FLORIDA SHERIFFS ASSOCIATION & FLORIDA ASSOCIATION OF … · 2018-12-21 · florida sheriffs...

FLORIDA SHERIFFS ASSOCIATION& FLORIDA ASSOCIATION OF COUNTIES

SPECIFICATION #1 - OFF-ROAD ALL TERRAIN VEHICLES - 4 WHEEL DRIVE2019 Honda Four Trax Foreman 500 (TRX500FA5K)2019 Polaris Sportsman 570 EFI (A19SEA57B1)2019 Yamaha Kodiac 450 (YFM45KDXK)

THE FOLLOWING ITEMS WILL BE FACTORY INSTALLED ON THE BASE VEHICLE/EQUIPMENT TO MEETTHE MODEL NUMBER AND BUILD CODES OF THE VEHICLE LISTED. PLEASE REFER TO THEEMERGENCY VEHICLE LIGHTING AND SIRENS SECTION WITHIN THIS CONTRACT FOR DESCRIPTIONS,SPECIFICATIONS AND AWARDED VENDOR PRICING.

FSA BASE VEHICLE REQUIREMENTS1.

2 – programmed keys and fobs, if availablea.

ENGINE:2.

Manufacture's minimum 1 cylinder 4 stroke fuel injected gas engine.a.Liquid cooledb.Key/electric startc.20 HP minimumd.

TRANSMISSION:3.

Manufacture's standard automatic transmissiona.

BATTERY:4.

300 CCAa.

BRAKES:5.

Front disc / rear druma.

SAFETY ITEMS:6.

Safety shut off switcha.Hi/lo headlightsb.

WHEELS/TIRES:7.

Standard all terrain tiresa.

CHASSIS, FRAME, CAB:8.

Standard headlightsa.Standard taillightsb.Power plugc.Standard front and rear racksd.Standard floorboardse.Minimum tow capacity 800 lbsf.


SPECIFICATION #2 - OFF-ROAD UTILITY VEHICLES - 4 WHEEL DRIVE2019 Bobcat 3400 UTV2019 Club Car Carry All 1500 G2019 Cub Cadet 5502019 Honda Pioneer 700 (SXS700M2K) 2019 John Deere Gator HPX615E2019 Kawasaki Mule 4010 4X42019 Kubota Diesel (RTVX900)2019 Mahindra Retriever UTV 750B2019 Polaris Ranger 570 EFI (R19RMA57B1) 2019 Yamaha Viking (YXM70VDXK)




ENGINE2.

Manufacturer's gas or diesel engine, air cooled, overhead valve, keyed electronic ignition, 20 HP minimum.a.

TRANSMISSION3.

Manufacturer's standard automatic transmissiona.

BATTERY4.

300 ccaa.

CHASSIS5.

Standard headlightsa.Standard taillightsb.Power plugc.Front brakes: hydraulic discsd.Rear brakes: hydraulic drume.Steering rack and pinionf.Standard front bumperg.

TIRES AND WHEELS6.

Front and rear all terrain tires, must match drive traina.


SPECIFICATION #3 - LOW SPEED VEHICLE2019 CitiCar 4PR2019 Columbia Summit Utility Truck (SU5-LN)




CLASSIFICATION2.

These vehicles are primarily used to transport people and limited cargo in the State of Florida on typical federal, state, county andcity highways and roads that are posted for 35 mph or less and shall be designed to operate under typical environmental conditions.

a.

Vehicles must conform to Federal Motor Vehicle Safety Standards, State of Florida Vehicle Safety Laws, regulations,specifications, standards and requirements in effect as of the date of manufacture.

b.

ENGINE3.

5.5HP 4 kw Electric Motora.48 Volt Lead Acid Batteries (8 Batteries x 6v)b.Trojan T105 Batteriesc.Curtis Sepex 1268 Controllerd.110V Eagle On Board Chargere.50 Miles per Chargef.Max Forward Speed 25mphg.Digital Speedometer and Dashboardh.

DIMENSIONS (APPROXIMATE)4.

Length: 96"a.Height: 76"b.Width: 48"c.Wheel Base 66.9"d.Ground Clearance 5"e.

BODY5.

Plastic body and fiberglass roofa.DOT Windshield with Wiperb.Wood Grain Steering Wheel, Dashboard and Back Restsc.

COMFORT ITEMS6.

4 Person Seating with Flip Rear Seat for Cargoa.Cup Holdersb.

CHASSIS/STEERING/SUSPENSION7.

Front and Rear Plate Spring + Cylinder Hydraulic Shock Absorber Suspensiona.10 Foot Turning Radiusb.Steel Frame Type Chassisc.500lbs GVW Capacityd.Front Independent Suspensione.Rack & Pinion Steeringf.

TIRES AND WHEELS:8.

205/50-10 Tiresa.10" Aluminum Rimsb.

BRAKES9.

4 Wheel Hydraulica.Hand Brakeb.

SAFETY ITEMS10.

100% Electric with Zero Emmissions a.12V Headlights and Indicators b.Voltmeter c.Turn Signals d.Side and Rear View Mirrors e.Reverse Alarm f.Non-Slip Flooring g.Neutral Switch When Vehicle is Standing Still h.Horn i.

PERFORMANCE:11.

45 mile range a.19 MPH minimum b.


SPECIFICATION #4 - ELECTRIC UTILITY VEHICLE2019 Carryall 500 (104030201)2019 Polaris Ranger EV (R19RMAE4G8)2019 Xtreme Green Transport Pro



2 – programmed keys and fobs, if availablea.Full-size spare tire, if availableb.


Length: 115"a.Height: 51"b.Width: 56"c.Wheel Base 79"d.Curb Weight 1500 lbs.e.GVW 2900 lbs.f.

POWER:3.

7 HP Electric Motora.8-6 Volt Heavy Duty Batteriesb.48 Voltc.

TRANSMISSION/AXLE:4.

Enclosed internally lubricated differential/transaxlea.2 Wheel Driveb.

CHASSIS/STEERING/SUSPENSION5.

1250 lbs. towing capacitya.2900 lbs. GVWb.Frame Type Chassisc.Suspension matched for GVW of vehicled.

TIRES AND WHEELS:6.

Off/on road type tiresa.Wheels rated for GVW of vehicleb.Tires to be traction type rated for GVW of vehiclec.

PERFORMANCE:7.

45 mile rangea.19 MPH minimumb.

BRAKES:8.

Manual parking brakea.Disc or drum typeb.2 or 4 wheel breaksc.

BODY:9.

Rear mounted hitch for towing 2"a.Pick-up type box with sides and tailgateb.2 passenger seatingc.


SPECIFICATION #5 - 1 TON CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Chevrolet Silverado 3500 HD (CC36003)2019 Ford F-350 (F3G)2019 GMC Sierra 3500 HD (TC36003)2019 Ram 3500 (DD3L63)



Air conditioninga.Standard full-size spare tire, if availableb.2 – keysc.

ENGINE:2.

Manufacturer's standard gas engine, alternator, battery and cooling package.a.

TRANSMISSION/AXLES:3.

Manufacturer's standard automatic transmission.a.Manufacturer's standard drive axle ratio for engine and transmission combination.b.

PERFORMANCE ITEMS:4.

Manufacturer's standard power steering.a.Manufacturer's standard gauges.b.

COMFORT ITEMS:5.

Manufacturer's standard tinted glass all around.a.Manufacturer's standard AM/FM stereo.b.Heavy duty rubber floor covering instead of carpet.c.Manufacturer's standard production seats. Purchaser will select color at time of order.d.

SAFETY ITEMS:6.

Dual mount outside mirrors to provide field of vision for vehicles to 96" wide.a.Interior dome lights with left and right door activated switches.b.Manufacturer's standard air bags.c.

BRAKES:7.

Four wheel anti-lock brake ABS system.a.

TIRES AND WHEELS:8.

Manufacturer's standard tires and wheels.a.


Manufacturer's standard bumper.a.Manufacturer's standard fuel tank.b.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.c.


SPECIFICATION #6 - 1 TON CAB & CHASSIS (DUAL REAR WHEEL) - 4X42019 Chevrolet Silverado 3500 HD (CK36003)2019 Ford F-350 (F3H)2019 GMC Sierra 3500 HD (TK36003)2019 Ram 3500 (DD8L63)



Air conditioninga.Standard full-size spare tire, if availableb.2 – keysc.Limited slip differentiald.

ENGINE:2.

Manufacturer's standard gas engine, alternator, battery and cooling package.a.


