165 883-1151 2945 10 8 1 FM Approved


2500 7570 140-197 965-1360 2945 10 8 1 FM Approved

Audoli & Bertola divisione di Gruppo Aturia SpAPizza Aturia 920060 Gessate (Milan) Italy


7/21/2019 FM guide






psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

PDN150-300L

Italy 750 2840 53-86 365-590 2100 8 6 1 FM Approved

PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300M


PDN150-300L

Italy 1000 3785 80 550 2100 8 6 1 FM Approved

PDN150-300M


PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300L


PDN150-300M


PDN150-300M


PDN150-300L


PDN150-300H


PDN150-300H


PDN150-300M


PDN150-300H


PDN150-300H


PDN150-300M


PDN150-300H


PDN150-300M


PDN150-300M


PD200-250B


PD200-250B


PD200-250B


PDN150-300L


PDN150-300H


PD200-250B


PD200-250B



7/21/2019 FM guide


PD200-250B


PDN150-300H


PDN150-300H


PDN

150-300H Italy 1500 5680 135-171 595-755 2970 8 6 1 FM Approved

PD200-250B


PDN150-300H


PD200-250B


PD200-250B


PD200-250B


PD200-250B


PD200-250B


PDN

200-300M Italy 2000 7570 110-119 760-820 2350 10 8 1 FM Approved

PDN200-300M


PDN200-300M


PDN200-300M


PD200-250B


Corcoran Piping Systems500 Ternes Dr, Monroe, Michigan 48162, USA

ProductListing

Country




psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

SP100/48UnitedStates of America

400 1515 102-126 703-869 1760 5 4 1 FM Approved


450 1705 102-126 703-869 1760 5 4 1 FM Approved


500 1895 45-67 310-462 1450 6 5 1 FM Approved


500 1895 100-126 689-869 1760 5 4 1 FM Approved


750 2840 88-118 607-814 1450 8 5 1 FM Approved


750 2840 88-115 607-793 1450 8 6 1 FM Approved


750 2840 130-178 896-1227 1760 8 5 1 FM Approved


1500 5680 67-79 462-545 1100 12 8 1 FM Approved


750 2840 70-100 483-689 1760 6 5 1 FM Approved


1000 3780 77-88 531-607 1100 8 6 1 FM Approved


7/21/2019 FM guide



1000 3780 85-116 586-800 1450 8 5 1 FM Approved


1000 3780 86-114 593-786 1450 8 6 1 FM Approved

SP150/48

United

States of America

1000 3780 127-168 876-1158 1760 8 6 1 FM Approved


1000 3780 129-178 889-1227 1760 8 5 1 FM Approved


1000 3780 142-155 979-1068 1450 8 6 1 FM Approved


1250 4730 75-86 517-593 1100 8 6 1 FM Approved


1250 4730 85-112 586-772 1450 8 6 1 FM Approved


1250 4730 96-117 662-807 1450 10 8 1 FM Approved


1250 4730 124-166 855-1144 1760 8 6 1 FM Approved


1250 4730 125-174 862-1200 1760 8 5 1 FM Approved


1250 4730 142-153 979-1055 1450 8 6 1 FM Approved


1500 5680 72-83 496-572 1100 8 6 1 FM Approved


1500 5680 94-117 648-807 1450 10 8 1 FM Approved

SP150/48UnitedStates of

America

1500 5680 121-162 834-1117 1760 8 6 1 FM Approved


1500 5680 138-151 951-1041 1450 8 6 1 FM Approved


1500 5680 142-172 979-1186 1760 10 8 1 FM Approved


2000 7570 65-77 448-531 1100 12 8 1 FM Approved


2000 7570 90-115 621-793 1450 10 8 1 FM Approved


2000 7570 123-139 848-958 1450 12 8 1 FM Approved

SP200/48

United

States of America

2000 7570 139-172 958-1186 1760 10 8 1 FM Approved


2500 9465 61-65 421-448 1100 14 10 1 FM Approved


2500 9465 120-136 827-938 1450 12 8 1 FM Approved


2500 9465 133-168 917-1158 1760 10 8 1 FM Approved


3000 11,355 61-65 421-448 1100 14 10 1 FM Approved


3000 11,355 106-112 731-772 1450 14 10 1 FM Approved


7/21/2019 FM guide



3500 13,250 60-64 414-441 1100 14 10 1 FM Approved


3500 13,250 106-112 731-772 1450 14 10 1 FM Approved

SP250/50

United

States of America

4000 15,140 106-111 731-765 1450 14 10 1 FM Approved


250 945 100-110 690-760 2900 3 2 1/2 1 FM Approved


300 1135 98-110 675-760 2900 3 2 1/2 1 FM Approved


250 945 146-163 1005-1125 3500 3 2 1/2 1 FM Approved


300 1135 145-161 1000-1110 3500 3 2 1/2 1 FM Approved


400 1515 140-154 965-1060 3500 3 2 1/2 1 FM Approved


250 945 96-106 660-730 2900 4 3 1 FM Approved


300 1135 95-105 655-725 2900 4 3 1 FM Approved


400 1515 93-103 640-710 2900 4 3 1 FM Approved


400 1515 136-149 940-1025 3500 4 3 1 FM Approved


500 1895 134-147 925-1015 3500 4 3 1 FM Approved

SP100/24UnitedStates of

America

500 1895 87-114 600-785 2900 6 4 1 FM Approved


500 1895 126-166 870-1145 3500 6 4 1 FM Approved


750 2840 122-160 840-1105 3500 6 4 1 FM Approved

SP125/24HUnitedStates of America

500 1895 96-115 660-795 2900 6 5 1 FM Approved


750 2840 93-111 640-765 2900 6 5 1 FM Approved


1000 3785 89-108 615-745 2900 6 5 1 FM Approved

SP125/24H

United

States of America

1250 4730 84 580 2900 6 5 1 FM Approved


500 1895 139-163 960-1125 3500 6 5 1 FM Approved


750 2840 136-162 940-1115 3500 6 5 1 FM Approved


1000 3785 132-156 910-1075 3500 6 5 1 FM Approved


500 1895 116-167 800-1150 2900 6 5 1 FM Approved


750 2840 116-166 800-1145 2900 6 5 1 FM Approved


7/21/2019 FM guide



500 1895 169-238 1165-1640 3500 6 5 1 FM Approved


750 2840 188-237 1295-1635 3500 6 5 1 FM Approved

SP125/38H

United

States of America

750 2840 204-280 1405-1930 2900 6 5 1 FM Approved


1000 3785 197-277 1360-1910 2900 6 5 1 FM Approved

5x6-12HKUnitedStates of America

500 1895 374-482 2580-3325 3500 6 5 2 FM Approved

5x6-12BHK

UnitedStates of America

500 1895 287-373 1980-2570 2900 6 5 2 FM Approved

Aurora Pump A Member of the Pentair Pump Group800 Airport Rd, North Aurora, Illinois 60542, USA

When requested, Aurora can furnish pumps designed for applications where suction pressures exceed 40 psi (275 kPa). These pumps are designated by the addition othe letter "H" after the type designation.





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

2-1/2-481-10BUnitedStates of America

250 945 52-167 360-1150 3560 3 2 1/2 1 FM Approved

2-1/2-481-10BUnitedStates of America

250 945 50-115 345-795 2950 3 2 1/2 1 FM Approved

2-491-8AUnitedStates of America

250 945 55-112 380-770 3550 4 2 1 FM Approved

3-481-10

United

States of America

500 1895 50-150 345-1030 3560 4 3 1 FM Approved

3-481-10UnitedStates of America

250 945 40-121 275-835 2950 4 3 1 FM Approved


250 945 40-100 275-690 3560 4 3 1 FM Approved

3-481-10/DIUnitedStates of America

500 1895 50-150 345-1030 3560 4 3 1 FM Approved


250 945 40-100 275-690 3560 4 3 1 FM Approved


250 945 40-121 275-835 2950 4 3 1 FM Approved

3-491-9CUnitedStates of America

500 1895 91-142 625-980 3550 5 3 1 FM Approved


500 1895 55-125 380-860 3300 5 3 1 FM Approved


500 1895 66-146 455-1005 3550 5 3 1 FM Approved


500 1895 126-165 870-1140 3525 4 3 1 FM Approved


750 2840 40-50 275-345 1770 5 4 1 FM Approved


7/21/2019 FM guide



500 1895 40-55 275-380 1770 5 4 1 FM Approved


500 1895 55-134 380-925 2950 5 4 1 FM Approved

4-481-11C

United

States of America

750 2840 65-205 450-1415 3560 5 4 1 FM Approved


750 2840 66-165 455-1140 3300 5 4 1 FM Approved


500 1895 75-170 515-1170 3300 5 4 1 FM Approved

4-481-11C/DIUnitedStates of America

750 2840 65-205 450-1415 3560 5 4 1 FM Approved


500 1895 55-134 380-925 2950 5 4 1 FM Approved


750 2840 66-165 455-1140 3300 5 4 1 FM Approved


500 1895 75-170 515-1170 3300 5 4 1 FM Approved

4-481-11DUnitedStates of America

750 2840 81-190 560-1310 3550 5 4 1 FM Approved


500 1895 63-138 435-950 3000 5 4 1 FM Approved


500 1895 61-134 420-925 2950 5 4 1 FM Approved


500 1895 60-80 415-550 1770 5 4 1 FM Approved

4-481-15UnitedStates of

America

750 2840 71-97 490-670 1770 5 4 1 FM Approved


500 1895 150-210 1030-1450 1770 5 4 2 FM Approved


750 2840 96-154 660-1060 3000 6 4 1 FM Approved


750 2840 95-198 655-1365 3300 6 4 1 FM Approved


750 2840 95-230 655-1585 3550 6 4 1 FM Approved


500 1895 40-55 275-380 1770 6 4 1 FM Approved

4-491-11C

United

States of America

750 2840 123-144 850-995 3000 6 4 1 FM Approved


750 2840 143-209 985-1440 3550 6 4 1 FM Approved


750 2840 139-178 960-1230 3300 6 4 1 FM Approved


750 2840 57-152 395-1050 2300 6 4 1 FM Approved


750 2840 51-87 350-560 1770 6 4 1 FM Approved


750 2840 55-126 380-870 2100 6 4 1 FM Approved


7/21/2019 FM guide



1000 3785 91-153 625-1055 2300 6 4 1 FM Approved


750 2840 54-90 370-620 1770 6 4 1 FM Approved

4-491-14C

United

States of America

750 2840 59-131 405-905 2100 6 4 1 FM Approved


750 2840 73-160 505-1105 2300 6 4 1 FM Approved


1000 3785 95-123 655-850 2100 6 4 1 FM Approved


500 1895 72-116 495-780 3550 6 4 1 FM Approved


500 1895 49-82 340-565 3000 6 4 1 FM Approved


750 2840 67-78 460-540 3000 6 4 1 FM Approved


750 2840 73-96 505-660 3300 6 4 1 FM Approved


750 2840 63-113 435-780 3550 6 4 1 FM Approved


500 1895 61-100 420-690 3300 6 4 1 FM Approved


750 2840 100-135 690-930 3275 6 4 1 FM Approved


750 2840 100-160 690-1105 3550 6 4 1 FM Approved


America

500 1895 105-145 725-1000 3275 6 4 1 FM Approved


500 1895 110-170 760-1170 3550 6 4 1 FM Approved


500 1895 125 860 2500 5 4 1 FM Approved


500 1895 40-80 275-550 1750 5 4 1 FM Approved


500 1895 100-125 690-860 2200 5 4 1 FM Approved


500 1895 100 690 2000 5 4 1 FM Approved

4-492-14

United

States of America

500 1895 100 690 2280 5 4 1 FM Approved


750 2840 100-125 690-860 2500 5 4 1 FM Approved


750 2840 71-125 490-860 1750 5 4 1 FM Approved


500 1895 76-125 525-860 1750 5 4 1 FM Approved


500 1895 100-120 690-825 3500 5 4 1 FM Approved


500 1895 60-100 415-690 3500 5 4 1 FM Approved


7/21/2019 FM guide



500 1895 121-125 835-860 3500 5 4 1 FM Approved

5-481-11BUnitedStates of America

1000 3785 101-165 695-1140 3300 6 5 1 FM Approved

5-481-11B

United

States of America

1000 3785 120-200 830-1380 3550 6 5 1 FM Approved

5-481-11B/DIUnitedStates of America

1000 3785 101-165 695-1140 3300 6 5 1 FM Approved


1000 3785 120-200 830-1380 3550 6 5 1 FM Approved


1000 3785 88-135 605-930 3300 6 5 1 FM Approved


1000 3785 90-160 620-1105 3550 6 5 1 FM Approved


750 2840 105-154 725-1060 2950 6 5 1 FM Approved


1000 3785 97-146 670-1005 2950 6 5 1 FM Approved


1000 3785 88-135 605-930 3300 6 5 1 FM Approved


1000 3785 97-146 670-1005 2950 6 5 1 FM Approved


750 2840 105-154 725-1060 2950 6 5 1 FM Approved


1000 3785 90-160 620-1105 3550 6 5 1 FM Approved

5-481-11DUnitedStates of

America

1500 5680 90-120 620-830 3300 6 5 1 FM Approved


750 2840 50-70 345-485 1770 6 5 1 FM Approved


1000 3785 50-94 345-650 1770 6 5 1 FM Approved


1000 3785 90-128 620-885 1770 6 5 1 FM Approved


500 1895 185-335 1275-2310 3000 5 5 2 FM Approved


500 1895 227-475 1565-3275 3550 5 5 2 FM Approved

5-485-12

United

States of America

500 1895 178-323 1225-2225 2950 5 5 2 FM Approved


500 1895 68-144 470-995 1480 6 5 2 FM Approved


750 2840 40-62 275-430 1770 8 5 1 FM Approved


1000 3785 40-60 275-415 1770 8 5 1 FM Approved


1000 3785 51-88 350-605 1770 8 5 1 FM Approved


1000 3785 73-125 505-860 2100 8 5 1 FM Approved


7/21/2019 FM guide



1000 3785 92-151 635-1040 2300 8 5 1 FM Approved


1250 4730 64-84 440-580 1780 8 5 1 FM Approved

5-491-14A

United

States of America

1250 4730 94-121 650-835 2100 8 5 1 FM Approved


1250 4730 116-147 800-1015 2300 8 5 1 FM Approved


1000 3785 85-138 585-950 1770 8 5 1 FM Approved


1000 3785 88-200 605-1380 2100 8 5 1 FM Approved


1000 3785 109-242 750-1670 2300 8 6 1 FM Approved


750 2840 94-203 650-1400 2100 8 5 1 FM Approved


750 2840 113-244 780-1680 2300 8 5 1 FM Approved


750 2840 89-143 615-985 1770 8 5 1 FM Approved


1000 3785 95-145 655-1000 3275 8 5 1 FM Approved


1000 3785 95-170 655-1170 3550 8 5 1 FM Approved


750 2840 105-150 725-1035 3275 8 5 1 FM Approved


America

750 2840 105-180 725-1240 3550 8 5 1 FM Approved


1000 3785 100 690 2500 6 5 1 FM Approved


750 2840 40-80 275-550 1750 6 5 1 FM Approved


1000 3785 51-80 350-550 1750 6 5 1 FM Approved


1000 3785 81-125 560-860 1750 6 5 1 FM Approved


750 2840 100-125 690-860 3500 6 5 1 FM Approved

5-495-15

United

States of America

750 2840 125-180 860-1240 1750 6 5 2 FM Approved


1000 3785 40-52 275-360 1770 8 6 1 FM Approved

6-481-11HHUnitedStates of America

1000 3785 69-115 476-793 2600 8 6 1 FM Approved


1250 4732 96-110 662-758 2600 8 6 1 FM Approved


1250 4732 98-145 676-1000 2950 8 6 1 FM Approved


1250 4732 102-151 703-1041 3000 8 6 1 FM Approved


7/21/2019 FM guide


7/21/2019 FM guide



1250 4732 122-247 841-1703 3300 8 6 1 FM Approved


1000 3785 130-248 896-1710 3300 8 6 1 FM Approved

6-481-14HH

United

States of America

1250 4732 145-287 1000-1979 3560 8 6 1 FM Approved


1250 4730 55-96 380-660 1770 8 6 1 FM Approved


1500 5680 50-93 345-640 1770 8 6 1 FM Approved


2000 7570 100-125 690-860 2100 8 6 1 FM Approved


2000 7570 80-100 550-690 1770 8 6 1 FM Approved


1250 4730 55-95 380-655 1770 8 6 1 FM Approved


1500 5680 71-91 490-625 1770 8 6 1 FM Approved


1250 4730 100-138 690-950 1770 8 6 1 FM Approved


1500 5680 95-134 655-925 1770 8 6 1 FM Approved


1250 4730 100-138 690-950 1770 8 6 1 FM Approved


1500 5680 95-134 655-925 1770 8 6 1 FM Approved

6-481-18CUnitedStates of

America

1500 5680 75-103 515-710 1480 8 6 1 FM Approved


2000 7570 100-140 690-965 1770 8 6 1 FM Approved


1250 4730 78-106 540-730 1480 8 6 1 FM Approved


1000 3785 80-108 552-745 1480 8 6 1 FM Approved


1250 4730 78-106 540-730 1480 8 6 1 FM Approved


1000 3785 80-108 552-745 1480 8 6 1 FM Approved

6-481-18C/DI

United

States of America

2000 7570 100-140 690-965 1770 8 6 1 FM Approved


1500 5680 80-165 550-1140 1770 8 6 1 FM Approved


1250 4730 87-168 600-1160 1770 8 6 1 FM Approved


2000 7570 120-152 830-1050 1770 8 6 1 FM Approved


1250 4730 87-168 600-1160 1770 8 6 1 FM Approved


1500 5680 80-165 550-1140 1770 8 6 1 FM Approved


7/21/2019 FM guide



2000 7570 120-152 830-1050 1770 8 6 1 FM Approved


750 2840 304-506 2095-3490 3550 6 6 2 FM Approved

6-485-12

United

States of America

750 2840 193-248 1330-1710 2600 6 6 2 FM Approved


750 2840 206-344 1420-2370 2950 6 6 2 FM Approved


750 2840 205-357 1415-2460 3000 6 6 2 FM Approved


750 2840 80-175 550-1205 1480 8 6 2 FM Approved


750 2840 138-246 950-1695 1770 8 6 2 FM Approved


1000 3785 130-243 895-1675 1770 8 6 2 FM Approved

6-485-17A/DIUnitedStates of America

750 2840 138-246 950-1695 1770 8 6 2 FM Approved


750 2840 80-175 550-1205 1480 8 6 2 FM Approved


1000 3785 130-243 895-1675 1770 8 6 2 FM Approved


1500 5680 42-55 290-380 1770 10 6 1 FM Approved

6-491-11XUnitedStates of America

750 2840 40-56 275-385 1770 6 6 1 FM Approved

6-491-12AUnitedStates of

America

750 2840 147-218 1015-1505 3300 6 6 1 FM Approved


750 2840 179-265 1235-1825 3565 6 6 1 FM Approved


500 1895 157-190 1080-1310 3000 6 6 1 FM Approved


500 1895 163-233 1125-1605 3300 6 6 1 FM Approved


500 1895 97-140 670-965 2600 6 6 1 FM Approved


500 1895 148-164 1020-1130 2800 6 6 1 FM Approved

6-491-12A

United

States of America

500 1895 191-277 1315-1910 3565 6 6 1 FM Approved


750 2840 132-148 910-1020 2800 6 6 1 FM Approved


750 2840 142-175 980-1205 3000 6 6 1 FM Approved


1500 5680 96-164 660-1130 2300 10 6 1 FM Approved


2000 7570 89-131 615-905 2100 10 6 1 FM Approved


2000 7570 88-160 605-1105 2300 10 6 1 FM Approved


7/21/2019 FM guide



1500 5680 95-135 655-930 2100 10 6 1 FM Approved


1500 5680 88-151 605-1040 2300 10 6 1 FM Approved

6-491-14C

United

States of America

1500 5680 76-86 525-593 1770 10 6 1 FM Approved


1500 5680 88-100 605-690 1900 10 6 1 FM Approved


1500 5680 84-125 580-860 2100 10 6 1 FM Approved


2000 7570 105-173 725-1195 2100 10 6 1 FM Approved


2000 7570 87-134 560-925 1770 10 6 1 FM Approved


2000 7570 132-200 910-1380 2100 10 6 1 FM Approved


2000 7570 110-157 760-1085 1770 10 6 1 FM Approved


1000 3785 105-182 725-1255 3570 10 6 1 FM Approved


1000 3785 105-145 725-1000 3300 10 6 1 FM Approved


1500 5680 100-175 690-1205 3570 10 6 1 FM Approved


1500 5680 95-135 655-930 3300 10 6 1 FM Approved


America

1000 3785 40-55 275-380 1750 8 6 1 FM Approved


1500 5680 70-90 485-620 1750 8 6 1 FM Approved


1500 5680 90-145 620-1000 1750 8 6 1 FM Approved


1500 5680 40-50 275-345 1770 10 8 1 FM Approved


1250 4730 43-53 295-365 1770 10 8 1 FM Approved


2000 7570 70-125 485-860 1770 10 8 1 FM Approved

8-481-17B

United

States of America

2000 7570 51-130 350-895 1770 10 8 1 FM Approved


2000 7570 52-94 350-650 1480 10 8 1 FM Approved


2500 9465 75-130 515-895 1770 10 8 1 FM Approved


2500 9465 115-145 795-1000 2100 10 8 1 FM Approved


2000 7570 82-137 565-945 1480 10 8 1 FM Approved


1250 4730 136-200 940-1380 1775 10 8 1 FM Approved


7/21/2019 FM guide



1500 5680 88-143 605-985 1480 10 8 1 FM Approved


1250 4730 90-144 620-995 1480 10 8 1 FM Approved

8-481-21

United

States of America

2000 7570 128-196 880-1350 1775 10 8 1 FM Approved


1500 5680 135-200 930-1380 1775 10 8 1 FM Approved


2500 9465 99-129 685-890 1485 10 8 1 FM Approved


2500 9465 123-193 850-1330 1770 10 8 1 FM Approved


2000 7570 110-173 760-1195 1475 12 8 1 FM Approved


2000 7570 167-220 1150-1515 1775 12 8 1 FM Approved


2500 9465 114-167 785-1150 1475 12 8 1 FM Approved


2500 9465 160-215 1105-1480 1775 12 8 1 FM Approved


2500 9465 88-144 605-995 2300 12 8 1 FM Approved


2500 9465 50-84 345-580 1770 12 8 1 FM Approved


2500 9465 72-119 495-820 2100 12 8 1 FM Approved

8-491-14AUnitedStates of

America

3000 11,355 91-116 625-780 2100 12 8 1 FM Approved


3000 11,355 80 550 1770 12 8 1 FM Approved


2500 9465 112-141 770-970 1785 12 8 1 FM Approved


2500 9465 136-171 940-1180 2100 12 8 1 FM Approved


3000 11,355 103-134 710-925 1770 12 8 1 FM Approved


3000 11,355 130-165 895-1140 2100 12 8 1 FM Approved

8-492-15

United

States of America

1500 5680 40-44 275-305 1750 10 8 1 FM Approved


2000 7570 63-88 435-605 1750 10 8 1 FM Approved


1500 5680 45-69 310-475 1750 10 8 1 FM Approved


2000 7570 100-125 690-860 1750 10 8 1 FM Approved


2000 7570 126-150 870-1035 1750 10 8 1 FM Approved


2500 9465 100-125 690-860 1750 10 8 1 FM Approved


7/21/2019 FM guide



3000 11,355 100-110 690-760 2300 12 10 1 FM Approved


3000 11,355 61-100 420-690 1480 12 10 1 FM Approved

10-481-18

United

States of America

2500 9465 65-101 450-695 1480 12 10 1 FM Approved


3000 11,355 99-140 685-965 1775 12 10 1 FM Approved


3500 13,250 59-97 405-670 1480 12 10 1 FM Approved


3500 13,250 98-140 675-965 1775 12 10 1 FM Approved


4000 15,140 95-110 655-760 1775 12 10 1 FM Approved


3500 13,250 59-94 405-650 1480 12 10 1 FM Approved


3000 11,355 90-138 620-950 1770 12 10 1 FM Approved


3500 13,250 88-135 605-930 1770 12 10 1 FM Approved


3000 11,355 61-95 420-655 1480 12 10 1 FM Approved


2500 7570 63-96 435-660 1480 12 10 1 FM Approved


4000 15,140 62-92 425-635 1480 12 10 1 FM Approved

10-481-18DUnitedStates of

America

4000 15,140 85-134 585-925 1770 12 10 1 FM Approved


4500 17,035 81-132 560-910 1770 12 10 1 FM Approved


5000 18,925 90-130 620-895 1770 12 10 1 FM Approved


4000 15,140 110-225 758-1551 1900 16 10 1 FM Approved


4500 17,035 71-133 489-917 1480 16 10 1 FM Approved


4000 15,140 61-134 420-924 1480 16 10 1 FM Approved

10-491-20

United

States of America

4500 17,035 90-195 620-1344 1785 16 10 1 FM Approved


4500 17,035 106-223 731-1538 1900 16 10 1 FM Approved


5000 18,925 82-132 565-910 1480 16 10 1 FM Approved


5000 18,925 88-195 607-1344 1785 16 10 1 FM Approved


4000 15,140 94-198 648-1365 1785 16 10 1 FM Approved


5000 18,925 102-221 703-1524 1900 16 10 1 FM Approved


7/21/2019 FM guide



2500 9465 62-98 430-675 1750 12 10 1 FM Approved

10-492-18 *UnitedStates of America

3500 13,250 94-151 650-1040 1770 12 10 1 FM Approved

10-492-18 *

United

States of America

3000 11,355 100-153 690-1055 1770 12 10 1 FM Approved


4000 15,140 67-103 460-716 1480 14 12 1 FM Approved


500 1895 163-215 1125-1480 1760 8 6 2 FM Approved


500 1895 166-220 1145-1515 1780 8 6 2 FM Approved


500 1895 243-433 1675-2985 2950 8 6 2 FM Approved


750 2840 154-206 1060-1420 1760 8 6 2 FM Approved


750 2840 158-211 1090-1455 1780 8 6 2 FM Approved


750 2840 183-242 1260-1670 1900 8 6 2 FM Approved


750 2840 206-395 1420-2725 2350 8 6 2 FM Approved


750 2840 215-340 1480-2345 2800 8 6 2 FM Approved


750 2840 229-300 1580-2070 2100 8 6 2 FM Approved


America

750 2840 237-422 1635-2910 2950 8 6 2 FM Approved


750 2840 260-413 1795-2850 2600 8 6 2 FM Approved


1000 3785 145-197 1000-1360 1760 8 6 2 FM Approved


1000 3785 149-202 1025-1395 1780 8 6 2 FM Approved


1000 3785 172-231 1185-1595 1900 8 6 2 FM Approved


1000 3785 195-340 1345-2345 2350 8 6 2 FM Approved

6-485-16

United

States of America

1000 3785 205-329 1415-2270 2800 8 6 2 FM Approved


1000 3785 218-290 1505-2000 2100 8 6 2 FM Approved


1000 3785 228-365 1570-2515 2950 8 6 2 FM Approved


1000 3785 251-403 1715-2780 2600 8 6 2 FM Approved


1250 4732 135-185 930-1275 1760 8 6 2 FM Approved


1250 4732 139-189 960-1305 1780 8 6 2 FM Approved


7/21/2019 FM guide



1250 4732 161-219 1110-1510 1900 8 6 2 FM Approved


1250 4732 183-327 1260-2255 2350 8 6 2 FM Approved

6-485-16

United

States of America

1250 4732 193-317 1330-2185 2800 8 6 2 FM Approved


1250 4732 206-277 1420-1910 2100 8 6 2 FM Approved


1250 4732 216-349 1490-2405 2950 8 6 2 FM Approved


1500 5680 302 2080 2800 8 6 2 FM Approved


1500 5680 336 2315 2950 8 6 2 FM Approved


1250 4732 239-390 1650-2690 2600 8 6 2 FM Approved


1500 5680 170-313 1170-2160 2350 8 6 2 FM Approved


1500 5680 192-262 1325-1805 2100 8 6 2 FM Approved


1500 5680 225-374 1550-2580 2600 8 6 2 FM Approved


2000 7570 52-94 350-650 1480 10 8 1 FM Approved


2000 7570 51-130 350-895 1770 10 8 1 FM Approved

8-481-17B/DIUnitedStates of

America

2500 9465 75-130 515-895 1770 10 8 1 FM Approved


2500 9465 115-145 795-1000 2100 10 8 1 FM Approved


1000 3785 195-379 1345-2615 2350 8 6 2 FM Approved


1000 3785 228-405 1570-2790 2950 8 6 2 FM Approved


1250 4732 183-366 1260-2525 2350 8 6 2 FM Approved


1250 4732 216-390 1490-2690 2950 8 6 2 FM Approved

6-485-16

United

States of America

1500 5680 170-348 1170-2400 2350 8 6 2 FM Approved


1500 5680 170-348 1170-2400 2350 8 6 2 FM Approved


500 1895 215-404 1480-2785 2350 8 6 2 FM Approved


500 1895 168-215 1160-1480 1770 8 6 2 FM Approved


750 2840 158-206 1090-1420 1770 8 6 2 FM Approved


1000 3785 144-188 995-1295 1770 8 6 2 FM Approved


7/21/2019 FM guide



500 1895 222-307 1530-2115 2100 8 6 2 FM Approved


750 2840 213-298 1470-2055 2100 8 6 2 FM Approved

6-485-16B

United

States of America

1000 3785 199-286 1370-1970 2100 8 6 2 FM Approved


1250 4730 196-264 1350-1820 2100 8 6 2 FM Approved


500 1895 218-354 1505-2440 2250 8 6 2 FM Approved


750 2840 209-344 1440-2370 2250 8 6 2 FM Approved


1000 3785 196-332 1350-2290 2250 8 6 2 FM Approved


1250 4730 179-312 1235-2150 2250 8 6 2 FM Approved


500 1895 239-387 1650-2670 2350 8 6 2 FM Approved


750 2840 230-377 1585-2600 2350 8 6 2 FM Approved


1000 3785 217-364 1495-2510 2350 8 6 2 FM Approved


1250 4730 200-346 1380-2385 2350 8 6 2 FM Approved


500 1895 340-435 2345-3000 2600 8 6 2 FM Approved

6-485-16BUnitedStates of

America

750 2840 221-424 1525-2925 2600 8 6 2 FM Approved


1000 3785 208-416 1435-2870 2600 8 6 2 FM Approved


1250 4730 190-401 1310-2765 2600 8 6 2 FM Approved


500 1895 376-446 2595-3075 2950 8 6 2 FM Approved


750 2840 247-441 1705-3040 2950 8 6 2 FM Approved


1000 3785 234-425 1615-2930 2950 8 6 2 FM Approved

6-485-16B

United

States of America

1250 4730 259-410 1785-2825 2950 8 6 2 FM Approved


500 1895 198-360 1365-2480 2250 8 6 2 FM Approved


750 2840 189-352 1305-2425 2250 8 6 2 FM Approved


1000 3785 180-334 1240-2305 2250 8 6 2 FM Approved


1250 4730 169-323 1165-2225 2250 8 6 2 FM Approved


7/21/2019 FM guide


* Max discharge pressure is 200 psi (1380 kPa).

Grundfos (Singapore) Pte Ltd24 Tuas West Road, Singapore 638381, Singapore

ProductListing

Country




psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSF6-12

Singapore 500 1895 40-49 275-340 1450 8 6 - FM Approved

HSF6-12

Singapore 750 2840 44 305 1450 8 6 - FM Approved

HSF6-12


HSF6-16


HSF6-18


HSF5-11


HSF5-11


HSF6-16


HSF6-18


HSF6-16


HSF6-12


HSF6-18


HSF6-12


HSF6-18


HSF6-16


HSF6-12


HSF6-18


HSF6-12


HSF6-18


HSF8-20


HSF8-20G


HSF10-20


HSF6-18


HSF6-12


HSF6-12


HSF6-18

Singapore 1500 5680 188 1295 2000 8 6 - FM Approved

HSF8-17


HSF10-20


HSF8-20G


HSF8-20


HSF8-20G



7/21/2019 FM guide


HSF10-16


HSF10-20


HSF8-20G


HSF

10-16 Singapore 3000 11,355 46-79 315-545 1450 12 10 - FM Approved

HSF10-16

Singapore 3500 13,250 59-76 405-525 1450 12 10 - FM Approved

Grundfos2005 Dr Martin Luther King Jr St, Indianapolis, Indiana 46202, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSDF2-8 *