Manufacturer's standard automatic transmission.a.Manufacturer's standard drive axle ratio for engine and transmission combination.b.Manufacturer's standard transfer casec.



COMFORT ITEMS:5.

Manufacturer's standard tinted glass all around.a.Manufacturer's standard AM/FM stereo.b.Heavy duty rubber floor covering instead of carpet.c.Manufacturer's standard production seats. Purchaser will select color at time of order.d.

SAFETY ITEMS:6.

Dual mount outside mirrors to provide field of vision for vehicles to 96" wide.a.Interior dome lights with left and right door activated switches.b.Manufacturer's standard air bags.c.

BRAKES:7.


TIRES AND WHEELS:8.

Manufacturer's standard tires and wheels.a.


Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.a.Manufacturer's standard fuel tank.b.Manufacturer's standard bumper.c.


SPECIFICATION #7 - TILT CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Chevrolet 4500HD Diesel LCF (CT31003)2019 Isuzu FTR Chassis2019 Isuzu NF1542019 Kenworth K2702019 Mitsubishi FE1302019 Peterbilt 220




ENGINE:2.

Manufacturer's standard diesel enginea.Heavy duty alternatorb.Maintenance free heavy duty batteryc.Manufacturer's heavy duty engine coolingd.


Manufacturer's standard automatic transmission.a.Manufacturer's standard drive axle ratio for engine and transmission combination.b.



COMFORT ITEMS:5.

Manufacturer's standard tinted glass all around.a.Manufacturer's standard AM/FM stereo.b.Heavy duty rubber floor covering instead of carpet.c.Manufacturer's standard production seats. Purchaser will select color at time of order.d.Manufacturer Power Windows and Door Lockse.Manufacturer Keyless Entryf.

SAFETY ITEMS:6.

Dual mount outside mirrors to provide field of vision for vehicles to 96" wide.a.Interior dome lights with left and right door activated switches.b.Manufacturer's standard air bags, if available.c.Manufacturer's standard convex mirrors.d.

BRAKES:7.


TIRES AND WHEELS:8.

BSW steel belted radials, 215/85R16E minimum.a.16 x 6.0 steel - 6-hole disc wheels.b.Tire capacity: front - 2,400 lbs. (ea.); rear - 2,200 lbs. (ea.).c.


Minimum 12,000 lb. GVWR.a.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.b.Manufacturer's standard fuel tank.c.Manufacturer's standard bumper.d.Cab with 45-degree mechanical tilt with torsion assist.e.Tilt cab & chassis only.f.


SPECIFICATION #8 - 15,000 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Chevrolet Silverado 4500HD WT (CC56403 /C7R)2019 Ford F-450 (F4G)2019 International CV2019 Ram 4500 (DP4L63)




ENGINE:2.

Manufacturer's standard diesel engine.a.Maintenance free heavy duty batteryb.Manufacturer's heavy duty engine coolingc.Heavy duty alternatord.


Manufacturer's standard automatic transmissiona.Manufacturer's standard drive axle ratio for engine and transmission combination.b.


Manufacturer's standard power steering.a.Manufacturer's standard gauges.b.Heavy duty front and rear shocks.c.

COMFORT ITEMS:5.

Manufacturer's standard tinted glass all around.a.Manufacturer's standard AM/FM stereo.b.Heavy duty rubber floor covering instead of carpet.c.Vinyl seating with head rests to accommodate 3 passengers. Purchaser will select color at time of order.d.Factory Power Windows and Door Lockse.Keyless Entryf.

SAFETY ITEMS:6.

Dual mount outside mirrors must provide a field of vision for vehicles to 96" width, and for towing.a.Interior dome lights with left and right door activated switches.b.Air bags for driver and right front passenger, if available.c.Back Up Camera, if required by federal standardsd.

BRAKES:7.

Rear anti-lock brakes, minimum.a.

TIRES AND WHEELS:8.

BSW all season tread radial, 19.5" heavy duty truck tires.a.


Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.a.Manufacturer's standard front bumper, bright or painted.b.Fuel tank capacity, 25 gallons minimum.c.Cab to center of rear axle - 60" approximately.d.Minimum 15,000 lbs. GVWR.e.Cab & chassis only.f.


SPECIFICATION #9 - 15,000 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X42019 Chevrolet Silverado 4500HD WT (CK56403/C7R)2019 Ford F-450 (F4H)2019 International CV2019 Ram 4500 (DP9L63)



Air conditioninga.Standard full-size spare tire, if availableb.2 – keysc.Limited slip differential, if availabled.

ENGINE:2.

Manufacturer's standard diesel engine.a.Maintenance free heavy duty batteryb.Manufacturer's heavy duty engine cooling.c.Heavy duty alternatord.


Manufacturer's standard automatic transmissiona.Manufacturer's standard drive axle ratio for engine and transmission combination.b.Manufacturer's standard transfer casec.



COMFORT ITEMS:5.

Manufacturer's standard tinted glass all around.a.Manufacturer's standard AM/FM stereo.b.Heavy duty rubber floor covering instead of carpet.c.Vinyl seating with head rests to accommodate 3 passengers. Purchaser will select color at time of order.d.

SAFETY ITEMS:6.

Dual mount outside mirrors must provide a field of vision for vehicles to 96" width, and for towing.a.Interior dome lights with left and right door activated switches.b.Air bags for driver and right front passenger, if available.c.

BRAKES:7.


TIRES AND WHEELS:8.



Fuel tank capacity, 25 gallons minimum.a.Manufacturer's standard front bumper, bright or painted.b.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.c.Cab & chassis only.d.Minimum 15,000 lbs. GVWR.e.Cab to center of rear axle - 60" approximately.f.


SPECIFICATION #10 - 17,500 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Chevrolet Silverado 5500HD WT (CC56403/GZX)2019 Ford F-550 (F5G)2019 Freightliner M22019 International CV2019 Kenworth T1702019 Peterbilt 3252019 Ram 5500 (DP5L63)

THE ITEMS BELOW WILL BE FACTORY INSTALLED ON THE BASE VEHICLE/EQUIPMENT TO MEET THEMODEL NUMBER AND BUILD CODES OF THE VEHICLE LISTED. PLEASE REFER TO THE EMERGENCYVEHICLE LIGHTING AND SIRENS SECTION WITHIN THIS CONTRACT FOR DESCRIPTIONS,SPECIFICATIONS AND AWARDED VENDOR PRICING.



ENGINE:2.

Diesel engine, minimum 190 HPa.Maintenance free heavy duty batteryb.Manufacturer's heavy duty engine cooling.c.Heavy duty alternatord.


Manufacturer's standard automatic 4-speed transmission with overdrive and manufacturer's heavy duty cooling.a.Manufacturer's standard drive axle ratio for engine and transmission combination.b.



COMFORT ITEMS:5.


SAFETY ITEMS:6.


BRAKES:7.

Rear anti-lock brakes, minimum.a.Power brakes, front brakes disc type, rear brakes may be drum or disc.b.

TIRES AND WHEELS:8.



Cab to center of rear axle - 60" approximately.a.Minimum 17,501 lbs. GVWR.b.Cab & chassis only.c.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.d.Manufacturer's standard front bumper, bright or painted.e.Fuel tank capacity, 24 gallons minimum.f.


SPECIFICATION #11 - 17,500 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X42019 Chevrolet Silverado 5500HD WT (CK56403/GZX)2019 Ford F-550 (F5H)2019 Freightliner M22019 International CV2019 Ram 5500 (DP0L63)



Air conditioninga.Standard full-size spare tire, if availableb.2 – keysc.Limited slip differential, If availabled.

ENGINE:2.

Diesel engine, minimum 190 HPa.Maintenance free heavy duty batteryb.Manufacturer's heavy duty engine cooling.c.Heavy duty alternatord.


Manufacturer's standard automatic transmissiona.Manufacturer's standard drive axle ratio for engine and transmission combination.b.Manufacturer's standard transfer casec.



COMFORT ITEMS:5.


SAFETY ITEMS:6.


BRAKES:7.


TIRES AND WHEELS:8.



Cab to center of rear axle - 60" approximately.a.Minimum 17,501 lbs. GVWR.b.Cab & chassis only.c.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.d.Manufacturer's standard front bumper, bright or painted.e.Fuel tank capacity, 25 gallons minimum.f.


SPECIFICATION #12 - 25,500 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Hino 268A2019 Ford F-650 (F6D)2019 Freightliner M22019 International MV2019 Kenworth T2702019 Peterbilt 330

THE FOLLOWING ITEMS WILL BE FACTORY INSTALLED ON THE BASE VEHICLE/EQUIPMENT TO MEETTHE MODEL NUMBER AND BUILD CODES OF THE VEHICLE LISTED.


Air Conditioninga.Standard full-size spare tire, if availableb.2 - Keysc.

ENGINE:2.

Diesel engine, minimum 200 HPa.


All axles, synthetic lube.a.Manufacturers standard automatic transmission or approved equivalent (with PTO provision).b.17,500 lb. rear axlec.



COMFORT ITEMS:5.

Air conditioning, factory installed.a.Manufacturer's standard tinted glass all around.b.Manufacturer's standard AM/FM stereo.c.Heavy duty rubber floor covering instead of carpet.d.Manufacturer's standard production seats. Purchaser will select color at time of order.e.Keys: two (2) per vehicle, single key locking system, (each vehicle keyed differently).f.

SAFETY ITEMS:6.

Dual mount outside mirrors must provide a field of vision for vehicles to 102" width, and for towing.a.Convex mirrors mounted below standard mirrors.b.Interior dome lights with left and right door activated switches.c.

BRAKES:7.

Factory air brakesa.Anti-lock brake systemb.

TIRES AND WHEELS:8.

BSW 11R22.5 (14 PR) or approved equivalent, front and rear.a.Oil bath hubs, with synthetic lube.b.


Minimum 25,500 lbs. GVWR.a.Cab & chassis only.b.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.c.Manufacturer's standard front bumper, bright or painted.d.Factory front tow hooks.e.Fuel tank capacity, 45 gallons minimum.f.Cab to center of rear axle - 84" approximately.g.


SPECIFICATION #13 - 30,000 LB GVWR CAB & CHASSIS (DUAL REAR WHEEL) - 4X22019 Hino 3382019 Ford F-750 (F7D)2019 Freightliner M22019 International MV2019 Kenworth T3702019 Mack MHD2019 Peterbilt 3372019 Western Star 4700



Air conditioninga.Standard full-size spare tire, if availableb.2 keysc.

ENGINE:2.

Diesel engine, minimum 200 HPa.


Manufacturers standard automatic transmission (with PTO provision) minimum, or approved equivalent.a.21,000 lb. rearb.All axles, synthetic lube.c.



COMFORT ITEMS:5.

Air conditioning, factory installed.a.Manufacturer's standard tinted glass all around.b.Manufacturer's standard AM/FM stereo.c.Heavy duty rubber floor covering instead of carpet.d.Manufacturer's standard production seats. Purchaser will select color at time of order.e.Keys: two (2) per vehicle, single key locking system, (each vehicle keyed differently).f.

SAFETY ITEMS:6.

Dual mount outside mirrors must provide a field of vision for vehicles to 102" width, and for towing.a.Convex mirrors mounted below standard mirrors.b.Interior dome lights with left and right door activated switches.c.

BRAKES:7.

Factory air brakesa.Anti-lock brake systemb.

TIRES AND WHEELS:8.

BSW 11R22.5 (14 PR) or approved equivalent, front and rear.a.Oil bath hubs, with synthetic lube.b.


Minimum 30,000 lbs. GVWR.a.Cab & chassis only.b.Manufacturer's standard colors, factory painted. Colors to be determined by individual agencies.c.Manufacturer's standard front bumper, bright or painted.d.Factory front tow hooks.e.Fuel tank capacity, 45 gallons minimum.f.Cab to center of rear axle - 84" approximately.g.


SPECIFICATION #14 - 52,000 LB GVWR CAB & CHASSIS - 4X6 TANDEM AXLETRACTOR (ONLY)

2019 Freightliner M2-1122019 International HX2019 International HV2019 Kenworth T8802019 Mack AN or G Series2019 Peterbilt 5672019 Volvo V Series2019 Western Star 4800




ENGINE:2.

350 HP 6 cylinder diesel engine, manufacturer's 11L minimuma.

TRANSMISSION & CLUTCH:3.

The following or approved equivalents are acceptable: Fuller 14210B 10 Speed Manual with OD1.

a.

ENGINE EQUIPMENT:4.

Alternator – 12 volt 100Aa.Premium engine hosesb.Injection pump – electronic engine controlc.Radiator – aluminum cored.Air restriction monitor – intake mountede.

CAB:5.

Cab – welded steel galvanized or aluminum shell with rust preventative coating.a.Floor covering – black rubber matsb.Seating – driver air suspension mid back, passenger fixed mid back.c.Steering wheel – 18" two spoked.Standard air conditioning & heatinge.

FRAME:6.

Frame – steel construction matched to GVW and mounted body of trucka.Wheelbase – 187"b.Load platform – 161" 56" AFc.Front bumper – painted steeld.Fuel tank – 70 gallon, minimume.Air dryer – Bendix AD9 heated, or approved equivalent.f.5th wheel - stationary with left hand release.g.

SAFETY:7.

Horn – single air trumpeta.Mirrors – West Coast for 102" trailer widths to include 7.5" convex mounted to lower mirror bracket.b.Brakes – "S" cam type 16.5" x 5" Q + front and 16.5" x 7" Q + rear with anti-lock with automatic stability control, or approvedequivalent.

c.

Slack adjusters – Haldex automatic front and rear.d.Daytime running lights.e.Backup alarmf.Electrical plug holder includes glad hand storage.g.Tractor package to include valves, trailer lines & frame accessh.Automatic traction and stability controli.

FRONT AXLE:8.

Axle – 12,000 lb. a.Front wheels – steel 10 hole hub piloted b.Front tires – 11R22.5 Goodyear G397LHS, steer or approved equivalent. c.Front hubs – Ferrous, or approved equivalent. d.Oil type with synthetic lube e.

REAR AXLE:9.

Minimum 40,000 lb. rated axle and suspension a.Rear wheels – steel 10 hole hub piloted b.Rear tires – 11R22.5 Goodyear G124 unisteel traction or approved equivalent. c.Hubs – Ferrous, or approved equivalent. d.Power divider with warning light and buzzer (includes in cab control) e.

ELECTRICAL:10.

Circuit protection – fuses except headlamp and wiper circuits which utilize circuit breakers. a.Hand throttle – electronic hand throttle operated through cruise control when in PTO mode only. b.Engine protection – engine shut down system monitoring high water temp, low oil pressure, high exhaust temp, high transmissiontemp.

c.


SPECIFICATION #15 - 52,000 LB GVWR CAB & CHASSIS - 4X6 TANDEM AXLE TRUCK2019 Freightliner M2-1122019 International HX2019 International HV2019 Kenworth T8802019 Mack AN or G Series2019 Mack MHD2019 Peterbilt 5672019 Volvo V Series2019 Western Star 4700



Air conditioninga.Standard full-size spare tire, if availableb.2 - keysc.

ENGINE:2.


TRANSMISISON & CLUTCH:3.

The following or approved equivalents are acceptable: Fuller 14210B 10 Speed Manual with OD1.

a.

ENGINE EQUIPMENT:4.

Alternator – 12 volt 100Aa.Premium engine hosesb.Injection pump – electronic engine controlc.Radiator – aluminum cored.Air restriction monitor – intake mountede.

CAB:5.

Cab – welded steel galvanized or aluminum shell with rust preventative coating.a.Floor covering – black rubber matsb.Seating – driver air suspension mid back, passenger fixed mid back.c.Steering wheel – 18" two spoked.Standard air conditioning and heatinge.

FRAME:6.

Frame – steel construction matched to GVW and mounted body of truck.a.Wheelbase – 187"b.Front bumper – painted steelc.Fuel tank – 70 gallon, minimumd.Air dryer – Bendix AD9 heated, or approved equivalent.e.

SAFETY:7.

Horn – single air trumpeta.Mirrors – West Coast to include 7.5" convex mounted to lower mirror bracket.b.Brakes – "S" cam type 16.5" x 5" Q + front and 16.5" x 7" Q + rear with anti-lock without automatic traction control, or approvedequivalent.

c.

Slack adjusters – Haldex automatic front and rear.d.Daytime running lights.e.Backup alarmf.

FRONT AXLE:8.

Front axle – 12,000 lb.a.Front wheels – steel 10 hole hub pilotedb.Front tires – 11R22.5 Goodyear G397LHS, steer or approved equivalent.c.Front hubs – Ferrous, or approved equivalent.d.Oil type with synthetic lubee.