250 945 40-100 275-690 3530 3 2 1 FM Approved

HSEF4-10G

United

States of America

250 945 58-95 400-655 3000 5 4 1 FM Approved

HSEF4-10G


250 945 61-132 420-910 3525 5 4 1 FM Approved

HSEF4-10


250 945 97-108 670-745 2800 5 4 1 FM Approved

HSEF4-10


250 945 100-125 690-860 3000 5 4 1 FM Approved

HSEF4-10


250 945 100-175 690-1205 3550 5 4 1 FM Approved

HSEF4-10G


300 1135 58-93 400-640 3000 5 4 1 FM Approved

HSEF4-10G


300 1135 61-130 420-895 3525 5 4 1 FM Approved

HSEF4-10G


300 1135 97-108 670-745 2800 5 4 1 FM Approved

HSEF4-10


300 1135 100-125 690-860 3000 5 4 1 FM Approved

HSEF4-10


300 1135 100-174 690-1200 3550 5 4 1 FM Approved

HSEF4-10G


400 1515 55-90 380-620 3000 5 4 1 FM Approved

HSEF

4-10G

UnitedStates of

America

400 1515 59-128 405-885 3525 5 4 1 FM Approved

HSEF4-10


400 1515 96-107 660-740 2800 5 4 1 FM Approved

HSEF4-10


400 1515 98-123 665-850 3000 5 4 1 FM Approved

HSEF4-10


400 1515 99-174 685-1200 3550 5 4 1 FM Approved

HSEF4-10G


450 1705 54-87 370-600 3000 5 4 1 FM Approved

HSEF4-10G


450 1705 57-125 395-860 3525 5 4 1 FM Approved


7/21/2019 FM guide


HSEF4-10


450 1705 94-106 650-730 2800 5 4 1 FM Approved

HSEF4-10


450 1705 96-121 660-835 3000 5 4 1 FM Approved

HSEF4-10

United

States of America

450 1705 98-173 675-1195 3550 5 4 1 FM Approved

HSEF4-10G


500 1895 48-80 330-550 2950 5 4 1 FM Approved

HSEF4-10


500 1895 95-170 655-1170 3550 5 4 1 FM Approved

HSEF4-10 *


500 1895 90-145 620-1000 3300 5 4 1 FM Approved

HSEF4-10 *


500 1895 95-120 655-825 3000 5 4 1 FM Approved

HSEF4-10 *


500 1895 93-116 640-800 2950 5 4 1 FM Approved

HSEF4-12 *


500 1895 65-111 450-765 2350 5 4 1 FM Approved

HSEF4-12 *


500 1895 50-86 345-595 2100 5 4 1 FM Approved

HSEF4-12 *


500 1895 104-177 715-1220 2950 5 4 1 FM Approved

HSEF4-12 *


500 1895 112-181 770-1250 3000 5 4 1 FM Approved

HSEF4-12 *


500 1895 138-220 950-1515 3300 5 4 1 FM Approved

HSEF4-12 *

UnitedStates of

America

500 1895 160-264 1105-1820 3550 5 4 1 FM Approved

HSUF4-11 *


500 1895 272-446 1875-3075 3550 6 4 2 FM Approved

HSUF4-11 *


500 1895 229-384 1580-2650 3300 6 4 2 FM Approved

HSUF4-11 *


500 1895 183-312 1260-2150 3000 6 4 2 FM Approved

HSUF4-11 *


500 1895 177-300 1220-2070 2950 6 4 2 FM Approved

HSUF4-11 *


500 1895 158-269 1090-1855 2800 6 4 2 FM Approved

HSEF4-10G *

United

States of America

500 1895 50-84 345-580 3000 5 4 1 FM Approved

HSEF4-10G *


500 1895 54-120 370-825 3525 5 4 1 FM Approved

HSEF4-10 *


500 1895 90-100 620-690 2800 5 4 1 FM Approved

HSEF3-9G *


500 1895 125-145 860-1000 3525 4 3 1 FM Approved

HSUF5-7 *


500 1895 173-277 1195-1910 2100 6 5 2 FM Approved

HSUF5-7 *


500 1895 121-190 835-1310 1760 6 5 2 FM Approved


7/21/2019 FM guide


HSEF3-9 *


500 1895 95-130 655-895 3525 4 3 1 FM Approved

HSEF5-14N *


500 1895 50-80 345-550 1760 6 5 1 FM Approved

HSEF6-12 *

United

States of America

500 1895 50-70 345-485 1760 8 6 1 FM Approved

HSEF4-11 *


500 1895 45-60 310-415 1760 5 4 1 FM Approved

HSEF5-11


500 1895 63-115 435-795 2600 6 5 1 FM Approved

HSEF6-16G


500 1895 76-127 525-875 1760 8 6 1 FM Approved

HSEF5-14N


500 1895 93-185 640-1275 2600 6 5 1 FM Approved

HSEF4-11G *


500 1895 39-50 270-345 1760 5 4 1 FM Approved

HSEF5-14 *


500 1895 37-66 255-455 1460 6 5 1 FM Approved

HSEF6-16G


750 2840 69-126 475-870 1760 8 6 1 FM Approved

HSUF4-11 *


750 2840 199-240 1370-1655 2800 6 4 2 FM Approved

HSUF4-11 *


750 2840 227-272 1565-1875 2950 6 4 2 FM Approved

HSUF4-11 *


750 2840 234-286 1615-1970 3000 6 4 2 FM Approved

HSUF4-11 *

UnitedStates of

America

750 2840 295-352 2035-2430 3300 6 4 2 FM Approved

HSUF4-11 *


750 2840 235-417 1620-2875 3550 6 4 2 FM Approved

HSUTF5-16B *


750 2840 183-311 1260-2145 1775 6 5 3 FM Approved

HSEF5-14 *


750 2840 173-180 1195-1240 2400 6 5 1 FM Approved

HSEF5-14 *


750 2840 164-173 1130-1195 2350 6 5 1 FM Approved

HSEF5-12 *


750 2840 184-268 1270-1850 3550 6 5 1 FM Approved

HSEF5-12 *

United

States of America

750 2840 156-234 1075-1615 3300 6 5 1 FM Approved

HSUF5-7 *


750 2840 165-265 1140-1825 2100 6 5 2 FM Approved

HSEF4-12 *


750 2840 147-251 1015-1730 3550 5 4 1 FM Approved

HSEF5-12 *


750 2840 141-186 970-1280 3000 6 5 1 FM Approved

HSEF5-14 *


750 2840 130-138 895-950 2100 6 5 1 FM Approved

HSUF5-7 *


750 2840 101-180 695-1240 1770 6 5 2 FM Approved


7/21/2019 FM guide


7/21/2019 FM guide


HSUHF6-13A2


750 2840 242-370 1670-2550 2950 8 6 2 FM Approved

HSEF5-14 *


1000 3785 165-176 1140-1215 2400 6 5 1 FM Approved

HSEF6-10 *

United

States of America

1000 3785 145-165 1000-1140 3550 8 6 1 FM Approved

HSEF5-14 *


1000 3785 155-167 1070-1150 2350 6 5 1 FM Approved

HSEF5-12 *


1000 3785 128-175 880-1205 2950 6 5 1 FM Approved

HSEF6-16G


1000 3785 68-123 470-850 1760 8 6 1 FM Approved

HSEF5-11 *


1000 3785 95-165 655-1140 3300 6 5 1 FM Approved

HSEF5-8 *


1000 3785 85-100 585-690 3565 6 5 1 FM Approved

HSEF5-11G *


1000 3785 100-195 690-1340 3550 6 5 1 FM Approved

HSEF6-10 *


1000 3785 103-169 710-1165 3550 8 6 1 FM Approved

HSEF6-10 *


1000 3785 101-147 695-1015 3300 8 6 1 FM Approved

HSEF6-10 *


1000 3785 82-121 565-835 3000 8 6 1 FM Approved

HSEF6-10 *


1000 3785 77-114 530-785 2950 8 6 1 FM Approved

HSEF5-11G *

UnitedStates of

America

1000 3785 97-190 670-1310 3500 6 5 1 FM Approved

HSEF5-12 *


1000 3785 170-260 580-1140 3500 6 5 1 FM Approved

HSEF5-12 *


1000 3785 145-222 1000-1530 3300 6 5 1 FM Approved

HSEF5-12 *


1000 3785 132-181 910-1250 3000 6 5 1 FM Approved

HSEF5-12 *


1000 3785 172-262 1185-1805 3550 6 5 1 FM Approved

HSEF5-8 *


1000 3785 89-105 615-725 3550 6 5 1 FM Approved

HSEF5-8G *

United

States of America

1000 3785 65-95 450-655 3565 6 5 1 FM Approved

HSEF6-14 *


1000 3785 40-85 275-585 1760 8 6 1 FM Approved

HSEF6-16 *


1000 3785 55-86 380-595 1460 8 6 1 FM Approved

HSEF5-8N *


1000 3785 60-106 415-730 3550 6 5 1 FM Approved

HSEF6-10 *


1000 3785 70-108 485-745 2800 8 6 1 FM Approved

HSEF6-14G


1000 3785 65-132 450-910 2100 8 6 1 FM Approved


7/21/2019 FM guide


HSEF6-16N *


1000 3785 74-113 510-780 1780 8 6 1 FM Approved

HSEF5-11 *


1000 3785 70-130 485-895 2950 6 5 1 FM Approved

HSEF5-11 *

United

States of America

1000 3785 75-135 515-930 3000 6 5 1 FM Approved

HSEF5-11G *


1000 3785 84-165 580-1140 3300 6 5 1 FM Approved

HSEF6-18 *


1000 3785 119-145 820-1000 1770 8 6 1 FM Approved

HSEF6-18 *


1000 3785 171-205 1180-1415 2100 8 6 1 FM Approved

HSUHF6-13A2


1000 3785 232-362 1600-2495 2950 8 6 2 FM Approved

HSEF6-10 *


1250 4730 65-103 450-710 2800 8 6 1 FM Approved

HSEF6-10 *


1250 4730 97-164 670-1130 3550 8 6 1 FM Approved

HSEF6-12 *


1250 4730 90-169 620-1165 2800 8 6 1 FM Approved

HSEF6-10 *


1250 4730 97-142 670-980 3300 8 6 1 FM Approved

HSEF6-14G


1250 4730 64-130 440-910 2100 8 6 1 FM Approved

HSEF6-14 *


1250 4730 40-82 275-565 1760 8 6 1 FM Approved

HSEF6-16 *

UnitedStates of

America

1250 4730 55-82 380-565 1460 8 6 1 FM Approved

HSEF6-10 *


1250 4730 75-116 515-800 3000 8 6 1 FM Approved

HSEF6-10 *


1250 4730 74-110 510-760 2950 8 6 1 FM Approved

HSEF6-16 *


1250 4730 60-127 415-875 1780 8 6 1 FM Approved

HSEF6-12 *


1250 4730 100-182 690-1255 2950 8 6 1 FM Approved

HSEF6-12 *


1250 4730 104-186 715-1280 3000 8 6 1 FM Approved

HSEF6-18 *

United

States of America

1250 4730 110-145 760-1000 1770 8 6 1 FM Approved

HSEF6-12 *


1250 4730 126-229 870-1580 3300 8 6 1 FM Approved

HSEF6-10 *


1250 4730 142-160 980-1105 3550 8 6 1 FM Approved

HSEF6-12 *


1250 4730 152-273 1050-1880 3550 8 6 1 FM Approved

HSEF6-18 *


1250 4730 165-205 1140-1415 2100 8 6 1 FM Approved

HSUHF6-13A2


1250 4730 283-343 1950-2365 2950 8 6 2 FM Approved


7/21/2019 FM guide


HSEF6-12 *


1500 5680 121-220 835-1515 3300 8 6 1 FM Approved

HSEF6-12 *


1500 5680 120-160 825-1105 2800 8 6 1 FM Approved

HSEF6-12 *

United

States of America

1500 5680 112-180 770-1240 3000 8 6 1 FM Approved

HSEF8-20 *


1500 5680 110-160 760-1105 1780 10 8 1 FM Approved

HSEF6-12 *


1500 5680 108-177 745-1220 2950 8 6 1 FM Approved

HSEF6-10 *


1500 5680 100-136 690-940 3300 8 6 1 FM Approved

HSEF6-10 *


1500 5680 97-160 670-1105 3550 8 6 1 FM Approved

HSEF6-18 *


1500 5680 105-140 725-965 1770 8 6 1 FM Approved

HSEF6-16 *


1500 5680 85-122 585-840 1780 8 6 1 FM Approved

HSEF8-20 *


1500 5680 73-105 505-710 1470 10 8 1 FM Approved

HSEF6-14G *


1500 5680 62-128 430-885 2100 8 6 1 FM Approved

HSEF6-14G *


1500 5680 40-86 275-595 1760 8 6 1 FM Approved

HSEF8-15G *


1500 5680 40-63 275-435 1470 10 8 1 FM Approved

HSEF8-13 *

UnitedStates of

America

1500 5680 40-77 275-530 1760 10 8 1 FM Approved

HSEF6-18 *


1500 5680 160-202 1105-1390 2100 8 6 1 FM Approved

HSEF6-12 *


1500 5680 147-268 1015-1850 3550 8 6 1 FM Approved

HSEF6-10 *


1500 5680 139-155 960-1070 3550 8 6 1 FM Approved

HSEF8-17A *


2000 7570 54-94 370-650 1460 10 8 1 FM Approved

HSEF8-17Q *


2000 7570 55-85 380-585 1470 10 8 1 FM Approved

HSEF8-17W *

United

States of America

2000 7570 90-118 620-815 1780 10 8 1 FM Approved

HSEF8-17W *


2000 7570 110-167 760-1150 2100 10 8 1 FM Approved

HSEF8-13 *


2000 7570 63-74 435-510 1760 10 8 1 FM Approved

HSEF8-15G *


2000 7570 69-130 475-895 2100 10 8 1 FM Approved

HSEF8-15G *


2000 7570 45-89 310-615 1780 10 8 1 FM Approved

HSEF6-14Q *


2000 7570 87-140 600-965 2100 8 6 1 FM Approved


7/21/2019 FM guide


HSEF6-14Q


2000 7570 70-102 485-705 1760 8 6 1 FM Approved

HSEF8-20 *


2000 7570 103-156 710-1015 1780 10 8 1 FM Approved

HSEF8-20G *

United

States of America

2000 7570 110-175 760-1205 1780 10 8 1 FM Approved

HSEF8-20 *


2000 7570 150-212 1035-1460 2100 10 8 1 FM Approved

HSEF8-20G *


2000 7570 72-119 495-820 1470 10 8 1 FM Approved

HSEF8-17 *


2000 7570 54-94 370-650 1460 10 8 1 FM Approved

HSEF8-17V *


2000 7570 110-155 760-1070 2100 10 8 1 FM Approved

HSEF8-17V *


2000 7570 90-105 620-725 1780 10 8 1 FM Approved

HSHF8-26 ††


2000 7570 113-185 780-1275 1470 10 8 1 FM Approved

HSEF8-17 *


2500 9465 65-90 450-620 1460 10 8 1 FM Approved

HSEF8-17 *


2500 9465 80-140 550-965 1780 10 8 1 FM Approved

HSEF10-20*


2500 9465 85-127 585-875 1470 12 10 1 FM Approved

HSEF8-15 *


2500 9465 52-98 360-675 1760 10 8 1 FM Approved

HSEF8-20G *

UnitedStates of

America

2500 9465 104-172 715-1185 1780 10 8 1 FM Approved

HSEF8-20G *


2500 9465 154-202 1060-1395 2100 10 8 1 FM Approved

HSEF8-15A *


2500 9465 105-155 725-1070 2100 10 8 1 FM Approved

HSEF8-17A *


2500 9465 66-90 455-620 1460 10 8 1 FM Approved

HSEF8-17A *


2500 9465 80-137 550-945 1780 10 8 1 FM Approved

HSEF8-17N *


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved

HSEF8-17Q *

United

States of America

2500 9465 80-125 550-860 1780 10 8 1 FM Approved

HSEF8-17Q *


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved

HSEF8-17N *


2500 9465 55-85 380-585 1470 10 8 1 FM Approved

HSEF8-17N *


2500 9465 80-125 550-860 1780 10 8 1 FM Approved

HSHF8-26 ††


2500 9465 107-179 740-1235 1470 10 8 1 FM Approved

HSAF12-19G *


3000 11,355 118-164 815-1130 1760 14 12 1 FM Approved


7/21/2019 FM guide


HSAF12-19G *


3000 11,355 83-117 570-805 1480 14 10 1 FM Approved

HSEF10-20*


3000 11,355 102-210 705-1450 1900 12 10 1 FM Approved

HSEF8-15A *

United

States of America

3000 11,355 100-151 690-1040 2100 10 8 1 FM Approved

HSEF10-16*


3000 11,355 75-123 515-850 1775 12 10 1 FM Approved

HSEF10-16*


3000 11,355 94-142 650-980 1900 12 10 1 FM Approved

HSEF10-20*


3000 11,355 85-188 585-1295 1780 12 10 1 FM Approved

HSHF10-22


3000 11,355 133-159 915-1095 1470 12 10 1 FM Approved

HSHF10-26


3000 11,355 164-223 1130-1540 1480 12 10 1 FM Approved

HSEF10-20*


3500 13,250 120-182 860-1255 1780 12 10 1 FM Approved

HSEF10-16*


3500 13,250 73-120 505-825 1775 12 10 1 FM Approved

HSEF10-16*


3500 13,250 91-140 630-965 1900 12 10 1 FM Approved

HSEF10-20*


3500 13,250 95-206 655-1420 1900 12 10 1 FM Approved

HSAF12-19G *


3500 13,250 80-115 550-795 1480 14 12 1 FM Approved

HSAF12-19G *

UnitedStates of

America

3500 13,250 115-162 795-1115 1760 14 12 1 FM Approved

HSEF10-16*


4000 15,140 100-117 690-805 1775 12 10 1 FM Approved

HSHF10-22


3500 13,250 129-153 890-1055 1470 12 10 1 FM Approved

HSHF10-26


3500 13,250 161-223 1110-1540 1480 12 10 1 FM Approved

HSEF10-16*


4000 15,140 88-139 610-960 1900 12 10 1 FM Approved

HSAF12-19G *


4000 15,140 112-161 770-1110 1760 14 12 1 FM Approved

HSAF12-19G *

United

States of America

4000 15,140 78-112 540-770 1480 14 12 1 FM Approved

HSHF12-26


4000 15,140 166-223 1145-1540 1480 14 12 1 FM Approved

HSEF10-16*


4500 17,035 93-114 640-785 1775 12 10 1 FM Approved

HSEF10-16*


4500 17,035 83-137 570-945 1900 12 10 1 FM Approved

HSAF12-19G *


4500 17,035 109-160 750-1105 1760 14 12 1 FM Approved

HSAF12-19G *


4500 17,035 76-109 525-750 1480 14 12 1 FM Approved


7/21/2019 FM guide


HSHF12-26


4500 17,035 165-220 1140-1515 1480 14 12 1 FM Approved

HSAF12-19G *


5000 18,925 108-157 730-1080 1760 14 12 1 FM Approved

HSHF12-26

United

States of America

5000 18,925 161-218 1110-1505 1480 14 12 1 FM Approved

HSUHF6-18A2


750 2840 222-338 1530-2330 1780 8 6 2 FM Approved

HSUHF6-18A2


1000 3785 209-329 1440-2270 1780 8 6 2 FM Approved

HSUHF6-18A2


1250 4730 196-327 1350-2255 1780 8 6 2 FM Approved

† These pumps are available for operation at any speed within the range shown. The intended operating speed should be specified when the pump is ordered.†† Has special materials for use in nonpotable water applications.* When requested, Peerless can furnish pumps designed for applications where the suction pressures exceed 75 psi (515 kPa). These pumps are designated by the addition of the letter "H" after the type designation.** These pumps are also available in type designations with a "B" suffix indicating an alternate bearing design.

Grundfos A/SCastelo Branco 630, Ave Humberto De Alencar, Sao Bernado Do Campo, São Paulo 09850 300, Brazil





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSF6-16

Brazil 750 2840 54-88 370-605 1450 8 6 1 FM Approved

HSF6-18


HSF6-16


HSF6-18


HSF6-16


HSF6-18


HSF6-18


HSF6-16


HSF6-18


HSF6-18


HSF8-20


HSF8-20G


HSF10-20


HSF6-18


HSF6-18

Brazil 1500 5680 188 1295 2000 8 6 1 FM Approved

HSF8-17


HSF10-20


HSF8-20G


HSF8-20


HSF8-20G


HSF10-16



7/21/2019 FM guide


HSF10-20


HSF8-20G


HSF10-16

Brazil 3000 11,355 46-79 315-545 1450 12 10 1 FM Approved

HSF

10-16 Brazil 3500 13,250 59-76 405-525 1450 12 10 1 FM Approved

Grundfos Pumpenfabrik GmbHWilly-Pelz-Straße 1-5, DE-23812, Wahlstedt, Germany





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSDF2-8 * Germany 250 945 40-100 275-690 3530 3 2 1 FM Approved

HSEF4-10G

Germany 250 945 58-95 400-655 3000 5 4 1 FM Approved

HSEF4-10G


HSEF4-10


HSEF4-10


HSEF4-10


HSEF4-10G


HSEF4-10G


HSEF4-10G


HSEF4-10


HSEF4-10


HSEF4-10G


HSEF4-10G


HSEF4-10


HSEF4-10


HSEF4-10


HSEF4-10G


HSEF4-10G


HSEF4-10


HSEF4-10


HSEF4-10


HSEF4-10G * Germany 500 1895 48-80 330-550 2950 5 4 1 FM Approved

HSEF4-10 * Germany 500 1895 95-170 655-1170 3550 5 4 1 FM Approved





7/21/2019 FM guide


7/21/2019 FM guide



HSUF5-7 * Germany 750 2840 165-265 1140-1825 2100 6 5 2 FM Approved


HSEF

5-12 * Germany 750 2840 141-186 970-1280 3000 6 5 1 FM Approved


HSUF5-7 * Germany 750 2840 101-180 695-1240 1770 6 5 2 FM Approved






HSEF









HSEF



HSEF5-11


HSEF5-14N






HSEF

5-8G *Germany 750 2840 70-100 485-690 3565 6 5 1 FM Approved




HSUHF6-13A2






7/21/2019 FM guide





HSEF









HSEF








HSEF5-8N * Germany 1000 3785 60-106 415-730 3550 6 5 1 FM Approved

HSEF


HSEF6-14G








HSUHF

6-13A2Germany 1000 3785 232-362 1600-2495 2950 8 6 2 FM Approved





HSEF6-14G





7/21/2019 FM guide





HSEF








HSUHF6-13A2


HSEF









HSEF



HSEF6-14G







HSEF

6-10 *Germany 1500 5680 139-155 960-1070 3550 8 6 1 FM Approved

HSEF8-17A * Germany 2000 7570 54-94 370-650 1460 10 8 1 FM Approved

HSEF8-17Q * Germany 2000 7570 55-85 380-585 1470 10 8 1 FM Approved

HSEF8-17W * Germany 2000 7570 90-118 620-815 1780 10 8 1 FM Approved

HSEF8-17W * Germany 2000 7570 110-167 760-1150 2100 10 8 1 FM Approved





7/21/2019 FM guide



HSEF6-14Q



HSEF

8-20G * Germany 2000 7570 110-175 760-1205 1780 10 8 1 FM Approved




HSEF8-17V * Germany 2000 7570 110-155 760-1070 2100 10 8 1 FM Approved

HSEF8-17V * Germany 2000 7570 90-105 620-725 1780 10 8 1 FM Approved

HSHF8-26 †† Germany 2000 7570 113-185 780-1275 1470 10 8 1 FM Approved


HSEF


HSEF10-20* Germany 2500 9465 85-127 585-875 1470 12 10 1 FM Approved







HSEF

8-17N * Germany 2500 9465 115-150 795-1035 2100 10 8 1 FM Approved





HSHF8-26 †† Germany 2500 9465 107-179 740-1235 1470 10 8 1 FM Approved

HSAF12-19G * Germany 3000 11,355 118-164 815-1130 1760 14 12 1 FM Approved


HSEF

10-20*Germany 3000 11,355 102-210 705-1450 1900 12 10 1 FM Approved

HSEF8-15A * Germany 3000 11,355 100-151 690-1040 2100 10 8 1 FM Approved

HSEF10-16* Germany 3000 11,355 75-123 515-850 1775 12 10 1 FM Approved



HSHF10-22

Germany 3000 11,355 133-159 915-1095 1470 12 10 1 FM Approved

HSHF10-26




7/21/2019 FM guide





HSAF

12-19G * Germany 3500 13,250 80-115 550-795 1480 14 12 1 FM Approved



HSHF10-22


HSHF10-26





HSHF

12-26 Germany 4000 15,140 166-223 1145-1540 1480 14 12 1 FM Approved





HSHF12-26



HSHF12-26


HSUHF

6-18A2 Germany 750 2840 222-338 1530-2330 1780 8 6 2 FM Approved

HSUHF6-18A2


HSUHF6-18A2


HSEF4-10


HSEF6-17


HSEF6-17


HSEF6-17


HSEF6-17


HSEF

6-17Germany 1500 5680 102-138 705-950 2100 8 6 1 FM Approved

HSEF6-17


HSEF6-17


HSEF6-17


HSEF8-14


HSEF8-14


HSEF8-14


HSEF8-14



7/21/2019 FM guide


HSEF8-14



ITT Residential & Commercial Water 8200 North Austin Ave, Morton Grove, Illinois 60053, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

8100-3x2x11FSbUnitedStates of America

25 95 46-75 315-515 2100 3 2 1 FM Approved


25 95 41-94 285-650 2350 3 2 1 FM Approved


50 190 46-75 315-515 2100 3 2 1 FM Approved


50 190 41-94 285-650 2350 3 2 1 FM Approved


50 190 63-150 435-1035 2960 3 2 1 FM Approved


50 190 67-155 460-1070 3000 3 2 1 FM Approved


100 380 43-72 295-1200 2100 3 2 1 FM Approved


100 380 37-92 255-635 2350 3 2 1 FM Approved


100 380 62-148 425-1020 2960 3 2 1 FM Approved


100 380 64-152 440-1050 3000 3 2 1 FM Approved


100 380 78-187 540-1290 3300 3 2 1 FM Approved

8100-H3x2x11FSUnitedStates of America

100 380 92-215 635-1480 3550 3 2 1 FM Approved


150 570 83-141 570-970 2960 3 2 1 FM Approved


150 570 86-147 595-1015 3000 3 2 1 FM Approved

8100-3x2x11FSbUnitedStates of

America

150 570 71-183 490-1260 3300 3 2 1 FM Approved


150 570 84-210 580-1450 3550 3 2 1 FM Approved


200 755 114-202 785-1395 3550 3 2 1 FM Approved

8100-8x6x12F aUnitedStates of America

500 1875 40-50 275-345 1485 8 6 1 FM Approved


500 1875 70-102 485-705 2100 8 6 1 FM Approved


500 1875 87-128 600-885 2350 8 6 1 FM Approved


7/21/2019 FM guide


8100-6x4x12F-M aUnitedStates of America

500 1875 109-227 750-1565 2960 6 4 1 FM Approved


500 1875 112-233 770-1605 3000 6 4 1 FM Approved

8100-6x4x12F-M a

United

States of America

500 1895 40-54 275-370 1470 6 4 1 FM Approved


500 1895 40-80 275-550 1770 6 4 1 FM Approved


500 1895 40-49 275-340 1480 8 6 1 FM Approved


500 1895 42-113 290-780 2100 6 4 1 FM Approved


500 1895 43-142 295-980 2350 6 4 1 FM Approved


500 1895 74-148 510-1020 3550 6 4 1 FM Approved


500 1895 63-126 435-870 3300 6 4 1 FM Approved


500 1895 50-101 345-695 3000 6 4 1 FM Approved


500 1895 48-97 330-670 2950 6 4 1 FM Approved


500 1895 57-125 395-860 3300 6 6 1 FM Approved


500 1895 46-102 320-705 3000 6 6 1 FM Approved

8100-6x6x9F aUnitedStates of

America

500 1895 45-98 310-675 2950 6 6 1 FM Approved


500 1895 133-255 915-1760 3555 6 4 1 FM Approved


500 1895 114-220 785-1515 3300 6 4 1 FM Approved


500 1895 123-178 850-1225 3000 6 4 1 FM Approved


500 1895 114-166 785-1145 2900 6 4 1 FM Approved


750 2840 40-48 275-330 1485 8 6 1 FM Approved

8100-8x6x12F a

United

States of America

750 2840 66-100 455-690 2100 8 6 1 FM Approved


750 2840 84-125 580-860 2350 8 6 1 FM Approved


750 2840 100-222 690-1530 2960 6 4 1 FM Approved


750 2840 102-227 705-1565 3000 6 4 1 FM Approved


750 2840 40-48 275-330 1480 8 6 1 FM Approved


750 2840 50-85 345-585 1480 8 6 1 FM Approved


7/21/2019 FM guide



750 2840 40-69 275-475 1770 8 6 1 FM Approved


750 2840 65-136 450-940 2350 6 4 1 FM Approved

8100-6x6x9F a

United

States of America

750 2840 69-134 475-925 3550 6 6 1 FM Approved


750 2840 65-124 450-855 3300 8 6 1 FM Approved


750 2840 52-100 360-690 3000 8 6 1 FM Approved


750 2840 50-96 345-660 2950 8 6 1 FM Approved


750 2840 79-107 545-740 2100 6 4 1 FM Approved


750 2840 100-206 690-1420 3300 6 4 1 FM Approved


750 2840 110-165 760-1140 3000 6 4 1 FM Approved


750 2840 102-152 705-1050 2900 6 4 1 FM Approved


750 2840 119-242 820-1670 3555 6 4 1 FM Approved


1000 3785 40-45 275-310 1480 8 6 1 FM Approved


1000 3785 40-67 275-460 1770 8 6 1 FM Approved


America

1000 3785 45-68 310-470 1780 8 6 1 FM Approved


1000 3785 47-82 325-565 1480 8 6 1 FM Approved


1000 3785 72-122 495-840 1780 8 6 1 FM Approved


1000 3785 47-123 325-850 2350 8 6 1 FM Approved


1000 3785 48-97 330-670 2100 8 6 1 FM Approved


1000 3785 56-100 386-690 2960 8 6 1 FM Approved

8100-8x6x10F a

United

States of America

1000 3785 58-103 400-710 3000 8 6 1 FM Approved


1000 3785 62-97 425-670 2100 8 6 1 FM Approved


1000 3785 81-123 560-850 2350 8 6 1 FM Approved


1000 3785 69-135 475-930 3550 8 6 1 FM Approved


1000 3785 71-126 490-870 3300 8 6 1 FM Approved

8100-6x4x11F bUnitedStates of America

1000 3785 108-197 745-1360 3300 6 4 1 FM Approved


7/21/2019 FM guide



1000 3785 119-162 820-1115 3000 6 4 1 FM Approved


1000 3785 124-156 855-1075 2950 6 4 1 FM Approved

8100-6x4x11F b

United

States of America

1000 3785 130-236 895-1630 3550 6 4 1 FM Approved


1250 4730 40-45 275-310 1470 8 8 1 FM Approved


1250 4730 42-68 290-470 1785 8 8 1 FM Approved


1250 4730 59-95 405-655 2100 8 8 1 FM Approved


1250 4730 75-120 515-825 2350 8 8 1 FM Approved


1250 4730 40-65 275-450 1780 8 6 1 FM Approved


1250 4730 43-120 295-830 2350 8 6 1 FM Approved


1250 4730 45-94 310-650 2100 8 6 1 FM Approved


1250 4730 66-117 455-805 1780 8 6 1 FM Approved


1250 4730 67-120 460-825 3300 8 6 1 FM Approved


1250 4730 78-97 540-670 3000 8 6 1 FM Approved


America

1250 4730 79-141 545-970 3550 8 6 1 FM Approved


1250 4730 87-139 600-960 2900 8 6 1 FM Approved


1250 4730 94-151 650-1040 3000 8 6 1 FM Approved


1250 4730 98-169 675-1165 2100 8 6 1 FM Approved


1250 4730 104-182 715-1255 3300 8 6 1 FM Approved


1250 4730 120-200 825-1380 3500 8 6 1 FM Approved

8100-8x6x18F a

United

States of America

1250 4730 126-215 870-1480 2350 8 6 1 FM Approved


1500 5680 40-66 275-455 1785 8 8 1 FM Approved


1500 5680 57-93 395-640 2100 8 8 1 FM Approved


1500 5680 73-118 505-815 2350 8 8 1 FM Approved


1500 5680 54-115 370-795 2350 8 6 1 FM Approved


1500 5680 57-90 395-620 2100 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 60-128 415-885 1770 8 8 1 FM Approved

8100-10x8x20F cUnitedStates of America

1500 5680 61-108 420-745 1485 10 8 1 FM Approved

8100-8x6x12F-M a

United

States of America

1500 5680 82-135 565-930 2900 8 6 1 FM Approved


1500 5680 88-147 605-1015 3000 8 6 1 FM Approved


1500 5680 100-177 690-1220 3300 8 6 1 FM Approved


1500 5680 119-196 820-1350 3500 8 6 1 FM Approved


1500 5680 120-208 830-1435 2350 8 6 1 FM Approved


1500 5680 123-162 850-1115 2100 8 6 1 FM Approved

8100-12x10x18FaUnitedStates of America

2000 7570 41-93 285-640 1485 12 10 1 FM Approved


2000 7570 55-89 380-615 2100 8 8 1 FM Approved


2000 7570 68-115 470-795 2350 8 8 1 FM Approved


2000 7570 60-128 415-885 1770 10 8 1 FM Approved


2000 7570 67-107 460-740 1485 10 8 1 FM Approved

8100-10x8x20F cUnitedStates of

America

2000 7570 82-183 565-1260 2100 10 8 1 FM Approved


2000 7570 84-100 580-690 1485 10 8 1 FM Approved


2000 7570 85-152 585-1050 1785 10 8 1 FM Approved


2000 7570 107-180 740-1240 2350 10 8 1 FM Approved


2500 9465 53-90 365-620 1485 12 10 1 FM Approved


2500 9465 70-125 485-860 1770 10 8 1 FM Approved

8100-10x8x20F c

United

States of America

2500 9465 95-153 655-1055 1785 10 8 1 FM Approved


2500 9465 96-174 660-1200 2100 10 8 1 FM Approved


2500 9465 100-177 690-1220 2350 10 8 1 FM Approved


2500 9465 172 1185 2350 10 8 1 FM Approved


3000 11,355 70-129 485-890 1785 12 10 1 FM Approved


3000 11,355 82-133 565-915 2100 12 10 1 FM Approved


7/21/2019 FM guide


8200-8x6x14F-L eUnitedStates of America

500 1895 68-166 470-1145 1785 8 6 2 FM Approved

8200-8x6x14F-S eUnitedStates of America

500 1895 73-141 505-970 1785 8 6 2 FM Approved

8200-8x6x18F f

United

States of America

500 1895 102-183 705-1260 1485 8 6 2 FM Approved


500 1895 113-268 780-1850 2350 8 6 2 FM Approved


500 1895 129-295 890-2035 2350 8 6 2 FM Approved


500 1895 144-331 995-2280 2600 8 6 2 FM Approved

8200-8x6x18F f UnitedStates of America

500 1895 152-268 1050-1850 1785 8 6 2 FM Approved


500 1895 160-364 1105-2510 2600 8 6 2 FM Approved


500 1895 192-438 1325-3020 2960 8 6 2 FM Approved


500 1895 197-450 1360-3105 3000 8 6 2 FM Approved


500 1895 210-474 1450-3270 2960 8 6 2 FM Approved


500 1895 215-378 1480-2605 2100 8 6 2 FM Approved


500 1895 216-487 1490-3360 3000 8 6 2 FM Approved

8200-8x6x18F f UnitedStates of

America

500 1895 274-477 1890-3290 2350 8 6 2 FM Approved


500 1895 282-641 1945-4420 3550 8 6 2 FM Approved


500 1895 305-513 2105-3535 3550 8 6 2 FM Approved


750 2840 89-170 615-1170 1485 8 6 2 FM Approved


750 2840 109-154 750-1060 1785 8 6 2 FM Approved


750 2840 138-281 950-1935 2350 8 6 2 FM Approved

8200-8x6x18F f

United

States of America

750 2840 139-256 960-1765 1785 8 6 2 FM Approved


750 2840 143-352 985-2425 2600 8 6 2 FM Approved


750 2840 153-295 1055-2035 2600 8 6 2 FM Approved


750 2840 169-399 1165-2750 2960 8 6 2 FM Approved


750 2840 174-412 1200-2840 3000 8 6 2 FM Approved


750 2840 195-464 1345-3200 2960 8 6 2 FM Approved


7/21/2019 FM guide



750 2840 200-476 1380-3280 3000 8 6 2 FM Approved


750 2840 201-364 1385-2510 2100 8 6 2 FM Approved

8200-8x6x18F f

United

States of America

750 2840 258-461 1780-3180 2350 8 6 2 FM Approved


750 2840 259-601 1785-4145 3550 8 6 2 FM Approved


750 2840 290-502 2000-3460 3550 8 6 2 FM Approved


1000 3785 169-238 1165-1640 1785 8 6 2 FM Approved


1000 3785 183-346 1260-2385 2100 8 6 2 FM Approved


1000 3785 188-264 1295-1820 2350 8 6 2 FM Approved


1000 3785 200-334 1380-2305 2600 8 6 2 FM Approved


1000 3785 214-446 1475-3075 2960 8 6 2 FM Approved


1000 3785 220-458 1515-3160 3000 8 6 2 FM Approved


1000 3785 240-443 1655-3055 2350 8 6 2 FM Approved


2000 7570 123-182 850-1255 1770 12 8 1 FM Approved


America

2500 9465 114-173 785-1195 1770 12 8 1 FM Approved


2500 9465 85-138 585-950 1485 12 8 1 FM Approved


2500 9465 128-208 882-1434 1785 12 8 1 FM Approved


3000 11,355 123-199 850-1372 1780 12 8 1 FM Approved


3500 13,250 95-169 655-1165 1770 14 10 1 FM Approved

9100-14x10x20FdUnitedStates of America

4000 15,140 90-165 620-1140 1770 14 10 1 FM Approved

9100-14x10x20F-Ld

United

States of America

4500 17,035 100-189 690-1305 1785 14 10 1 FM Approved

9100-14x10x20F-Ld


5000 18,925 97-186 670-1280 1785 14 10 1 FM Approved

9100-16x12x23FgUnitedStates of America

3000 11,355 53-114 365-785 1480 16 12 1 FM Approved


3500 13,250 50-113 345-780 1480 16 12 1 FM Approved


4000 15,140 47-112 325-770 1480 16 12 1 FM Approved


4500 17,030 60-110 415-760 1480 16 12 1 FM Approved


7/21/2019 FM guide



5000 18,925 56-108 385-745 1480 16 12 1 FM Approved


3000 11,355 53-183 365-1260 1485 16 12 1 FM Approved

9100-16x12x23Fg

United

States of America

3500 13,250 50-182 345-1255 1485 16 12 1 FM Approved


4000 15,140 47-182 325-1255 1485 16 12 1 FM Approved


4500 17,030 60-182 415-1255 1485 16 12 1 FM Approved


5000 18,925 56-181 385-1250 1485 16 12 1 FM Approved

a This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 375 psi (2585 kPa).b This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 400 psi (2760 kPa).c This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 370 psi (2550 kPa).d This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 280 psi (1930 kPa).e This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 800 psi (5515 kPa).f This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 500 psi (3445 kPa).g This model is available with an "H" preceding the type designation indicating a max allowable discharge pressure of 289 psi (1995 kPa).