REAR AXLE:9.

Rear axle – 40,000 lb. a.Rear wheels – steel 10 hole hub piloted b.Rear tires – 11R22.5 Goodyear G124 unisteel traction or approved equivalent. c.Hubs – Ferrous, or approved equivalent. d.Power divider with warning light and buzzer (includes in cab control) e.

ELECTRICAL:10.


c.


SPECIFICATION #16 - 60,000 LB GVWR CAB & CHASSIS - 4X6 TANDEM AXLE REFUSETRUCK (ONLY)

2019 Autocar ACX642019 Crane Carrier LET22019 Mack TE Series2019 Peterbilt 520



Air conditioninga.Standard full-size spare tire, if availableb.2 - keysc.

ENGINE:2.


TRANSMISISON:3.

Allison 4500 RDS automatic transmissiona.

ENGINE EQUIPMENT:4.

Alternator – 12 volt 100Aa.Premium engine hosesb.Injection pump – electronic engine controlc.Radiator – aluminum core, or approved equivalentd.Air restriction monitor – intake mountede.

CAB:5.

Cab – welded steel galvanized or aluminum shell with rust preventative coating.a.Low cab, forward mounted, tilt type.b.Floor covering – black rubber matsc.Seating – driver air suspension mid back, passenger fixed mid back.d.Steering wheel – 18" two spokee.Standard air conditioning and heatingf.

FRAME:6.

Frame – steel construction matched to GVW and mounted body of truck.a.Wheelbase – 209"b.Front bumper – painted steelc.Fuel tank – 70 gallon, minimumd.Air dryer – Bendix AD9 heated, or approved equivalent.e.

SAFETY:7.

Horn – single air trumpeta.Mirrors – West Coast to include 7.5" convex mounted to lower mirror bracket.b.Brakes – "S" cam type 16.5" x 5" Q + front and 16.5" x 7" Q + rear with anti-lock without automatic traction control, or approvedequivalent.

c.

Slack adjusters – Haldex automatic front and rear.d.Daytime running lights.e.Backup alarmf.

FRONT AXLE:8.

Front axle – 20,000 lb.a.Front wheels – steel 10 hole hub pilotedb.Front tires – 315/8OR/22.5 Goodyear G289c.Front hubs – iron, or approved equivalent.d.Oil type with synthetic lubee.

REAR AXLE:9.

Rear axle – 40,000 lb.a.Rear wheels – steel 10 hole hub pilotedb.

Rear wheels – steel 10 hole hub piloted b.Rear tires – 11R22.5 Goodyear G124 unisteel traction or approved equivalent. c.Hubs – iron, or approved equivalent. d.Power divider with warning light and buzzer (includes in cab control) e.

ELECTRICAL:10.


c.


SPECIFICATION #17 - THE ROOK, TACTICAL VEHICLE2019 Caterpillar 297 with Rook Option


VEHICLE PLATFORM:1.

CAT Multi-terrain loadera.84 HP Diesel Engineb.2 Speed powertrainc.Operating weight 13,000 lbs.d.Fuel Tank 26 gallonse.Hydraulic Quick Couplerf.Enclosed ROPS cab with air conditioner and heaterg.Dual level suspension undercarriage with self level.h.Advanced machine information and control systemi.

CAB ARMORED PROTECTION2.

Bullet proof glassa.NIJ Level IV armor cab reinforcement fabricationb.

ARMORED DEPLOYMENT PLATFORM3.

Integrated video systema.Breaching ramb.Vehicle extraction toolc.Grapple clawd.


SPECIFICATION #18 - COMPACT LOAD AND PACK 9.5 CU YD SELF LOADING REFUSETRUCK

2019 Broyhill 74 DLX


ENGINE1.

70 HP Diesel Engine, EPA complianta.

TRAMISSION2.

Hydrostatic Transmissiona.Four wheel driveb.

ENGINE EQUIPMENT3.

Alternator – 12 volt 100 ampa.Premium engine hosesb.Injection pump – electronic engine controlc.Radiator – aluminum core, or approved equivalentd.

CAB4.

Cab – welded steel galvanized or aluminum shell with rust preventative coating.a.Low cab, forward mountedb.Floor covering- manufacturer or standardc.Seating – driver air suspension.d.Standard air conditioning and heatinge.Tilt Wheelf.

FRAME5.

Operating weight 7,300 lbsa.Frame – steel constructionb.GVWR 12,900 lbsc.Wheelbase – 108"d.Front bumper – painted steele.Fuel tank – 30 gallon, minimumf.Articulated jointg.

SAFETY6.

Horn – Electrica.Mirrors – West Coast to include 7.5" convex mounted to lower mirror bracket.b.Brakes – Hydro-static, fail safe parking and emergency brakec.Backup alarmd.Work lightse.Strobe lightsf.DOT compliant lightingg.Windshield wipers 2 speedh.Three Camera system view both sides and reari.

HYDRAULIC SYSTEM7.

Variable displacement hydraulic pumpsa.Hydraulic tank 20 gal capacityb.Hydraulic filters 5 and 10 micronc.Load arm, grip 55-90 gallon containersd.Load arm, 500 LB lift capacitye.Load arm, 5 second cycle timef.

AXLES8.

Dana Corp 70 series front and rear, or approved equivalent.a.Front and Rear tires – 36 x 13.50-15 NHS high floatation tires.b.Hubs – iron, or approved equivalent.c.

ELECTRICAL9.

Circuit protection – fuses except headlamp and wiper circuits which utilize circuit breakers. a.Hand throttle b.Engine protection – engine monitoring system for high water temp, low oil pressure, high exhaust temp, high transmission temp. c.


SPECIFICATION #19 - 15 FT. FLEX WING ROTARY MOWER - PTO DRIVEN2019 Woods BW15.502019 Alamo Eagle 152019 Bush Hog 38152019 John Deere HX152019 Landpride Batwing (RC5615)2019 Rhino 41502019 Schulte FX-1800


DECK:1.

Mower shall be rotary, flex wing style.a.10 gauge steel minimumb.Replaceable full length skid shoesc.Shall be easy clean styled.

BLADE CARRIER & BLADES:2.

7 gauge steel minimuma.1 inch thick cross bar weldmentb."Stump Jumper" pan designc.2 free swinging updraft cutting blades 1/2 inch thick, heat treated alloy steel minimumd.Blades shall overlap a minimum of six inches for uniform cut.e.Blade spindles shall be 1 1/4 inch diameter minimum.f.

WHEELS/TIRES:3.

6 replaceable puncture resistant foam filled airplane tailwheels.a.

POWER DISTRIBUTION:4.

Main driveline shall be CAT 5a.Slip clutch protection shall be featured.b.Gears shall be straight bevel with tapered roller bearings.c.A power divider shall have a rating of 190 HP minimum.d.Center and wing gearboxes shall have a minimum rating of 190 HP.e.

GENERAL FEATURES:5.

Mower shall attach to the rear of the tractor using a self level-lift hitch.a.Front and rear chain deflectors.b.Tounge shall have a jack stand.c.


SPECIFICATION #20 - ZERO TURN RADIUS COMMERCIAL GRADE MOWER2019 Cub Cadet Pro Z 560 L/S KW2019 Bad Boy Outlaw 61002019 Dixie Chopper 2560 BR2019 Grasshopper Model 2252019 Gravely Proturn 2602019 John Deere Z930M2019 Kubota Z725KH-2-602019 Scag Cheetah SCZ61V-27FX


ENGINE:1.

25 horsepower gas enginea.7 gallon fuel tankb.Positive feed oil system with spin on filter.c.Heavy duty air cleanerd.Electric starte.

DRIVE TRAIN/AXLES:2.

Hydraulic gear pumpsa.High torque wheel motorsb.Spin on hydraulic filtersc.

DECK:3.

60" heavy duty mower decka.3 blade spindlesb.Belt drivenc.Manual deck liftd.1" to 5" cutting heighte.Deck engagement electric clutchf.

WHEELS:4.

Front wheels - 13x6-6 ribbed, minimuma.Rear wheels - 24x11.5-12 turfb.

COMFORT & CONVENIENCE:5.

High back full suspension seata.Adjustable steering/motion control leversb.Flip up hoodc.Easy access operator controlsd.ROPS bare.

APPROXIMATE MACHINE DIMENSIONS:6.

Length - 82"a.Height - 72" with ROPSb.Width - 63" without chutec.

CONDITIONS:7.

In addition to equipment specified, mower will be equipped with all standard equipment as specified by the manufacturer for thismodel and shall comply with all EPA emission standards and all motor vehicle standards as established by the U.S. Department ofTransportation regarding the manufacture of motor vehicles.

a.

The successful bidder shall be responsible for delivering the unit properly serviced, clean and in first class operating condition.Pre-delivery service at a minimum shall include the following:

Complete lubrication1.Check all fluid levels2.

b.

Adjustment of engine to proper operating conditionc.Inflate tires to proper pressured.Proper operation of all accessories.e.


SPECIFICATION #21 - REMOTE CONTROLLED BRUSH MOWER2019 Alamo Ridgerunner


APPROXIMATE DIMENSIONS1.

Length- 57"a.Width- 59"b.Height- 33"c.Weight- 990 lbsd.

ENGINE2.

24 hp. 2 cylinder gasa.Pressurized oiling systemb.Electric start w/ 16v , 16 a alternatorc.5 gal fuel capacityd.

TRACK DRIVE SYSTEM3.

Two 48v electric motorsa.Infinitely variable gear reduction transmissionsb.Multi lug type tracksc.Neoprene rollersd.

MOWER DECK4.

Twin spindle decka.10 gage mower deckb.Blade bar 2x22" with 4 free swinging bladesc.Electric clutch assembly w/ integral safety braked.Mowing heigth range 2 to 7 "e.

REMOTE CONTROL5.

Remote control to control mower functions: travel speed, cutting height, hours, radio signal strength. state of charge of remotecontrol battery, and mower on/off

a.

Remote control working range 328 ft. , max range 984 ft.b.Auto stop feature for loss of radio signalc.Rechargeable lithium ion batteriesd.

SAFETY6.

One touch emergency shut off switcha.Warning beaconb.


SPECIFICATION #22 - LARGE TOOL CARRIER WITH OPTIONAL MOWERATTACHMENTS

2019 Mantis 41422019 MowerMax Industrial Tool Carrier2019 Multihog Range MX

This equipment bid is for the tool carrier only, without attachments. Buyer mustselect the attachments desired from the option list to complete the equipment, whichwill affect the final price.

ENGINE1.

99.9 HP Tier III Turbo Diesela.Heavy duty radiator with high flow fan with reversing, clean out valveb.Canister style air cleaner with pre-cleanerc.Electric start with engine pre-heatd.Full engine gauge packagee.30 gallon fuel tankf.

POWER TRAIN2.

Hydrostatic, variable displacement piston transmission pump in a closed loop systema.Two, heavy-duty, 4 wheel drive, steerable axles with parking and service brakeb.3 steering modes – 4 wheel round, front wheel and 4 wheel crabc.High torque, two-speed, hydraulic piston drive motor for front axle and drive shaft for rear axled.Joystick for speed and directional (forward/reverse) controle.GVW (without attachments): Approximately 9000lbsf.

TRAVEL SPEED3.

Work Mode – Variable 0-5 MPHTravel Mode – Variable 0-20 MPHa.

WHEELS4.

Standard -15-19.5 Industrial tiresOptional - 38x18.00-20 Lug tiresa.

COMFORT, CONVENIENCE & SAFETY5.

Full air ride, suspension seat with lumbar support and integrated operator-presence safety switcha.Certified ROPS Canopy with AC, Heat, AM/FM radio with Bluetootthb.Tilt steering column with hornc.Seat belt with safety switchd.Turn Signals and brake lightse.Flashing safety lights as well as DOT reflector tapef.Engine gauge packageg.

ATTACHMENT OPTIONS6.

Front lift arms with universal skid steer mounting plate for 10+ skid steer attachments: Broom/sweeper1.90 inch rotary mower2.88 in flail mower3.Dozier blade4.Stump grinder5.Pallet forks6.Cold planer7.Big roll sod installer8.Landscape rake9.Rotary tiller10.

a.

Right side rotary mowerb.Right side flail mowerc.Right side boom/reach mowerd.15 ft belly mowere.

CONDITIONS7.

The successful bidder shall be responsible for delivering the unit properly services, clean and in first class operating condition.Pre-delivery service at a minimum shall include:

Proper operation of all accessories1.

a.

Check all fluids 2.Complete lubrication 3.Adjustment of engine to proper operation condition 4.Inflate tires to proper operating pressure 5.

In addition to equipment specified, mower will be equipping with all standard equipment as specified by the manufacturer for thismodel and shall comply with all EPA emission standards and all motor vehicle standards as established by the US Department ofTransportation regarding the manufacturer of motor vehicles.

b.


SPECIFICATION #23 - TELESCOPIC TOOL CARRIER2019 Bobcat Versa Handler V723 Telehandler2019 Caterpillar TH357D2019 JLG G5-18A

Incomplete equipment. Unit bid is for the prime mover only, without attachments.Buyer should select attachments needed from the option list to complete the machine.Examples of attachments available are: Bucket; grapple and/or forks. This willaffect the total price.


Length: 196 ina.Width: 90 inb.Height, w/cab: 93 inc.Wheelbase : 113 in.d.Weight: 17,155 lbs.e.

ENGINE2.

Diesel, Tier 4 100hpa.Turbochargedb.Heavy duty cooling systemc.

POWERTRAIN3.

Hydrostatic Drivea.2 Travel speeds low speed 3.0 mph, high speed 18 mphb.All wheel drivec.3 Steering modes: all wheel, crab, and front wheeld.Industrial lug type tirese.

COMFORT, CONVENIENCE AND SAFETY4.

Certified ROPs cab with a/c, heata.Suspension seat w/ seat beltb.Work lights, safety lights, and warning beaconc.Attachment controls in cabd.Engine gauge instrumentatione.

HYDRAULIC SYSTEM5.

Lift capacity 7700 lbsa.Max lift 22 feetb.Boom breakout force : 8000 lbsc.


SPECIFICATION #24 - COMPACT CENTER ARTICULATING TRACTOR - AWD2019 Ventrac 3400 Series2019 Ventrac 4500 Series


ENGINE1.

3400L - Briggs & Stratton 20hp Vanguard 385800a.4500K - Briggs & Stratton 31hp Vanguard M54b.

TRANSMISSION2.

Manufacturer's standard hydrostatic.a.

PERFORMANCE ITEMS3.

Manufacturer's standard power steeringa.SDLA controls for complete one-handed control of Speed, Direction, Lift & Auxiliary functionsb.Weight Transfer – transfers weight to front axle for added stability (optional on 3400L & 4500K)c.

SAFETY ITEMS4.

Automatic PTO shut-off- when weight is removed from seata.Standard seatbelt (optional 4-point harness)b.Standard ROPS systemc.Neutral Assistd.

TIRES AND WHEELS5.

Manufacturer's standard tires and wheels (optional turf or bar tires)a.Optional Dual wheel tires for safe maneuvering on slopes up to 30 degrees (58% grade)b.

ATTACHMENT AND ACCESSORIES6.

30+ commercial grade attachments for a variety of applications (sold individually, not factory installed)a.Uses Ventrac quick hitch system for quick transition between applicationsb.


SPECIFICATION #25 - SMALL AGRICULTURE TYPE TRACTOR (4 WHEEL DRIVE)2019 Case IH Farmall 35C2019 John Deere 3039R2019 Kubota L3901 DT2019 Mahindra 16402019 Massey Ferguson 1739E2019 New Holland Boomer 35


ENGINE:1.

Liquid cooled diesel with minimum of 29 PTO hp @ 2200 rpm.a.

TRANSMISSION:2.

Hydrostatic drive or mechanical type transmission.a.

FUEL TANK:3.

Minimum 7 gallon capacity.a.

BRAKES:4.

Oil cooled hydraulic wet disc.a.

POWER TAKE OFF:5.

Speeds RPM - 540a.

HYDRAULIC SYSTEM:6.

Open center system with standard remotes.a.Maximum main pump flow - 6.3 gpmb.

3 POINT HITCH:7.

Category Ia.SAE lift capacity @ 24" standard lbs. - 1,435b.

TIRES:8.

Not less than 11.2 x 24 reara.Not less than 5-15 6 ply frontb.


SPECIFICATION #26 - AGRICULTURE TYPE TRACTOR (2 WHEEL DRIVE)2019 Case IH Farmall 100C2019 Challenger MT4552019 John Deere 5100M2019 Kubota M5-0912019 Mahindra mForce 105S2019 Massey Ferguson 47092019 New Holland Powerstar 100


ENGINE:1.


TRANSMISSION:2.