J-Line Pump Company, DBA as American-Marsh Pumps185 Progress Rd, Collierville, Tennessee 38017-2719, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

10x14-20FP-HD


2500 9465 61-65 421-448 1100 14 10 1 FM Approved

10x14-20FP-HD


3000 11,355 61-65 421-448 1100 14 10 1 FM Approved

10x14-20FP-HD


3000 11,355 106-112 731-772 1450 14 10 1 FM Approved

10x14-20FP-HD


3500 13,250 60-64 414-441 1100 14 10 1 FM Approved

10x14-20FP-HD


3500 13,250 106-112 731-772 1450 14 10 1 FM Approved

10x14-20FP-HD


4000 15,140 106-111 731-765 1450 14 10 1 FM Approved

2.5x3-10FP-HD


250 945 100-110 690-760 2900 3 2 1/2 1 FM Approved

2.5x3-10FP-HD


300 1135 98-110 675-760 2900 3 2 1/2 1 FM Approved

2.5x3-10FP-HD


250 945 146-163 1005-1125 3500 3 2 1/2 1 FM Approved

2.5x3-10FP-HD


300 1135 145-161 1000-1110 3500 3 2 1/2 1 FM Approved

2.5x3-10FP-HD


400 1515 140-154 965-1060 3500 3 2 1/2 1 FM Approved

3x4-10FP-HD


250 945 96-106 660-730 2900 4 3 1 FM Approved

3x4-10FP-HD


300 1135 95-105 655-725 2900 4 3 1 FM Approved

3x4-10FP-HD


400 1515 93-103 640-710 2900 4 3 1 FM Approved


7/21/2019 FM guide


3x4-10FP-HD


400 1515 136-149 940-1025 3500 4 3 1 FM Approved

3x4-10FP-HD


500 1895 134-147 925-1015 3500 4 3 1 FM Approved

4x5-18FP-HD

United

States of America

450 1705 102-126 703-869 1760 5 4 1 FM Approved

4x5-18FP-HD


500 1895 100-126 689-869 1760 5 4 1 FM Approved

4x5-18FP-HD


400 1515 102-126 703-869 1760 5 4 1 FM Approved

4x6-10FP-HD


500 1895 87-114 600-785 2900 6 4 1 FM Approved

4x6-10FP-HD


500 1895 126-166 870-1145 3500 6 4 1 FM Approved

4x6-10FP-HD


750 2840 122-160 840-1105 3500 6 4 1 FM Approved

5x6-10FP-HD


500 1895 96-115 660-795 2900 6 5 1 FM Approved

5x6-10FP-HD


750 2840 93-111 640-765 2900 6 5 1 FM Approved

5x6-10FP-HD


1000 3785 89-108 615-745 2900 6 5 1 FM Approved

5x6-10FP-HD


1250 4730 84 580 2900 6 5 1 FM Approved

5x6-10FP-HD


500 1895 139-163 960-1125 3500 6 5 1 FM Approved

5x6-10FP-HD

UnitedStates of

America

750 2840 136-162 940-1115 3500 6 5 1 FM Approved

5x6-10FP-HD


1000 3785 132-156 910-1075 3500 6 5 1 FM Approved

5x6-11FP-HD


500 1895 116-167 800-1150 2900 6 5 1 FM Approved

5x6-11FP-HD


750 2840 116-166 800-1145 2900 6 5 1 FM Approved

5x6-11FP-HD


500 1895 169-238 1165-1640 3500 6 5 1 FM Approved

5x6-11FP-HD


750 2840 188-237 1295-1635 3500 6 5 1 FM Approved

5x6-12FP-HK

United

States of America

500 1895 374-482 2580-3325 3500 6 5 2 FM Approved

5x6-12bFP-HK


500 1895 287-373 1980-2570 2900 6 5 2 FM Approved

5x6-15FP-HD


750 2840 204-280 1405-1930 2900 6 5 1 FM Approved

5x6-15FP-HD


1000 3785 197-277 1360-1910 2900 6 5 1 FM Approved

5x6-15FP-HD


500 1895 45-67 310-462 1450 6 5 1 FM Approved

5x6-15FP-HD


750 2840 70-100 483-689 1760 6 5 1 FM Approved


7/21/2019 FM guide


5x8-18FP-HD


1250 4730 125-174 862-1200 1760 8 5 1 FM Approved

5x8-18FP-HD


750 2840 88-118 607-814 1450 8 5 1 FM Approved

5x8-18FP-HD

United

States of America

750 2840 130-178 896-1227 1760 8 5 1 FM Approved

5x8-18FP-HD


1000 3780 85-116 586-800 1450 8 5 1 FM Approved

5x8-18FP-HD


1000 3780 129-178 889-1227 1760 8 5 1 FM Approved

6x8-18FP-HD


1000 3780 86-114 593-786 1450 8 6 1 FM Approved

6x8-18FP-HD


1500 5680 121-162 834-1117 1760 8 6 1 FM Approved

6x8-18FP-HD


1000 3780 127-168 876-1158 1760 8 6 1 FM Approved

6x8-18FP-HD


750 2840 88-115 607-793 1450 8 6 1 FM Approved

6x8-18FP-HD


1250 4730 85-112 586-772 1450 8 6 1 FM Approved

6x8-18FP-HD


1250 4730 124-166 855-1144 1760 8 6 1 FM Approved

6x8-22FP-HD


1000 3780 77-88 531-607 1100 8 6 1 FM Approved

6x8-22FP-HD


1500 5680 138-151 951-1041 1450 8 6 1 FM Approved

6x8-22FP-HD

UnitedStates of

America

1000 3780 142-155 979-1068 1450 8 6 1 FM Approved

6x8-22FP-HD


1250 4730 75-86 517-593 1100 8 6 1 FM Approved

6x8-22FP-HD


1250 4730 142-153 979-1055 1450 8 6 1 FM Approved

6x8-22FP-HD


1500 5680 72-83 496-572 1100 8 6 1 FM Approved

8x10-18FP-HD


2000 7570 139-172 958-1186 1760 10 8 1 FM Approved

8x10-18FP-HD


1250 4730 96-117 662-807 1450 10 8 1 FM Approved

8x10-18FP-HD

United

States of America

2500 9465 133-168 917-1158 1760 10 8 1 FM Approved

8x10-18FP-HD


1500 5680 94-117 648-807 1450 10 8 1 FM Approved

8x10-18FP-HD


1500 5680 142-172 979-1186 1760 10 8 1 FM Approved

8x10-18FP-HD


2000 7570 90-115 621-793 1450 10 8 1 FM Approved

8x12-21FP-HD


1500 5680 67-79 462-545 1100 12 8 1 FM Approved

8x12-21FP-HD


2500 9465 120-136 827-938 1450 12 8 1 FM Approved


7/21/2019 FM guide


8x12-21FP-HD


2000 7570 123-139 848-958 1450 12 8 1 FM Approved

8x12-21FP-HD


2000 7570 65-77 448-531 1100 12 8 1 FM Approved

Kirloskar Brothers LimitedKirloskarvadi – 416 308, Dist. Sangli, Maharashtra, India





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

FH06SC† India 1500 5680 95-172 655-1185 2950 8 6 1 FM Approved

FH08QE†** India 1500 5680 111-166 765-114 1900-2300 10 8 1 FM Approved


FH08SA† India 2000 7570 91-164 625-1130 1475 10 8 1 FM Approved

FH08SB† India 2000 7570 94-150 650-1035 1475 10 8 1 FM Approved





FH08SA† India 2500 9465 85-161 585-1110 1475 10 8 1 FM Approved



FH08SE India 2500 9465 183 1262 1490 10 8 1 FM Approved

FH10TD India 2500 9465 195-265 1345-1825 1480 12 10 1 FM Approved

FH08SE India 3000 11,355 179 1234 1490 10 8 1 FM Approved

FH12RD† India 3000 11,355 108-165 745-1140 1780 16 12 1 FM Approved


FH12RC† India 3000 11,355 142-178 980-1225 1780 16 12 1 FM Approved


FH08SC† India 3000 11,355 135-162 930-1115 1475 10 8 1 FM Approved

FH08QE†** India 3000 11,355 120-150 825-1035 2100-2300 10 8 1 FM Approved

FH10TD India 3000 11,355 187-256 1290-1765 1480 12 10 1 FM Approved

FH10SE India 3000 11,355 109-187 750-1290 1760 12 10 1 FM Approved





FH12SA† India 3500 13,250 135-202 931-1393 1490 16 12 1 FM Approved




















FR08BD India 300 1135 93-145 640-1000 3550 4 3 1 FM Approved


7/21/2019 FM guide






FR08BE India 500 1895 54-104 370-715 3550 4 3 1 FM Approved






FR10DE India 200 755 109-187 750-1290 3100 5 4 1 FM Approved

















FR10EA India 750 2840 136-213 940-1470 2950 5 4 1 FM Approved

FR10EA India 500 1895 144-219 995-1510 2950 5 4 1 FM Approved

FR10ED India 500 1895 135-255 930-1760 2950 5 4 1 FM Approved


























FR12BF India 1250 4730 98-132 675-910 3550 6 5 1 FM Approved

FR12BF India 1000 3785 104-144 715-995 3550 6 5 1 FM Approved

FR12CF India 500 1895 43-49 295-340 1760 6 5 1 FM Approved





7/21/2019 FM guide







FR12CG India 1000 3785 119-175 820-1205 3550 6 5 1 FM Approved





FR12DF India 1000 3785 134-199 925-1370 3550 6 5 1 FM Approved












FR12EE India 750 2840 146-264 1005-1820 3000 6 5 1 FM Approved




















FR12XD India 500 1895 256-330 1765-2275 2950 6 5 2 FM Approved

FR12XD India 750 2840 230-300 1585-2070 2950 6 5 2 FM Approved

FR12YD India 500 1895 145-191 1000-1317 1760 6 5 2 FM Approved














FR15DF India 1000 3785 102 705 2300 8 6 1 FM Approved




7/21/2019 FM guide



















FR15FE India 1250 4730 134-225 925-1550 2200 8 6 1 FM Approved


















FR15XE India 1000 3785 254-346 1750-2385 2950 8 6 2 FM Approved




FR15XF India 1250 4730 246-348 1695-2400 2950 8 6 2 FM Approved




FR15YE India 1250 4730 214-274 1475-1890 2100 8 6 2 FM Approved



















7/21/2019 FM guide


7/21/2019 FM guide


100-250AF Australia 750 2840 47-83 324-572 2350 6 4 1 FM Approved













125-290AF Australia 1250 4730 58 400 1750 8 5 1 FM Approved









150-460AF Australia 2000 7570 99 683 1750 8 6 1 FM Approved






200-520AF Australia 3000 11,355 135 931 1450 10 8 1 FM Approved

200-520AF Australia 3000 11,355 134 924 1750 10 8 1 FM Approved

OMEGA100-310A

Australia 500 1895 162-216 1115-1490 2900 6 4 1 FM Approved

OMEGA100-310A


OMEGA100-310A


OMEGA100-310A


KSB Bombas HidraulicsSA Rua Jose Rabelo Portela, 400 13220-000, Varzea Paulista, SP Brazil





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

Omega80-270 * Brazil 150 570 40-52 275-360 1750 5 3 1 FM Approved

Omega

80-270 *Brazil 200 755 40-51 275-350 1750 5 3 1 FM Approved









7/21/2019 FM guide





Omega

80-270 * Brazil 300 1135 40-72 275-495 2100 5 3 1 FM Approved

Omega80-270 * Brazil 300 1135 48 330 1750 5 3 1 FM Approved







Omega









Omega


RDL150-500


RDL150-500


RDL150-500


RDL150-500


RDL150-500


RDL200-500†


RDL200-500†


RDL200-500†


RDL200-500†


RDL200-500†


RDL200-500†


RDL200-500†



7/21/2019 FM guide


RDL200-500†


RDL200-500†


RDL

200-500† Brazil 2500 9465 148-192 1020-1325 1760 10 8 1 FM Approved

RDL200-620


RDL200-620


RDL200-620


* This model is available with an "M" in the type designation indicating mechanical seals.† These pumps are available with special materials for use in nonpotable water applications, this is indicated with an "F" in the t ype designation.

KSB Compania Sudamericana De Bombas SAAv Ader 3625, 1607 Carapachay, Provincia De Buenos Aires, Argentina





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

RDL250-500

Argentina 2500 9465 91-143 627-986 1450 12 10 1 FM Approved

RDL250-500

Argentina 3000 11,355 89-142 614-979 1450 12 10 1 FM Approved

RDL250-500


RDL250-500


RDL250-500


RDL250-500


RDL200-500


RDL200-500 Argentina 2000 9465 120-132 827-910 1450 10 8 1 FM Approved

RDL150-310


RDL150-310


RDL150-310


Mark Grundfos LtdaAv Humberto de Alencar, Castelo Branco, 630 09850, 300 Sao Bernardo do Campo, SP Brazil





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSF6-12


HSF6-12


HSF6-12


HSF6-16


HSF6-18


HSF5-11


HSF5-11



7/21/2019 FM guide


HSF6-16

Brazil 1000 3785 50-86 345-595 1450 8 6 - FM Approved

HSF6-18


HSF6-16


HSF

6-12 Brazil 1000 3785 109-191 750-1315 2900 8 6 1 FM Approved

HSF6-18


HSF6-12


HSF6-18


HSF6-16


HSF6-12


HSF6-18


HSF6-12


HSF


HSF8-20


HSF8-20G


HSF10-20


HSF6-18


HSF6-12


HSF6-12


HSF6-18


HSF


HSF10-20


HSF8-20G


HSF8-20


HSF8-20G


HSF10-16


HSF10-20


HSF8-20G


HSF

10-16Brazil 3000 11,355 46-79 315-545 1450 12 10 1 FM Approved

HSF10-16

Brazil 3500 13,250 59-76 405-525 1450 12 10 1 FM Approved

National Fire Fighting Mfg FZCOBox 17014, Jebel Ali Free Zone, Dubai, United Arab Emirates





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

NF-S-125-80United ArabEmirates

750 2840 236 1625 2900 5 3 1 FM Approved


7/21/2019 FM guide



750 2840 108-216 745-1490 2900 6 4 1 FM Approved


1000 3785 101-215 695-1485 2900 6 4 1 FM Approved

NF-S-150-100-375

United

ArabEmirates

750 2840 227-280 1565-1930 2900 6 4 1 FM Approved

NF-S-150-100-375United ArabEmirates

1000 3785 215-273 1485-1880 2900 6 4 1 FM Approved


1000 3785 143-252 985-1735 2900 8 5 1 FM Approved


1250 4730 134-250 925-1725 2900 8 5 1 FM Approved


1500 5680 121-242 835-1670 2900 8 5 1 FM Approved

Nijhuis Pompen BVParallelweg, Box 102, 7100 AC Winterswijk, The Netherlands





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HGT1-100.250 Netherlands 500 1895 76-139 525-960 2960 5 4 1 FM Approved








HGT1-125.315 Netherlands 750 2840 100-218 690-1505 2960 6 5 1 FM ApprovedHGT1-125.315 Netherlands 750 2840 88-138 605-950 2400 6 5 1 FM Approved



HG1-125.500 Netherlands 750 2840 99-130 685-905 1480 6 5 1 FM Approved







HGT1-150.400A Netherlands 1250 4730 90-128 620-880 1750 8 6 1 FM Approved



HGT1-150.315 Netherlands 1500 5680 76-130 525-895 2400 8 6 1 FM ApprovedHGT1-150.315 Netherlands 1500 5680 68-127 470-875 2300 8 6 1 FM Approved














7/21/2019 FM guide








HGT1-200.500B Netherlands 2000 7570 98-160 675-1105 1490 10 8 1 FM Approved








HGT1-250.500 * Netherlands 2500 9465 85-138 585-950 1495 12 10 1 FM Approved






HGT1-250.400 Netherlands 3000 11,355 64-126 440-870 1750 12 10 1 FM Approved

HGT1-250.500 * Netherlands 3000 11,355 81-136 560-940 1496 12 10 1 FM Approved






HGT1-300.400A Netherlands 3500 13,250 88-129 605-890 1780 14 12 1 FM Approved









HGTI-300.400 Netherlands 4500 17,035 78-133 540-915 1780 14 12 1 FM Approved

HGTI-300.500 Netherlands 4500 17,035 98-152 675-1050 1495 14 12 1 FM Approved







* These pumps available with alternate materials of construction for use in nonpotable water applications.

Patterson Pump Co Sub Gorman-Rupp CoBox 790, Toccoa, Georgia 30577, USA

Note: Standard construction includes ASA 125 suction and discharge flanges. For ASA 250 discharge flanges, suffix H is added to type designations.





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

10x8 M **UnitedStates of America

2000 7570 65-152 450-1050 1760 10 8 1 FM Approved


2000 7570 70-106 485-730 1500 10 8 1 FM Approved


2000 7570 135-214 930-1475 2100 10 8 1 FM Approved


7/21/2019 FM guide



2500 9465 100-150 690-1035 1770 10 8 1 FM Approved


2500 9465 135-210 930-1450 2100 10 8 1 FM Approved

10x8x17SSC

United

States of America

2000 7570 74-121 510-835 1750 10 8 1 FM Approved

10x8x17SSC


2000 7570 78-127 540-875 1785 10 8 1 FM Approved

10x8x17SSC


1500 5680 55-86 380-595 1475 10 8 1 FM Approved

10x8x17SSC


2000 7570 115-168 795-1160 2100 10 8 1 FM Approved

10x8x17SSC


1500 5680 53-84 365-580 1450 10 8 1 FM Approved

10x8x17SSC


2000 7570 67-91 460-630 1450 10 8 1 FM Approved

10x8x17SSC


2500 9465 97-132 670-910 1750 10 8 1 FM Approved

10x8x17SSC


2500 9465 104-139 715-960 1785 10 8 1 FM Approved

10x8x17SSC


2000 7570 71-95 490-655 1475 10 8 1 FM Approved

10x8x17SSC


2500 9465 150-186 1035-1280 2100 10 8 1 FM Approved

10x8x23ASSC


1500 5680 134-201 925-1385 1500 10 8 1 FM Approved

10x8x23ASSC

UnitedStates of

America

1500 5680 138-285 950-1960 1780 10 8 1 FM Approved

10x8x23ASSC


1500 5680 129-193 890-1330 1470 10 8 1 FM Approved

10x8x23ASSC


2000 7570 119-188 820-1295 1470 10 8 1 FM Approved

10x8x23ASSC


2000 7570 125-197 860-1360 1500 10 8 1 FM Approved

10x8x23ASSC


2000 7570 127-282 875-1935 1780 10 8 1 FM Approved

12x10MAA


2500 9465 77-144 530-995 1770 12 10 1 FM Approved

12x8 MAA *

United

States of America

2000 7570 67-173 460-1195 1500 12 8 1 FM Approved

12x8 MAA *UnitedStates of America

2500 9465 91-169 625-1165 1500 12 8 1 FM Approved


2000 7570 64-164 440-1130 1470 12 8 1 FM Approved


1500 5680 71-175 490-1205 1500 12 8 1 FM Approved


2500 9465 88-160 605-1105 1470 12 8 1 FM Approved


1500 5680 68-168 470-1160 1470 12 8 1 FM Approved


7/21/2019 FM guide



3000 11,355 106-177 730-1220 1470 12 8 1 FM Approved


3000 11,355 80-180 550-1240 1750 12 8 1 FM Approved

12x8 MAA *

United

States of America

3500 13,250 102-172 705-1185 1470 12 8 1 FM Approved


3500 13,250 89-188 615-1295 1750 12 8 1 FM Approved


3500 13,250 115-174 795-1200 1470 12 8 1 FM Approved


4000 15,140 98-188 675-1295 1750 12 8 1 FM Approved


4000 15,140 140-167 965-1150 1470 12 8 1 FM Approved

16x12x21SSC*


4000 15,140 69-141 475-970 1470 16 12 1 FM Approved

16x12x21SSC*


3500 13,250 106-212 730-1460 1780 16 12 1 FM Approved

16x12x21SSC*


4000 15,140 103-211 710-1455 1780 16 12 1 FM Approved

16x12x21SSC*


3500 13,250 71-144 490-995 1470 16 12 1 FM Approved

16x12x21SSC*


4500 17,035 66-137 455-945 1470 16 12 1 FM Approved

16x12x21SSC*


4500 17,035 101-208 695-1435 1780 16 12 1 FM Approved

16x12x21SSC*

UnitedStates of

America

5000 18,925 107-132 740-910 1470 16 12 1 FM Approved

16x12x21SSC*


5000 18,925 108-204 745-1405 1780 16 12 1 FM Approved

16x12x26ASSC *


3500 13,250 153-229 1055-1580 1475 16 12 1 FM Approved

16x12x26ASSC *


3500 13,250 265 1825 1770 16 12 1 FM Approved

16x12x26ASSC *


4500 17,035 256 1765 1770 16 12 1 FM Approved

16x12x26ASSC *


4000 15,140 147-223 1015-1540 1475 16 12 1 FM Approved

16x12x26ASSC *

United

States of America

4000 15,140 262 1805 1770 16 12 1 FM Approved

16x12x26ASSC *


5000 18,925 253 1745 1770 16 12 1 FM Approved

16x12x26ASSC *


5000 18,925 161-209 1110-1440 1475 16 12 1 FM Approved

16x12x26ASSC *


4500 17,035 140-218 965-1505 1475 16 12 1 FM Approved

18x14MAB*


5500 20,820 120-164 825-1130 1470 18 14 1 FM Approved

18x14MAB*


6000 22,710 118-163 815-1125 1470 18 14 1 FM Approved


7/21/2019 FM guide


18x14MAB*


6500 24,605 115-161 795-1110 1470 18 14 1 FM Approved

18x14MAB*


7000 26,500 112-158 770-1090 1470 18 14 1 FM Approved

3x2 MN

United

States of America

150 570 45-109 310-750 3500 3 2 1 FM Approved

3x2 MNUnitedStates of America

200 755 40-104 275-715 3500 3 2 1 FM Approved

4x3 DMDUnitedStates of America

500 1895 118-200 815-1380 1770 4 3 2 FM Approved

4x3 MEUnitedStates of America

500 1895 40-100 275-690 1750 4 3 1 FM Approved


500 1895 170-200 1170-1380 2800 5 3 2 FM Approved


500 1895 155-227 1105-1565 2950 5 3 2 FM Approved


500 1895 165-235 1140-1620 3000 5 3 2 FM Approved


500 1895 189-337 1305-2325 3550 5 3 2 FM Approved


500 1895 198-280 1365-1930 3300 5 3 2 FM Approved

5x3 MACUnitedStates of America

500 1895 43-105 295-725 3300 5 3 1 FM Approved


500 1895 40-122 275-840 3550 5 3 1 FM Approved

5x4 MUnitedStates of

America

750 2840 40-70 275-485 1750 5 4 1 FM Approved

5x4 MUnitedStates of America

750 2840 100 690 2500 5 4 1 FM Approved


500 1895 40-88 275-605 2950 5 4 1 FM Approved


750 2840 82-105 565-725 3300 5 4 1 FM Approved


750 2840 63-123 435-850 3550 5 4 1 FM Approved


500 1895 41-91 280-625 3000 5 4 1 FM Approved

5x4x12SSC

United

States of America

500 1895 106-168 730-1160 2800 5 4 1 FM Approved

5x4x12SSC


1000 3785 198-284 1365-1960 3550 5 4 1 FM Approved

5x4x12SSC


500 1895 122-186 840-1280 2950 5 4 1 FM Approved

5x4x12SSC


750 2840 75-179 515-1235 2800 5 4 1 FM Approved

5x4x12SSC


500 1895 126-191 870-1315 3000 5 4 1 FM Approved

5x4x12SSC


500 1895 138-272 950-1875 3550 5 4 1 FM Approved


7/21/2019 FM guide


5x4x12SSC


1000 3785 130-188 895-1295 2950 5 4 1 FM Approved

5x4x12SSC


750 2840 78-294 540-2025 3550 5 4 1 FM Approved

5x4x12SSC

United

States of America

750 2840 85-200 585-1380 2950 5 4 1 FM Approved

5x4x12SSC


750 2840 88-151 605-1040 2600 5 4 1 FM Approved

5x4x12SSC


750 2840 88-207 605-1425 3000 5 4 1 FM Approved

5x4x12SSC


1000 3785 136-195 940-1345 3000 5 4 1 FM Approved

5x4x12SSC


750 2840 105-172 725-1185 2950 5 4 1 FM Approved

5x4x12SSC


750 2840 109-177 750-1220 3000 5 4 1 FM Approved

5x4x12SSC


750 2840 118-262 815-1805 3550 5 4 1 FM Approved

5x4x12ADMD


1000 3785 270-298 1860-2055 2600 5 4 2 FM Approved

5x4x12ADMD


1000 3785 290-355 2000-2450 2800 5 4 2 FM Approved

5x4x12ADMD


1000 3785 272-396 1875-2730 2960 5 4 2 FM Approved

5x4x12ADMD


500 1895 309-332 2130-2290 2600 5 4 2 FM Approved

5x4x12ADMD

UnitedStates of

America

500 1895 327-386 2255-2660 2800 5 4 2 FM Approved

5x4x12ADMD


500 1895 303-422 2090-2910 2960 5 4 2 FM Approved

5x4x12ADMD


750 2840 296-323 2040-2225 2600 5 4 2 FM Approved

5x4x12ADMD


750 2840 315-379 2170-2615 2800 5 4 2 FM Approved

5x4x12ADMD


750 2840 285-419 1965-2890 2960 5 4 2 FM Approved

5x4x12ADMD


750 2840 397-600 2735-4135 3560 5 4 2 FM Approved

5x4x12ADMD

United

States of America

1000 3785 368-578 2535-3985 3560 5 4 2 FM Approved

5x4x12BDMD


500 1895 247-389 1705-2680 2960 5 4 2 FM Approved

5x4x12BDMD


500 1895 338-565 2330-3895 3560 5 4 2 FM Approved

5x4x12BDMD


500 1895 216-297 1490-2050 2600 5 4 2 FM Approved

5x4x12BDMD


750 2840 190-270 1310-1860 2600 5 4 2 FM Approved

5x4x12BDMD


750 2840 199-321 1370-2215 2800 5 4 2 FM Approved


7/21/2019 FM guide


5x4x12BDMD


750 2840 216-364 1490-2510 2960 5 4 2 FM Approved

5x4x12BDMD


750 2840 310-540 2135-3725 3560 5 4 2 FM Approved

5x4x12BDMD

United

States of America

500 1895 227-347 1565-2390 2800 5 4 2 FM Approved

6x3 HWUnitedStates of America

750 2840 252-394 1735-2715 3560 6 3 2 FM Approved


1250 4730 184 1270 1780 6 5 1 FM Approved


500 1895 295-362 2035-2495 2100 6 5 2 FM Approved


750 2840 150-216 1035-1490 1760 6 5 2 FM Approved


750 2840 177-238 1220-1640 1770 6 5 2 FM Approved


750 2840 199-234 1370-1615 1780 6 5 2 FM Approved


750 2840 203-338 1400-2330 2100 6 5 2 FM Approved


750 2840 278-350 1915-2415 2100 6 5 2 FM Approved


1000 3785 252-332 1740-2290 2100 6 5 2 FM Approved


500 1895 216-279 1490-1925 2100 6 5 2 FM Approved

6x5 DMDUnitedStates of

America

1000 3785 152-232 1050-1600 1770 6 5 2 FM Approved


1000 3785 55-125 380-860 1770 6 5 1 FM Approved


750 2840 60-133 415-915 1760 6 5 1 FM Approved


1000 3785 100 690 2450 6 5 1 FM Approved


500 1895 82-135 565-930 1775 6 5 1 FM Approved

6x5 MAAUnitedStates of America

750 2840 83-123 570-850 3000 6 5 1 FM Approved

6x5 MAA

United

States of America

500 1895 114-156 785-1075 3300 6 5 1 FM Approved


500 1895 62-126 425-870 2950 6 5 1 FM Approved


500 1895 65-131 450-905 3000 6 5 1 FM Approved


1000 3785 100 690 3550 6 5 1 FM Approved


500 1895 100-182 690-1255 3550 6 5 1 FM Approved


750 2840 79-119 545-820 2950 6 5 1 FM Approved


7/21/2019 FM guide



750 2840 100-180 690-1240 3550 6 5 1 FM Approved


1000 3785 112-165 770-1140 3550 6 5 1 FM Approved

6x5 MAA

United

States of America

750 2840 106-150 730-1035 3300 6 5 1 FM Approved

6x5x11ASSC *


1250 4730 98-152 675-1050 2950 6 5 1 FM Approved

6x5x11ASSC *


1000 3785 81-164 560-1130 2950 6 5 1 FM Approved

6x5x11ASSC *


1000 3785 64-122 440-840 2600 6 5 1 FM Approved

6x5x11BSSC *


1250 4730 113-208 780-1435 3560 6 5 1 FM Approved

6x5x11BSSC *


1000 3785 72-145 495-1000 2950 6 5 1 FM Approved

6x5x14SSC


750 2840 100-270 690-1860 3000 6 5 1 FM Approved

6x5x14SSC


750 2840 84-128 580-885 2100 6 5 1 FM Approved

6x5x14SSC


750 2840 54-163 370-1125 2350 6 5 1 FM Approved

6x5x14SSC


750 2840 84-234 580-1615 2800 6 5 1 FM Approved

6x5x14SSC


1000 3785 165-225 1140-1550 2800 6 5 1 FM Approved

6x5x14SSC

UnitedStates of

America

1000 3790 87-255 600-1760 2950 6 5 1 FM Approved

6x5x14SSC


1250 4730 152-216 1050-1490 2800 6 5 1 FM Approved

6x5x14SSC


1250 4730 145-238 1000-1640 2950 6 5 1 FM Approved

6x5x14SSC


750 2840 173-233 1195-1605 2800 6 5 1 FM Approved

6x5x14SSC


1250 4730 151-247 1040-1705 3000 6 5 1 FM Approved

6x5x14SSC


1000 3790 89-265 615-1825 3000 6 5 1 FM Approved

6x5x14SSC

United

States of America

1000 3785 151-227 1040-1565 2800 6 5 1 FM Approved

6x5x14SSC


750 2840 54-84 370-580 1750 6 5 1 FM Approved

6x5x14SSC


750 2840 56-88 385-605 1780 6 5 1 FM Approved

6x5x14SSC


1000 3785 98-155 675-1070 2350 6 5 1 FM Approved

6x5x14SSC


750 2840 95-260 655-1795 2950 6 5 1 FM Approved

6x5x17SSC


750 2840 40-64 275-440 1475 6 5 1 FM Approved


7/21/2019 FM guide


6x5x17SSC


750 2840 48-82 325-570 1450 6 5 1 FM Approved

6x5x17SSC


750 2840 50-87 345-600 1475 6 5 1 FM Approved

6x5x17SSC

United

States of America

500 1895 63-97 435-685 1775 6 5 1 FM Approved

6x5x17SSC


500 1895 80-146 550-1000 1775 6 5 1 FM Approved

6x5x17SSC


750 2840 58-92 400-635 1750 6 5 1 FM Approved

6x5x17SSC


750 2840 73-134 505-925 1750 6 5 1 FM Approved

6x5x17SSC


750 2840 59-95 405-655 1775 6 5 1 FM Approved

6x5x17SSC


750 2840 75-140 515-950 1775 6 5 1 FM Approved

6x5x17SSC


1000 3785 55-90 370-620 1775 6 5 1 FM Approved

6x5x17SSC


1000 3785 68-129 470-890 1775 6 5 1 FM Approved

6x5x17SSC


1000 3785 66-125 450-850 1750 6 5 1 FM Approved

6x5x17SSC


1000 3785 53-86 360-595 1750 6 5 1 FM Approved

6x5x17SSC


500 1895 41-66 285-450 1450 6 5 1 FM Approved

6x5x17SSC

UnitedStates of

America

500 1895 43-68 295-470 1475 6 5 1 FM Approved

6x5x17SSC


500 1895 53-91 365-625 1450 6 5 1 FM Approved

6x5x17SSC


500 1895 55-93 370-640 1475 6 5 1 FM Approved

6x5x17SSC


500 1895 61-95 420-655 1750 6 5 1 FM Approved

6x5x17SSC


500 1895 77-142 530-970 1750 6 5 1 FM Approved

6x5x17SSC


750 2840 40-61 275-420 1450 6 5 1 FM Approved

8x6 MAA

United

States of America

1500 5680 127-203 875-1400 3570 8 6 1 FM Approved

8x6 MABSUnitedStates of America

1250 4730 102-136 705-940 1780 8 6 1 FM Approved


1250 4730 157-217 1080-1495 2350 8 6 1 FM Approved


1500 5680 94-122 650-840 1750 8 6 1 FM Approved


1500 5680 98-127 675-875 1780 8 6 1 FM Approved


1500 5680 100-125 690-860 1750 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 145-210 1000-1450 2350 8 6 1 FM Approved


1250 4730 99-131 685-905 1750 8 6 1 FM Approved

8x6 MI

United

States of America

1250 4730 74-108 510-745 1775 8 6 1 FM Approved

8x6 MIUnitedStates of America

1500 5680 104-154 715-1060 2100 8 6 1 FM Approved


1250 4730 42-112 290-770 1750 8 6 1 FM Approved


1500 5680 69-162 475-1115 2100 8 6 - FM Approved


1500 5680 70-111 485-765 1780 8 6 1 FM Approved


1250 4730 43-69 295-475 1775 8 6 1 FM Approved


1500 5680 40-69 275-475 1760 8 6 1 FM Approved


1500 5680 49-107 340-740 1750 8 6 1 FM Approved


1500 5680 51-67 350-460 1775 8 6 1 FM Approved


1250 4730 50-116 345-800 1780 8 6 1 FM Approved


1250 4730 74-164 510-1130 2100 8 6 1 FM Approved

8x6 MIUnitedStates of

America

1500 5680 59-106 405-730 1750 8 6 1 FM Approved


1500 5680 61-109 420-750 1775 8 6 1 FM Approved


1250 4730 62-109 425-750 1750 8 6 1 FM Approved


1500 5680 69-101 475-695 1750 8 6 1 FM Approved


1500 5680 70-100 485-690 1760 8 6 1 FM Approved


1500 5680 71-105 490-725 1775 8 6 1 FM Approved

8x6 MI

United

States of America

1250 4730 65-112 450-770 1775 8 6 1 FM Approved


1250 4730 72-104 495-715 1750 8 6 1 FM Approved

8x6 MJUnitedStates of America

1000 3785 40-50 275-345 1760 8 6 1 FM Approved

8x6 YRUnitedStates of America

1250 4730 100-156 690-1075 3000 8 6 1 FM Approved


750 2840 110-171 760-1180 3000 8 6 1 FM Approved


1500 5680 99-142 685-980 3000 8 6 1 FM Approved


7/21/2019 FM guide



1000 3785 100-165 690-1140 3000 8 6 1 FM Approved

8x6 YSUnitedStates of America

2000 7570 95-141 655-970 2100 8 6 1 FM Approved

8x6 YS

United

States of America

2000 7570 89-100 615-690 1780 8 6 1 FM Approved

8x6 YSUnitedStates of America

2500 9465 110-131 760-905 2100 8 6 1 FM Approved

8x6x12SSC


1500 5680 117-144 805-995 2800 8 6 1 FM Approved

8x6x12SSC


1250 4730 141-267 970-1840 3575 8 6 1 FM Approved

8x6x12SSC


1250 4730 82-102 565-705 2350 8 6 1 FM Approved

8x6x12SSC


1500 5680 133-164 920-1130 2950 8 6 1 FM Approved

8x6x12SSC


1250 4730 90-175 620-1205 2950 8 6 1 FM Approved

8x6x12SSC


1250 4730 79-155 545-1070 2800 8 6 1 FM Approved

8x6x12SSC


1500 5680 139-214 960-1475 3300 8 6 1 FM Approved

8x6x12SSC


1500 5680 168-256 1160-1765 3575 8 6 1 FM Approved

8x6x12SSC


1250 4730 118-224 815-1545 3300 8 6 1 FM Approved

* These pumps available with special materials for use in nonpotable water applications.** This model is available with an "I" preceding the type designation indicating alternate materials of construction.

Patterson Pump Ireland LimitedUnit 14, Mullingar Business Park, County Westmeath, Mullingar, Ireland

Note: Standard construction includes ASA 125 suction and discharge flanges. For ASA 250 discharge flanges, suffix H is added to type designations.