Synchroshuttle type with a minimum of 8 forward and 3 reverse speeds.a.

FUEL TANK:3.


BRAKES:4.

Oil cooled hydraulic.a.

POWER TAKE OFF:5.

Speeds RPM - 540/1000a.

HYDRAULIC SYSTEM:6.

Open center system with standard remotes.a.Standard output @ remote gpm - 10b.Main pump flow 17 gpmc.

POINT HITCH:7.

Electronic or mechanical 3 point hitch controla.Category IIb.Telescopic stabilizersc.SAE lift capacity @ 24" standard lbs. - 3,600d.Lower draft arm link ends - extendablee.

TIRES:8.

Not less than 18.4R - 28 R1 radialsa.Not less than 7.5L - 15 6 Ply F2b.


SPECIFICATION #27 - AGRICULTURE TYPE TRACTOR WITH BOOM MOWER (4WHEEL DRIVE)

2019 Case IH Maxxum 115 with Motrim Boom Mower2019 Challenger MT465 with Diamond Boom Mower2019 John Deere 6120M Alamo Industrial Mower2019 John Deere 6120M with Tiger Bengal Boom Mower2019 Kubota M6S-111 with Terrain King KB2300 Boom Mower2019 Massey Ferguson MF5712SL with Diamond Boom Mower2019 New Holland TS6.120 with Alamo Boom


ENGINE:1.


TRANSMISSION:2.

Synchroshuttle type with a minimum of 16 forward and 16 reverse speeds.a.

FUEL TANK:3.


BRAKES:4.

Oil cooled hydraulic.a.

POWER TAKE OFF:5.

Speeds RPM - 540/1000a.

HYDRAULIC SYSTEM:6.

Closed center system with standard remotes.a.Maximum pressure psi - 2,900b.Standard output @ remote 17 gpmc.Total of 29 gpm combined flowd.

POINT HITCH:7.

Category IIa.Telescopic stabilizersb.SAE lift capacity @ 24" standard lbs. - 5,000c.Lower draft arm link ends - extendabled.

TIRES:8.

Not less than 13.6R24 R1 rear radialsa.Not less than 18.4R30 6 Ply F2b.

MOUNTED BOOM MOWER:9.

Minimum 23' boom reach.a.Forward and reverse swing break away.b.Integral frame.c.Separate hydraulic circuit for mower head.d.5' rotary cutter head.e.Disc or bar type blade holder.f.


SPECIFICATION #28 - 4X4 LOADER BACKHOE WITH CANOPY (STANDARD STICK)2019 Case 580 SN2019 Caterpillar 4162019 John Deere 310SL


ENGINE:1.

Minimum 87 HP Diesel enginea.Dry type, radial seal air cleaner and pre-cleaner unitb.Spin on type engine oil filterc.

TRANSMISSION:2.

Four speed power shift or power shuttle transmissiona.

OPERATOR ENVIRONMENT:3.

OSHA approved ROPS canopy shall be integrala.Two front and two rear work and driving lightsb.Stop and turn signals with flashing hazard lampsc.Instrument panel with a complete set of gauges or an electronic monitoring deviced.Standard horn and audible back-up alarme.

BRAKES:4.

Brakes shall be oil immersed, hydraulically actuated, multiple disc on final drive input shafta.Brakes shall be completely enclosed and sealed, fully self-adjustingb.

LOADER (SINGLE TILT CYLINDER):5.

Loader shall be equipped with a return to dig mechanisma.Loader shall have positive down pressure sufficient to lift the tractor front end off level groundb.Loader bucket SAE heaped capacity of minimum 1.3 yards with replaceable bolt on edgec.

BACKHOE:6.

Fixed length dipper stick digging depth approximately 14'a.Reach from swing center, approximately 18'b.Dump height, approximately 11'3"c.Digging force approximately 8,000 lbs.d.Bucket dig force, approximately 11,990 lbs.e.24" general purpose bucket with replaceable teethf.


SPECIFICATION #29 - SKID STEER LOADER - 1850 LB OPERATING CAPACITYWHEELED ONLY

2019 Bobcat S5702019 Case SV1852019 Caterpillar 236D2019 John Deere 318G2019 Kubota SSV652019 Takeuchi TS60V2019 Volvo MC95C


ENGINE:1.

Minimum 3 cylinder 56 HP Diesela.

TRANSMISSION:2.

Hydrostatic Drivea.Forward, reverse, travel speed controlled by two hand leversb.

ENGINE EQUIPMENT:3.

Spin on type filtersa.Dry type air filterb.


OSHA approved ROPS canopy shall be integrala.Front and rear work lights, hazard lightsb.Engine monitoring system or gauges, with audible alarmc.Tires 10x16.5 extra walld.Horn and backup alarme.

BRAKES:5.

Parking brakea.Hydrostatic main brakingb.

LOADER:6.

Front auxillary hydraulicsa.Foot or hand controls for bucketb.Minimum 62" wide construction bucketc.Operating capacity 1,800 lbs - minimumd.


SPECIFICATION #30 - SKID STEER LOADER - 2800 LB OPERATING CAPACITYWHEELED ONLY

2019 Bobcat A7702019 Bobcat S7702019 Case SV3402019 Caterpillar 272D2019 John Deere 330G2019 Volvo MC 135D


ENGINE:1.

Minimum 3 cylinder 83 HP Diesela.

TRANSMISSION:2.

Hydrostatic drivea.Forward, reverse, travel speed controlled by two hand leversb.

ENGINE EQUIPMENT:3.

Spin on type filtersa.Dry type air filtersb.


OSHA approved ROPS canopy shall be integrala.Front and rear work lights, hazard lightsb.Engine monitoring system or gauges, with audible alarmc.Horn and backup alarmd.Tires 14x17.5 extra walle.

BRAKES:5.

Parking brakea.Hydrostatic brakingb.

LOADER:6.

Front auxillary hydraulicsa.Foot or hand controls for bucketb.Minimum 84" wide construction bucketc.


SPECIFICATION #31 - SKID STEER LOADER - 3100 LB OPERATING CAPACITYTRACKED ONLY

2019 Bobcat T7402019 Case TR3102019 Caterpillar 279D2019 John Deere 331G2019 Kubota SVL75-22019 Takeuchi TL122019 Volvo MCT135D


ENGINE:1.

Minimum 3 cylinder 74 HP Diesel a.Spin on type filters b.Dry type air filters c.

TRANSMISSION:2.

Hydrostatic drive a.Forward, reverse, travel speed controlled by two hand levers b.


OSHA approved ROPS canopy shall be integral a.Front and rear work lights, hazard lights b.Engine monitoring system or gauges, with audible alarm c.Horn and backup alarm d.

BRAKES:4.

Parking brake a.Hydrostatic braking b.

BUCKET:5.

Minimum 66" construction bucket a.Bolt on, replaceable cutting edge for bucket b.Operating capacity 3,100 lbs. minimum c.


SPECIFICATION #32 - 1.5 CU YD WHEEL LOADER (Z-BAR LINKAGE BUCKET -PARALLEL ARM OPTION)

2019 Case 321F2019 Caterpillar 908M2019 Hitachi ZW1202019 John Deere 324L2019 Volvo L45H2019 Takeuchi TW80


ENGINE/CAB:1.

Diesel engine, six cylinder, four cycle, liquid cooled, minimum 77 HPa.Cab with A/Cb.

TRANSMISSION:2.

Power shift transmission with torque converter or hydrostatic drive, minimum of four forward and three reverse speeds.a.

DRIVETRAIN:3.

Four wheel drive.a.Manufacturer's standard axle.b.Inboard or outboard mounted wet disc braking system.c.Inboard or outboardmounted plantetary final drives.d.15.5 – 25 Bias ply tires mounted on multi piece rims.e.

LOADER:4.

1.5 cu. yd. general purpose bucket with bolt on cutting edge.a.Bucket position indicator.b.Automatic return to dig.c.Rear drawbar.d.Gauges and indicators: visual hydraulic oil level indicator, electronic monitor display of all fluid levels and temperatures.e.Deluxe suspension seat with foam padding and backrest.f.Articulated steering, clearance circle 34'.02"g.Wheelbase of at least 7'h.Minimum operating weight of 12,727 lbs.i.

ELECTRICAL:5.

12 or 24 volt electrical system.a.Manual battery disconnect switch.b.Driving lights, front and rear work lights, stop lights, warning lights and tail lights.c.