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

3x2 MN Ireland 150 570 45-109 310-750 3500 3 2 1 FM Approved

3x2 MN Ireland 200 755 40-104 275-715 3500 3 2 1 FM Approved

5x4 MAC Ireland 500 1895 40-88 275-605 2950 5 4 1 FM Approved

4x3 ME Ireland 500 1895 40-100 275-690 1750 4 3 1 FM Approved

6x5x17 SSC Ireland 500 1895 41-66 285-450 1450 6 5 1 FM Approved











6x5 MAA Ireland 500 1895 62-126 425-870 2950 6 5 1 FM Approved


6x5 M Ireland 500 1895 82-135 565-930 1775 6 5 1 FM Approved


7/21/2019 FM guide





4x3 DMD Ireland 500 1895 118-200 815-1380 1770 4 3 2 FM Approved




































5x4 M Ireland 750 2840 100 690 2500 5 4 1 FM Approved





8x6 YR Ireland 750 2840 110-171 760-1180 3000 8 6 1 FM Approved







6x3 HW Ireland 750 2840 252-394 1735-2715 3560 6 3 2 FM Approved

8x6 MJ Ireland 1000 3785 40-50 275-345 1760 8 6 1 FM Approved










7/21/2019 FM guide



6x5 M Ireland 1000 3785 100 690 2450 6 5 1 FM Approved

6x5 MAA Ireland 1000 3785 100 690 3550 6 5 1 FM Approved








8x6 MI Ireland 1250 4730 42-67 290-460 1750 8 6 1 FM Approved









8x6 MABS Ireland 1250 4730 99-131 685-905 1750 8 6 1 FM Approved









6x5 DMD Ireland 1250 4730 184 1270 1780 6 5 1 FM Approved




10x8x17SSC

Ireland 1500 5680 53-84 365-580 1450 10 8 1 FM Approved

10x8x17SSC




















10x8x17SSC


10x8x17SSC


10x8x17SSC


10x8x17SSC




7/21/2019 FM guide



8x6 YS Ireland 2000 7570 89-100 615-690 1780 8 6 1 FM Approved


10x8x17SSC Ireland 2000 7570 115-168 795-1160 2100 10 8 1 FM Approved






10x8x17SSC


10x8x17SSC




10x8x17SSC Ireland 2500 9465 150-186 1035-1280 2100 10 8 1 FM Approved

12x8 MAA Ireland 3000 11,355 106-177 730-1220 1470 12 8 1 FM Approved





Peerless Pump Company2005 Dr Martin Luther King Jr St, Indianapolis, Indiana 46206, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

10AEF16 *UnitedStates of America

3000 11,355 75-123 515-850 1775 12 10 1 FM Approved


3000 11,355 94-142 650-980 1900 12 10 1 FM Approved

10AEF16 * UnitedStates of America

3500 13,250 73-120 505-825 1775 12 10 1 FM Approved


3500 13,250 91-140 630-965 1900 12 10 1 FM Approved


4000 15,140 100-117 690-805 1775 12 10 1 FM Approved


4000 15,140 88-139 610-960 1900 12 10 1 FM Approved


4500 17,035 93-114 640-785 1775 12 10 1 FM Approved

10AEF16 *UnitedStates of

America

4500 17,035 83-137 570-945 1900 12 10 1 FM Approved


3500 13,250 95-206 655-1420 1900 12 10 1 FM Approved


3000 11,355 85-188 585-1295 1780 12 10 1 FM Approved


3500 13,250 120-182 860-1255 1780 12 10 1 FM Approved


2500 9465 85-127 585-875 1470 12 10 1 FM Approved


3000 11,355 102-210 705-1450 1900 12 10 1 FM Approved


7/21/2019 FM guide


10AHF22UnitedStates of America

3500 13,250 129-153 890-1055 1470 12 10 1 FM Approved


3000 11,355 133-159 915-1095 1470 12 10 1 FM Approved

10AHF26

United

States of America

3500 13,250 161-223 1110-1540 1480 12 10 1 FM Approved


3000 11,355 164-223 1130-1540 1480 12 10 1 FM Approved

12AF19G *UnitedStates of America

3500 13,250 80-115 550-795 1480 14 12 1 FM Approved


3500 13,250 115-162 795-1115 1760 14 12 1 FM Approved


4000 15,140 112-161 770-1110 1760 14 12 1 FM Approved


4000 15,140 78-112 540-770 1480 14 12 1 FM Approved


3000 11,355 118-164 815-1130 1760 14 12 1 FM Approved


3000 11,355 83-117 570-805 1480 14 10 1 FM Approved


4500 17,035 109-160 750-1105 1760 14 12 1 FM Approved


4500 17,035 76-109 525-750 1480 14 12 1 FM Approved


5000 18,925 108-157 730-1080 1760 14 12 1 FM Approved

12AHF26UnitedStates of

America

4500 17,035 165-220 1140-1515 1480 14 12 1 FM Approved


4000 15,140 166-223 1145-1540 1480 14 12 1 FM Approved


5000 18,925 161-218 1110-1505 1480 14 12 1 FM Approved

12HFY20CUnitedStates of America

3000 11,355 97-121 670-835 1480 16 12 1 FM Approved


3000 11,355 142-178 980-1225 1780 16 12 1 FM Approved


4000 15,140 139-174 960-1200 1780 16 12 1 FM Approved

12HFY20C

United

States of America

4500 17,035 91-116 625-800 1480 16 12 1 FM Approved


4500 17,035 136-172 940-1185 1780 16 12 1 FM Approved


4000 15,140 94-118 650-815 1480 16 12 1 FM Approved


3500 13,250 141-176 970-1215 1780 16 12 1 FM Approved


3500 13,250 96-119 660-820 1480 16 12 1 FM Approved

12HFY20DUnitedStates of America

3000 11,355 72-113 495-780 1480 16 12 1 FM Approved


7/21/2019 FM guide



4500 17,035 63-105 435-725 1480 16 12 1 FM Approved


4000 15,140 66-108 455-745 1480 16 12 1 FM Approved

12HFY20D

United

States of America

4500 17,035 99-158 685-1090 1780 16 12 1 FM Approved


3500 13,250 69-111 475-765 1480 16 12 1 FM Approved


3000 11,355 108-165 745-1140 1780 16 12 1 FM Approved


3500 13,250 105-163 725-1125 1780 16 12 1 FM Approved


4000 15,140 102-161 705-1110 1780 16 12 1 FM Approved

12HYF20DUnitedStates of America

3000 11,355 72-113 495-780 1480 16 12 1 FM Approved


3500 13,250 69-111 475-765 1480 16 12 1 FM Approved


3500 13,250 105-163 725-1125 1780 16 12 1 FM Approved


4500 17,035 63-105 435-725 1480 16 12 1 FM Approved


4500 17,035 99-158 685-1090 1780 16 12 1 FM Approved


3000 11,355 108-165 745-1140 1780 16 12 1 FM Approved

12HYF20DUnitedStates of

America

4000 15,140 66-108 455-745 1480 16 12 1 FM Approved


5000 18,925 95-154 640-1065 1780 16 12 1 FM Approved


4000 15,140 102-161 705-1110 1780 16 12 1 FM Approved

12HYF25AUnitedStates of America

4000 15,140 131-199 903-1372 1490 16 12 1 FM Approved


5000 18,925 122-193 841-1331 1490 16 12 1 FM Approved


3500 13,250 135-202 931-1393 1490 16 12 1 FM Approved

12HYF25A

United

States of America

4500 17,035 126-196 869-1351 1490 16 12 1 FM Approved

2ADF8 *UnitedStates of America

250 945 40-100 275-690 3530 3 2 1 FM Approved

3ABF9 *UnitedStates of America

500 1895 95-125 655-860 3550 4 3 1 FM Approved


500 1895 95-130 655-895 3525 4 3 1 FM Approved

3AEF9G *UnitedStates of America

500 1895 125-145 860-1000 3525 4 3 1 FM Approved

3THF9UnitedStates of America

500 1890 81-133 560-915 3550 4 3 1 FM Approved


7/21/2019 FM guide



400 1515 87-139 600-960 3550 4 3 1 FM Approved


200 755 96-149 660-1025 3550 4 3 1 FM Approved

3THF9

United

States of America

250 945 94-147 650-1015 3550 4 3 1 FM Approved


300 1135 93-145 640-1000 3550 4 3 1 FM Approved


750 2840 100-109 690-750 3000 5 4 1 FM Approved


750 2840 70-115 485-795 1760 6 4 1 FM Approved

4AEF10UnitedStates of America

300 1135 100-174 690-1200 3550 5 4 1 FM Approved


250 945 100-125 690-860 3000 5 4 1 FM Approved


750 2840 83-93 570-640 2800 5 4 1 FM Approved


750 2840 86-110 595-760 3000 5 4 1 FM Approved


750 2840 82-139 565-960 3300 5 4 1 FM Approved


750 2840 84-164 580-1130 3550 5 4 1 FM Approved


750 2840 80-159 550-1095 3500 5 4 1 FM Approved


America

750 2840 83-107 570-740 2950 5 4 1 FM Approved


400 1515 96-107 660-740 2800 5 4 1 FM Approved


400 1515 98-123 665-850 3000 5 4 1 FM Approved


400 1515 99-174 685-1200 3550 5 4 1 FM Approved


450 1705 94-106 650-730 2800 5 4 1 FM Approved


450 1705 96-121 660-835 3000 5 4 1 FM Approved

4AEF10

United

States of America

450 1705 98-173 675-1195 3550 5 4 1 FM Approved


500 1895 95-170 655-1170 3550 5 4 1 FM Approved


500 1895 90-145 620-1000 3300 5 4 1 FM Approved


500 1895 95-120 655-825 3000 5 4 1 FM Approved


500 1895 93-116 640-800 2950 5 4 1 FM Approved


250 945 100-175 690-1205 3550 5 4 1 FM Approved


7/21/2019 FM guide



250 945 97-108 670-745 2800 5 4 1 FM Approved


300 1135 100-125 690-860 3000 5 4 1 FM Approved

4AEF10

United

States of America

500 1895 90-100 620-690 2800 5 4 1 FM Approved

4AEF10GUnitedStates of America

250 945 58-95 400-655 3000 5 4 1 FM Approved


300 1135 97-108 670-745 2800 5 4 1 FM Approved


250 945 61-132 420-910 3525 5 4 1 FM Approved


500 1895 50-84 345-580 3000 5 4 1 FM Approved


500 1895 54-120 370-825 3525 5 4 1 FM Approved


450 1705 54-87 370-600 3000 5 4 1 FM Approved


450 1705 57-125 395-860 3525 5 4 1 FM Approved


300 1135 58-93 400-640 3000 5 4 1 FM Approved


400 1515 55-90 380-620 3000 5 4 1 FM Approved


400 1515 59-128 405-885 3525 5 4 1 FM Approved

4AEF10G *UnitedStates of

America

500 1895 48-80 330-550 2950 5 4 1 FM Approved


300 1135 61-130 420-895 3525 5 4 1 FM Approved


750 2840 40-56 275-385 1760 5 4 1 FM Approved


500 1895 45-60 310-415 1760 5 4 1 FM Approved


500 1895 39-50 270-345 1760 5 4 1 FM Approved


500 1895 65-111 450-765 2350 5 4 1 FM Approved

4AEF12 *

United

States of America

500 1895 50-86 345-595 2100 5 4 1 FM Approved


750 2840 147-251 1015-1730 3550 5 4 1 FM Approved


750 2840 125-207 860-1425 3300 8 6 1 FM Approved


750 2840 95-164 655-1130 2950 5 4 1 FM Approved


750 2840 100-170 690-1170 3000 5 4 1 FM Approved


500 1895 104-177 715-1220 2950 5 4 1 FM Approved


7/21/2019 FM guide



500 1895 112-181 770-1250 3000 5 4 1 FM Approved


500 1895 138-220 950-1515 3300 5 4 1 FM Approved

4AEF12 *

United

States of America

500 1895 160-264 1105-1820 3550 5 4 1 FM Approved

4AF12-C *UnitedStates of America

500 1895 168-210 1160-1450 3550 6 4 1 FM Approved


750 2840 95-129 655-890 3550 6 4 1 FM Approved


500 1890 102-139 705-960 3550 6 4 1 FM Approved


400 1515 105-144 725-995 3550 6 4 1 FM Approved


400 1515 134-205 925-1415 3550 5 4 1 FM Approved


500 1895 86-158 595-1090 2950 5 4 1 FM Approved


500 1895 97-176 670-1215 3100 5 4 1 FM Approved


300 1135 106-185 730-1275 3100 5 4 1 FM Approved


500 1890 129-200 890-1380 3550 5 4 1 FM Approved


300 1135 138-208 950-1435 3550 5 4 1 FM Approved

4THF12UnitedStates of

America

250 945 139-209 960-1440 3550 5 4 1 FM Approved


200 755 140-210 965-1450 3550 5 4 1 FM Approved


250 945 97-168 670-1160 2950 5 4 1 FM Approved


400 1515 92-164 635-1130 2950 5 4 1 FM Approved


300 1135 96-167 660-1150 2950 5 4 1 FM Approved


250 945 108-186 745-1280 3100 5 4 1 FM Approved

4THF12

United

States of America

200 755 109-187 750-1290 3100 5 4 1 FM Approved


400 1515 102-182 705-1255 3100 5 4 1 FM Approved


200 755 98-169 675-1165 2950 5 4 1 FM Approved


750 2840 136-213 940-1470 2950 5 4 1 FM Approved


500 1895 144-219 995-1510 2950 5 4 1 FM Approved


750 2840 82-108 565-745 2100 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 77-149 530-1025 2400 5 4 1 FM Approved


750 2840 69-137 475-945 2300 5 4 1 FM Approved

4THF15

United

States of America

750 2840 62-122 425-840 2200 5 4 1 FM Approved


500 1895 72-137 495-945 2200 5 4 1 FM Approved


500 1895 131-247 905-1705 2900 5 4 1 FM Approved


500 1895 135-255 930-1760 2950 5 4 1 FM Approved


500 1895 141-264 970-1820 3000 5 4 1 FM Approved


500 1895 87-162 600-1115 2400 5 4 1 FM Approved


500 1895 96-176 660-1215 2500 5 4 1 FM Approved


500 1895 65-122 450-840 2100 5 4 1 FM Approved


500 1895 81-150 560-1035 2300 5 4 1 FM Approved


500 1895 104-193 715-1330 2600 5 4 1 FM Approved


750 2840 131-252 905-1735 3000 5 4 1 FM Approved


America

750 2840 124-243 855-1675 2950 5 4 1 FM Approved


750 2840 121-233 835-1605 2900 5 4 1 FM Approved


750 2840 112-216 770-1490 2800 5 4 1 FM Approved


500 1895 121-229 835-1580 2800 5 4 1 FM Approved


750 2840 94-179 650-1235 2600 5 4 1 FM Approved


750 2840 85-164 585-1130 2500 5 4 1 FM Approved

4TUF11 *

United

States of America

500 1895 177-300 1220-2070 2950 6 4 2 FM Approved

4TUF11 *UnitedStates of America

500 1895 158-269 1090-1855 2800 6 4 2 FM Approved


500 1895 272-446 1875-3075 3550 6 4 2 FM Approved


500 1895 229-384 1580-2650 3300 6 4 2 FM Approved


500 1895 183-312 1260-2150 3000 6 4 2 FM Approved


750 2840 199-240 1370-1655 2800 6 4 2 FM Approved


7/21/2019 FM guide



750 2840 227-272 1565-1875 2950 6 4 2 FM Approved


750 2840 234-286 1615-1970 3000 6 4 2 FM Approved

4TUF11 *

United

States of America

750 2840 295-352 2035-2430 3300 6 4 2 FM Approved


750 2840 235-417 1620-2875 3550 6 4 2 FM Approved


500 1895 63-115 435-795 2600 6 5 1 FM Approved


750 2840 65-123 450-850 2800 6 5 1 FM Approved


1000 3785 95-165 655-1140 3300 6 5 1 FM Approved


1000 3785 70-130 485-895 2950 6 5 1 FM Approved


1000 3785 75-135 515-930 3000 6 5 1 FM Approved


750 2840 58-112 400-770 2600 6 5 1 FM Approved


1000 3785 97-190 670-1310 3500 6 5 1 FM Approved


1000 3785 84-165 580-1140 3300 6 5 1 FM Approved


1000 3785 100-195 690-1340 3550 6 5 1 FM Approved


America

750 2840 156-234 1075-1615 3300 6 5 1 FM Approved


1000 3785 170-260 580-1140 3500 6 5 1 FM Approved


1000 3785 145-222 1000-1530 3300 6 5 1 FM Approved


1000 3785 132-181 910-1250 3000 6 5 1 FM Approved


1000 3785 172-286 1185-1970 3550 6 5 1 FM Approved


750 2840 184-289 1270-1995 3550 6 5 1 FM Approved

5AEF12 *

United

States of America

1000 3785 128-175 880-1205 2950 6 5 1 FM Approved


750 2840 141-186 970-1280 3000 6 5 1 FM Approved


750 2840 136-180 940-1240 2950 6 5 1 FM Approved


500 1895 37-66 255-455 1460 6 5 1 FM Approved


750 2840 50-94 345-650 1760 6 5 1 FM Approved


1000 3785 165-176 1140-1215 2400 6 5 1 FM Approved


7/21/2019 FM guide



1000 3785 155-167 1070-1150 2350 6 5 1 FM Approved


750 2840 130-138 895-950 2100 6 5 1 FM Approved

5AEF14 *

United

States of America

750 2840 173-180 1195-1240 2400 6 5 1 FM Approved


750 2840 164-173 1130-1195 2350 6 5 1 FM Approved

5AEF14NUnitedStates of America

750 2840 86-181 595-1250 2600 6 5 1 FM Approved

5AEF14N *UnitedStates of America

500 1895 50-80 345-550 1760 6 5 1 FM Approved

5AEF14NUnitedStates of America

500 1895 93-185 640-1275 2600 6 5 1 FM Approved


750 2840 55-78 380-540 3000 6 5 1 FM Approved


750 2840 70-96 485-660 3300 6 5 1 FM Approved


750 2840 60-106 415-730 3500 6 5 1 FM Approved


750 2840 60-111 415-765 3550 6 5 1 FM Approved


750 2840 60-105 415-725 3565 6 5 1 FM Approved


1000 3785 89-105 615-725 3550 6 5 1 FM Approved


America

1000 3785 85-100 585-690 3565 6 5 1 FM Approved


750 2840 54-75 370-515 2950 6 5 1 FM Approved


750 2840 70-100 485-690 3565 6 5 1 FM Approved


1000 3785 65-95 450-655 3565 6 5 1 FM Approved


750 2840 47-67 325-460 2950 6 5 1 FM Approved


750 2840 48-70 330-485 3000 6 5 1 FM Approved

5AEF8N *

United

States of America

1000 3785 60-106 415-730 3550 6 5 1 FM Approved


500 1890 112-148 770-1020 3550 6 5 1 FM Approved


750 2840 106-144 730-990 3550 6 5 1 FM Approved


1000 3785 99-137 680-945 3550 6 5 1 FM Approved


750 2840 111-199 765-1370 3550 6 5 1 FM Approved


750 2840 74-134 510-925 2950 6 5 1 FM Approved


7/21/2019 FM guide



500 1890 118-208 815-1435 3550 6 5 1 FM Approved

5THF11GUnitedStates of America

750 2840 130-185 895-1275 3550 6 5 1 FM Approved

5THF11G

United

States of America

1000 3785 119-175 820-1205 3550 6 5 1 FM Approved


750 2840 111-142 765-980 2950 6 5 1 FM Approved


1000 3785 100-131 690-905 2950 6 5 1 FM Approved


500 1890 138-193 950-1330 3550 6 5 1 FM Approved


750 2840 141-208 970-1435 3550 6 5 1 FM Approved


1000 3785 89-159 615-1095 2950 6 5 1 FM Approved


750 2840 95-165 655-1140 2950 6 5 1 FM Approved


1250 4730 82-148 565-1020 2950 6 5 1 FM Approved


1250 4730 125-191 860-1315 3550 6 5 1 FM Approved


1000 3785 134-199 925-1370 3550 6 5 1 FM Approved


500 1895 80-143 550-985 2200 6 5 1 FM Approved


America

750 2840 70-134 485-925 2200 6 5 1 FM Approved


750 2840 105-193 725-1330 2600 6 5 1 FM Approved


750 2840 97-178 670-1225 2500 6 5 1 FM Approved


500 1895 72-131 495-905 2100 6 5 1 FM Approved


500 1895 104-187 715-1290 2500 6 5 1 FM Approved


500 1895 87-158 600-1090 2300 6 5 1 FM Approved

5THF15

United

States of America

1000 3785 159-213 1095-1470 2800 6 5 1 FM Approved


1000 3785 134-250 925-1725 3000 6 5 1 FM Approved


750 2840 90-121 620-835 2100 6 5 1 FM Approved


1000 3785 132-181 910-1250 2600 6 5 1 FM Approved


1000 3785 128-240 885-1655 2950 6 5 1 FM Approved


1000 3785 123-232 850-1600 2900 6 5 1 FM Approved


7/21/2019 FM guide



750 2840 88-162 605-1115 2400 6 5 1 FM Approved


750 2840 124-227 855-1565 2800 6 5 1 FM Approved

5THF15

United

States of America

750 2840 146-264 1005-1820 3000 6 5 1 FM Approved


750 2840 141-255 970-1760 2950 6 5 1 FM Approved


500 1895 97-171 670-1180 2400 6 5 1 FM Approved


750 2840 78-148 540-1020 2300 6 5 1 FM Approved


750 2840 136-245 940-1690 2900 6 5 1 FM Approved


750 2840 101-180 695-1240 1770 6 5 2 FM Approved


500 1895 121-190 835-1310 1760 6 5 2 FM Approved


500 1895 173-277 1195-1910 2100 6 5 2 FM Approved


750 2840 165-265 1140-1825 2100 6 5 2 FM Approved

5TUTF16B *UnitedStates of America

750 2840 183-311 1260-2145 1775 6 5 3 FM Approved

5TXF12UnitedStates of America

500 1895 256-330 1765-2275 2950 6 5 2 FM Approved

5TYF16UnitedStates of

America

750 2840 240-312 1655-2151 2300 6 5 2 FM Approved

5TYF16UnitedStates of America

750 2840 230-300 1585-2070 2950 6 5 2 FM Approved


750 2840 190-250 1310-1724 2100 6 5 2 FM Approved


750 2840 163-200 1124-1379 1900 6 5 2 FM Approved


500 1895 260-334 1793-2303 2300 6 5 2 FM Approved


500 1895 273-350 1882-2413 2350 6 5 2 FM Approved

5TYF16

United

States of America

500 1895 173-223 1193-1538 1900 6 5 2 FM Approved


500 1895 145-191 1000-1317 1760 6 5 2 FM Approved


750 2840 250-328 1724-2262 2350 6 5 2 FM Approved


1000 3785 101-147 695-1015 3300 8 6 1 FM Approved


1250 4730 142-160 980-1105 3550 8 6 1 FM Approved


1500 5680 100-136 690-940 3300 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 97-160 670-1105 3550 8 6 1 FM Approved


1500 5680 139-155 960-1070 3550 8 6 1 FM Approved

6AEF10 *

United

States of America

1000 3785 70-108 485-745 2800 8 6 1 FM Approved


1000 3785 82-121 565-835 3000 8 6 1 FM Approved


1000 3785 77-114 530-785 2950 8 6 1 FM Approved


1000 3785 145-165 1000-1140 3550 8 6 1 FM Approved


1250 4730 65-103 450-710 2800 8 6 1 FM Approved


1250 4730 97-164 670-1130 3550 8 6 1 FM Approved


1250 4730 97-142 670-980 3300 8 6 1 FM Approved


1250 4730 75-116 515-800 3000 8 6 1 FM Approved


1250 4730 74-110 510-760 2950 8 6 1 FM Approved


1000 3785 103-169 710-1165 3550 8 6 1 FM Approved


1500 5680 108-177 745-1220 2950 8 6 1 FM Approved


America

1250 4730 100-182 690-1255 2950 8 6 1 FM Approved


750 2840 47-71 325-490 1760 8 6 1 FM Approved


1500 5680 147-268 1015-1850 3550 8 6 1 FM Approved


500 1895 50-70 345-485 1760 8 6 1 FM Approved


1250 4730 104-186 715-1280 3000 8 6 1 FM Approved


1250 4730 126-229 870-1580 3300 8 6 1 FM Approved

6AEF12 *

United

States of America

1250 4730 90-169 620-1165 2800 8 6 1 FM Approved


1250 4730 152-273 1050-1880 3550 8 6 1 FM Approved


1500 5680 121-220 835-1515 3300 8 6 1 FM Approved


1500 5680 120-160 825-1105 2800 8 6 1 FM Approved


1500 5680 112-180 770-1240 3000 8 6 1 FM Approved


1000 3785 40-85 275-585 1760 8 6 1 FM Approved


7/21/2019 FM guide



1250 4730 40-82 275-565 1760 8 6 1 FM Approved


1250 4730 64-130 440-910 2100 8 6 1 FM Approved

6AEF14G

United

States of America

1500 5680 62-128 430-885 2100 8 6 1 FM Approved


1500 5680 40-86 275-595 1760 8 6 1 FM Approved


1000 3785 65-132 450-910 2100 8 6 1 FM Approved

6AEF14QUnitedStates of America

2000 7570 70-102 485-705 1760 8 6 1 FM Approved

6AEF14Q *UnitedStates of America

2000 7570 87-140 600-965 2100 8 6 1 FM Approved


1250 4730 60-127 415-875 1780 8 6 1 FM Approved


1000 3785 55-86 380-595 1460 8 6 1 FM Approved


1500 5680 85-122 585-840 1780 8 6 1 FM Approved


1250 4730 55-82 380-565 1460 8 6 1 FM Approved


500 1895 76-127 525-875 1760 8 6 1 FM Approved


750 2840 69-126 475-870 1760 8 6 1 FM Approved

6AEF16G *UnitedStates of

America

1000 3785 68-123 470-850 1760 8 6 1 FM Approved


1000 3785 74-113 510-780 1780 8 6 1 FM Approved


1000 3785 76-111 525-765 1760 8 6 1 FM Approved


1250 4730 71-99 490-685 1760 8 6 1 FM Approved


1000 3785 114-163 785-1125 2100 8 6 1 FM Approved


1250 4730 109-152 750-1050 2100 8 6 1 FM Approved

6AEF17

United

States of America

1500 5680 102-138 705-950 2100 8 6 1 FM Approved


1000 3785 146-210 1005-1450 2350 8 6 1 FM Approved


1250 4730 140-201 965-1385 2350 8 6 1 FM Approved


1500 5680 130-185 895-1275 2350 8 7 1 FM Approved


1500 5680 105-140 725-965 1770 8 6 1 FM Approved


1250 4730 110-145 760-1000 1770 8 6 1 FM Approved


7/21/2019 FM guide



1250 4730 165-205 1140-1415 2100 8 6 1 FM Approved


1000 3785 119-145 820-1000 1770 8 6 1 FM Approved

6AEF18 *

United

States of America

1500 5680 160-202 1105-1390 2100 8 6 1 FM Approved


1000 3785 171-205 1180-1415 2100 8 6 1 FM Approved


1250 4730 100-150 690-1035 2970 8 6 1 FM Approved


750 2840 95-135 655-930 2450-3000 8 6 1 FM Approved


750 2840 100-150 690-1035 2970 8 6 1 FM Approved


1000 3785 93-130 640-895 2450-3000 8 6 1 FM Approved


1000 3785 100-150 690-1035 2970 8 6 1 FM Approved


1250 4730 87-130 600-895 2450-3000 9 6 1 FM Approved

6HYF12CUnitedStates of America

2000 7570 125-162 860-1115 2950 8 6 1 FM Approved

6HYF12CUnitedStates of America

1500 5680 95-172 655-1185 2950 8 6 1 FM Approved


1000 3785 102 705 2300 8 6 1 FM Approved


America

1250 4730 137-191 945-1315 3550 8 6 1 FM Approved


1000 3785 90-157 620-1080 2800 8 6 1 FM Approved


1000 3785 102 705 2300 8 6 1 FM Approved


1250 4730 84-150 580-1035 2800 8 6 1 FM Approved


1250 4730 137-191 945-1315 3550 8 6 1 FM Approved


1250 4730 95 655 2300 8 6 1 FM Approved

6THF13

United

States of America

1250 4730 70-123 483-848 2600 8 6 1 FM Approved


1500 5680 78-144 535-990 2800 8 6 1 FM Approved


1500 5680 88-157 605-1080 2950 8 6 1 FM Approved


1500 5680 88 605 2300 8 6 1 FM Approved


1250 4730 84-150 580-1035 2800 8 6 1 FM Approved


1500 5680 88-157 605-1080 2950 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 133-187 915-1290 3550 8 6 1 FM Approved


1500 5680 78-144 535-990 2800 8 6 1 FM Approved

6THF13

United

States of America

1500 5680 64-116 441-800 2600 8 6 1 FM Approved


1500 5680 88 605 2300 8 6 1 FM Approved


1500 5680 133-187 915-1290 3550 8 6 1 FM Approved


1250 4730 93-164 640-1130 2950 8 6 1 FM Approved


1000 3785 74-128 510-883 2600 8 6 1 FM Approved


1250 4730 93-164 640-1130 2950 8 6 1 FM Approved


1250 4730 95 655 2300 8 6 1 FM Approved


1000 3785 97-171 670-1180 2950 8 6 1 FM Approved


1000 3785 152-251 1050-1730 2300 8 6 1 FM Approved


1250 4730 97-166 670-1145 1900 8 6 1 FM Approved


1000 3785 139-228 960-1570 2200 8 6 1 FM Approved


America

1250 4730 122-203 840-1400 2100 8 6 1 FM Approved


1500 5680 108-136 745-940 1760 8 6 1 FM Approved


1500 5680 115-162 795-1115 1900 8 6 1 FM Approved


1500 5680 116-199 800-1370 2100 8 6 1 FM Approved


1500 5680 128-220 885-1515 2200 8 6 1 FM Approved


1000 3785 160-251 1100-1730 2350 8 6 1 FM Approved

6THF19

United

States of America

1250 4730 134-225 925-1550 2200 8 6 1 FM Approved


1000 3785 101-171 695-1180 1900 8 6 1 FM Approved


1250 4730 148-246 1020-1695 2300 8 6 1 FM Approved


1250 4730 155-246 1070-1695 2350 8 6 1 FM Approved


1250 4730 81-142 560-980 1760 8 6 1 FM Approved


1500 5680 143-241 985-1660 2300 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 151-243 1040-1675 2350 8 6 1 FM Approved


1000 3785 85-145 585-1000 1760 8 6 1 FM Approved

6THF19

United

States of America

1000 3785 126-208 870-1435 2100 8 6 1 FM Approved

6TUHF13A2UnitedStates of America

750 2840 242-370 1670-2550 2950 8 6 2 FM Approved


1000 3785 232-362 1600-2495 2950 8 6 2 FM Approved


1250 4730 283-343 1950-2365 2950 8 6 2 FM Approved


1000 3785 209-329 1440-2270 1780 8 6 2 FM Approved


1250 4730 196-327 1350-2255 1780 8 6 2 FM Approved


750 2840 222-338 1530-2330 1780 8 6 2 FM Approved

6TYF13EUnitedStates of America

1250 4730 275-329 1895-2270 2950 8 6 2 FM Approved


750 2840 268-360 1850-2480 2950 8 6 2 FM Approved


1000 3785 254-346 1750-2385 2950 8 6 2 FM Approved


500 1895 277-370 1850-2480 2950 8 6 2 FM Approved

6TYF13FUnitedStates of

America

1250 4730 246-348 1695-2400 2950 8 6 2 FM Approved

6TYF13FUnitedStates of America

1000 3785 268-361 1850-2490 2950 8 6 2 FM Approved


750 2840 276-370 1905-2550 2950 8 6 2 FM Approved


500 1895 283-378 1950-2610 2950 8 6 2 FM Approved


1250 4730 265-331 1830-2280 2300 8 6 2 FM Approved


1250 4730 278-347 1920-2390 2350 8 6 2 FM Approved

6TYF16E

United

States of America

750 2840 166-205 1145-1415 1760 8 6 2 FM Approved


1000 3785 291-361 2010-2490 2350 8 6 2 FM Approved


1000 3785 278-345 1915-2380 2300 8 6 2 FM Approved


1000 3785 227-285 1565-1965 2100 8 6 2 FM Approved


1000 3785 181-230 1250-1585 1900 8 6 2 FM Approved


1000 3785 155-196 1070-1350 1760 8 6 2 FM Approved


7/21/2019 FM guide



750 2840 190-237 1310-1635 1900 8 6 2 FM Approved


750 2840 235-294 1620-2030 2100 8 6 2 FM Approved

6TYF16E

United

States of America

750 2840 284-353 1960-2435 2300 8 6 2 FM Approved


750 2840 296-370 2040-2550 2350 8 6 2 FM Approved


500 1895 288-360 1985-2480 2300 8 6 2 FM Approved


500 1895 300-375 2070-2590 2350 8 6 2 FM Approved


500 1895 171-210 1080-1450 1760 8 6 2 FM Approved


500 1895 195-242 1345-1670 1900 8 6 2 FM Approved


500 1895 240-298 1655-2055 2100 8 6 2 FM Approved


1250 4730 170-215 1170-1480 1900 8 6 2 FM Approved


1250 4730 214-274 1475-1890 2100 8 6 2 FM Approved


2000 7570 63-74 435-510 1760 10 8 1 FM Approved


1500 5680 40-77 275-530 1760 10 8 1 FM Approved


America

2500 9465 52-98 360-675 1760 10 8 1 FM Approved

8AEF15A *UnitedStates of America

2500 9465 105-155 725-1070 2100 10 8 1 FM Approved


3000 11,355 100-151 690-1040 2100 10 8 1 FM Approved


1500 5680 40-63 275-435 1470 10 8 1 FM Approved


2000 7570 69-130 475-895 2100 10 8 1 FM Approved


2000 7570 45-89 310-615 1780 10 8 1 FM Approved

8AEF17 *

United

States of America

2500 9465 65-90 450-620 1460 10 8 1 FM Approved


2500 9465 80-140 550-965 1780 10 8 1 FM Approved


2000 7570 54-94 370-650 1460 10 8 1 FM Approved


2500 9465 66-90 455-620 1460 10 8 1 FM Approved


2500 9465 80-137 550-945 1780 10 8 1 FM Approved


2000 7570 54-94 370-650 1460 10 8 1 FM Approved


7/21/2019 FM guide



2500 9465 55-85 380-585 1470 10 8 1 FM Approved


2500 9465 80-125 550-860 1780 10 8 1 FM Approved

8AEF17N *

United

States of America

2500 9465 115-150 795-1035 2100 10 8 1 FM Approved


2000 7570 55-85 380-585 1470 10 8 1 FM Approved


2500 9465 80-125 550-860 1780 10 8 1 FM Approved


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved

8AEF17V *UnitedStates of America

2000 7570 110-155 760-1070 2100 10 8 1 FM Approved

8AEF17V *UnitedStates of America

2000 7570 90-105 620-725 1780 10 8 1 FM Approved

8AEF17W *UnitedStates of America

2000 7570 110-167 760-1150 2100 10 8 1 FM Approved

8AEF17W *UnitedStates of America

2000 7570 90-118 620-815 1780 10 8 1 FM Approved


1500 5680 73-105 505-710 1470 10 8 1 FM Approved


2000 7570 103-156 710-1015 1780 10 8 1 FM Approved


2000 7570 150-212 1035-1460 2100 10 8 1 FM Approved


America

1500 5680 110-160 760-1105 1780 10 8 1 FM Approved


2500 9465 104-172 715-1185 1780 10 8 1 FM Approved


2500 9465 154-202 1060-1395 2100 10 8 1 FM Approved


2000 7570 72-119 495-820 1470 10 8 1 FM Approved


2000 7570 110-175 760-1205 1780 10 8 1 FM Approved

8AHF26 ††UnitedStates of America

2000 7570 113-185 780-1275 1470 10 8 1 FM Approved

8AHF26 ††

United

States of America

2500 9465 107-179 740-1235 1470 10 8 1 FM Approved

8HFY15UnitedStates of America

3000 11,355 120-150 825-1035 2100-2300 10 8 1 FM Approved


1500 5680 111-166 765-1145 1900-2300 10 8 1 FM Approved


2500 9465 103-155 710-1070 1900-2300 10 8 1 FM Approved


2000 7570 108-160 745-1105 1900-2300 10 8 1 FM Approved

8HFY23AUnitedStates of America

2500 9465 85-161 585-1110 1475 10 8 1 FM Approved


7/21/2019 FM guide


8HFY23AUnitedStates of America

2000 7570 91-164 625-1130 1475 10 8 1 FM Approved

8HFY23BUnitedStates of America

2000 7570 94-150 650-1035 1475 10 8 1 FM Approved

8HFY23B

United

States of America

2500 9465 132-208 910-1435 1750 10 8 1 FM Approved


2000 7570 142-214 980-1475 1750 10 8 1 FM Approved


2500 9465 100-141 690-970 1475 10 8 1 FM Approved


3000 11,355 135-162 930-1115 1475 10 8 1 FM Approved


2500 9465 142-167 980-1150 1475 10 8 1 FM Approved

8HYF23EUnitedStates of America

3000 11,355 179 1234 1490 10 8 1 FM Approved

8HYF23EUnitedStates of America

2500 9465 183 1262 1490 10 8 1 FM Approved

8THF14DUnitedStates of America

1250 4730 96-174 660-1200 2800 10 8 1 FM Approved


2500 9465 102-188 705-1295 2960 10 8 1 FM Approved


2000 7570 97-197 670-1360 2960 10 8 1 FM Approved


2500 9465 95-164 655-1130 2800 10 8 1 FM Approved

8THF14DUnitedStates of

America

2000 7570 104-174 715-1200 2800 10 8 1 FM Approved


1500 5680 110-179 760-1235 2800 10 8 1 FM Approved

8THF14EUnitedStates of America

1250 4730 108-196 745-1350 2950 10 8 1 FM Approved


2000 7570 147-196 1015-1350 3550 10 8 1 FM Approved


2000 7570 95-179 655-1235 2950 10 8 1 FM Approved


1500 5680 105-190 725-1310 2950 10 8 1 FM Approved

8THF14E

United

States of America

2500 9465 119-163 820-1125 2950 10 8 1 FM Approved


2500 9465 105-144 725-995 2800 10 8 1 FM Approved


1500 5680 91-169 630-1165 2800 10 8 1 FM Approved


2000 7570 84-159 580-1095 2800 10 8 1 FM Approved


1500 5680 154-202 1060-1390 3550 10 8 1 FM Approved


1000 3785 124-256 855-1765 2950 10 8 1 FM Approved


7/21/2019 FM guide



1250 4730 120-238 825-1640 2950 10 8 1 FM Approved


1500 5680 118-235 815-1620 2950 10 8 1 FM Approved

8AEF14

United

States of America

2000 7570 107-234 740-1615 2950 10 8 1 FM Approved


2500 9465 98-221 675-1525 2950 10 8 1 FM Approved


Fairbanks Morse A Member of the Pentair Water 800 Airport Rd, North Aurora, Illinois 60542, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

3-1824FUnitedStates of America

250 945 40-100 275-690 3560 4 3 1 FM Approved


250 945 40-121 275-835 2950 4 3 1 FM Approved

3-1824HFUnitedStates of America

250 945 40-100 275-690 3560 4 3 1 FM Approved


250 945 40-121 275-835 2950 4 3 1 FM Approved

2-1/2-1823BFUnitedStates of America

250 945 50-115 345-795 2950 3 2 1/2 1 FM Approved

2-1/2-1823BFUnitedStates of

America

250 945 52-167 360-1150 3560 3 2 1/2 1 FM Approved

2873AFUnitedStates of America

250 945 55-112 380-770 3550 4 2 1 FM Approved


500 1895 40-55 275-380 1770 6 4 1 FM Approved

5823FUnitedStates of America

500 1895 40-80 275-550 1750 5 4 1 FM Approved

4-1823CHFUnitedStates of America

500 1895 55-134 380-925 2950 5 4 1 FM Approved

4"1823DFUnitedStates of America

500 1895 61-134 420-925 2950 5 4 1 FM Approved

4"1823DF

United

States of America

500 1895 63-138 435-950 3000 5 4 1 FM Approved


500 1895 75-170 515-1170 3300 5 4 1 FM Approved


500 1895 76-125 525-860 1750 5 4 1 FM Approved

4-1823AFUnitedStates of America

500 1895 40-55 275-380 1770 5 4 1 FM Approved


500 1895 50-150 345-1030 3560 4 3 1 FM Approved


7/21/2019 FM guide



500 1895 50-150 345-1030 3560 4 3 1 FM Approved

4-1823CFUnitedStates of America

500 1895 55-134 380-925 2950 5 4 1 FM Approved

5-1922F

United

States of America

500 1895 68-144 470-995 1480 6 5 2 FM Approved


500 1895 150-210 1030-1450 1770 5 4 2 FM Approved


500 1895 60-80 415-550 1770 5 4 1 FM Approved


500 1895 75-170 515-1170 3300 5 4 1 FM Approved


500 1895 60-100 415-690 3500 5 4 1 FM Approved


500 1895 100 690 2000 5 4 1 FM Approved


500 1895 100 690 2280 5 4 1 FM Approved


500 1895 125 860 2500 5 4 1 FM Approved


500 1895 178-323 1225-2225 2950 5 5 2 FM Approved


500 1895 185-335 1275-2310 3000 5 5 2 FM Approved


500 1895 100-120 690-825 3500 5 4 1 FM Approved

2874AFUnitedStates of

America

500 1895 55-125 380-860 3300 5 3 1 FM Approved


500 1895 121-125 835-860 3500 5 4 1 FM Approved


500 1895 227-475 1565-3275 3550 5 5 2 FM Approved


500 1895 100-125 690-860 2200 5 4 1 FM Approved


500 1895 126-165 870-1140 3525 4 3 1 FM Approved


500 1895 105-145 725-1000 3275 6 4 1 FM Approved

2874AF

United

States of America

500 1895 66-146 455-1005 3550 5 3 1 FM Approved

2874CFUnitedStates of America

500 1895 91-142 625-980 3550 5 3 1 FM Approved


500 1895 110-170 760-1170 3550 6 4 1 FM Approved


500 1895 49-82 340-565 3000 6 4 1 FM Approved


500 1895 61-100 420-690 3300 6 4 1 FM Approved


500 1895 72-116 495-780 3550 6 4 1 FM Approved


7/21/2019 FM guide



500 1895 97-140 670-965 2600 6 6 1 FM Approved


500 1895 148-164 1020-1130 2800 6 6 1 FM Approved

2876AF

United

States of America

500 1895 157-190 1080-1310 3000 6 6 1 FM Approved


500 1895 163-233 1125-1605 3300 6 6 1 FM Approved


500 1895 191-277 1315-1910 3565 6 6 1 FM Approved


750 2840 40-50 275-345 1770 5 4 1 FM Approved


750 2840 193-248 1330-1710 2600 6 6 2 FM Approved


750 2840 206-344 1420-2370 2950 6 6 2 FM Approved


750 2840 205-357 1415-2460 3000 6 6 2 FM Approved


750 2840 304-506 2095-3490 3550 6 6 2 FM Approved


750 2840 65-205 450-1415 3560 5 4 1 FM Approved


750 2840 65-205 450-1415 3560 5 4 1 FM Approved


750 2840 66-165 455-1140 3300 5 4 1 FM Approved

4-1823CFUnitedStates of

America

750 2840 66-165 455-1140 3300 5 4 1 FM Approved


750 2840 71-97 490-670 1770 5 4 1 FM Approved


750 2840 50-70 345-485 1770 6 5 1 FM Approved

4"1823DFUnitedStates of America

750 2840 81-190 560-1310 3550 5 4 1 FM Approved


750 2840 105-154 725-1060 2950 6 5 1 FM Approved


750 2840 105-154 725-1060 2950 6 5 1 FM Approved

6-1922AF

United

States of America

750 2840 80-175 550-1205 1480 8 6 2 FM Approved


750 2840 80-175 550-1205 1480 8 6 2 FM Approved


750 2840 138-246 950-1695 1770 8 6 2 FM Approved


750 2840 138-246 950-1695 1770 8 6 2 FM Approved


750 2840 132-148 910-1020 2800 6 6 1 FM Approved


750 2840 142-175 980-1205 3000 6 6 1 FM Approved


7/21/2019 FM guide



750 2840 147-218 1015-1505 3300 6 6 1 FM Approved


750 2840 179-265 1235-1825 3565 6 6 1 FM Approved

2822XF

United

States of America

750 2840 40-56 275-385 1770 6 6 1 FM Approved


750 2840 67-78 460-540 3000 6 4 1 FM Approved


750 2840 73-96 505-660 3300 6 4 1 FM Approved


750 2840 63-113 435-780 3550 6 4 1 FM Approved


750 2840 40-62 275-430 1770 8 5 1 FM Approved


750 2840 40-80 275-550 1750 6 5 1 FM Approved


750 2840 51-87 350-560 1770 6 4 1 FM Approved


750 2840 54-90 370-620 1770 6 4 1 FM Approved


750 2840 55-126 380-870 2100 6 4 1 FM Approved


750 2840 57-152 395-1050 2300 6 4 1 FM Approved


750 2840 59-131 405-905 2100 6 4 1 FM Approved

5824FUnitedStates of

America

750 2840 71-125 490-860 1750 5 4 1 FM Approved


750 2840 73-160 505-1105 2300 6 4 1 FM Approved


750 2840 89-143 615-985 1770 8 5 1 FM Approved


750 2840 94-203 650-1400 2100 8 5 1 FM Approved


750 2840 96-154 660-1060 3000 6 4 1 FM Approved


750 2840 95-198 655-1365 3300 6 4 1 FM Approved

2876AF

United

States of America

750 2840 95-230 655-1585 3550 6 4 1 FM Approved


750 2840 125-180 860-1240 1750 6 5 2 FM Approved


750 2840 100-125 690-860 3500 6 5 1 FM Approved


750 2840 100-125 690-860 2500 5 4 1 FM Approved


750 2840 105-150 725-1035 3275 8 5 1 FM Approved


750 2840 105-180 725-1240 3550 8 5 1 FM Approved


7/21/2019 FM guide


7/21/2019 FM guide


6-1822HHFUnitedStates of America

1000 3785 88-219 607-1441 3560 8 6 1 FM Approved


1000 3785 90-128 620-885 1770 6 5 1 FM Approved

5-1822CHF

United

States of America

1000 3785 90-160 620-1105 3550 6 5 1 FM Approved


1000 3785 90-160 620-1105 3550 6 5 1 FM Approved


1000 3785 91-153 625-1055 2300 6 4 1 FM Approved


1000 3785 92-151 635-1040 2300 8 5 1 FM Approved


1000 3785 93-150 641-1034 2950 8 6 1 FM Approved


1000 3785 95-123 655-850 2100 6 4 1 FM Approved


1000 3785 95-145 655-1000 3275 8 5 1 FM Approved


1000 3785 95-170 655-1170 3550 8 5 1 FM Approved


1000 3785 96-160 662-1103 2300 8 6 1 FM Approved


1000 3785 97-146 670-1005 2950 6 5 1 FM Approved


1000 3785 97-146 670-1005 2950 6 5 1 FM Approved

6-1822HHFUnitedStates of

America

1000 3785 99-155 683-1069 3000 8 6 1 FM Approved

5-1822BHFUnitedStates of America

1000 3785 101-165 695-1140 3300 6 5 1 FM Approved

5-1822BFUnitedStates of America

1000 3785 101-165 695-1140 3300 6 5 1 FM Approved


1000 3785 102-278 703-1917 2950 8 6 1 FM Approved


1000 3785 105-145 725-1000 3300 10 6 1 FM Approved


1000 3785 105-182 725-1255 3570 10 6 1 FM Approved

6-1823HHF

United

States of America

1000 3785 105-287 724-1979 3000 8 6 1 FM Approved


1000 3785 109-242 750-1670 2300 8 5 1 FM Approved


1000 3785 120-200 830-1380 3550 6 5 1 FM Approved


1000 3785 120-200 830-1380 3550 6 5 1 FM Approved


1000 3785 130-243 895-1675 1770 8 6 2 FM Approved


1000 3785 130-243 895-1675 1770 8 6 2 FM Approved


7/21/2019 FM guide



1000 3785 130-248 896-1710 3300 8 6 1 FM Approved


1000 3785 154-287 1062-1979 3560 8 6 1 FM Approved

8-1822F

United

States of America

1250 4730 43-53 295-365 1770 10 8 1 FM Approved


1250 4730 55-95 380-655 1770 8 6 1 FM Approved


1250 4730 55-95 380-655 1770 8 6 1 FM Approved


1250 4730 55-96 380-660 1770 8 6 1 FM Approved


1250 4730 64-84 440-580 1780 8 5 1 FM Approved


1250 4730 78-106 540-730 1480 8 6 1 FM Approved


1250 4730 78-106 540-730 1480 8 6 1 FM Approved


1250 4732 87-156 600-1076 2300 8 6 1 FM Approved


1250 4730 87-168 600-1160 1770 8 6 1 FM Approved


1250 4730 87-168 600-1160 1770 8 6 1 FM Approved


1250 4730 90-144 620-995 1480 10 8 1 FM Approved

2823AFUnitedStates of

America

1250 4730 94-121 650-835 2100 8 5 1 FM Approved


1250 4732 94-130 648-896 2100 8 6 1 FM Approved


1250 4732 96-110 662-758 2600 8 6 1 FM Approved


1250 4732 98-145 676-1000 2950 8 6 1 FM Approved


1250 4730 100-138 690-950 1770 8 6 1 FM Approved


1250 4730 100-138 690-950 1770 8 6 1 FM Approved

6-1822HHF

United

States of America

1250 4732 102-151 703-1041 3000 8 6 1 FM Approved


1250 4732 110-278 758-1917 2950 8 6 1 FM Approved


1250 4732 111-182 765-1255 3300 8 6 1 FM Approved


1250 4732 113-287 779-1979 3000 8 6 1 FM Approved


1250 4730 116-147 800-1015 2300 8 5 1 FM Approved


1250 4732 122-201 841-1386 2600 8 6 1 FM Approved


7/21/2019 FM guide


7/21/2019 FM guide



1500 5680 95-135 655-930 2100 10 6 1 FM Approved


1500 5680 96-164 660-1130 2300 10 6 1 FM Approved

5876F

United

States of America

1500 5680 100-175 690-1205 3570 10 6 1 FM Approved


1500 5678 121-137 834-945 2950 8 6 1 FM Approved


1500 5678 126-144 869-993 3000 8 6 1 FM Approved


1500 5678 133-240 917-1655 3300 8 6 1 FM Approved


1500 5680 135-200 930-1380 1775 10 8 1 FM Approved


1500 5678 142-196 979-1351 2600 8 6 1 FM Approved


1500 5678 142-209 979-1441 3560 8 6 1 FM Approved


1500 5678 153-275 1055-1896 2950 8 6 1 FM Approved


1500 5678 158-283 1089-1951 3560 8 6 1 FM Approved


1500 5678 159-285 1096-1965 3000 8 6 1 FM Approved


2000 7570 52-94 350-650 1480 10 8 1 FM Approved

8-1825FUnitedStates of

America

2000 7570 82-137 565-945 1480 10 8 1 FM Approved


2000 7570 70-125 485-860 1770 10 8 1 FM Approved


2000 7570 120-152 830-1050 1770 8 6 1 FM Approved


2000 7570 120-152 830-1050 1770 8 6 1 FM Approved


2000 7570 51-130 350-895 1770 10 8 1 FM Approved


2000 7570 80-100 550-690 1770 8 6 1 FM Approved

6-1824CHF

United

States of America

2000 7570 120-152 830-1050 1770 8 6 1 FM Approved


2000 7570 100-140 690-965 1770 8 6 1 FM Approved


2000 7570 100-140 690-965 1770 8 6 1 FM Approved


2000 7570 100-125 690-860 2100 8 6 1 FM Approved


2000 7570 128-196 880-1350 1775 10 8 1 FM Approved


2000 7570 63-88 435-605 1750 10 8 1 FM Approved


7/21/2019 FM guide



2000 7570 87-134 560-925 1770 10 6 1 FM Approved


2000 7570 100-125 690-860 1750 10 8 1 FM Approved

2824CF

United

States of America

2000 7570 105-173 725-1195 2100 10 6 1 FM Approved


2000 7570 110-157 760-1085 1770 10 6 1 FM Approved


2000 7570 89-131 615-905 2100 10 6 1 FM Approved


2000 7570 88-160 605-1105 2300 10 6 1 FM Approved


2000 7570 106-176 730-1215 1480 12 8 1 FM Approved


2000 7570 126-150 870-1035 1750 10 8 1 FM Approved


2000 7570 132-200 910-1380 2100 10 6 1 FM Approved


2500 9465 65-101 450-695 1480 12 10 1 FM Approved


2500 9465 75-130 515-895 1770 10 8 1 FM Approved


2500 9465 115-145 795-1000 2100 10 8 1 FM Approved


2500 9465 123-193 850-1330 1770 10 8 1 FM Approved

5823FUnitedStates of

America

2500 9465 62-98 430-675 1750 12 10 1 FM Approved


2500 9465 50-84 345-580 1770 12 8 1 FM Approved

10-1824DFUnitedStates of America

2500 7570 63-96 435-660 1480 12 10 1 FM Approved


2500 9465 72-119 495-820 2100 12 8 1 FM Approved


2500 9465 88-144 605-995 2300 12 8 1 FM Approved


2500 9465 100-125 690-860 1750 10 8 1 FM Approved

8-5826F

United

States of America

2500 9465 100-172 690-1185 1480 12 8 1 FM Approved


2500 9465 112-141 770-970 1785 12 8 1 FM Approved


2500 9465 136-171 940-1180 2100 12 8 1 FM Approved


2500 9465 155-213 1070-1470 1785 12 8 1 FM Approved


3000 11,355 61-100 420-690 1480 12 10 1 FM Approved


3000 11,355 61-95 420-655 1480 12 10 1 FM Approved


7/21/2019 FM guide



3000 11,355 90-138 620-950 1770 12 10 1 FM Approved


3000 11,355 100-110 690-760 2300 12 10 1 FM Approved

10-1824F

United

States of America

3000 11,355 99-140 685-965 1775 12 10 1 FM Approved


3000 11,355 91-116 625-780 2100 12 8 1 FM Approved


3000 11,355 80 550 1770 12 8 1 FM Approved

5824F *UnitedStates of America

3000 11,355 100-153 690-1055 1770 12 10 1 FM Approved


3000 11,355 103-134 710-925 1770 12 8 1 FM Approved


3000 11,355 130-165 895-1140 2100 12 8 1 FM Approved


3500 13,250 59-94 405-650 1480 12 10 1 FM Approved


3500 13,250 59-97 405-670 1480 12 10 1 FM Approved


3500 13,250 88-135 605-930 1770 12 10 1 FM Approved

5824F *UnitedStates of America

3500 13,250 94-151 650-1040 1770 12 10 1 FM Approved


3500 13,250 98-140 675-965 1775 12 10 1 FM Approved

10-2825AFUnitedStates of

America

4000 15,140 61-134 420-924 1480 16 10 1 FM Approved


4000 15,140 62-92 425-635 1480 12 10 1 FM Approved


4000 15,140 67-103 460-715 1480 14 12 1 FM Approved


4000 15,140 85-134 585-925 1770 12 10 1 FM Approved


4000 15,140 94-198 648-1365 1785 16 10 1 FM Approved


4000 15,140 95-110 655-760 1775 12 10 1 FM Approved

10-2825AF

United

States of America

4000 15,140 110-225 758-1551 1900 16 10 1 FM Approved


4500 17,035 71-133 489-917 1480 16 10 1 FM Approved


4500 17,035 81-132 560-910 1770 12 10 1 FM Approved


4500 17,035 90-195 620-1344 1785 16 10 1 FM Approved


4500 17,035 106-223 731-1538 1900 16 10 1 FM Approved


4500 17,035 175 1205 1185 14 10 1 FM Approved


7/21/2019 FM guide



5000 18,925 82-132 565-910 1480 16 10 1 FM Approved


5000 18,925 88-195 607-1344 1785 16 10 1 FM Approved

10-1824DF

United

States of America

5000 18,925 90-130 620-895 1770 12 10 1 FM Approved


5000 18,925 102-221 703-1524 1900 16 10 1 FM Approved


2500 9465 114-167 785-1150 1475 12 8 1 FM Approved


2500 9465 215 1480 1775 12 8 1 FM Approved


2000 7570 110-173 760-1195 1475 12 8 1 FM Approved


2000 7570 167-220 1150-1515 1775 12 8 1 FM Approved


500 1895 163-215 1125-1480 1760 8 6 2 FM Approved


500 1895 166-220 1145-1515 1780 8 6 2 FM Approved


500 1895 243-385 1675-2655 2950 8 6 2 FM Approved


750 2840 154-206 1060-1420 1760 8 6 2 FM Approved


750 2840 158-211 1090-1455 1780 8 6 2 FM Approved


America

750 2840 183-242 1260-1670 1900 8 6 2 FM Approved


750 2840 206-353 1420-2435 2350 8 6 2 FM Approved


750 2840 215-340 1480-2345 2800 8 6 2 FM Approved


750 2840 229-300 1580-2070 2100 8 6 2 FM Approved


750 2840 237-376 1635-2590 2950 8 6 2 FM Approved


750 2840 260-413 1795-2850 2600 8 6 2 FM Approved

6-1923F

United

States of America

1000 3785 145-197 1000-1360 1760 8 6 2 FM Approved


1000 3785 149-202 1025-1395 1780 8 6 2 FM Approved


1000 3785 172-231 1185-1595 1900 8 6 2 FM Approved


1000 3785 195-340 1345-2345 2350 8 6 2 FM Approved


1000 3785 205-329 1415-2270 2800 8 6 2 FM Approved


1000 3785 218-290 1505-2000 2100 8 6 2 FM Approved


7/21/2019 FM guide



1000 3785 228-365 1570-2515 2950 8 6 2 FM Approved


1000 3785 251-403 1715-2780 2600 8 6 2 FM Approved

6-1923F

United

States of America

1250 4732 136-185 940-1275 1760 8 6 2 FM Approved


1250 4732 139-189 960-1305 1780 8 6 2 FM Approved


1250 4732 161-219 1110-1510 1900 8 6 2 FM Approved


1250 4732 183-327 1260-2255 2350 8 6 2 FM Approved


1250 4732 193-317 1330-2185 2800 8 6 2 FM Approved


1250 4732 206-277 1420-1910 2100 8 6 2 FM Approved


1250 4732 216-349 1490-2405 2950 8 6 2 FM Approved


1250 4732 239-390 1650-2690 2600 8 6 2 FM Approved


1500 5680 170-313 1170-2160 2350 8 6 2 FM Approved


1500 5680 192-262 1325-1805 2100 8 6 2 FM Approved


1500 5680 225-374 1550-2580 2600 8 6 2 FM Approved


America

1500 5680 302 2080 2800 8 6 2 FM Approved


1500 5680 336 2315 2950 8 6 2 FM Approved

* Max discharge pressure is 200 psi (1380 kPa).

Rapidrop Global LimitedRutland Business Park, Newark Rd, Peterborough PE15WA, United Kingdom





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

RDSC100/48

UnitedKingdom

400 1515 120-126 703-869 1760 5 4 1 FM Approved

RDSC

100/48

United

Kingdom

450 1705 102-126 703-869 1760 5 4 1 FM Approved

RDSC125/38

UnitedKingdom

500 1895 45-67 310-462 1450 6 5 1 FM Approved

RDSC100/48

UnitedKingdom

500 1895 100-126 689-869 1760 5 4 1 FM Approved

RDSC125/38

UnitedKingdom

750 2840 70-100 483-689 1760 6 5 1 FM Approved

RDSC125/48

UnitedKingdom

750 2840 88-118 607-814 1450 8 5 1 FM Approved

RDSC150/48

UnitedKingdom

750 2840 88-115 607-793 1450 8 6 1 FM Approved

RDSC125/48

UnitedKingdom

750 2840 130-178 896-1227 1760 8 5 1 FM Approved

RDSC150/56

UnitedKingdom

1000 3780 77-88 531-607 1100 8 6 1 FM Approved


7/21/2019 FM guide


RDSC125/48

UnitedKingdom

1000 3780 85-116 586-800 1450 8 5 1 FM Approved

RDSC150/48

UnitedKingdom

1000 3780 86-114 593-786 1450 8 6 1 FM Approved

RDSC150/48

UnitedKingdom

1000 3780 127-168 876-1158 1760 8 6 1 FM Approved

RDSC

125/48

United


RDSC150/56

UnitedKingdom

1000 3780 142-155 979-1068 1450 8 6 1 FM Approved

RDSC150/56

UnitedKingdom

1250 4730 75-86 517-593 1100 8 6 1 FM Approved

RDSC150/48

UnitedKingdom

1250 4730 85-112 586-772 1450 8 6 1 FM Approved

RDSC200/48

UnitedKingdom

1250 4730 96-117 662-807 1450 10 8 1 FM Approved

RDSC150/48

UnitedKingdom

1250 4730 124-166 855-1144 1760 8 6 1 FM Approved

RDSC125/48

UnitedKingdom

1250 4730 125-174 862-1200 1760 8 5 1 FM Approved

RDSC125/48

UnitedKingdom

1250 4730 125-174 862-1200 1760 8 5 1 FM Approved

RDSC

200/54

United


RDSC150/56

UnitedKingdom

1500 5680 72-83 496-572 1100 8 6 1 FM Approved

RDSC200/48

UnitedKingdom

1500 5680 94-117 648-807 1450 10 8 1 FM Approved

RDSC150/48

UnitedKingdom

1500 5680 121-162 834-1117 1760 8 6 1 FM Approved

RDSC150/56

UnitedKingdom

1500 5680 138-151 951-1041 1450 8 6 1 FM Approved

RDSC200/48

UnitedKingdom

1500 5680 142-172 979-1186 1760 10 8 1 FM Approved

RDSC200/54

UnitedKingdom

2000 7570 65-77 448-531 1100 12 8 1 FM Approved

RDSC200/48

UnitedKingdom

2000 7570 90-115 621-793 1450 10 8 1 FM Approved

RDSC

200/54

United


RDSC200/48

UnitedKingdom

2000 7570 139-172 958-1186 1760 10 8 1 FM Approved

RDSC250/50

UnitedKingdom

2500 9465 61-65 421-448 1100 14 10 1 FM Approved

RDSC250/54

UnitedKingdom

2500 9465 120-136 827-938 1450 12 8 1 FM Approved

RDSC200/48

UnitedKingdom

2500 9465 133-168 917-1158 1760 10 8 1 FM Approved

RDSC250/50

UnitedKingdom

3000 11,355 61-65 421-448 1100 14 10 1 FM Approved

RDSC250/50

UnitedKingdom

3000 11,355 106-112 731-772 1450 14 10 1 FM Approved

RDSC250/50

UnitedKingdom

3500 13,250 60-64 414-441 1100 14 10 1 FM Approved

RDSC

250/50

United

Kingdom3500 13,250 106-112 731-772 1450 14 10 1 FM Approved

RDSC250/50

UnitedKingdom

4000 15,140 106-111 731-765 1450 14 10 1 FM Approved

Reddy-Buffaloes Pump Inc1 Dixie Dr, Box 557, Baxley, Georgia 31513, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