SPECIFICATION #33 - 3.0 CU YD WHEEL LOADER (Z-BAR LINKAGE BUCKET -PARALLEL ARM OPTION)

2019 Case 621G2019 Caterpillar 926 M2019 Doosan DL220-52019 Doosan DL280-52019 Hitachi ZW1802019 John Deere 524L2019 Volvo L60H


ENGINE/CAB:1.

Diesel engine, six cylinder, four cycle, liquid cooled, minimum 140 SAE Net HPa.Cab with A/Cb.

TRANSMISSION:2.


DRIVETRAIN:3.

Four wheel drive.a.Manufacturer's standard axle.b.Inboard or outboard mounted wet disc braking system.c.Inboard or outboardmounted plantetary final drives.d.20.5 – 25 Bias ply tires mounted on multi piece rims.e.

LOADER:4.

3.0 cu. yd. general purpose bucket with bolt on cutting edge.a.Bucket position indicator.b.Automatic return to dig.c.Rear drawbar.d.Gauges and indicators: visual hydraulic oil level indicator, electronic monitor display of all fluid levels and temperatures.e.Deluxe suspension seat with foam padding and backrest.f.Articulated steering, 40 degrees minimum each directiong.Wheelbase of at 9 feet, 4 inches minimumh.Minimum operating weight of 26,000 lbs.i.

ELECTRICAL:5.

12 or 24 volt electrical system.a.Manual battery disconnect switch.b.Driving lights, front and rear work lights, stop lights, warning lights and tail lights.c.


SPECIFICATION #34 - 5.75 CU YD WHEEL LOADER (Z-BAR LINKAGE BUCKET)2019 Case 1021 G2019 Caterpillar 972M2019 Doosan DL450-52019 John Deere 744K-22019 Hitachi ZW3102019 Volvo L150H


ENGINE/CAB:1.

Diesel engine, six cylinder, four cycle, liquid cooled, minimum 280 HP.a.Cab with A/Cb.

TRANSMISSION:2.


DRIVETRAIN:3.

Four wheel drive.a.Manufacturer's standard axle.b.Inboard or outboard mounted wet disc braking system.c.Inboard or outboardmounted plantetary final drives.d.26.5 –R25 radial tires mounted on multi piece rims.e.

LOADER:4.

5.75 cu. yd. general purpose bucket with bolt on cutting edge.a.Bucket position indicator.b.Automatic return to dig.c.Rear drawbar.d.Gauges and indicators: visual hydraulic oil level indicator, electronic monitor display of all fluid levels and temperatures.e.Deluxe suspension seat with foam padding and backrest.f.Articulated steering, 40 degrees minimum each direction.g.Wheelbase of 11'4" minimum.h.Minimum operating weight of 53,674 lbs.i.

ELECTRICAL:5.

24 volt electrical system.a.Neutral safety start device.b.Manual battery disconnect switch.c.Driving lights, front and rear work lights, stop lights, warning lights and tail lights.d.


SPECIFICATION #35 - MOTORGRADER - SMALL2019 LBP G-7002019 Lee Boy 685B2019 Mauldin MG6182019 Noram 65E Grader



Length 21'a.Width 7'b.Height with cab 10'4"c.Weight 15,200 lbs.d.

ENGINE:2.

Diesel, turbocharged 110 HP.a.Dual stage air cleanerb.39 gallon fuel tankc.

DRIVE TRAIN3.

Hydrostatic drive or power shifta.2 speed gear boxb.

BRAKES:4.

Fail safe brake systema.

STEERING/ARTICULATION:5.

18 degree articulation left or righta.Front wheel leanb.

MOLDBOARD/BLADE6.

10' Sliding/Tilting moldboarda.10' Bladeb.Circle side shiftc.Scarifier - center mount, front mount or rear mount acceptable.d.Adjustable turn tablee.Blade float controlf.

OPERATORS STATION:7.

Enclosed caba.Front and rear windshield wipersb.Suspension seatc.Air conditioned and heated cabd.Gauge packagee.Work lightsf.


SPECIFICATION #36 - MOTORGRADER2019 Case 865B2019 Caterpillar 120M2019 John Deere 620G


ENGINE:1.

Liquid cooled 6 cylinder diesel with minimum of 140 net hp @ 1900 RPM..a.

TRANSMISSION:2.

Power shift with direct drive.a.Minimum 8 forward and 4 reverse speeds.b.

BRAKES:3.

Wet multiple disc.a.

STEERING & ARTICULATION:4.

Front steer plus articulated.a.Minimum articulation 20 degrees.b.

MOLDBOARD:5.

Minimum 12 ft. long.a.


Low profile cab.a.Cloth adjustable seats.b.Gauges including hour meter, fuel, articulation, engine coolant temperature.c.

TIRES:7.

Minimum 13.0 – 24 10 PR 9" single piece rim.a.


SPECIFICATION #37 - 70 HP BULLDOZER CANOPY TRACTOR (STANDARD TRACK -WIDE TRACK OPTIONAL)

2019 Case 650M2019 Caterpillar D32019 John Deere 450K


ENGINE:1.

Minimum 4 cylinder 70 Net HPa.

TRANSMISSION:2.

Hydrostatic, infinitely variable speed.a.Constantly variableb.

UNDERCARRIAGE:3.

Minimum 5 rollersa.Standard grouser minimum of 16"b.Top roller, each sidec.

DOZER:4.

Minimum 96" widea.Minimum 32" highb.Minimum 1.88 cyd blade capacityc.Power, angle, tilt (PAT) type bladed.


SPECIFICATION #38 - 90 HP BULLDOZER CANOPY TRACTOR (STANDARD TRACK -WIDE TRACK OPTIONAL)

2019 Case 850M2019 Caterpillar D42019 John Deere 650K


ENGINE:1.

Minimum 4 cylinder 90 Net HP a.

TRANSMISSION:2.

Hydrostatic, infinitely variable speed. a.Constantly variable b.

UNDERCARRIAGE:3.

Minimum 6 rollers a.Standard grouser minimum of 18" b.Top roller, each side c.

DOZER:4.

Minimum 104" wide a.Minimum 36" high b.Minimum 2.5 cyd blade capacity c.Power, angle, tilt (PAT) type blade d.


SPECIFICATION #39 - 180 HP BULLDOZER CANOPY TRACTOR2019 Case 2050M2019 Caterpillar D6T2019 John Deere 850K


ENGINE:1.

Minimum 6 cylinder 180 H.P. diesel enginea.

TRANSMISSION:2.

Power shift or hydrostatic drivea.Power shift to have 3 forward and reverse gear ranges minimumb.Hydrostatic drive to be variablec.

UNDERCARRIAGE:3.

7 rollers each side minimuma.Top roller each side minimumb.Manufacturers standard length trackc.Manufacturers standard track widthd.24" grouser widthe.

DOZER BLADE:4.

128" widea.48" highb.2.5 cubic yard blade capacityc.PAT type blade, power angle and tilt, hydraulically controlledd.

OPERATING WEIGHT:5.

Minimum Operating Weight - 43,000 LBS.a.


SPECIFICATION #40 - ALL TERRAIN WALKING EXCAVATOR2019 Kaiser S22019 Menzi Muck M3


WEIGHT:1.

15,873 lbs. 2x4a.17,196 lbs. 4x4b.

ENGINE/CAB:2.

Diesel engine, minimum 95 net horsepowera.Roll over enclosed cab air conditioned and heated.b.Hinged quick release side window for emergency exit (operational at all boom positions).c.Hinged front window opening outward for safety (not inward reducing operator head room).d.Gauges or warning indicators for fuel level, engine oil, hydraulic oil and coolant.e.Mirrorsf.Air sprung operators seatg.Full size cab (width of machine) for operator comfort and room with toolbox.h.

TRAVEL SYSTEM:3.

Minimum high speed travel - 5 mpha.Minimum grade-ability 70%b.Four tiresc.

HYDRAULIC SYSTEM:4.

Piston type hydraulic pumps.a.Digging depth - 15'4"b.Auxiliary hydraulic circuit and controls plumbed to the end of stick with disconnect to allow the use of hydro-mechanical worktools.

c.

Hydraulic motor-driven swing system.d.Stabilizers to be individually controlled in the vertical and horizontal positions.e.Boom assembly hydraulic hoses mounted on left side in operator's field of vision.f.

ELECTRICAL SYSTEM:5.

12 or 24 volta.30 amp alternatorb.Work lightsc.

BUCKET:6.

4' wide grading bucketa.