10x10DF


1500 5680 46-130 315-895 1795 10 10 1 FM Approved


7/21/2019 FM guide


10x10DF


1500 5680 60-158 415-1090 1785 10 10 1 FM Approved

10x10DF


1500 5680 85-220 585-1515 2100 10 10 1 FM Approved

10x10DF

United

States of America

1500 5680 100-140 690-965 2300 10 10 1 FM Approved

10x10DF


1500 5680 150-205 1035-1415 3300 10 10 1 FM Approved

10x10DF


1500 5680 180-245 1240-1690 3580 10 10 1 FM Approved

10x10DF


1500 5680 73-109 505-750 1495 10 10 1 FM Approved

10x10DF


2000 7570 42-125 290-860 1795 10 10 1 FM Approved

10x10DF


2000 7570 55-154 380-1060 1785 10 10 1 FM Approved

10x10DF


2000 7570 80-215 550-1480 2100 10 10 1 FM Approved

10x10DF


2000 7570 100-200 690-1380 2300 10 10 1 FM Approved

10x10DF


2000 7570 150-205 1035-1415 3300 10 10 1 FM Approved

10x10DF


2000 7570 145-230 1000-1585 2950 10 10 1 FM Approved

10x10DF


2000 7570 180-240 1240-1655 3580 10 10 1 FM Approved

10x10DF

UnitedStates of

America

2000 7570 69-104 475-715 1495 10 10 1 FM Approved

10x10DF


2500 9465 55-150 380-1035 1785 10 10 1 FM Approved

10x10DF


2500 9465 64-98 440-675 1495 10 10 1 FM Approved

10x10DF


2500 9465 80-208 550-1435 2100 10 10 1 FM Approved

10x10DF


2500 9465 100-195 690-1345 2300 10 10 1 FM Approved

10x10DF


2500 9565 136-216 940-1490 2950 10 10 1 FM Approved

10x10DF

United

States of America

2500 9465 150-200 1035-1380 3300 10 10 1 FM Approved

10x10DF


2500 9465 180-240 1240-1655 3580 10 10 1 FM Approved

10x10DF


3000 11,355 65-142 450-980 1785 10 10 1 FM Approved

10x10DF


3000 11,355 91 625 1495 10 10 1 FM Approved

10x10DF


3000 11,355 95-186 655-1280 2300 10 10 1 FM Approved

10x10DF


3000 11,355 75-200 515-1380 2100 10 10 1 FM Approved


7/21/2019 FM guide


10x10DF


3000 11,355 235 1620 3580 10 10 1 FM Approved

10x10DF


3500 13,250 97-112 670-770 1785 10 10 1 FM Approved

10x10DF

United

States of America

3500 13,250 90-160 620-1105 2100 10 10 1 FM Approved

10x10DF


3500 13,250 177 1220 2300 10 10 1 FM Approved

10x10DF


1000 3785 62-160 425-1105 1785 10 10 1 FM Approved

10x10DF


1250 4730 62-160 425-1105 1785 10 10 1 FM Approved

10x10LDF


1500 5680 119-225 820-1550 1600 10 10 1 FM Approved

10x10LDF


1500 5680 151-286 1040-1970 1800 10 10 1 FM Approved

10x10LDF


1500 5680 205-281 1415-1935 2100 10 10 1 FM Approved

10x10LDF


2000 7570 116-195 800-1344 1480 10 10 1 FM Approved

10x10LDF


2500 9465 95-190 655-1310 1500 10 10 1 FM Approved

10x10LDF


2500 9465 110-212 760-1460 1600 10 10 1 FM Approved

10x10LDF


2500 9465 143-272 985-1875 1800 10 10 1 FM Approved

10x10LDF

UnitedStates of

America

2500 9465 200-273 1380-1880 2100 10 10 1 FM Approved

10x10LDF


3000 11,355 103-173 710-1193 1480 10 10 1 FM Approved

10x10LDF


3000 11,355 161-216 1110-1489 1780 10 10 1 FM Approved

10x10LDF


2000 7570 173-238 1195-1641 1780 10 10 1 FM Approved

10x10LDF


2000 7570 100-200 690-1380 1500 10 10 1 FM Approved

10x10LDF


2000 7570 115-220 795-1515 1600 10 10 1 FM Approved

10x10LDF

United

States of America

2000 7570 147-281 1015-1935 1800 10 10 1 FM Approved

10x10LDF


3000 11,355 89-178 615-1225 1500 10 10 1 FM Approved

10x10LDF


3000 11,355 104-206 715-1420 1600 10 10 1 FM Approved

10x10LDF


3000 11,355 193-268 1330-1850 2100 10 10 1 FM Approved

10x10LDF


3000 11,355 264 1820 1800 10 10 1 FM Approved

10x10LDF


3500 13,250 96-153 660-1055 1480 10 10 1 FM Approved


7/21/2019 FM guide


10x10LDF


3500 13,250 152-206 1050-1420 1780 10 10 1 FM Approved

10x10LDF


2000 7570 201-277 1385-1910 2100 10 10 1 FM Approved

10x10LDF

United

States of America

2500 9565 110-186 760-1282 1480 10 10 1 FM Approved

10x10LDF


2500 9565 168-229 1160-1579 1780 10 10 1 FM Approved

10x10LDF


1500 5680 177-247 1220-1703 1780 10 10 1 FM Approved

10x10LDF


3500 13,250 162 1115 1500 10 10 1 FM Approved

10x10LDF


3500 13,250 195 1345 1600 10 10 1 FM Approved

10x10LDF


3500 13,250 251 1730 1800 10 10 1 FM Approved

10x10LDF


1500 5680 121-203 835-1400 1480 10 10 1 FM Approved

10x10LDF


1500 5680 104-208 715-1435 1500 10 10 1 FM Approved

10x10LDF


1000 3785 151-295 1040-2035 1800 10 10 1 FM Approved

10x10LDF


1250 4730 151-290 1040-2000 1800 10 10 1 FM Approved

12x12DF


3000 11,355 114-170 785-1170 1780 12 12 1 FM Approved

12x12DF

UnitedStates of

America

3000 11,355 78-114 535-785 1480 12 12 1 FM Approved

12x12DF


4000 15,140 70-108 485-745 1480 12 12 1 FM Approved

12x12DF


4000 15,140 108-158 745-1090 1780 12 12 1 FM Approved

12x12DF


4500 17,035 67-104 460-715 1480 12 12 1 FM Approved

12x12DF


4500 17,035 105-155 725-1070 1780 12 12 1 FM Approved

12x12DF


5000 18,925 65-100 450-690 1480 12 12 1 FM Approved

12x12DF

United

States of America

5000 18,925 117-150 805-1035 1780 12 12 1 FM Approved

12x12DF


2000 7570 122-182 840-1255 1780 12 12 1 FM Approved

12x12DF


3500 13,250 112-162 770-1115 1780 12 12 1 FM Approved

12x12DF


3500 13,250 75-110 515-760 1480 12 12 1 FM Approved

12x12DF


2500 9465 119-177 820-1220 1780 12 12 1 FM Approved

14x12DF


2500 9465 116-190 800-1310 1450 14 12 1 FM Approved


7/21/2019 FM guide


14x12DF


3500 13,250 112-180 770-1240 1450 14 12 1 FM Approved

14x12DF


4500 17,035 104-165 715-1140 1450 14 12 1 FM Approved

14x12DF

United

States of America

3000 11,355 114-186 785-1280 1450 14 12 1 FM Approved

14x12DF


4000 15,140 108-173 745-1120 1450 14 12 1 FM Approved

14x12DF


5000 18,925 97-158 670-1090 1450 14 12 1 FM Approved

3x3 DFUnitedStates of America

400 1515 56-186 385-1280 3525 3 3 1 FM Approved


500 1895 120 830 3000 3 3 1 FM Approved


500 1895 93-175 640-1205 3525 3 3 1 FM Approved


200 755 43-80 295-550 2300 3 3 1 FM Approved


200 755 45-140 310-965 3000 3 3 1 FM Approved


200 755 62-198 425-1365 3525 3 3 1 FM Approved


250 945 42-78 290-540 2300 3 3 1 FM Approved


250 945 44-139 305-960 3000 3 3 1 FM Approved

3x3 DFUnitedStates of

America

250 945 61-195 420-1345 3525 3 3 1 FM Approved


300 1135 40-75 275-515 2300 3 3 1 FM Approved


300 1135 43-136 295-940 3000 3 3 1 FM Approved


300 1135 60-195 415-1345 3525 3 3 1 FM Approved


400 1515 69 475 2300 3 3 1 FM Approved


400 1515 43-127 295-875 3000 3 3 1 FM Approved

3x3 LDF

United

States of America

300 1135 61-98 420-675 1800 3 3 1 FM Approved

3x3 LDFUnitedStates of America

500 1895 232-400 1600-2760 3560 3 3 1 FM Approved


750 2840 70-107 480-740 2100 3 3 1 FM Approved


750 2840 88-136 605-940 2300 3 3 1 FM Approved


750 2840 160-260 1105-1795 3000 3 3 1 FM Approved


750 2840 227-375 1565-2585 3560 3 3 1 FM Approved


7/21/2019 FM guide



300 1135 84-136 580-940 2100 3 3 1 FM Approved


300 1135 100-162 690-1115 2300 3 3 1 FM Approved

3x3 LDF

United

States of America

250 945 43-70 295-480 1500 3 3 1 FM Approved


300 1135 170-288 1170-1985 3000 3 3 1 FM Approved


250 945 101-165 695-1140 2300 3 3 1 FM Approved


250 945 170-290 1170-2000 3000 3 3 1 FM Approved


300 1135 238-405 1640-2790 3560 3 3 1 FM Approved


400 1515 41-64 280-440 1500 3 3 1 FM Approved


400 1515 60-95 415-655 1800 3 3 1 FM Approved


400 1515 60-95 415-655 1800 3 3 1 FM Approved


400 1515 82-132 565-910 2100 3 3 1 FM Approved


400 1515 98-158 675-1090 2300 3 3 1 FM Approved


250 945 62-100 430-690 1800 3 3 1 FM Approved

3x3 LDFUnitedStates of

America

400 1515 168-285 1160-1965 3000 3 3 1 FM Approved


400 1515 235-402 1620-2770 3560 3 3 1 FM Approved


250 945 85-138 585-950 2100 3 3 1 FM Approved


250 945 238-407 1640-2805 3560 3 3 1 FM Approved


500 1895 40-58 275-400 1500 3 3 1 FM Approved


500 1895 58-91 400-630 1800 3 3 1 FM Approved

3x3 LDF

United

States of America

500 1895 80-128 550-880 2100 3 3 1 FM Approved


500 1895 96-153 660-1055 2300 3 3 1 FM Approved


500 1895 166-278 1145-1915 3000 3 3 1 FM Approved


300 1135 43-68 295-470 1500 3 3 1 FM Approved

3x3DFUnitedStates of America

500 1895 90 621 2600 3 3 1 FM Approved


250 945 59-108 407-745 2600 3 3 1 FM Approved


7/21/2019 FM guide



450 1705 49-95 338-655 2600 3 3 1 FM Approved


200 755 60-110 414-758 2600 3 3 1 FM Approved

3x3DF

United

States of America

300 1135 58-107 400-738 2600 3 3 1 FM Approved


400 1575 53-102 365-703 2600 3 3 1 FM Approved


500 1895 60 414 2600 3 3 1 FM Approved


400 1515 54-197 370-1360 3530 5 4 1 FM Approved


450 1705 40-130 275-895 2980 5 4 1 FM Approved


500 1895 51-188 350-1295 3530 5 4 1 FM Approved


250 945 41-140 285-965 2980 5 4 1 FM Approved


450 1705 52-193 360-1330 3530 5 4 1 FM Approved


500 1895 47-126 325-870 2980 5 4 1 FM Approved


750 2840 43-105 296-724 3000 5 4 1 FM Approved


400 1515 40-133 275-915 2980 5 4 1 FM Approved


America

750 2840 70-154 483-1062 3580 5 4 1 FM Approved


300 1135 40-135 275-930 2980 5 4 1 FM Approved


400 1575 59-106 407-731 2600 5 4 1 FM Approved


300 1135 60-108 414-745 2600 5 4 1 FM Approved


750 2840 49-95 338-655 2600 5 4 1 FM Approved


250 945 60-110 414-758 2600 5 4 1 FM Approved

5x4DF

United

States of America

500 1895 56-104 368-717 2600 5 4 1 FM Approved


450 1705 47-86 325-595 1500 5 5 1 FM Approved


500 1895 45-85 310-585 1500 5 5 1 FM Approved


400 1515 48-88 330-605 1500 5 5 1 FM Approved


500 1895 85-180 585-1240 2100 5 5 1 FM Approved


500 1895 71-128 490-880 1800 5 5 1 FM Approved


7/21/2019 FM guide



500 1895 101-215 695-1480 2300 5 5 1 FM Approved


500 1895 177-255 1220-1760 3000 5 5 1 FM Approved

5x5 LDF

United

States of America

750 2840 74-165 510-1140 2100 5 5 1 FM Approved


750 2840 92-200 635-1380 2300 5 5 1 FM Approved


750 2840 67-115 460-880 1800 5 5 1 FM Approved


750 2840 167-240 1150-1655 3000 5 5 1 FM Approved


750 2840 245-273 1690-1880 3565 5 5 1 FM Approved


1000 3785 151-220 1040-1515 3000 5 5 1 FM Approved


1000 3785 106-178 730-1230 2300 5 5 1 FM Approved


1000 3785 229-255 1580-1760 3565 5 5 1 FM Approved


500 1895 253-285 1745-1965 3565 5 5 1 FM Approved

6x5 TFUnitedStates of America

1000 3785 155-204 1070-1405 2100 6 5 2 FM Approved


1000 3785 280-494 1930-3406 2950 6 5 2 FM Approved

6x5 TFUnitedStates of

America

1000 3785 290-511 2000-3523 3000 6 5 2 FM Approved


1000 3785 305 2105 3580 6 5 2 FM Approved


500 1895 325 2240 2300 6 5 2 FM Approved


500 1875 305-537 2105-3702 2950 6 5 2 FM Approved


750 2840 175 1205 1780 6 5 2 FM Approved


750 2840 110-255 760-1760 2100 6 5 2 FM Approved

6x5 TF

United

States of America

750 2840 175-545 1205-3760 3580 6 5 2 FM Approved


500 1875 315-554 2170-3820 3000 6 5 2 FM Approved


750 2840 310 2140 2300 6 5 2 FM Approved


750 2840 295-520 2035-3585 2950 6 5 2 FM Approved


750 2840 310-538 2140-3709 3000 6 5 2 FM Approved


500 1895 93-195 640-1345 1780 6 5 2 FM Approved


7/21/2019 FM guide



500 1895 128-275 885-1895 2100 6 5 2 FM Approved


1000 3785 199-290 1370-2000 2300 6 5 2 FM Approved

6x5 TF

United

States of America

500 1895 200-563 1380-3880 3580 6 5 2 FM Approved


500 1895 57-185 395-1275 3540 6 6 1 FM Approved


750 2840 40-154 275-1060 3000 6 6 1 FM Approved


500 1895 58-217 400-1495 3570 6 6 1 FM Approved


750 2840 49-165 340-1140 3300 6 6 1 FM Approved


750 2840 57-180 395-1240 3540 6 6 1 FM Approved


500 1895 40-56 275-385 1760 6 6 1 FM Approved


750 2840 58-116 400-800 2800 6 6 1 FM Approved


1250 4730 105-188 725-1295 3565 6 6 1 FM Approved


1250 4730 137 945 3000 6 6 1 FM Approved


750 2840 58-210 400-1450 3570 6 6 1 FM Approved


America

750 2840 40-53 275-365 1760 6 6 1 FM Approved


500 1895 40-160 275-1105 3000 6 6 1 FM Approved


1000 3785 46-147 315-1015 3000 6 6 1 FM Approved


1000 3785 52-105 360-725 2800 6 6 1 FM Approved


1000 3785 75-155 515-1070 3300 6 6 1 FM Approved


1000 3785 60-169 415-1165 3540 6 6 1 FM Approved

6x6 DF

United

States of America

1000 3785 62-200 430-1380 3570 6 6 1 FM Approved


500 1895 49-173 340-1195 3300 6 6 1 FM Approved


500 1895 270 1860 2880 6 6 1 FM Approved


1500 5675 57-127 395-875 1780 6 6 1 FM Approved


1500 5675 84-183 580-1260 2100 6 6 1 FM Approved


1500 5675 100-208 690-1435 2300 6 6 1 FM Approved


7/21/2019 FM guide



750 2840 52-67 360-460 1500 6 6 1 FM Approved


750 2840 46-95 315-655 1500 6 6 1 FM Approved

6x6 LDF

United

States of America

500 1895 164-222 1130-1530 3000 6 6 1 FM Approved


750 2840 69-141 475-972 1780 6 6 1 FM Approved


1000 3785 45-93 310-640 1500 6 6 1 FM Approved


1500 5680 135-281 930-1935 3000 6 6 1 FM Approved


1000 3785 65-137 450-945 1780 6 6 1 FM Approved


1000 3785 63-142 435-980 2100 6 6 1 FM Approved


1000 3785 93-186 640-1280 2100 6 6 1 FM Approved


1000 3785 84-173 580-1190 2300 6 6 1 FM Approved


1000 3785 108-225 745-1550 2300 6 6 1 FM Approved


1000 3785 251 1730 2880 6 6 1 FM Approved


1000 3785 150 1035 3000 6 6 1 FM Approved


America

1000 3785 155-299 580-2060 3000 6 6 1 FM Approved


1000 3785 238 1640 3580 6 6 1 FM Approved


750 2840 50-108 345-745 1800 6 6 1 FM Approved


500 1895 253 1745 3580 6 6 1 FM Approved


750 2840 73-155 505-1070 2100 6 6 1 FM Approved


750 2840 95-191 655-1315 2100 6 6 1 FM Approved

6x6 LDF

United

States of America

500 1895 97-197 670-1360 2100 6 6 1 FM Approved


500 1895 95-200 655-1380 2300 6 6 1 FM Approved


2000 7570 173-260 1195-1795 3000 6 6 1 FM Approved


500 1895 56-120 385-830 1800 6 6 1 FM Approved


500 1895 48-98 330-675 1500 6 6 1 FM Approved


500 1895 46-80 320-550 1500 6 6 1 FM Approved


7/21/2019 FM guide



500 1895 78-167 540-1150 2100 6 6 1 FM Approved


500 1895 112-237 770-1635 2300 6 6 1 FM Approved

6x6 LDF

United

States of America

750 2840 90-186 620-1280 2300 6 6 1 FM Approved


1250 4730 87 600 1500 6 6 1 FM Approved


1250 4730 62-133 430-915 1780 6 6 1 FM Approved


1250 4730 89-181 615-1250 2100 6 6 1 FM Approved


1250 4730 103-216 710-1490 2300 6 6 1 FM Approved


1250 4730 227 1565 3580 6 6 1 FM Approved


750 2840 110-232 760-1600 2300 6 6 1 FM Approved


750 2840 260 1795 2880 6 6 1 FM Approved


1250 4730 145-290 1000-2000 3000 6 6 1 FM Approved


750 2840 160-217 1105-1495 3000 6 6 1 FM Approved


750 2840 248 1710 3580 6 6 1 FM Approved

6x6DFUnitedStates of

America

1000 3785 41-89 283-614 2600 6 6 1 FM Approved


750 2840 47-106 324-731 2600 6 6 1 FM Approved


500 1895 49-115 338-793 2600 6 6 1 FM Approved


1500 5680 121 835 1490 8 6 2 FM Approved


1250 4730 184-344 1270-2370 2310 8 6 2 FM Approved


1500 5680 178-337 1225-2325 2310 8 6 2 FM Approved

8x6 TF

United

States of America

1500 5680 97-186 670-1280 1790 8 6 2 FM Approved


1000 3785 158-281 1090-1940 2100 8 6 2 FM Approved


1000 3785 190-353 1310-2435 2310 8 6 2 FM Approved


1000 3785 73-138 505-950 1490 8 6 2 FM Approved


1500 5680 145-268 1000-1850 2100 8 6 2 FM Approved


1000 3785 112-204 770-1405 1790 8 6 2 FM Approved


7/21/2019 FM guide



1500 5680 173-325 1195-2240 2300 8 6 2 FM Approved


1000 3785 186-342 1280-2360 2300 8 6 2 FM Approved

8x6 TF

United

States of America

1250 4730 71-130 490-895 1490 8 6 2 FM Approved


1250 4730 105-195 725-1345 1790 8 6 2 FM Approved


1250 4730 150-275 1035-1895 2100 8 6 2 FM Approved


1250 4730 180-333 1240-2295 2300 8 6 2 FM Approved


750 2840 100-225 690-1550 3300 8 8 1 FM Approved


750 2840 115-260 795-1795 3580 8 8 1 FM Approved


1250 4730 69-152 475-1050 2800 8 8 1 FM Approved


1250 4730 70-105 485-725 2350 8 8 1 FM Approved


1250 4730 78-179 540-1235 3000 8 8 1 FM Approved


750 2840 105-245 725-1690 3495 8 8 1 FM Approved


750 2840 40-65 275-450 1775 8 8 1 FM Approved


America

750 2840 81-188 560-1295 3000 8 8 1 FM Approved


500 1895 40-67 275-460 1775 8 8 1 FM Approved


1000 3785 80-184 550-1270 3000 8 8 1 FM Approved


1500 5680 68-95 470-655 2350 8 8 1 FM Approved


2000 7570 154-229 1060-1580 3580 8 8 1 FM Approved


1500 5680 71-169 490-1165 3000 8 8 1 FM Approved

8x8 DF

United

States of America

1250 4730 100-215 690-1480 3300 8 8 1 FM Approved


1500 5680 98-208 675-1435 3300 8 8 1 FM Approved


1500 5680 97-223 670-1540 3495 8 8 1 FM Approved


1250 4730 100-230 690-1585 3495 8 8 1 FM Approved


1500 5680 105-253 725-1745 3580 8 8 1 FM Approved


1000 3785 100-221 690-1525 3300 8 8 1 FM Approved


7/21/2019 FM guide



1250 4730 113-260 780-1795 3580 8 8 1 FM Approved


1000 3785 105-238 725-1640 3495 8 8 1 FM Approved

8x8 DF

United

States of America

1250 4730 43-61 295-420 1775 8 8 1 FM Approved


1000 3785 115-266 795-1835 3580 8 8 1 FM Approved


1000 3785 40-60 275-415 1775 8 8 1 FM Approved


1500 5680 123-312 848-2150 3000 8 8 1 FM Approved


1500 5680 100-210 690-1450 2300 8 8 1 FM Approved


2000 7570 43-115 295-795 1780 8 8 1 FM Approved


1500 5680 40-126 275-870 1780 8 8 1 FM Approved


2000 7570 49-78 338-538 1500 8 8 1 FM Approved


1250 4730 125-320 862-2206 3000 8 8 1 FM Approved


2000 7570 74-160 510-1105 2100 8 8 1 FM Approved


1250 4730 41-128 285-885 1780 8 8 1 FM Approved


America

2000 7570 93-200 690-1380 2300 8 8 1 FM Approved


2500 9465 63-149 435-1025 2100 8 8 1 FM Approved


1000 3785 54-125 370-860 1775 8 8 1 FM Approved


2000 7570 118-300 814-2070 3000 8 8 1 FM Approved


2500 9465 87-188 600-1295 2300 8 8 1 FM Approved


1500 5680 130 895 1800 8 8 1 FM Approved

8x8 LDF

United

States of America

1500 5680 55-85 380-586 1500 8 8 1 FM Approved


1500 5680 80-173 550-1195 2100 8 8 1 FM Approved


1500 5680 48-110 330-760 1775 8 8 1 FM Approved


1250 4730 52-117 360-805 1775 8 8 1 FM Approved


1250 4730 58-89 400-614 1500 8 8 1 FM Approved


2000 7570 125 860 1800 8 8 1 FM Approved


7/21/2019 FM guide



1000 3785 73-128 503-883 2600 8 8 1 FM Approved


1250 4730 70-123 483-848 2600 8 8 1 FM Approved

8x8DF

United

States of America

1500 5680 62-113 427-779 2600 8 8 1 FM Approved

Ruhrpumpen, S.A. DE C.V.Niquel No. 9204, Ciudad Industrias Mitras, Garcia, N.L. Mexico 66000





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

HSD 4 x3 x 17

Mexico 250 946 94-151 645-1041 1750 4 3 1 FM Approved

HSR 4 x6 x 11B


HSD 6 x

4 x 17Mexico 750 2839 93-143 641-986 1750 6 4 1 FM Approved

HSD 8 x6 x 20 * Mexico 750 2839 108-197 745-1358 1750 8 6 1 FM Approved

HSD 8 x6 x 17



HSD 8 x6 x 17



HSD 8 x6 x 17


HSC 8 x12 x 18A*



HSD 10x 8 x 20


HSD 10x 8 x 17


HSC 8 x12 x 18A*


HSD 10x 8 x 20


HSC 8 x12 x 18A*


HSC 8 x14 x 21E*


HSC 8 x14 x 21E*


* These pumps available with special materials for use in nonpotable water applications.

S.A. Armstrong Ltd23 Bertrand Ave, Scarborough, Ontario M1L 2P3, CAN





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

5x4x12HF Canada 500 1895 41-63 285-435 1780 5 4 1 FM Approved


5x4-10F Canada 500 1895 41-92 285-635 2600 5 4 1 FM Approved


7/21/2019 FM guide







BP-F Canada 500 1895 75-135 515-930 1760 5 4 1 FM Approved

8x6x16F Canada 750 2840 40-76 276-524 1450 8 6 1 FM Approved


6x5x9.5F Canada 750 2840 47-67 324-462 2600 6 5 1 FM Approved



6x5x12MF Canada 750 2840 56-115 386-793 2350 6 5 1 FM Approved












5x4-12HF Canada 750 2840 84-107 580-740 2350 5 4 1 FM Approved



BP-F Canada 750 2840 95-125 655-860 1760 5 4 1 FM Approved









8x6-10LF Canada 1000 3785 60-93 415-640 2600 8 6 1 FM Approved




















8x6x12-1/2HF Canada 1250 4730 40-73 275-505 1780 8 6 1 FM Approved


8x6x12-1/2MF Canada 1250 4730 51-78 352-538 2350 8 6 1 FM Approved


8x6x12-1/2HF Canada 1250 4730 58-106 400-730 2100 8 6 1 FM Approved

8x6x10LF Canada 1250 4730 74-120 510-825 2945 8 6 1 FM Approved


7/21/2019 FM guide


7/21/2019 FM guide





12x8x18F Canada 3000 11,355 79-131 545-905 1780 12 8 1 FM Approved

SPP Pumps Inc6710 Best Friend Road, Norcross, Georgia 30071, USA





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

TB08D †UnitedStates of America

200 755 96-149 660-1025 3550 4 3 1 FM Approved

TD10E †UnitedStates of America

200 755 98-169 675-1165 2950 5 4 1 FM Approved


200 755 109-187 750-1290 3100 5 4 1 FM Approved

TD10E † UnitedStates of America

200 755 140-210 965-1450 3550 5 4 1 FM Approved

PB02B *UnitedStates of America

250 945 40-100 275-690 3530 3 2 1 FM Approved


250 945 94-147 650-1015 3550 4 3 1 FM Approved


250 945 97-168 670-1160 2950 5 4 1 FM Approved


250 945 108-186 745-1280 3100 5 4 1 FM Approved


250 945 139-209 960-1440 3550 5 4 1 FM Approved


300 1135 93-145 640-1000 3550 4 3 1 FM Approved


300 1135 96-167 660-1150 2950 5 4 1 FM Approved


300 1135 106-185 730-1275 3100 5 4 1 FM Approved


300 1135 138-208 950-1435 3550 5 4 1 FM Approved


400 1515 87-139 600-960 3550 4 3 1 FM Approved

TD10E†

United

States of America 400 1515 92-164 635-1130 2950 5 4 1 FM Approved


400 1515 102-182 705-1255 3100 5 4 1 FM Approved


400 1515 105-144 725-995 3550 6 4 1 FM Approved


400 1515 134-205 925-1415 3550 5 4 1 FM Approved

PC05H *UnitedStates of America

500 1895 40-66 255-455 1460 6 5 1 FM Approved

PC04D *UnitedStates of America

500 1895 40-50 270-345 1760 5 4 1 FM Approved


7/21/2019 FM guide


TC12FUnitedStates of America

500 1895 43-49 295-340 1760 6 5 1 FM Approved

TE10DUnitedStates of America

500 1895 44-90 305-620 1760 5 4 1 FM Approved

PC04C *

United

States of America

500 1895 45-60 310-415 1760 5 4 1 FM Approved


500 1895 48-72 330-495 2100 6 5 1 FM Approved

PC04B *UnitedStates of America

500 1895 48-80 330-550 2950 5 4 1 FM Approved

PC06C *UnitedStates of America

500 1895 50-70 345-485 1760 8 6 1 FM Approved

PC05K *UnitedStates of America

500 1895 50-80 345-550 1760 6 5 1 FM Approved


500 1895 50-84 345-580 3000 5 4 1 FM Approved

PC04E *UnitedStates of America

500 1895 50-86 345-595 2100 5 4 1 FM Approved


500 1895 53-92 365-635 2350 6 5 1 FM Approved

TB08EUnitedStates of America

500 1895 54-104 370-715 3550 4 3 1 FM Approved


500 1895 54-120 370-825 3525 5 4 1 FM Approved


500 1895 65-111 450-765 2350 5 4 1 FM Approved

TE10D †UnitedStates of

America

500 1895 65-122 450-840 2100 5 4 1 FM Approved

TD10EUnitedStates of America

500 1895 66-99 455-685 2350 5 4 1 FM Approved


500 1895 67-113 460-780 2600 6 5 1 FM Approved


500 1895 68-124 470-855 2600 5 4 1 FM Approved

TE12E †UnitedStates of America

500 1895 72-131 495-905 2100 6 5 1 FM Approved

TE10D †UnitedStates of America

500 1895 72-137 495-945 2200 5 4 1 FM Approved

TB10E

United

States of America

500 1895 80-108 550-745 3550 6 4 1 FM Approved


500 1895 80-143 550-985 2200 6 5 1 FM Approved


500 1890 81-133 560-915 3550 4 3 1 FM Approved


500 1895 81-150 560-1035 2300 5 4 1 FM Approved


500 1895 86-158 595-1090 2950 5 4 1 FM Approved


500 1895 87-158 600-1090 2300 6 5 1 FM Approved


7/21/2019 FM guide



500 1895 87-162 600-1115 2400 5 4 1 FM Approved

PC04A *UnitedStates of America

500 1895 90-100 620-690 2800 5 4 1 FM Approved

PC04A *

United

States of America

500 1895 90-145 620-1000 3300 5 4 1 FM Approved


500 1895 93-116 640-800 2950 5 4 1 FM Approved


500 1895 95-120 655-825 3000 5 4 1 FM Approved


500 1895 95-130 655-895 3525 4 3 1 FM Approved


500 1895 95-170 655-1170 3550 5 4 1 FM Approved


500 1895 96-176 660-1215 2500 5 4 1 FM Approved


500 1895 97-171 670-1180 2400 6 5 1 FM Approved


500 1895 97-176 670-1215 3100 5 4 1 FM Approved

PD04A *UnitedStates of America

500 1895 100-175 690-1205 1770 5 4 2 FM Approved


500 1890 102-139 705-960 3550 6 4 1 FM Approved


500 1895 104-177 715-1220 2950 5 4 1 FM Approved

TE12E †UnitedStates of

America

500 1895 104-187 715-1290 2500 6 5 1 FM Approved


500 1895 104-193 715-1330 2600 5 4 1 FM Approved


500 1890 112-148 770-1020 3550 6 5 1 FM Approved


500 1895 112-181 770-1250 3000 5 4 1 FM Approved

TC12F †UnitedStates of America

500 1890 118-208 815-1435 3550 6 5 1 FM Approved


500 1895 121-190 835-1310 1760 6 5 2 FM Approved

TE10D †

United

States of America

500 1895 121-229 835-1580 2800 5 4 1 FM Approved


500 1895 125-145 860-1000 3525 4 3 1 FM Approved


500 1890 129-200 890-1380 3550 5 4 1 FM Approved


500 1895 131-247 905-1705 2900 5 4 1 FM Approved


500 1895 135-255 930-1760 2950 5 4 1 FM Approved

TC12G †UnitedStates of America

500 1890 138-193 950-1330 3550 6 5 1 FM Approved


7/21/2019 FM guide



500 1895 138-220 950-1515 3300 5 4 1 FM Approved


500 1895 141-264 970-1820 3000 5 4 1 FM Approved

TE10A †

United

States of America

500 1895 144-219 995-1510 2950 5 4 1 FM Approved

TY12D †UnitedStates of America

500 1895 145-191 1000-1317 1760 6 5 2 FM Approved

PD04K *UnitedStates of America

500 1895 158-269 1090-1855 2800 6 4 2 FM Approved


500 1895 160-264 1105-1820 3550 5 4 1 FM Approved

TY15EUnitedStates of America

500 1895 171-210 1080-1450 1760 8 6 2 FM Approved


500 1895 173-223 1193-1538 1900 6 5 2 FM Approved


500 1895 173-277 1195-1910 2100 6 5 2 FM Approved


500 1895 177-300 1220-2070 2950 6 4 2 FM Approved


500 1895 183-312 1260-2150 3000 6 4 2 FM Approved


500 1895 195-242 1345-1670 1900 8 6 2 FM Approved


500 1895 214-276 1475-1903 2100 6 5 2 FM Approved

PD04K *UnitedStates of

America

500 1895 229-384 1580-2650 3300 6 4 2 FM Approved


500 1895 240-298 1655-2055 2100 8 6 2 FM Approved

TX12D †UnitedStates of America

500 1895 256-330 1765-2275 2950 6 5 2 FM Approved


500 1895 260-334 1793-2303 2300 6 5 2 FM Approved


500 1895 272-446 1875-3075 3550 6 4 2 FM Approved


500 1895 273-350 1882-2413 2350 6 5 2 FM Approved

TX15E

United

States of America

500 1895 277-370 1850-2480 2950 8 6 2 FM Approved

TX15FUnitedStates of America

500 1895 283-378 1950-2610 2950 8 6 2 FM Approved


500 1895 288-360 1985-2480 2300 8 6 2 FM Approved


500 1895 300-375 2070-2590 2350 8 6 2 FM Approved


750 2840 40-56 275-385 1760 5 4 1 FM Approved

TD12FUnitedStates of America

750 2840 44-54 305-370 1760 6 5 1 FM Approved


7/21/2019 FM guide



750 2840 47-67 325-460 2950 6 5 1 FM Approved


750 2840 47-71 325-490 1760 8 6 1 FM Approved

PC05B *

United

States of America

750 2840 48-70 330-485 3000 6 5 1 FM Approved


750 2840 49-81 340-560 2100 6 5 1 FM Approved


750 2840 50-94 345-650 1760 6 5 1 FM Approved


750 2840 54-75 370-515 2950 6 5 1 FM Approved


750 2840 54-82 370-565 2350 6 5 1 FM Approved


750 2840 55-78 380-540 3000 6 5 1 FM Approved


750 2840 59-104 405-715 2600 6 5 1 FM Approved


750 2840 60-105 415-725 3565 6 5 1 FM Approved


750 2840 60-106 415-730 3500 6 5 1 FM Approved


750 2840 60-111 415-765 3550 6 5 1 FM Approved


750 2840 62-103 425-710 2350 6 5 1 FM Approved

TE10D †UnitedStates of

America

750 2840 62-122 425-840 2200 5 4 1 FM Approved


750 2840 65-123 450-850 2800 6 5 1 FM Approved


750 2840 69-95 475-655 3550 6 4 1 FM Approved


750 2840 69-137 475-945 2300 5 4 1 FM Approved


750 2840 70-96 485-660 3300 6 5 1 FM Approved


750 2840 70-100 485-690 3565 6 5 1 FM Approved

TE12E †

United

States of America

750 2840 70-134 485-925 2200 6 5 1 FM Approved


750 2840 74-134 510-925 2950 6 5 1 FM Approved


750 2840 77-149 530-1025 2400 5 4 1 FM Approved


750 2840 78-148 540-1020 2300 6 5 1 FM Approved


750 2840 80-159 550-1095 3500 5 4 1 FM Approved


750 2840 82-108 565-745 2100 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 82-139 565-960 3300 5 4 1 FM Approved


750 2840 83-93 570-640 2800 5 4 1 FM Approved

PC04A *

United

States of America

750 2840 83-107 570-740 2950 5 4 1 FM Approved


750 2840 84-164 580-1130 3550 5 4 1 FM Approved


750 2840 85-113 585-780 3550 6 5 1 FM Approved


750 2840 85-164 585-1130 2500 5 4 1 FM Approved


750 2840 86-110 595-760 3000 5 4 1 FM Approved


750 2840 88-162 605-1115 2400 6 5 1 FM Approved


750 2840 90-121 620-835 2100 6 5 1 FM Approved

TD12F †UnitedStates of America

750 2840 95-165 655-1140 2950 6 5 1 FM Approved


750 2840 94-179 650-1235 2600 5 4 1 FM Approved


750 2840 95-129 655-890 3550 6 4 1 FM Approved

BS06A†, **


750 2840 95-135 655-930 2450-3000 8 6 1 FM Approved

PC04E *UnitedStates of

America

750 2840 95-164 655-1130 2950 5 4 1 FM Approved


750 2840 97-178 670-1225 2500 6 5 1 FM Approved

BS06A †UnitedStates of America

750 2840 100-150 690-1035 2970 8 6 1 FM Approved


750 2840 100-170 690-1170 3000 5 4 1 FM Approved


750 2840 101-180 695-1240 1770 6 5 2 FM Approved


750 2840 105-193 725-1330 2600 6 5 1 FM Approved

TB12D †

United

States of America

750 2840 106-144 730-990 3550 6 5 1 FM Approved


750 2840 111-142 765-980 2950 6 5 1 FM Approved


750 2840 111-199 765-1370 3550 6 5 1 FM Approved


750 2840 112-216 770-1490 2800 5 4 1 FM Approved


750 2840 121-233 835-1605 2900 5 4 1 FM Approved


750 2840 124-227 855-1565 2800 6 5 1 FM Approved


7/21/2019 FM guide



750 2840 124-243 855-1675 2950 5 4 1 FM Approved


750 2840 125-207 860-1425 3300 8 6 1 FM Approved

PC05H *

United

States of America

750 2840 130-138 895-950 2100 6 5 1 FM Approved


750 2840 130-185 895-1275 3550 6 5 1 FM Approved


750 2840 131-252 905-1735 3000 5 4 1 FM Approved

PC05G *UnitedStates of America

750 2840 136-180 940-1240 2950 6 5 1 FM Approved

TE10A †UnitedStates of America

750 2840 136-213 940-1470 2950 5 4 1 FM Approved


750 2840 136-245 940-1690 2900 6 5 1 FM Approved


750 2840 141-186 970-1280 3000 6 5 1 FM Approved


750 2840 141-208 970-1435 3550 6 5 1 FM Approved


750 2840 141-255 970-1760 2950 6 5 1 FM Approved


750 2840 146-264 1005-1820 3000 6 5 1 FM Approved


750 2840 147-251 1015-1730 3550 5 4 1 FM Approved

PC05G *UnitedStates of

America

750 2840 156-234 1075-1615 3300 6 5 1 FM Approved


750 2840 163-200 1124-1379 1900 6 5 2 FM Approved


750 2840 164-173 1130-1195 2350 6 5 1 FM Approved


750 2840 165-265 1140-1825 2100 6 5 2 FM Approved


750 2840 166-205 1145-1415 1760 8 6 2 FM Approved


750 2840 173-180 1195-1240 2400 6 5 1 FM Approved

PC05G *

United

States of America

750 2840 184-268 1270-1850 3550 6 5 1 FM Approved


750 2840 190-237 1310-1635 1900 8 6 2 FM Approved


750 2840 190-250 1310-1724 2100 6 5 2 FM Approved

TX12D †UnitedStates of America

750 2840 230-300 1585-2070 2950 6 5 2 FM Approved


750 2840 235-294 1620-2030 2100 8 6 2 FM Approved


750 2840 240-312 1655-2151 2300 6 5 2 FM Approved


7/21/2019 FM guide



750 2840 250-328 1724-2262 2350 6 5 2 FM Approved

TX15EUnitedStates of America

750 2840 268-360 1850-2480 2950 8 6 2 FM Approved

TX15F

United

States of America

750 2840 276-370 1905-2550 2950 8 6 2 FM Approved


750 2840 284-353 1960-2435 2300 8 6 2 FM Approved


750 2840 296-370 2040-2550 2350 8 6 2 FM Approved


1000 3785 43-53 295-365 1760 8 6 1 FM Approved

TE15EUnitedStates of America

1000 3785 44-79 305-545 1760 8 6 1 FM Approved


1000 3785 44-85 305-585 1760 8 6 1 FM Approved


1000 3785 54-87 370-600 1760 8 6 1 FM Approved


1000 3785 55-86 380-595 1460 8 6 1 FM Approved


1000 3785 57-95 395-655 2350 6 5 1 FM Approved


1000 3785 60-73 415-505 2100 6 5 1 FM Approved


1000 3785 60-106 415-730 3550 6 5 1 FM Approved

PC05B *UnitedStates of

America

1000 3785 65-95 450-655 3565 6 5 1 FM Approved


1000 3785 70-108 485-745 2800 8 6 1 FM Approved


1000 3785 70-130 485-895 2950 6 5 1 FM Approved


1000 3785 72-121 495-835 2600 6 5 1 FM Approved

PC06J *UnitedStates of America

1000 3785 74-113 510-780 1780 8 6 1 FM Approved


1000 3785 74-128 510-883 2600 8 6 1 FM Approved

PC05E *

United

States of America

1000 3785 75-135 515-930 3000 6 5 1 FM Approved


1000 3785 77-114 530-785 2950 8 6 1 FM Approved


1000 3785 79-107 545-740 3550 6 5 1 FM Approved


1000 3785 82-121 565-835 3000 8 6 1 FM Approved

PC05F *UnitedStates of America

1000 3785 84-165 580-1140 3300 6 5 1 FM Approved


1000 3785 85-100 585-690 3565 6 5 1 FM Approved


7/21/2019 FM guide


TF15E †UnitedStates of America

1000 3785 85-145 585-1000 1760 8 6 1 FM Approved


1000 3785 89-105 615-725 3550 6 5 1 FM Approved

TD12F †

United

States of America

1000 3785 89-159 615-1095 2950 6 5 1 FM Approved


1000 3785 90-157 620-1080 2800 8 6 1 FM Approved

BS06A†, **


1000 3785 93-130 640-895 2450-3000 8 6 1 FM Approved


1000 3785 95-165 655-1140 3300 6 5 1 FM Approved


1000 3785 97-171 670-1180 2950 8 6 1 FM Approved


1000 3785 97-190 670-1310 3500 6 5 1 FM Approved


1000 3785 99-137 680-945 3550 6 5 1 FM Approved


1000 3785 100-131 690-905 2950 6 5 1 FM Approved


1000 3785 100-150 690-1035 2970 8 6 1 FM Approved


1000 3785 100-195 690-1340 3550 6 5 1 FM Approved


1000 3785 101-147 695-1015 3300 8 6 1 FM Approved

TF15E †UnitedStates of

America

1000 3785 101-171 695-1180 1900 8 6 1 FM Approved


1000 3785 102 705 2300 8 6 1 FM Approved


1000 3785 103-169 710-1165 3550 8 6 1 FM Approved

TB12FUnitedStates of America

1000 3785 104-144 715-995 3550 6 5 1 FM Approved


1000 3785 115-153 795-1055 3550 8 6 1 FM Approved


1000 3785 115-210 795-1450 1770 8 6 2 FM Approved

PC06L *

United

States of America

1000 3785 119-145 820-1000 1770 8 6 1 FM Approved


1000 3785 119-175 820-1205 3550 6 5 1 FM Approved


1000 3785 123-232 850-1600 2900 6 5 1 FM Approved


1000 3785 126-208 870-1435 2100 8 6 1 FM Approved


1000 3785 128-175 880-1205 2950 6 5 1 FM Approved


1000 3785 128-240 885-1655 2950 6 5 1 FM Approved


7/21/2019 FM guide



1000 3785 132-181 910-1250 2600 6 5 1 FM Approved


1000 3785 132-181 910-1250 3000 6 5 1 FM Approved

TD12F †

United

States of America

1000 3785 134-199 925-1370 3550 6 5 1 FM Approved


1000 3785 134-250 925-1725 3000 6 5 1 FM Approved


1000 3785 139-228 960-1570 2200 8 6 1 FM Approved


1000 3785 145-165 1000-1140 3550 8 6 1 FM Approved


1000 3785 145-222 1000-1530 3300 6 5 1 FM Approved


1000 3785 152-251 1050-1730 2300 8 6 1 FM Approved


1000 3785 155-167 1070-1150 2350 6 5 1 FM Approved


1000 3785 155-196 1070-1350 1760 8 6 2 FM Approved


1000 3785 159-213 1095-1470 2800 6 5 1 FM Approved


1000 3785 160-251 1100-1730 2350 8 6 1 FM Approved


1000 3785 165-176 1140-1215 2400 6 5 1 FM Approved

PC05G *UnitedStates of

America

1000 3785 170-260 580-1140 3500 6 5 1 FM Approved

PC06L *UnitedStates of America

1000 3785 171-205 1180-1415 2100 8 6 1 FM Approved


1000 3785 172-262 1185-1805 3550 6 5 1 FM Approved


1000 3785 181-230 1250-1585 1900 8 6 2 FM Approved


1000 3785 227-285 1565-1965 2100 8 6 2 FM Approved


1000 3785 254-346 1750-2385 2950 8 6 2 FM Approved

TX15F

United

States of America

1000 3785 268-361 1850-2490 2950 8 6 2 FM Approved


1000 3785 278-345 1915-2380 2300 8 6 2 FM Approved


1000 3785 291-361 2010-2490 2350 8 6 2 FM Approved


1250 4730 40-82 275-565 1760 8 6 1 FM Approved


1250 4730 50-81 345-560 1760 8 6 1 FM Approved


1250 4730 55-82 380-565 1460 8 6 1 FM Approved


7/21/2019 FM guide


TE15EUnitedStates of America

1250 4730 59-74 405-510 1760 8 6 1 FM Approved


1250 4730 60-127 415-875 1780 8 6 1 FM Approved

TD15F

United

States of America

1250 4730 62-100 425-690 2350 8 6 1 FM Approved


1250 4730 65-103 450-710 2800 8 6 1 FM Approved


1250 4730 70-123 483-848 2600 8 6 1 FM Approved


1250 4730 74-110 510-760 2950 8 6 1 FM Approved


1250 4730 75-116 515-800 3000 8 6 1 FM Approved


1250 4730 81-142 560-980 1760 8 6 1 FM Approved


1250 4730 82-148 565-1020 2950 6 5 1 FM Approved


1250 4730 84-150 580-1035 2800 8 6 1 FM Approved

BS06A†, **


1250 4730 87-130 600-895 2450-3000 9 6 1 FM Approved


1250 4730 90-169 620-1165 2800 8 6 1 FM Approved


1250 4730 93-164 640-1130 2950 8 6 1 FM Approved

TD15F †UnitedStates of

America

1250 4730 95 655 2300 8 6 1 FM Approved


1250 4730 96-174 660-1200 2800 10 8 1 FM Approved


1250 4730 97-142 670-980 3300 8 6 1 FM Approved


1250 4730 97-164 670-1130 3550 8 6 1 FM Approved


1250 4730 97-166 670-1145 1900 8 6 1 FM Approved

TB12FUnitedStates of America

1250 4730 98-132 675-910 3550 6 5 1 FM Approved

BS06A †

United

States of America

1250 4730 100-150 690-1035 2970 8 6 1 FM Approved


1250 4730 100-182 690-1255 2950 8 6 1 FM Approved


1250 4730 104-186 715-1280 3000 8 6 1 FM Approved


1250 4730 108-196 745-1350 2950 10 8 1 FM Approved


1250 4730 110-145 760-1000 1770 8 6 1 FM Approved


1250 4730 111-150 765-1035 3550 8 6 1 FM Approved


7/21/2019 FM guide



1250 4730 122-203 840-1400 2100 8 6 1 FM Approved


1250 4730 125-191 860-1315 3550 6 5 1 FM Approved

PC06C *

United

States of America

1250 4730 126-229 870-1580 3300 8 6 1 FM Approved


1250 4730 134-225 925-1550 2200 8 6 1 FM Approved


1250 4730 137-191 945-1315 3550 8 6 1 FM Approved


1250 4730 142-160 980-1105 3550 8 6 1 FM Approved


1250 4730 148-246 1020-1695 2300 8 6 1 FM Approved


1250 4730 152-273 1050-1880 3550 8 6 1 FM Approved


1250 4730 155-246 1070-1695 2350 8 6 1 FM Approved


1250 4730 165-205 1140-1415 2100 8 6 1 FM Approved


1250 4730 170-215 1170-1480 1900 8 6 2 FM Approved


1250 4730 214-274 1475-1890 2100 8 6 2 FM Approved

TX15FUnitedStates of America

1250 4730 246-348 1695-2400 2950 8 6 2 FM Approved

TY15EUnitedStates of

America

1250 4730 265-331 1830-2280 2300 8 6 2 FM Approved


1250 4730 275-329 1895-2270 2950 8 6 2 FM Approved


1250 4730 278-347 1920-2390 2350 8 6 2 FM Approved


1500 5680 40-63 275-435 1470 10 8 1 FM Approved


1500 5680 40-77 275-530 1760 10 8 1 FM Approved


1500 5680 41-55 285-380 1760 10 8 1 FM Approved

TD20E

United

States of America

1500 5680 45-87 310-600 2100 10 8 1 FM Approved


1500 5680 45-86 310-595 1760 8 6 1 FM Approved

TD20DUnitedStates of America

1500 5680 47-60 325-415 1760 10 8 1 FM Approved


1500 5680 57-94 385-650 2350 8 6 1 FM Approved


1500 5680 64-116 441-800 2600 8 6 1 FM Approved


1500 5680 67-76 460-525 1760 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 72-112 495-770 2350 10 8 1 FM Approved


1500 5680 73-105 505-710 1470 10 8 1 FM Approved

TD15F †

United

States of America

1500 5680 78-144 535-990 2800 8 6 1 FM Approved

TF20FUnitedStates of America

1500 5680 81-140 560-965 1760 10 8 1 FM Approved


1500 5680 85-122 585-840 1780 8 6 1 FM Approved


1500 5680 88 605 2300 8 6 1 FM Approved


1500 5680 88-157 605-1080 2950 8 6 1 FM Approved


1500 5680 91-169 630-1165 2800 10 8 1 FM Approved

BS06C †UnitedStates of America

1500 5680 95-172 655-1185 2950 8 6 1 FM Approved


1500 5680 97-160 670-1105 3550 8 6 1 FM Approved


1500 5680 100-136 690-940 3300 8 6 1 FM Approved


1500 5680 105-140 725-965 1770 8 6 1 FM Approved


1500 5680 105-190 725-1310 2950 10 8 1 FM Approved

TF15E †UnitedStates of

America

1500 5680 108-136 745-940 1760 8 6 1 FM Approved


1500 5680 108-141 745-970 3550 8 6 1 FM Approved


1500 5680 108-177 745-1220 2950 8 6 1 FM Approved


1500 5680 110-160 760-1105 1780 10 8 1 FM Approved

TD20D †UnitedStates of America

1500 5680 110-179 760-1235 2800 10 8 1 FM Approved

BQ08E†, **


1500 5680 111-166 765-1145 1900-2300 10 8 1 FM Approved

PC06C *

United

States of America

1500 5680 112-180 770-1240 3000 8 6 1 FM Approved


1500 5680 115-162 795-1115 1900 8 6 1 FM Approved


1500 5680 116-199 800-1370 2100 8 6 1 FM Approved


1500 5680 120-160 825-1105 2800 8 6 1 FM Approved


1500 5680 121-220 835-1515 3300 8 6 1 FM Approved


1500 5680 128-220 885-1515 2200 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 133-187 915-1290 3550 8 6 1 FM Approved


1500 5680 139-155 960-1070 3550 8 6 1 FM Approved

TF15E †

United

States of America

1500 5680 143-241 985-1660 2300 8 6 1 FM Approved


1500 5680 147-268 1015-1850 3550 8 6 1 FM Approved


1500 5680 151-175 1040-1205 1770 10 8 2 FM Approved


1500 5680 151-243 1040-1675 2350 8 6 1 FM Approved


1500 5680 154-202 1060-1390 3550 10 8 1 FM Approved


1500 5680 160-202 1105-1390 2100 8 6 1 FM Approved


2000 7570 45-89 310-615 1780 10 8 1 FM Approved


2000 7570 54-94 370-650 1460 10 8 1 FM Approved


2000 7570 55-85 380-585 1470 10 8 1 FM Approved

TD25AUnitedStates of America

2000 7570 56-72 385-495 1760 10 10 1 FM Approved

TD20DUnitedStates of America

2000 7570 56-108 385-745 2350 10 8 1 FM Approved

TD20DUnitedStates of

America

2000 7570 58-82 400-565 2100 10 8 1 FM Approved


2000 7570 63-74 435-510 1760 10 8 1 FM Approved


2000 7570 63-101 435-695 2350 10 8 1 FM Approved


2000 7570 69-130 475-895 2100 10 8 1 FM Approved


2000 7570 69-130 475-895 2600 10 8 1 FM Approved


2000 7570 72-119 495-820 1470 10 8 1 FM Approved

TD20D

United

States of America

2000 7570 73-138 505-950 2600 10 8 1 FM Approved

TF20FUnitedStates of America

2000 7570 77-133 530-915 1760 10 8 1 FM Approved

TF20EUnitedStates of America

2000 7570 80-142 550-980 1760 10 8 1 FM Approved


2000 7570 84-159 580-1095 2800 10 8 1 FM Approved


2000 7570 87-140 600-965 2100 8 6 1 FM Approved


2000 7570 90-118 620-815 1780 10 8 1 FM Approved


7/21/2019 FM guide



2000 7570 91-164 625-1130 1475 10 8 1 FM Approved

BS08B †UnitedStates of America

2000 7570 94-150 650-1035 1475 10 8 1 FM Approved

TF20D

United

States of America

2000 7570 94-150 640-1035 1760 10 8 1 FM Approved


2000 7570 95-179 655-1235 2950 10 8 1 FM Approved


2000 7570 97-197 670-1360 2960 10 8 1 FM Approved


2000 7570 103-156 710-1015 1780 10 8 1 FM Approved


2000 7570 104-174 715-1200 2800 10 8 1 FM Approved

BQ08E†, **


2000 7570 108-160 745-1105 1900-2300 10 8 1 FM Approved


2000 7570 110-167 760-1150 2100 10 8 1 FM Approved


2000 7570 110-175 760-1205 1780 10 8 1 FM Approved


2000 7570 125-162 860-1115 2950 8 6 1 FM Approved


2000 7570 142-214 980-1475 1750 10 8 1 FM Approved


2000 7570 147-196 1015-1350 3550 10 8 1 FM Approved

PC08J *UnitedStates of

America

2000 7570 150-212 1035-1460 2100 10 8 1 FM Approved

TD25AUnitedStates of America

2500 9465 52-68 360-470 1760 10 10 1 FM Approved


2500 9465 52-98 360-675 1760 10 8 1 FM Approved


2500 9465 65-90 450-620 1460 10 8 1 FM Approved

TE25AUnitedStates of America

2500 9465 73-114 505-785 1760 12 10 1 FM Approved

TF20EUnitedStates of America

2500 9465 75-134 515-925 1760 10 8 1 FM Approved

TF20F

United

States of America

2500 9465 76-123 525-850 1760 10 8 1 FM Approved


2500 9465 80-125 550-860 1780 10 8 1 FM Approved


2500 9465 80-140 550-965 1780 10 8 1 FM Approved


2500 9465 85-127 585-875 1470 12 10 1 FM Approved


2500 9465 85-161 585-1110 1475 10 8 1 FM Approved

TF20DUnitedStates of America

2500 9465 87-146 600-1005 1760 10 8 1 FM Approved


7/21/2019 FM guide



2500 9465 95-164 655-1130 2800 10 8 1 FM Approved


2500 9465 100-141 690-970 1475 10 8 1 FM Approved

TD20D †

United

States of America

2500 9465 102-188 705-1295 2960 10 8 1 FM Approved

BQ08E†, **


2500 9465 103-155 710-1070 1900-2300 10 8 1 FM Approved


2500 9465 104-172 715-1185 1780 10 8 1 FM Approved


2500 9465 105-144 725-995 2800 10 8 1 FM Approved


2500 9465 105-155 725-1070 2100 10 8 1 FM Approved


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved


2500 9465 119-163 820-1125 2950 10 8 1 FM Approved


2500 9465 132-208 910-1435 1750 10 8 1 FM Approved


2500 9465 142-167 980-1150 1475 10 8 1 FM Approved


2500 9465 154-202 1060-1395 2100 10 8 1 FM Approved

BS08EUnitedStates of America

2500 9465 183 1262 1490 10 8 1 FM Approved

BT10DUnitedStates of

America

2500 9465 195-265 1345-1825 1480 12 10 1 FM Approved

TE25AUnitedStates of America

3000 11,355 69-111 475-765 1760 12 10 1 FM Approved

† These designations have (FM) following the designation number.* When requested, SPP can furnish pumps designed for applications where the suction pressures exceed 75 psi (515 kPa). These pumps are designated by the addition of the letter "H" after thetype designation.** These pumps are available for operation at any speed within the range shown. The intended operating speed should be specified when the pump is ordered.

SPP Pumps LimitedTheale Cross, Pincents Lane, Calcot Reading, Berkshire RG31 7SP, United Kingdom





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

TD10E † United

Kingdom

200 755 98-169 675-1165 2950 5 4 1 FM Approved

TB08D † UnitedKingdom

200 755 96-149 660-1025 3550 4 3 1 FM Approved

TD10E † UnitedKingdom

200 755 140-210 965-1450 3550 5 4 1 FM Approved


200 755 109-187 750-1290 3100 5 4 1 FM Approved

PB02B * UnitedKingdom

250 945 40-100 275-690 3530 3 2 1 FM Approved


250 945 97-168 670-1160 2950 5 4 1 FM Approved


250 945 94-147 650-1015 3550 4 3 1 FM Approved


250 945 108-186 745-1280 3100 5 4 1 FM Approved


7/21/2019 FM guide



250 945 139-209 960-1440 3550 5 4 1 FM Approved


300 1135 96-167 660-1150 2950 5 4 1 FM Approved


300 1135 93-145 640-1000 3550 4 3 1 FM Approved

TD10E †

United



300 1135 138-208 950-1435 3550 5 4 1 FM Approved


400 1515 92-164 635-1130 2950 5 4 1 FM Approved


400 1515 102-182 705-1255 3100 5 4 1 FM Approved


400 1515 134-205 925-1415 3550 5 4 1 FM Approved


400 1515 87-139 600-960 3550 4 3 1 FM Approved


400 1515 105-144 725-995 3550 6 4 1 FM Approved

PC04E * UnitedKingdom

500 1895 65-111 450-765 2350 5 4 1 FM Approved

PC04E* United


TC12FUnitedKingdom

500 1895 53-92 365-635 2350 6 5 1 FM Approved

TB08EUnitedKingdom

500 1895 54-104 370-715 3550 4 3 1 FM Approved


500 1895 104-177 715-1220 2950 5 4 1 FM Approved


500 1895 112-181 770-1250 3000 5 4 1 FM Approved


500 1895 138-220 950-1515 3300 5 4 1 FM Approved


500 1895 160-264 1105-1820 3550 5 4 1 FM Approved

PD04K * UnitedKingdom

500 1895 272-446 1875-3075 3550 6 4 2 FM Approved

PD04K* United



500 1895 183-312 1260-2150 3000 6 4 2 FM Approved


500 1895 177-300 1220-2070 2950 6 4 2 FM Approved


500 1895 158-269 1090-1855 2800 6 4 2 FM Approved

PD04A * UnitedKingdom

500 1895 100-175 690-1205 1770 5 4 2 FM Approved

PC04A * UnitedKingdom

500 1895 90-100 620-690 2800 5 4 1 FM Approved


500 1895 90-145 620-1000 3300 5 4 1 FM Approved

PC04B * UnitedKingdom

500 1895 54-120 370-825 3525 5 4 1 FM Approved

PC04A * United



500 1895 95-170 655-1170 3550 5 4 1 FM Approved


500 1895 125-145 860-1000 3525 4 3 1 FM Approved


500 1895 95-120 655-825 3000 5 4 1 FM Approved


500 1895 48-80 330-550 2950 5 4 1 FM Approved


500 1895 173-277 1195-1910 2100 6 5 2 FM Approved


500 1895 50-84 345-580 3000 5 4 1 FM Approved


500 1895 121-190 835-1310 1760 6 5 2 FM Approved


7/21/2019 FM guide



500 1895 95-130 655-895 3525 4 3 1 FM Approved

PC05K * UnitedKingdom

500 1895 50-80 345-550 1760 6 5 1 FM Approved


500 1895 86-158 595-1090 2950 5 4 1 FM Approved

TE10A †

United


TE10D † UnitedKingdom

500 1895 65-122 450-840 2100 5 4 1 FM Approved

TD10EUnitedKingdom

500 1895 66-99 455-685 2350 5 4 1 FM Approved

TC12FUnitedKingdom

500 1895 67-113 460-780 2600 6 5 1 FM Approved

TD10EUnitedKingdom

500 1895 68-124 470-855 2600 5 4 1 FM Approved


500 1895 72-137 495-945 2200 5 4 1 FM Approved

TB10EUnitedKingdom

500 1895 80-108 550-745 3550 6 4 1 FM Approved


500 1895 81-150 560-1035 2300 5 4 1 FM Approved

TE10D† United



500 1895 96-176 660-1215 2500 5 4 1 FM Approved


500 1895 104-193 715-1330 2600 5 4 1 FM Approved


500 1895 121-229 835-1580 2800 5 4 1 FM Approved


500 1895 131-247 905-1705 2900 5 4 1 FM Approved


500 1895 135-255 930-1760 2950 5 4 1 FM Approved


500 1895 141-264 970-1820 3000 5 4 1 FM Approved

TE12E † UnitedKingdom

500 1895 72-131 495-905 2100 6 5 1 FM Approved

TE12E† United



500 1895 87-158 600-1090 2300 6 5 1 FM Approved


500 1895 97-171 670-1180 2400 6 5 1 FM Approved


500 1895 104-187 715-1290 2500 6 5 1 FM Approved

TX12D † UnitedKingdom

500 1895 256-330 1765-2275 2950 6 5 2 FM Approved

TY12D † UnitedKingdom

500 1895 145-191 1000-1317 1760 6 5 2 FM Approved


500 1895 173-223 1193-1538 1900 6 5 2 FM Approved


500 1895 214-276 1475-1903 2100 6 5 2 FM Approved

TY12D † United



500 1895 273-350 1882-2413 2350 6 5 2 FM Approved

TX15EUnitedKingdom

500 1895 277-370 1850-2480 2950 8 6 2 FM Approved

TX15FUnitedKingdom

500 1895 283-378 1950-2610 2950 8 6 2 FM Approved

TY15EUnitedKingdom

500 1895 300-375 2070-2590 2350 8 6 2 FM Approved

TY15EUnitedKingdom

500 1895 288-360 1985-2480 2300 8 6 2 FM Approved

TY15EUnitedKingdom

500 1895 240-298 1655-2055 2100 8 6 2 FM Approved

TY15EUnitedKingdom

500 1895 195-242 1345-1670 1900 8 6 2 FM Approved


7/21/2019 FM guide


TY15EUnitedKingdom

500 1895 171-210 1080-1450 1760 8 6 2 FM Approved

PC06C * UnitedKingdom

500 1895 50-70 345-485 1760 8 6 1 FM Approved


500 1895 97-176 670-1215 3100 5 4 1 FM Approved

PC05H *

United


TC12G † UnitedKingdom

500 1890 138-193 950-1330 3550 6 5 1 FM Approved

TC12F † UnitedKingdom

500 1890 118-208 815-1435 3550 6 5 1 FM Approved


500 1890 112-148 770-1020 3550 6 5 1 FM Approved


500 1890 102-139 705-960 3550 6 4 1 FM Approved


500 1890 81-133 560-915 3550 4 3 1 FM Approved

PC04D * UnitedKingdom

500 1895 40-50 270-345 1760 5 4 1 FM Approved

TC12FUnitedKingdom

500 1895 43-49 295-340 1760 6 5 1 FM Approved

TE10D

United



500 1895 45-60 310-415 1760 5 4 1 FM Approved

TC12FUnitedKingdom

500 1895 48-72 330-495 2100 6 5 1 FM Approved


500 1890 129-200 890-1380 3550 5 4 1 FM Approved


750 2840 199-240 1370-1655 2800 6 4 2 FM Approved


750 2840 227-272 1565-1875 2950 6 4 2 FM Approved


750 2840 234-286 1615-1970 3000 6 4 2 FM Approved


750 2840 295-352 2035-2430 3300 6 4 2 FM Approved

PD04K* United


PD05L * UnitedKingdom

750 2840 183-311 1260-2145 1775 6 5 3 FM Approved

PC05H * UnitedKingdom

750 2840 173-180 1195-1240 2400 6 5 1 FM Approved


750 2840 164-173 1130-1195 2350 6 5 1 FM Approved

PC05G * UnitedKingdom

750 2840 184-268 1270-1850 3550 6 5 1 FM Approved


750 2840 156-234 1075-1615 3300 6 5 1 FM Approved


750 2840 165-265 1140-1825 2100 6 5 2 FM Approved


750 2840 147-251 1015-1730 3550 5 4 1 FM Approved

PC05G * United



750 2840 130-138 895-950 2100 6 5 1 FM Approved


750 2840 101-180 695-1240 1770 6 5 2 FM Approved


750 2840 136-180 940-1240 2950 6 5 1 FM Approved


750 2840 125-207 860-1425 3300 8 6 1 FM Approved


750 2840 95-164 655-1130 2950 5 4 1 FM Approved


750 2840 100-170 690-1170 3000 5 4 1 FM Approved


750 2840 83-93 570-640 2800 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 86-110 595-760 3000 5 4 1 FM Approved


750 2840 82-139 565-960 3300 5 4 1 FM Approved


750 2840 84-164 580-1130 3550 5 4 1 FM Approved

TB12E

United



750 2840 80-159 550-1095 3500 5 4 1 FM Approved


750 2840 83-107 570-740 2950 5 4 1 FM Approved


750 2840 124-227 855-1565 2800 6 5 1 FM Approved


750 2840 105-193 725-1330 2600 6 5 1 FM Approved


750 2840 97-178 670-1225 2500 6 5 1 FM Approved


750 2840 88-162 605-1115 2400 6 5 1 FM Approved


750 2840 78-148 540-1020 2300 6 5 1 FM Approved

TE12E† United



750 2840 90-121 620-835 2100 6 5 1 FM Approved


750 2840 131-252 905-1735 3000 5 4 1 FM Approved


750 2840 124-243 855-1675 2950 5 4 1 FM Approved


750 2840 121-233 835-1605 2900 5 4 1 FM Approved


750 2840 112-216 770-1490 2800 5 4 1 FM Approved


750 2840 82-108 565-745 2100 5 4 1 FM Approved


750 2840 55-78 380-540 3000 6 5 1 FM Approved

TC12F

United



750 2840 130-185 895-1275 3550 6 5 1 FM Approved


750 2840 60-105 415-725 3565 6 5 1 FM Approved


750 2840 111-199 765-1370 3550 6 5 1 FM Approved


750 2840 60-111 415-765 3550 6 5 1 FM Approved

TD12FUnitedKingdom

750 2840 62-103 425-710 2350 6 5 1 FM Approved


750 2840 62-122 425-840 2200 5 4 1 FM Approved


750 2840 65-123 450-850 2800 6 5 1 FM Approved

TB10EUnited



750 2840 106-144 730-990 3550 6 5 1 FM Approved


750 2840 69-137 475-945 2300 5 4 1 FM Approved


750 2840 95-129 655-890 3550 6 4 1 FM Approved


750 2840 77-149 530-1025 2400 5 4 1 FM Approved


750 2840 40-56 275-385 1760 5 4 1 FM Approved

TD12FUnitedKingdom

750 2840 44-54 305-370 1760 6 5 1 FM Approved


750 2840 85-164 585-1130 2500 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 47-71 325-490 1760 8 6 1 FM Approved


750 2840 47-67 325-460 2950 6 5 1 FM Approved


750 2840 48-70 330-485 3000 6 5 1 FM Approved

TD12F

United



750 2840 60-106 415-730 3500 6 5 1 FM Approved


750 2840 70-96 485-660 3300 6 5 1 FM Approved

TD12F † UnitedKingdom

750 2840 141-208 970-1435 3550 6 5 1 FM Approved


750 2840 70-100 485-690 3565 6 5 1 FM Approved


750 2840 50-94 345-650 1760 6 5 1 FM Approved


750 2840 54-75 370-515 2950 6 5 1 FM Approved

TC12FUnitedKingdom

750 2840 54-82 370-565 2350 6 5 1 FM Approved

TE10D† United



750 2840 136-245 940-1690 2900 6 5 1 FM Approved

BS06A†, **

UnitedKingdom

750 2840 95-135 655-930 2450-3000 8 6 1 FM Approved


750 2840 141-255 970-1760 2950 6 5 1 FM Approved

BS06A † UnitedKingdom

750 2840 100-150 690-1035 2970 8 6 1 FM Approved


750 2840 146-264 1005-1820 3000 6 5 1 FM Approved

TE10A † UnitedKingdom

750 2840 136-213 940-1470 2950 5 4 1 FM Approved


750 2840 95-165 655-1140 2950 6 5 1 FM Approved

TC12G† United



750 2840 74-134 510-925 2950 6 5 1 FM Approved


750 2840 163-200 1124-1379 1900 6 5 2 FM Approved


750 2840 190-250 1310-1724 2100 6 5 2 FM Approved

TX12D † UnitedKingdom

750 2840 230-300 1585-2070 2950 6 5 2 FM Approved


750 2840 240-312 1655-2151 2300 6 5 2 FM Approved


750 2840 250-328 1724-2262 2350 6 5 2 FM Approved

TX15EUnitedKingdom

750 2840 268-360 1850-2480 2950 8 6 2 FM Approved

TX15FUnited


TY15EUnitedKingdom

750 2840 296-370 2040-2550 2350 8 6 2 FM Approved

TY15EUnitedKingdom

750 2840 284-353 1960-2435 2300 8 6 2 FM Approved

TY15EUnitedKingdom

750 2840 235-294 1620-2030 2100 8 6 2 FM Approved

TY15EUnitedKingdom

750 2840 190-237 1310-1635 1900 8 6 2 FM Approved

TY15EUnitedKingdom

750 2840 166-205 1145-1415 1760 8 6 2 FM Approved

TD15FUnitedKingdom

1000 3785 43-53 295-365 1760 8 6 1 FM Approved

TE15EUnitedKingdom

1000 3785 44-79 305-545 1760 8 6 1 FM Approved


7/21/2019 FM guide



1000 3785 159-213 1095-1470 2800 6 5 1 FM Approved


1000 3785 132-181 910-1250 2600 6 5 1 FM Approved


1000 3785 97-171 670-1180 2950 8 6 1 FM Approved

TF15E †

United


TF15E † UnitedKingdom

1000 3785 152-251 1050-1730 2300 8 6 1 FM Approved


1000 3785 139-228 960-1570 2200 8 6 1 FM Approved


1000 3785 126-208 870-1435 2100 8 6 1 FM Approved


1000 3785 101-171 695-1180 1900 8 6 1 FM Approved


1000 3785 85-145 585-1000 1760 8 6 1 FM Approved


1000 3785 123-232 850-1600 2900 6 5 1 FM Approved


1000 3785 128-240 885-1655 2950 6 5 1 FM Approved

TE12E† United



1000 3785 90-157 620-1080 2800 8 6 1 FM Approved


1000 3785 74-128 510-883 2600 8 6 1 FM Approved


1000 3785 102 705 2300 8 6 1 FM Approved


1000 3785 100-131 690-905 2950 6 5 1 FM Approved


1000 3785 89-159 615-1095 2950 6 5 1 FM Approved

TX15EUnitedKingdom

1000 3785 254-346 1750-2385 2950 8 6 2 FM Approved

TX15FUnitedKingdom

1000 3785 268-361 1850-2490 2950 8 6 2 FM Approved

TY15E

United


TY15EUnitedKingdom

1000 3785 278-345 1915-2380 2300 8 6 2 FM Approved

TY15EUnitedKingdom

1000 3785 227-285 1565-1965 2100 8 6 2 FM Approved

TY15EUnitedKingdom

1000 3785 181-230 1250-1585 1900 8 6 2 FM Approved

TY15EUnitedKingdom

1000 3785 155-196 1070-1350 1760 8 6 2 FM Approved


1000 3785 100-150 690-1035 2970 8 6 1 FM Approved

BS06A†, **

UnitedKingdom

1000 3785 93-130 640-895 2450-3000 8 6 1 FM Approved


1000 3785 75-135 515-930 3000 6 5 1 FM Approved

PC05E * United


TD12FUnitedKingdom

1000 3785 72-121 495-835 2600 6 5 1 FM Approved


1000 3785 134-199 925-1370 3550 6 5 1 FM Approved

PC06J * UnitedKingdom

1000 3785 74-113 510-780 1780 8 6 1 FM Approved


1000 3785 70-108 485-745 2800 8 6 1 FM Approved


1000 3785 60-106 415-730 3550 6 5 1 FM Approved


1000 3785 55-86 380-595 1460 8 6 1 FM Approved

TD12FUnitedKingdom

1000 3785 57-95 395-655 2350 6 5 1 FM Approved


7/21/2019 FM guide


TD12FUnitedKingdom

1000 3785 60-73 415-505 2100 6 5 1 FM Approved


1000 3785 99-137 680-945 3550 6 5 1 FM Approved


1000 3785 165-176 1140-1215 2400 6 5 1 FM Approved

PC06A *

United



1000 3785 155-167 1070-1150 2350 6 5 1 FM Approved


1000 3785 128-175 880-1205 2950 6 5 1 FM Approved


1000 3785 115-210 795-1450 1770 8 6 2 FM Approved


1000 3785 77-114 530-785 2950 8 6 1 FM Approved

TB12EUnitedKingdom

1000 3785 79-107 545-740 3550 6 5 1 FM Approved


1000 3785 82-121 565-835 3000 8 6 1 FM Approved


1000 3785 101-147 695-1015 3300 8 6 1 FM Approved

PC06A* United


TB12FUnitedKingdom

1000 3785 104-144 715-995 3550 6 5 1 FM Approved

TB15EUnitedKingdom

1000 3785 115-153 795-1055 3550 8 6 1 FM Approved

PC05F * UnitedKingdom

1000 3785 100-195 690-1340 3550 6 5 1 FM Approved


1000 3785 85-100 585-690 3565 6 5 1 FM Approved


1000 3785 95-165 655-1140 3300 6 5 1 FM Approved


1000 3785 97-190 670-1310 3500 6 5 1 FM Approved


1000 3785 170-260 580-1140 3500 6 5 1 FM Approved

PC05G* United



1000 3785 132-181 910-1250 3000 6 5 1 FM Approved


1000 3785 172-262 1185-1805 3550 6 5 1 FM Approved

PC06L * UnitedKingdom

1000 3785 171-205 1180-1415 2100 8 6 1 FM Approved


1000 3785 119-145 820-1000 1770 8 6 1 FM Approved


1000 3785 44-85 305-585 1760 8 6 1 FM Approved

TE15DUnitedKingdom

1000 3785 54-87 370-600 1760 8 6 1 FM Approved


1000 3785 65-95 450-655 3565 6 5 1 FM Approved

TC12G † United



1000 3785 84-165 580-1140 3300 6 5 1 FM Approved


1000 3785 89-105 615-725 3550 6 5 1 FM Approved


1250 4730 97-164 670-1130 3550 8 6 1 FM Approved


1250 4730 65-103 450-710 2800 8 6 1 FM Approved


1250 4730 90-169 620-1165 2800 8 6 1 FM Approved


1250 4730 97-142 670-980 3300 8 6 1 FM Approved


1250 4730 40-82 275-565 1760 8 6 1 FM Approved


7/21/2019 FM guide


TE15DUnitedKingdom

1250 4730 50-81 345-560 1760 8 6 1 FM Approved


1250 4730 165-205 1140-1415 2100 8 6 1 FM Approved


1250 4730 152-273 1050-1880 3550 8 6 1 FM Approved

PC06A *

United



1250 4730 126-229 870-1580 3300 8 6 1 FM Approved


1250 4730 110-145 760-1000 1770 8 6 1 FM Approved

TB15EUnitedKingdom

1250 4730 111-150 765-1035 3550 8 6 1 FM Approved


1250 4730 104-186 715-1280 3000 8 6 1 FM Approved


1250 4730 100-182 690-1255 2950 8 6 1 FM Approved


1250 4730 60-127 415-875 1780 8 6 1 FM Approved

TD15FUnitedKingdom

1250 4730 62-100 425-690 2350 8 6 1 FM Approved

PC06A* United



1250 4730 75-116 515-800 3000 8 6 1 FM Approved


1250 4730 55-82 380-565 1460 8 6 1 FM Approved

TE15EUnitedKingdom

1250 4730 59-74 405-510 1760 8 6 1 FM Approved


1250 4730 134-225 925-1550 2200 8 6 1 FM Approved


1250 4730 137-191 945-1315 3550 8 6 1 FM Approved


1250 4730 125-191 860-1315 3550 6 5 1 FM Approved

BS06A†, **

UnitedKingdom

1250 4730 87-130 600-895 2450-3000 9 6 1 FM Approved

BS06A† United



1250 4730 82-148 565-1020 2950 6 5 1 FM Approved


1250 4730 108-196 745-1350 2950 10 8 1 FM Approved


1250 4730 95 655 2300 8 6 1 FM Approved


1250 4730 70-123 483-848 2600 8 6 1 FM Approved


1250 4730 96-174 660-1200 2800 10 8 1 FM Approved


1250 4730 84-150 580-1035 2800 8 6 1 FM Approved


1250 4730 81-142 560-980 1760 8 6 1 FM Approved

TF15E † United



1250 4730 93-164 640-1130 2950 8 6 1 FM Approved


1250 4730 97-166 670-1145 1900 8 6 1 FM Approved

TB12FUnitedKingdom

1250 4730 98-132 675-910 3550 6 5 1 FM Approved


1250 4730 122-203 840-1400 2100 8 6 1 FM Approved


1250 4730 155-246 1070-1695 2350 8 6 1 FM Approved

TX15EUnitedKingdom

1250 4730 275-329 1895-2270 2950 8 6 2 FM Approved

TX15FUnitedKingdom

1250 4730 246-348 1695-2400 2950 8 6 2 FM Approved


7/21/2019 FM guide


TY15EUnitedKingdom

1250 4730 278-347 1920-2390 2350 8 6 2 FM Approved

TY15EUnitedKingdom

1250 4730 265-331 1830-2280 2300 8 6 2 FM Approved

TY15EUnitedKingdom

1250 4730 214-274 1475-1890 2100 8 6 2 FM Approved

TY15E

United



1500 5680 115-162 795-1115 1900 8 6 1 FM Approved


1500 5680 116-199 800-1370 2100 8 6 1 FM Approved


1500 5680 108-136 745-940 1760 8 6 1 FM Approved

TB15EUnitedKingdom

1500 5680 108-141 745-970 3550 8 6 1 FM Approved


1500 5680 40-77 275-530 1760 10 8 1 FM Approved

TD20EUnitedKingdom

1500 5680 41-55 285-380 1760 10 8 1 FM Approved

TD20EUnitedKingdom

1500 5680 45-87 310-600 2100 10 8 1 FM Approved

TF15E† United



1500 5680 85-122 585-840 1780 8 6 1 FM Approved


1500 5680 160-202 1105-1390 2100 8 6 1 FM Approved


1500 5680 143-241 985-1660 2300 8 6 1 FM Approved


1500 5680 151-175 1040-1205 1770 10 8 2 FM Approved


1500 5680 105-140 725-965 1770 8 6 1 FM Approved


1500 5680 151-243 1040-1675 2350 8 6 1 FM Approved


1500 5680 147-268 1015-1850 3550 8 6 1 FM Approved

TD20E† United



1500 5680 88-157 605-1080 2950 8 6 1 FM Approved


1500 5680 139-155 960-1070 3550 8 6 1 FM Approved


1500 5680 121-220 835-1515 3300 8 6 1 FM Approved


1500 5680 120-160 825-1105 2800 8 6 1 FM Approved


1500 5680 112-180 770-1240 3000 8 6 1 FM Approved


1500 5680 110-160 760-1105 1780 10 8 1 FM Approved


1500 5680 108-177 745-1220 2950 8 6 1 FM Approved

TD15F † United



1500 5680 40-63 275-435 1470 10 8 1 FM Approved


1500 5680 78-144 535-990 2800 8 6 1 FM Approved

TF20FUnitedKingdom

1500 5680 81-140 560-965 1760 10 8 1 FM Approved


1500 5680 64-116 441-800 2600 8 6 1 FM Approved

TE15DUnitedKingdom

1500 5680 67-76 460-525 1760 8 6 1 FM Approved

TD20EUnitedKingdom

1500 5680 72-112 495-770 2350 10 8 1 FM Approved


1500 5680 100-136 690-940 3300 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 45-86 310-595 1760 8 6 1 FM Approved

TD20DUnitedKingdom

1500 5680 47-60 325-415 1760 10 8 1 FM Approved

TD15FUnitedKingdom

1500 5680 57-94 385-650 2350 8 6 1 FM Approved

TD15F †

United

Kingdom 1500 5680 88 605 2300 8 6 1 FM Approved


1500 5680 91-169 630-1165 2800 10 8 1 FM Approved

TD20D † UnitedKingdom

1500 5680 110-179 760-1235 2800 10 8 1 FM Approved

BS06C † UnitedKingdom

1500 5680 95-172 655-1185 2950 8 6 1 FM Approved


1500 5680 105-190 725-1310 2950 10 8 1 FM Approved

BQ08E†, **

UnitedKingdom

1500 5680 111-166 765-1145 1900-2300 10 8 1 FM Approved


1500 5680 97-160 670-1105 3550 8 6 1 FM Approved


1500 5680 73-105 505-710 1470 10 8 1 FM Approved

TD20D† United



2000 7570 95-179 655-1235 2950 10 8 1 FM Approved

TD20DUnitedKingdom

2000 7570 73-138 505-950 2600 10 8 1 FM Approved

TF20FUnitedKingdom

2000 7570 77-133 530-915 1760 10 8 1 FM Approved

TF20EUnitedKingdom

2000 7570 80-142 550-980 1760 10 8 1 FM Approved


2000 7570 84-159 580-1095 2800 10 8 1 FM Approved


2000 7570 147-196 1015-1350 3550 10 8 1 FM Approved


2000 7570 63-74 435-510 1760 10 8 1 FM Approved

TD20E

United



2000 7570 45-89 310-615 1780 10 8 1 FM Approved


2000 7570 54-94 370-650 1460 10 8 1 FM Approved


2000 7570 69-130 475-895 2100 10 8 1 FM Approved

TD20EUnitedKingdom

2000 7570 69-130 475-895 2600 10 8 1 FM Approved


2000 7570 87-140 600-965 2100 8 6 1 FM Approved


2000 7570 97-197 670-1360 2960 10 8 1 FM Approved


2000 7570 110-167 760-1150 2100 10 8 1 FM Approved

PC08K * United



2000 7570 150-212 1035-1460 2100 10 8 1 FM Approved


2000 7570 90-118 620-815 1780 10 8 1 FM Approved


2000 7570 55-85 380-585 1470 10 8 1 FM Approved

TD20DUnitedKingdom

2000 7570 56-108 385-745 2350 10 8 1 FM Approved

TD20DUnitedKingdom

2000 7570 58-82 400-565 2100 10 8 1 FM Approved


2000 7570 125-162 860-1115 2950 8 6 1 FM Approved


2000 7570 91-164 625-1130 1475 10 8 1 FM Approved


7/21/2019 FM guide


BS08B † UnitedKingdom

2000 7570 94-150 650-1035 1475 10 8 1 FM Approved

TF20DUnitedKingdom

2000 7570 94-150 640-1035 1760 10 8 1 FM Approved

TE20DUnitedKingdom

2000 7570 90-125 620-860 2100 10 8 1 FM Approved

BS08B †

United


BQ08E†, **

UnitedKingdom

2000 7570 108-160 745-1105 1900-2300 10 8 1 FM Approved


2000 7570 103-156 710-1015 1780 10 8 1 FM Approved


2000 7570 110-175 760-1205 1780 10 8 1 FM Approved

TE20DUnitedKingdom

2000 7570 115-160 1105-9795 2350 10 8 1 FM Approved


2500 9465 132-208 910-1435 1750 10 8 1 FM Approved


2500 9465 100-141 690-970 1475 10 8 1 FM Approved


2500 9465 105-144 725-995 2800 10 8 1 FM Approved

TD20D† United



2500 9465 85-161 585-1110 1475 10 8 1 FM Approved

TF20DUnitedKingdom

2500 9465 87-146 600-1005 1760 10 8 1 FM Approved

BQ08E†, **

UnitedKingdom

2500 9465 103-155 710-1070 1900-2300 10 8 1 FM Approved


2500 9465 142-167 980-1150 1475 10 8 1 FM Approved


2500 9465 119-163 820-1125 2950 10 8 1 FM Approved


2500 9465 85-127 585-875 1470 12 10 1 FM Approved


2500 9465 102-188 705-1295 2960 10 8 FM Approved

PC08K* United



2500 9465 154-202 1060-1395 2100 10 8 1 FM Approved


2500 9465 105-155 725-1070 2100 10 8 1 FM Approved


2500 9465 80-140 550-965 1780 10 8 1 FM Approved


2500 9465 80-125 550-860 1780 10 8 1 FM Approved


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved

TD25AUnitedKingdom

2500 9465 52-68 360-470 1760 10 10 1 FM Approved


2500 9465 52-98 360-675 1760 10 8 1 FM Approved

PC08F * United


TE25AUnitedKingdom

2500 9465 73-114 505-785 1760 12 10 1 FM Approved

TF20EUnitedKingdom

2500 9465 75-134 515-925 1760 10 8 1 FM Approved

TF20FUnitedKingdom

2500 9465 76-123 525-850 1760 10 8 1 FM Approved

TE25DUnitedKingdom

2500 9465 83-146 570-1005 2100 12 10 1 FM Approved

TE20DUnitedKingdom

2500 9465 84-117 580-805 2100 10 8 1 FM Approved

TE20DUnitedKingdom

2500 9465 109-153 750-1055 2350 10 8 1 FM Approved

BS08EUnitedKingdom

2500 9465 183 1262 1490 10 8 1 FM Approved


7/21/2019 FM guide


BT10DUnitedKingdom

2500 9465 195-265 1345-1825 1480 12 10 1 FM Approved

BS08EUnitedKingdom

3000 11,355 179 1234 1490 10 8 1 FM Approved


3000 11,355 85-188 585-1295 1780 12 10 1 FM Approved

PC10D *

United

Kingdom 3000 11,355 75-123 515-850 1775 12 10 1 FM Approved

TF20DUnitedKingdom

3000 11,355 82-138 565-950 1760 10 8 1 FM Approved


3000 11,355 100-151 690-1040 2100 10 8 1 FM Approved

BR12D † UnitedKingdom

3000 11,355 108-165 745-1140 1780 16 12 1 FM Approved

PA12F * UnitedKingdom

3000 11,355 118-164 815-1130 1760 14 12 1 FM Approved

TE25AUnitedKingdom

3000 11,355 69-111 475-765 1760 12 10 1 FM Approved


3000 11,355 72-113 495-780 1480 16 12 1 FM Approved


3000 11,355 83-117 570-805 1480 14 10 1 FM Approved

BR12C† United


BR12C † UnitedKingdom

3000 11,355 97-121 670-835 1480 16 12 1 FM Approved


3000 11,355 135-162 930-1115 1475 10 8 1 FM Approved

BQ08E†, **

UnitedKingdom

3000 11,355 120-150 825-1035 2100-2300 10 8 1 FM Approved


3000 11,355 102-210 705-1450 1900 12 10 1 FM Approved

BT10DUnitedKingdom

3000 11,355 187-256 1290-1765 1480 12 10 1 FM Approved

TE25DUnitedKingdom

3000 11,355 81-142 560-980 2100 12 10 1 FM Approved

TE20DUnitedKingdom

3000 11,355 100-145 690-1000 2350 10 8 1 FM Approved

BS10E

United


BS10EUnitedKingdom

3000 11,355 128-220 885-1515 1900 12 10 1 FM Approved


3500 13,250 73-120 505-825 1775 12 10 1 FM Approved


3500 13,250 96-119 660-820 1480 16 12 1 FM Approved


3500 13,250 80-115 550-795 1480 14 12 1 FM Approved


3500 13,250 105-163 725-1125 1780 16 12 1 FM Approved


3500 13,250 115-162 795-1115 1760 14 12 1 FM Approved


3500 13,250 120-182 860-1255 1780 12 10 1 FM Approved

BR12D † United

Kingdom3500 13,250 69-111 475-765 1480 16 12 1 FM Approved


3500 13,250 135-202 931-1393 1490 16 12 1 FM Approved


3500 13,250 95-206 655-1420 1900 12 10 1 FM Approved


3500 13,250 141-176 970-1215 1780 16 12 1 FM Approved

BT10DUnitedKingdom

3500 13,250 178-247 1225-1705 1480 12 10 1 FM Approved

TE25DUnitedKingdom

3500 13,250 78-137 540-945 2100 12 10 1 FM Approved

BS10EUnitedKingdom

3500 13,250 104-181 715-1250 1760 12 10 1 FM Approved

BS10EUnitedKingdom

3500 13,250 124-214 855-1475 1900 12 10 1 FM Approved


7/21/2019 FM guide



4000 15,140 139-174 960-1200 1780 16 12 1 FM Approved


4000 15,140 66-108 455-745 1480 16 12 1 FM Approved


4000 15,140 94-118 650-815 1480 16 12 1 FM Approved

BS12A †

United



4000 15,140 102-161 705-1110 1780 16 12 1 FM Approved


4000 15,140 78-112 540-770 1480 14 12 1 FM Approved


4000 15,140 112-161 770-1110 1760 14 12 1 FM Approved


4000 15,140 100-117 690-805 1775 12 10 1 FM Approved

BS10EUnitedKingdom

4000 15,140 119-208 820-1435 1900 12 10 1 FM Approved

BS10EUnitedKingdom

4000 15,140 128-173 885-1195 1760 12 10 1 FM Approved

BT10DUnitedKingdom

4000 15,140 168-237 1160-1635 1480 12 10 1 FM Approved

PA12F* United



4500 17,035 91-116 625-800 1480 16 12 1 FM Approved


4500 17,035 126-196 869-1351 1490 16 12 1 FM Approved


4500 17,035 136-172 940-1185 1780 16 12 1 FM Approved


4500 17,035 109-160 750-1105 1760 14 12 1 FM Approved


4500 17,035 63-105 435-725 1480 16 12 1 FM Approved


4500 17,035 93-114 640-785 1775 12 10 1 FM Approved


4500 17,035 99-158 685-1090 1780 16 12 1 FM Approved

BS12A† United



5000 18,925 108-157 730-1080 1760 14 12 1 FM Approved


5000 18,925 95-154 640-1065 1780 16 12 1 FM Approved

TB15FUnitedKingdom

1250 4730 95-143 655-985 3550 8 6 1 FM Approved

TB15FUnitedKingdom

1500 5680 91-136 625-940 3550 8 6 1 FM Approved

TF20GUnitedKingdom

1500 5680 71-138 490-950 1780 10 8 1 FM Approved

TF20GUnitedKingdom

2000 7570 65-127 450-875 1780 10 8 1 FM Approved

TE20AUnitedKingdom

2000 7570 50-94 345-650 1760 10 8 1 FM Approved

TE20AUnited


TE20DUnitedKingdom

2000 7570 62-81 425-560 1760 10 8 1 FM Approved

TD25AUnitedKingdom

2000 7570 46-68 315-470 1760 10 10 1 FM Approved

TD25AUnitedKingdom

2000 7570 41-72 285-495 1760 10 10 1 FM Approved

† These designations have (FM) following the designation number.* When requested, SPP can furnish pumps designed for applications where the suction pressures exceed 75 psi (515 kPa). These pumps are designated by the addition of the letter "H" after thetype designation.** These pumps are available for operation at any speed within the range shown. The intended operating speed should be specified when the pump is ordered.

SPP Pumps LimitedP. O. Box 61491, Jebel Ali, Dubai


7/21/2019 FM guide






psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

TD10E †United Arab

Emirates

200 755 98-169 675-1165 2950 5 4 1 FM Approved

TB08D †United ArabEmirates

200 755 96-149 660-1025 3550 4 3 1 FM Approved

TD10E †United ArabEmirates

200 755 140-210 965-1450 3550 5 4 1 FM Approved


200 755 109-187 750-1290 3100 5 4 1 FM Approved

PB02B *United ArabEmirates

250 945 40-100 275-690 3530 3 2 1 FM Approved


250 945 97-168 670-1160 2950 5 4 1 FM Approved


250 945 94-147 650-1015 3550 4 3 1 FM Approved


250 945 108-186 745-1280 3100 5 4 1 FM Approved


250 945 139-209 960-1440 3550 5 4 1 FM Approved


300 1135 96-167 660-1150 2950 5 4 1 FM Approved


300 1135 93-145 640-1000 3550 4 3 1 FM Approved


300 1135 106-185 730-1275 3100 5 4 1 FM Approved


300 1135 138-208 950-1435 3550 5 4 1 FM Approved


400 1515 92-164 635-1130 2950 5 4 1 FM Approved


400 1515 102-182 705-1255 3100 5 4 1 FM Approved


400 1515 134-205 925-1415 3550 5 4 1 FM Approved


400 1515 87-139 600-960 3550 4 3 1 FM Approved

TB10D †United Arab

Emirates

400 1515 105-144 725-995 3550 6 4 1 FM Approved

PC04E *United ArabEmirates

500 1895 65-111 450-765 2350 5 4 1 FM Approved


500 1895 50-86 345-595 2100 5 4 1 FM Approved

TC12FUnited ArabEmirates

500 1895 53-92 365-635 2350 6 5 1 FM Approved

TB08EUnited ArabEmirates

500 1895 54-104 370-715 3550 4 3 1 FM Approved


500 1895 104-177 715-1220 2950 5 4 1 FM Approved


7/21/2019 FM guide



500 1895 112-181 770-1250 3000 5 4 1 FM Approved


500 1895 138-220 950-1515 3300 5 4 1 FM Approved

PC04E *

United

ArabEmirates

500 1895 160-264 1105-1820 3550 5 4 1 FM Approved

PD04K *United ArabEmirates

500 1895 272-446 1875-3075 3550 6 4 2 FM Approved


500 1895 229-384 1580-2650 3300 6 4 2 FM Approved


500 1895 183-312 1260-2150 3000 6 4 2 FM Approved


500 1895 177-300 1220-2070 2950 6 4 2 FM Approved


500 1895 158-269 1090-1855 2800 6 4 2 FM Approved

PD04A *United ArabEmirates

500 1895 100-175 690-1205 1770 5 4 2 FM Approved

PC04A *United ArabEmirates

500 1895 90-100 620-690 2800 5 4 1 FM Approved


500 1895 90-145 620-1000 3300 5 4 1 FM Approved

PC04B *United ArabEmirates

500 1895 54-120 370-825 3525 5 4 1 FM Approved


500 1895 93-116 640-800 2950 5 4 1 FM Approved

PC04A *United Arab

Emirates

500 1895 95-170 655-1170 3550 5 4 1 FM Approved


500 1895 125-145 860-1000 3525 4 3 1 FM Approved


500 1895 95-120 655-825 3000 5 4 1 FM Approved


500 1895 48-80 330-550 2950 5 4 1 FM Approved


500 1895 173-277 1195-1910 2100 6 5 2 FM Approved


500 1895 50-84 345-580 3000 5 4 1 FM Approved

PD05A *

United

ArabEmirates

500 1895 121-190 835-1310 1760 6 5 2 FM Approved


500 1895 95-130 655-895 3525 4 3 1 FM Approved

PC05K *United ArabEmirates

500 1895 50-80 345-550 1760 6 5 1 FM Approved

TD10EUnited ArabEmirates

500 1895 66-99 455-685 2350 5 4 1 FM Approved


500 1895 67-113 460-780 2600 6 5 1 FM Approved


500 1895 68-124 470-855 2600 5 4 1 FM Approved


7/21/2019 FM guide


TE10D †United ArabEmirates

500 1895 72-137 495-945 2200 5 4 1 FM Approved


500 1895 80-108 550-745 3550 6 4 1 FM Approved

TE10D †

United

ArabEmirates

500 1895 81-150 560-1035 2300 5 4 1 FM Approved


500 1895 87-162 600-1115 2400 5 4 1 FM Approved


500 1895 96-176 660-1215 2500 5 4 1 FM Approved


500 1895 104-193 715-1330 2600 5 4 1 FM Approved


500 1895 121-229 835-1580 2800 5 4 1 FM Approved


500 1895 131-247 905-1705 2900 5 4 1 FM Approved


500 1895 135-255 930-1760 2950 5 4 1 FM Approved


500 1895 141-264 970-1820 3000 5 4 1 FM Approved

TE10A †United ArabEmirates

500 1895 144-219 995-1510 2950 5 4 1 FM Approved


500 1895 65-122 450-840 2100 5 4 1 FM Approved


500 1895 86-158 595-1090 2950 5 4 1 FM Approved

TX12D †United Arab

Emirates

500 1895 256-330 1765-2275 2950 6 5 2 FM Approved

TE12E †United ArabEmirates

500 1895 80-143 550-985 2200 6 5 1 FM Approved


500 1895 87-158 600-1090 2300 6 5 1 FM Approved


500 1895 97-171 670-1180 2400 6 5 1 FM Approved


500 1895 104-187 715-1290 2500 6 5 1 FM Approved


500 1895 72-131 495-905 2100 6 5 1 FM Approved

TY12D †

United

ArabEmirates

500 1895 145-191 1000-1317 1760 6 5 2 FM Approved

TY12D †United ArabEmirates

500 1895 173-223 1193-1538 1900 6 5 2 FM Approved


500 1895 214-276 1475-1903 2100 6 5 2 FM Approved


500 1895 260-334 1793-2303 2300 6 5 2 FM Approved


500 1895 273-350 1882-2413 2350 6 5 2 FM Approved

TX15EUnited ArabEmirates

500 1895 277-370 1850-2480 2950 8 6 2 FM Approved


7/21/2019 FM guide


TX15FUnited ArabEmirates

500 1895 283-378 1950-2610 2950 8 6 2 FM Approved

TY15EUnited ArabEmirates

500 1895 300-375 2070-2590 2350 8 6 2 FM Approved

TY15E

United

ArabEmirates

500 1895 288-360 1985-2480 2300 8 6 2 FM Approved


500 1895 240-298 1655-2055 2100 8 6 2 FM Approved


500 1895 195-242 1345-1670 1900 8 6 2 FM Approved


500 1895 171-210 1080-1450 1760 8 6 2 FM Approved


750 2840 199-240 1370-1655 2800 6 4 2 FM Approved


750 2840 227-272 1565-1875 2950 6 4 2 FM Approved


750 2840 234-286 1615-1970 3000 6 4 2 FM Approved


750 2840 295-352 2035-2430 3300 6 4 2 FM Approved


750 2840 235-417 1620-2875 3550 6 4 2 FM Approved

PD05L *United ArabEmirates

750 2840 183-311 1260-2145 1775 6 5 3 FM Approved

PC05H *United ArabEmirates

750 2840 173-180 1195-1240 2400 6 5 1 FM Approved

PC05H *United Arab

Emirates

750 2840 164-173 1130-1195 2350 6 5 1 FM Approved

PC05G *United ArabEmirates

750 2840 184-268 1270-1850 3550 6 5 1 FM Approved


750 2840 156-234 1075-1615 3300 6 5 1 FM Approved


750 2840 165-265 1140-1825 2100 6 5 2 FM Approved


750 2840 147-251 1015-1730 3550 5 4 1 FM Approved


750 2840 141-186 970-1280 3000 6 5 1 FM Approved

PC05H *

United

ArabEmirates

750 2840 130-138 895-950 2100 6 5 1 FM Approved


750 2840 101-180 695-1240 1770 6 5 2 FM Approved


750 2840 136-180 940-1240 2950 6 5 1 FM Approved


750 2840 125-207 860-1425 3300 8 6 1 FM Approved


750 2840 95-164 655-1130 2950 5 4 1 FM Approved


750 2840 100-170 690-1170 3000 5 4 1 FM Approved


7/21/2019 FM guide



750 2840 83-93 570-640 2800 5 4 1 FM Approved


750 2840 86-110 595-760 3000 5 4 1 FM Approved

PC04A *

United

ArabEmirates

750 2840 82-139 565-960 3300 5 4 1 FM Approved


750 2840 84-164 580-1130 3550 5 4 1 FM Approved


750 2840 85-113 585-780 3550 6 5 1 FM Approved


750 2840 80-159 550-1095 3500 5 4 1 FM Approved


750 2840 83-107 570-740 2950 5 4 1 FM Approved


750 2840 124-227 855-1565 2800 6 5 1 FM Approved


750 2840 105-193 725-1330 2600 6 5 1 FM Approved


750 2840 97-178 670-1225 2500 6 5 1 FM Approved


750 2840 88-162 605-1115 2400 6 5 1 FM Approved


750 2840 78-148 540-1020 2300 6 5 1 FM Approved


750 2840 70-134 485-925 2200 6 5 1 FM Approved

TE12E †United Arab

Emirates

750 2840 90-121 620-835 2100 6 5 1 FM Approved


750 2840 131-252 905-1735 3000 5 4 1 FM Approved


750 2840 124-243 855-1675 2950 5 4 1 FM Approved


750 2840 121-233 835-1605 2900 5 4 1 FM Approved


750 2840 112-216 770-1490 2800 5 4 1 FM Approved


750 2840 82-108 565-745 2100 5 4 1 FM Approved

PC05A *

United

ArabEmirates

750 2840 55-78 380-540 3000 6 5 1 FM Approved


750 2840 60-105 415-725 3565 6 5 1 FM Approved

PC06C *United ArabEmirates

500 1895 50-70 345-485 1760 8 6 1 FM Approved


500 1895 97-176 670-1215 3100 5 4 1 FM Approved


500 1895 40-66 255-455 1460 6 5 1 FM Approved

TC12G †United ArabEmirates

500 1890 138-193 950-1330 3550 6 5 1 FM Approved


7/21/2019 FM guide


TC12F †United ArabEmirates

500 1890 118-208 815-1435 3550 6 5 1 FM Approved


750 2840 59-104 405-715 2600 6 5 1 FM Approved

TC12G †

United

ArabEmirates

750 2840 130-185 895-1275 3550 6 5 1 FM Approved


500 1890 112-148 770-1020 3550 6 5 1 FM Approved


500 1890 102-139 705-960 3550 6 4 1 FM Approved


500 1890 81-133 560-915 3550 4 3 1 FM Approved

PC04D *United ArabEmirates

500 1895 40-50 270-345 1760 5 4 1 FM Approved


500 1895 43-49 295-340 1760 6 5 1 FM Approved

TE10DUnited ArabEmirates

500 1895 44-90 305-620 1760 5 4 1 FM Approved


500 1895 45-60 310-415 1760 5 4 1 FM Approved


500 1895 48-72 330-495 2100 6 5 1 FM Approved


500 1890 129-200 890-1380 3550 5 4 1 FM Approved


750 2840 111-199 765-1370 3550 6 5 1 FM Approved

PC05A *United Arab

Emirates

750 2840 60-111 415-765 3550 6 5 1 FM Approved

TD12FUnited ArabEmirates

750 2840 62-103 425-710 2350 6 5 1 FM Approved


750 2840 62-122 425-840 2200 5 4 1 FM Approved

BS08EUnited ArabEmirates

3000 11,355 179 1234 1490 10 8 1 FM Approved


3000 11,355 85-188 585-1195 1780 12 10 1 FM Approved


3000 11,355 75-123 515-850 1775 12 10 1 FM Approved

BS08B †

United

ArabEmirates

2500 9465 132-208 910-1435 1750 10 8 1 FM Approved

BS08B †United ArabEmirates

2500 9465 100-141 690-970 1475 10 8 1 FM Approved


2500 9465 105-144 725-995 2800 10 8 1 FM Approved

TD20D †United ArabEmirates

2500 9465 95-164 655-1130 2800 10 8 1 FM Approved

BS08A †United ArabEmirates

2500 9465 85-161 585-1110 1475 10 8 1 FM Approved

TF20DUnited ArabEmirates

2500 9465 87-146 600-1005 1760 10 8 1 FM Approved


7/21/2019 FM guide


BQ08E†**

United ArabEmirates

2500 9465 103-155 710-1070 1900-2300 10 8 1 FM Approved

BS08C †United ArabEmirates

2500 9465 142-167 980-1150 1475 10 8 1 FM Approved

TD20E †

United

ArabEmirates

2500 9465 119-163 820-1125 2950 10 8 1 FM Approved


2500 9465 85-127 585-875 1470 12 10 1 FM Approved


2500 9465 102-188 705-1295 2960 10 8 1 FM Approved


2500 9465 104-172 715-1185 1780 10 8 1 FM Approved


2500 9465 154-202 1060-1395 2100 10 8 1 FM Approved


2500 9465 105-155 725-1070 2100 10 8 1 FM Approved

PC08F *United ArabEmirates

2500 9465 80-140 550-965 1780 10 8 1 FM Approved


2500 9465 80-125 550-860 1780 10 8 1 FM Approved


2500 9465 115-150 795-1035 2100 10 8 1 FM Approved

TD25AUnited ArabEmirates

2500 9465 52-68 360-470 1760 10 10 1 FM Approved


2500 9465 52-98 360-675 1760 10 8 1 FM Approved

PC08F †United Arab

Emirates

2500 9465 65-90 450-620 1460 10 8 1 FM Approved

TE25AUnited ArabEmirates

2500 9465 73-114 505-785 1760 12 10 1 FM Approved

TF20EUnited ArabEmirates

2500 9465 75-134 515-925 1760 10 8 1 FM Approved

TF20FUnited ArabEmirates

2500 9465 76-123 525-850 1760 10 8 1 FM Approved


2500 9465 83-146 570-1005 2100 12 10 1 FM Approved


2500 9465 84-117 580-805 2100 10 8 1 FM Approved

TE20D

United

ArabEmirates

2500 9465 109-153 750-1055 2350 10 8 1 FM Approved

BS08EUnited ArabEmirates

2500 9465 183 1262 1490 10 8 1 FM Approved

BT10DUnited ArabEmirates

2500 9465 195-265 1345-1825 1480 12 10 1 FM Approved


1500 5680 110-179 760-1235 2800 10 8 1 FM Approved


1500 5680 95-172 655-1185 2950 8 6 1 FM Approved


1500 5680 105-190 725-1310 2950 10 8 1 FM Approved


7/21/2019 FM guide


BQ08E†**

United ArabEmirates

1500 5680 111-166 765-1145 1900-2300 10 8 1 FM Approved


1500 5680 97-160 670-1105 3550 8 6 1 FM Approved

PC08J *

United

ArabEmirates

1500 5680 73-105 505-710 1470 10 8 1 FM Approved

TF15E †United ArabEmirates

1500 5680 115-162 795-1115 1900 8 6 1 FM Approved

TD12F †United ArabEmirates

750 2840 141-208 970-1435 3550 6 5 1 FM Approved


750 2840 70-100 485-690 3565 6 5 1 FM Approved


750 2840 50-94 345-650 1760 6 5 1 FM Approved


750 2840 54-75 370-515 2950 6 5 1 FM Approved


750 2840 54-82 370-565 2350 6 5 1 FM Approved


750 2840 94-179 650-1235 2600 5 4 1 FM Approved


750 2840 136-245 940-1690 2900 6 5 1 FM Approved

BS06A†**

United ArabEmirates

750 2840 95-135 655-930 2450-3000 8 6 1 FM Approved


750 2840 141-255 970-1760 2950 6 5 1 FM Approved

BS06A †United Arab

Emirates

750 2840 100-150 690-1035 2970 8 6 1 FM Approved


750 2840 146-264 1005-1820 3000 6 5 1 FM Approved

TE10A †United ArabEmirates

750 2840 136-213 940-1470 2950 5 4 1 FM Approved


750 2840 95-165 655-1140 2950 6 5 1 FM Approved


750 2840 111-142 765-980 2950 6 5 1 FM Approved


750 2840 74-134 510-925 2950 6 5 1 FM Approved

TY12D †

United

ArabEmirates

750 2840 163-200 1124-1379 1900 6 5 2 FM Approved


750 2840 190-250 1310-1724 2100 6 5 2 FM Approved

TX12D †United ArabEmirates

750 2840 230-300 1585-2070 2950 6 5 2 FM Approved


750 2840 240-312 1655-2151 2300 6 5 2 FM Approved


750 2840 250-328 1724-2262 2350 6 5 2 FM Approved


750 2840 268-360 1850-2480 2950 8 6 2 FM Approved


7/21/2019 FM guide



750 2840 276-370 1905-2550 2950 8 6 2 FM Approved


750 2840 296-370 2040-2550 2350 8 6 2 FM Approved

TY15E

United

ArabEmirates

750 2840 284-353 1960-2435 2300 8 6 2 FM Approved


750 2840 235-294 1620-2030 2100 8 6 2 FM Approved


750 2840 190-237 1310-1635 1900 8 6 2 FM Approved


750 2840 166-205 1145-1415 1760 8 6 2 FM Approved


1000 3785 43-53 295-365 1760 8 6 1 FM Approved


750 2840 70-96 485-660 3300 6 5 1 FM Approved


750 2840 65-123 450-850 2800 6 5 1 FM Approved


750 2840 69-95 475-655 3550 6 4 1 FM Approved


750 2840 106-144 730-990 3550 6 5 1 FM Approved


750 2840 69-137 475-945 2300 5 4 1 FM Approved


750 2840 95-129 655-890 3550 6 4 1 FM Approved

TE10D †United Arab

Emirates

750 2840 77-149 530-1025 2400 5 4 1 FM Approved


750 2840 40-56 275-385 1760 5 4 1 FM Approved


750 2840 44-54 305-370 1760 6 5 1 FM Approved


750 2840 85-164 585-1130 2500 5 4 1 FM Approved


750 2840 47-71 325-490 1760 8 6 1 FM Approved


750 2840 47-67 325-460 2950 6 5 1 FM Approved

PC05B *

United

ArabEmirates

750 2840 48-70 330-485 3000 6 5 1 FM Approved


750 2840 49-81 340-560 2100 6 5 1 FM Approved


750 2840 60-106 415-730 3500 6 5 1 FM Approved


2000 7570 104-174 715-1200 2800 10 8 1 FM Approved


2000 7570 95-179 655-1235 2950 10 8 1 FM Approved

TD20DUnited ArabEmirates

2000 7570 73-138 505-950 2600 10 8 1 FM Approved


7/21/2019 FM guide



2000 7570 77-133 530-915 1760 10 8 1 FM Approved

TF20EUnited ArabEmirates

2000 7570 80-142 550-980 1760 10 8 1 FM Approved

TD20E †

United

ArabEmirates

2000 7570 84-159 580-1095 2800 10 8 1 FM Approved


2000 7570 147-196 1015-1350 3550 10 8 1 FM Approved


2000 7570 63-74 435-510 1760 10 8 1 FM Approved


2000 7570 63-101 435-695 2350 10 8 1 FM Approved


2000 7570 45-89 310-615 1780 10 8 1 FM Approved


2000 7570 54-94 370-650 1460 10 8 1 FM Approved


2000 7570 69-130 475-895 2100 10 8 1 FM Approved


2000 7570 69-130 475-895 2600 10 8 1 FM Approved


2000 7570 87-140 600-965 2100 8 6 1 FM Approved


2000 7570 97-197 670-1360 2960 10 8 1 FM Approved


2000 7570 110-167 760-1150 2100 10 8 1 FM Approved

PC08K *United Arab

Emirates

2000 7570 72-119 495-820 1470 10 8 1 FM Approved

PC08J *United ArabEmirates

2000 7570 150-212 1035-1460 2100 10 8 1 FM Approved


2000 7570 90-118 620-815 1780 10 8 1 FM Approved


2000 7570 55-85 380-585 1470 10 8 1 FM Approved

TD25AUnited ArabEmirates

2000 7570 56-72 385-495 1760 10 10 1 FM Approved


2000 7570 56-108 385-745 2350 10 8 1 FM Approved

TD20D

United

ArabEmirates

2000 7570 58-82 400-565 2100 10 8 1 FM Approved


2000 7570 125-162 860-1115 2950 8 6 1 FM Approved


2000 7570 91-164 625-1130 1475 10 8 1 FM Approved


2000 7570 94-150 650-1035 1475 10 8 1 FM Approved

TF20DUnited ArabEmirates

2000 7570 94-150 640-1035 1760 10 8 1 FM Approved


2000 7570 90-125 620-860 2100 10 8 1 FM Approved


7/21/2019 FM guide



2000 7570 142-214 980-1475 1750 10 8 1 FM Approved

BQ08E†**

United ArabEmirates

2000 7570 108-160 745-1105 1900-2300 10 8 1 FM Approved

PC08J *

United

ArabEmirates

2000 7570 103-156 710-1015 1780 10 8 1 FM Approved


2000 7570 110-175 760-1205 1780 10 8 1 FM Approved


2000 7570 115-160 795-1105 2350 10 8 1 FM Approved


1500 5680 116-199 800-1370 2100 8 6 1 FM Approved


1500 5680 108-136 745-940 1760 8 6 1 FM Approved


1500 5680 108-141 745-970 3550 8 6 1 FM Approved


1500 5680 40-77 275-530 1760 10 8 1 FM Approved


1500 5680 41-55 285-380 1760 10 8 1 FM Approved


1500 5680 45-87 310-600 2100 10 8 1 FM Approved


1500 5680 128-220 885-1515 2200 8 6 1 FM Approved


1500 5680 85-122 585-840 1780 8 6 1 FM Approved

PC60L *United Arab

Emirates

1500 5680 160-202 1105-1390 2100 8 6 1 FM Approved


1500 5680 143-241 985-1660 2300 8 6 1 FM Approved


1500 5680 151-175 1040-1205 1770 10 8 2 FM Approved

PC60L *United ArabEmirates

1500 5680 105-140 725-965 1770 8 6 1 FM Approved


1500 5680 151-243 1040-1675 2350 8 6 1 FM Approved


1500 5680 147-268 1015-1850 3550 8 6 1 FM Approved

TD20E †

United

ArabEmirates

1500 5680 154-202 1060-1390 3550 10 8 1 FM Approved


1500 5680 88-157 605-1080 2950 8 6 1 FM Approved


1500 5680 139-155 960-1070 3550 8 6 1 FM Approved


1500 5680 121-220 835-1515 3300 8 6 1 FM Approved


1500 5680 120-160 825-1105 2800 8 6 1 FM Approved


1500 5680 112-180 770-1240 3000 8 6 1 FM Approved


7/21/2019 FM guide



1500 5680 110-160 760-1105 1780 10 8 1 FM Approved


1500 5680 108-177 745-1220 2950 8 6 1 FM Approved

TD15F †

United

ArabEmirates

1500 5680 133-187 915-1290 3550 8 6 1 FM Approved


1500 5680 40-63 275-435 1470 10 8 1 FM Approved


1500 5680 74-144 535-990 2800 8 6 1 FM Approved


1500 5680 81-140 560-965 1760 10 8 1 FM Approved


1500 5680 64-116 441-800 2600 8 6 1 FM Approved


1500 5680 67-76 460-525 1760 8 6 1 FM Approved


1500 5680 72-112 495-770 2350 10 8 1 FM Approved


1500 5680 100-136 690-940 3300 8 6 1 FM Approved


1500 5680 45-86 310-595 1760 8 6 1 FM Approved


1500 5680 47-60 325-415 1760 10 8 1 FM Approved


1500 5680 57-94 385-650 2350 8 6 1 FM Approved

TD15F †United Arab

Emirates

1500 5680 88 605 2300 8 6 1 FM Approved


1500 5680 91-169 630-1165 2800 10 8 1 FM Approved

TE15EUnited ArabEmirates

1000 3785 44-79 305-545 1760 8 6 1 FM Approved


1000 3785 159-213 1095-1470 2800 6 5 1 FM Approved


1000 3785 132-181 910-1250 2600 6 5 1 FM Approved


1000 3785 97-171 670-1180 2950 8 6 1 FM Approved

TF15E †

United

ArabEmirates

1000 3785 160-251 1100-1730 2350 8 6 1 FM Approved


1000 3785 152-251 1050-1730 2300 8 6 1 FM Approved


1000 3785 139-228 960-1570 2200 8 6 1 FM Approved


1000 3785 126-208 870-1435 2100 8 6 1 FM Approved


1000 3785 101-171 695-1180 1900 8 6 1 FM Approved


1000 3785 85-145 585-1000 1760 8 6 1 FM Approved


7/21/2019 FM guide



1000 3785 123-232 850-1600 2900 6 5 1 FM Approved


1000 3785 128-240 885-1655 2950 6 5 1 FM Approved

TE12E †

United

ArabEmirates

1000 3785 134-250 925-1725 3000 6 5 1 FM Approved


1000 3785 90-157 620-1080 2800 8 6 1 FM Approved


1000 3785 74-128 510-883 2600 8 6 1 FM Approved


1000 3785 102 705 2300 8 6 1 FM Approved


1000 3785 100-131 690-905 2950 6 5 1 FM Approved


1000 3785 89-159 615-1095 2950 6 5 1 FM Approved


1000 3785 254-346 1750-2385 2950 8 6 2 FM Approved


1000 3785 268-361 1850-2490 2950 8 6 2 FM Approved


1000 3785 291-361 2010-2490 2350 8 6 2 FM Approved


1000 3785 278-345 1915-2380 2300 8 6 2 FM Approved


1000 3785 227-285 1565-1965 2100 8 6 2 FM Approved

TY15EUnited Arab

Emirates

1000 3785 181-230 1250-1585 1900 8 6 2 FM Approved


1000 3785 155-196 1070-1350 1760 8 6 2 FM Approved


1000 3785 100-150 690-1035 2970 8 6 1 FM Approved

BS06A†**

United ArabEmirates

1000 3785 93-130 640-895 2450-3000 8 6 1 FM Approved


1000 3785 75-135 515-930 3000 6 5 1 FM Approved


1000 3785 70-130 485-895 2950 6 5 1 FM Approved

TD12F

United

ArabEmirates

1000 3785 72-121 495-835 2600 6 5 1 FM Approved


1000 3785 134-199 925-1370 3550 6 5 1 FM Approved


1000 3785 74-113 510-780 1780 8 6 1 FM Approved


1000 3785 70-108 485-745 2800 8 6 1 FM Approved


1000 3785 60-106 415-730 3550 6 5 1 FM Approved


1000 3785 55-86 380-595 1460 8 6 1 FM Approved


7/21/2019 FM guide



1000 3785 57-95 395-655 2350 6 5 1 FM Approved


1000 3785 60-73 415-505 2100 6 5 1 FM Approved

TB12D †

United

ArabEmirates

1000 3785 99-137 680-945 3550 6 5 1 FM Approved


1000 3785 165-176 1140-1215 2400 6 5 1 FM Approved


1000 3785 145-165 1000-1140 3550 8 6 1 FM Approved


1000 3785 155-167 1070-1150 2350 6 5 1 FM Approved


1000 3785 128-175 880-1205 2950 6 5 1 FM Approved


1000 3785 115-210 795-1450 1770 8 6 2 FM Approved


1000 3785 77-114 530-785 2950 8 6 1 FM Approved


1000 3785 79-107 545-740 3550 6 5 1 FM Approved


1000 3785 82-121 565-835 3000 8 6 1 FM Approved


1000 3785 101-147 695-1015 3300 8 6 1 FM Approved


1000 3785 103-169 710-1165 3550 8 6 1 FM Approved

TB12FUnited Arab

Emirates

1000 3785 104-144 715-995 3550 6 5 1 FM Approved


1000 3785 115-153 795-1055 3550 8 6 1 FM Approved


1000 3785 100-195 690-1340 3550 6 5 1 FM Approved


1000 3785 85-100 585-690 3565 6 5 1 FM Approved


1000 3785 95-165 655-1140 3300 6 5 1 FM Approved


1000 3785 97-190 670-1310 3500 6 5 1 FM Approved

PC05G *

United

ArabEmirates

1000 3785 170-260 580-1140 3500 6 5 1 FM Approved


1000 3785 145-222 1000-1530 3300 6 5 1 FM Approved


1000 3785 132-181 910-1250 3000 6 5 1 FM Approved


1000 3785 172-262 1185-1805 3550 6 5 1 FM Approved


1000 3785 171-205 1180-1415 2100 8 6 1 FM Approved


1000 3785 119-145 820-1000 1770 8 6 1 FM Approved


7/21/2019 FM guide



1000 3785 44-85 305-585 1760 8 6 1 FM Approved


1000 3785 54-87 370-600 1760 8 6 1 FM Approved

PC05B *

United

ArabEmirates

1000 3785 65-95 450-655 3565 6 5 1 FM Approved


1000 3785 119-175 820-1205 3550 6 5 1 FM Approved


1000 3785 84-165 580-1140 3300 6 5 1 FM Approved


1000 3785 89-105 615-725 3550 6 5 1 FM Approved


1250 4730 97-164 670-1130 3550 8 6 1 FM Approved


1250 4730 65-103 450-710 2800 8 6 1 FM Approved


1250 4730 90-169 620-1165 2800 8 6 1 FM Approved


1250 4730 97-142 670-980 3300 8 6 1 FM Approved


1250 4730 40-82 275-565 1760 8 6 1 FM Approved


1250 4730 50-81 345-560 1760 8 6 1 FM Approved


1250 4730 165-205 1140-1415 2100 8 6 1 FM Approved

PC06C *United Arab

Emirates

1250 4730 152-273 1050-1880 3550 8 6 1 FM Approved


1250 4730 142-160 980-1105 3550 8 6 1 FM Approved


1250 4730 126-229 870-1580 3300 8 6 1 FM Approved


1250 4730 110-145 760-1000 1770 8 6 1 FM Approved


1250 4730 111-150 765-1035 3550 8 6 1 FM Approved


1250 4730 104-186 715-1280 3000 8 6 1 FM Approved

PC06C *

United

ArabEmirates

1250 4730 100-182 690-1255 2950 8 6 1 FM Approved


1250 4730 60-127 415-875 1780 8 6 1 FM Approved


1250 4730 62-100 425-690 2350 8 6 1 FM Approved


1250 4730 74-110 510-760 2950 8 6 1 FM Approved


1250 4730 75-116 515-800 3000 8 6 1 FM Approved


1250 4730 55-82 380-565 1460 8 6 1 FM Approved


7/21/2019 FM guide


TE15EUnited ArabEmirates

1250 4730 59-74 405-510 1760 8 6 1 FM Approved


1250 4730 134-225 925-1550 2200 8 6 1 FM Approved

TD15F †

United

ArabEmirates

1250 4730 137-191 945-1315 3550 8 6 1 FM Approved


1250 4730 125-191 860-1315 3550 6 5 1 FM Approved

BS06A†**

United ArabEmirates

1250 4730 87-130 600-895 2450-3000 9 6 1 FM Approved


1250 4730 100-150 690-1035 2970 8 6 1 FM Approved


1250 4730 82-148 565-1020 2950 6 5 1 FM Approved


1250 4730 108-196 745-1350 2950 10 8 1 FM Approved


1250 4730 95 655 2300 8 6 1 FM Approved


1250 4730 70-123 483-848 2600 8 6 1 FM Approved


1250 4730 96-174 660-1200 2800 10 8 1 FM Approved


1250 4730 84-150 580-1035 2800 8 6 1 FM Approved


1250 4730 81-142 560-980 1760 8 6 1 FM Approved

TF15E †United Arab

Emirates

1250 4730 148-246 1020-1695 2300 8 6 1 FM Approved


1250 4730 93-164 640-1130 2950 8 6 1 FM Approved


1250 4730 97-166 670-1145 1900 8 6 1 FM Approved

TB12FUnited ArabEmirates

1250 4730 98-132 675-910 3550 6 5 1 FM Approved


1250 4730 122-203 840-1400 2100 8 6 1 FM Approved


1250 4730 155-246 1070-1695 2350 8 6 1 FM Approved

TX15E

United

ArabEmirates

1250 4730 275-329 1895-2270 2950 8 6 2 FM Approved


1250 4730 246-348 1695-2400 2950 8 6 2 FM Approved


1250 4730 278-347 1920-2390 2350 8 6 2 FM Approved


1250 4730 265-331 1830-2280 2300 8 6 2 FM Approved


1250 4730 214-274 1475-1890 2100 8 6 2 FM Approved


1250 4730 170-215 1170-1480 1900 8 6 2 FM Approved


7/21/2019 FM guide


* When requested, SPP can furnish pumps designed for applications where the suction pressures exceed 75 psi (515 kPa). These pumps are designated by theaddition of the letter ‘‘H’’ after the type designation.** These pumps are available for operation at any speed within the range shown. The intended operating speed should be specified when the pump is ordered.† These designations have (FM) following the designation number.

Standart Pompa Ve Mak. San. Tic. A.S.Dudullu Organize San. Bol., 2. Cadde, No. 9, Esenkent - Ümraniye, Istanbul, Turkey





psi


kPa

RatedSpeed,r/min

SuctionInlet,

dia., in.



Type

SDS100-250

Turkey 750 2840 86-172 595-1185 3000 6 4 1 FM Approved

SDS100-250


SDS125-315


SDS125-315


FM guide

Documents

Transcript of FM guide