SPECIFICATION #41 - HYDRAULIC MINI EXCAVATOR - 7,105 LB OPERATINGWEIGHT

2019 Bobcat E32 T42019 Case CX33C2019 Caterpillar 303E CR2019 Hitachi ZX35-U-52019 John Deere 35G2019 Kobelco SK35SR2019 Kubota U35-42019 Sany SY352019 Takeuchi TB2402019 Volvo EC 35 D2019 Yanmar Vi035-6A


WEIGHT:1.

7,105 minimum capacity weight with canopya.

ENGINE/CAB:2.

Diesel engine, minimum 23 net horse powera.Rollover and falling object protective structuresb.Gauges or warning indicators for fuel level, engine oil, hydraulic oil and coolant.c.

TRAVEL SYSTEM:3.

Minimum high speed travel 2.3 MPHa.Minimum gradeability, 20 degreesb.11" wide rubber belt tracksc.

HYDRAULIC SYSTEM:4.

Gear type hydraulic pumpa.Digging depth 9' minimumb.Auxiliary hydraulic circuit and controls plummed to the end of stick with disconnect to allow the use of hydro-mechanical worktools

c.

Backfill bladed.Hydraulic motor-driven swing systeme.


12 volt electrical systema.40 amp alternatorb.Sealed electrical connectorc.Work lightsd.


SPECIFICATION #42 - HYDRAULIC EXCAVATOR - 15,590 LB OPERATING WEIGHT2019 Bobcat E852019 Case CX75C2019 Caterpillar 308E2 2019 Doosan DX85R-32019 Hitachi ZX75US-52019 John Deere 75G2019 Kobelco SK-75SR-3E2019 Kubota KX080-4S2019 Link-Belt 75X32019 Sany SY752019 Takeuchi TB2902019 Volvo ECR88D


WEIGHT:1.

Minimum operating weight 15,590 lb.a.

ENGINE:2.

Diesel engine, 53 horsepowera.Spin on type filterb.Two stage air cleanerc.

TRAVEL SYSTEM:3.

Travel speed of 3.0 mpha.

HYDRAULIC SYSTEM:4.

Standard auxiliary hydraulic valvea.Main hydraulic system flow 33.8 GPMb.

UNDERCARRIAGE:5.

Overall track length 9'1"a.Overall track width 11' minimum 7'6"b.Shoe width 17.7" minimumc.

OPERATING STATION:6.

Cab to be air conditioned, heated and pressurized filtration systema.Intermittent windshield wipersb.Opening front windshieldc.Vibration dampening cab mountsd.Adjustable suspension type operator seat with safety belte.Tinted safety glassf.Engine monitoring system with audible alarmsg.Work lightsh.

STICK, BOOM, BUCKET:7.

Boom and stick combination to allow minimum reach at ground level of 20'11"a.Bucket to be general purpose bucket, appropriately sized for machine and included.b.

SWING SYSTEM:8.

Swing radius 5' approximatea.Swing speed 9.0 rmpb.

MISCELLANEOUS:9.

Fuel capacity of 26 gallonsa.


SPECIFICATION #43 - HYDRAULIC EXCAVATOR - 38,000 LB OPERATING WEIGHT2019 Case CX160D2019 Caterpillar 316F2019 Doosan DX180LC-52019 Hitachi ZX160LC-62019 John Deere 160GLC2019 Kobelco SK170LC2019 Link-Belt 160X42019 Volvo EC160EL


WEIGHT:1.

Minimum operating weight - 38,000 lbsa.

ENGINE:2.

Turbocharged diesel engine 113 hpa.Spine on filtersb.Two stage air cleanerc.

TRAVEL SYSTEM:3.

Travel speed of 3.2 mpha.

HYDRAULIC SYSTEM:4.

Standard auxiliary hydraulic valvea.main hydraulic system flow 72 GPM minimumb.

UNDERCARRIAGE:5.

Overall track length 12' 10" minimuma.Overall track width 8'5" minimumb.Shoe width 24"c.


Cab to be air conditioned, heated and pressurized filtration systema.Intermittent windshield wipersb.Opening front windshieldc.Vibration dampening cab mountd.Adjustable suspension type operator seat with safety belte.Work lightsf.


SPECIFICATION #44 - HYDRAULIC EXCAVATOR - 76,550 LB OPERATING WEIGHT2019 Case CX350D2019 Caterpillar 3362019 Doosan DX350LC-5K2019 Hitachi ZX350LC-62019 John Deere 350GLC2019 Kobelco SK350LC2019 Link-Belt 350X42019 Sany SY3652019 Volvo EC350 E


WEIGHT:1.

Minimum operatiing weight - 76,550 a.

ENGINE:2.

Turbocharged diesel engine 257 HP a.Spin on type filters b.Two stage air cleaner c.

TRAVEL SYSTEM:3.

Travel speed of 2.9 mph a.

HYDRAULIC SYSTEM:4.

Standard auxilliary hydraulic valve a.Main hydraulic system flow 144 GPM minimum b.

UNDERCARRIAGE:5.

Overal track length 16'2" a.Overall track width 10'6" b.Shoe width 24" c.

OPERATING STATING:6.

Cab to be air conditioned, heated and pressurized filtration system a.Intermittent windshield wipers b.Opening front windshield c.Vibration dampering cab mounts d.Adjustable suspension type operator seat with safety bel e.Tinted safety glass f.Engine monitoring system with audible alarm g.Work lights h.


Boom and stick combination to allow minimum reach at ground level of 35'6" a.Bucket to be a general purpose bucket, appropriately sized for machine and included b.

SWING SYSTEM:8.

Swing radius 12 a.Swing speed 9.2 RPM b.

MISCELLANEOUS:9.

Fuel capacity of 145 gallons minimum a.


SPECIFICATION #45 - HYDRAULIC EXCAVATOR, WHEELED TYPE - 42,000 LBOPERATING WEIGHT

2019 Caterpillar M3182019 Doosan DX210WE-52019 John Deere 190 GW2019 Volvo EW180E


WEIGHT:1.

Minimum operating weight - 42,000 lbs. a.

ENGINE:2.

Turbocharged diesel engine 140 hp a.Spin on type filters b.Two stage air cleaner c.

TRAVEL SYSTEM:3.

Travel speed of 21 mph a.

HYDRAULIC SYSTEM:4.

Standard auxiliary hydraulic valve. a.Hydraulic system flow 99 gpm minimum. b.

WHEEL DRIVE:5.

Wheelbase 8' minimum a.Tire size 10:00x20 b.Ground clearance 13" minimum c.Gradability 61 percent d.


Cab to be air conditioned, heated, and pressurized filtration system. a.Intermittent windshield wipers. b.Opening front windshield. c.Vibration dampening cab mounts. d.Adjustable suspension type operator seat with safety belt. e.Tinted safety glass. f.Engine monitoring system with audible alarms. g.Work lights. h.Tail, stop, turn, and emergency flashers. i.


Boom and stick combination to allow minimum reach at ground level of 30' minimum. a.Bucket to be a general purpose bucket, appropriately sized for machine and included. b.

SWING SYSTEM:8.

Swing radius 7 ft. approximate. a.Swing speed 9.5 rpm minimum. b.

MISCELLANEOUS:9.

Fuel capacity of 77 gallons minimum. a.

BLADE/OUTRIGGERS:10.

Front blade with 8' minimum a.Rear outriggers b.


SPECIFICATION #46 - TELESCOPIC EXCAVATOR, TRACK TYPE - 45,000 LBOPERATING WEIGHT

2019 Gradall 4200


WEIGHT:1.

Minimum operating weight 45,000 lbs. a.

ENGINE:2.

4 cylinder turbocharged diesel, 170 HP at 2200 RPM a.Spin on type filters b.Two stage air cleaner c.12 volt 100 AMP alternator d.90 gallon fuel capacity e.

TRACK DRIVE:3.

Two speed, automatic with manual override a.High torque piston motors each track b.Planetary drives c.Travel speed high 3.4 MPH, Low 1.9 MPH d.Automatic parking brake e.Individual track control f.

TRACKS:4.

23.6 pad size a.

OPERATOR'S STATION:5.

Acoustical lined a.Adjustable seat b.Tinted safety glass c.Filtered fresh air d.Heater, air conditioned, and defroster e.Wipers and washers f.Skylight g.Work lights h.

OPERATOR'S STATION CONTROLS:6.

Electric engine monitoring system a.Auto idle b.Electronic joysticks on adjustable pedestals c.Pedals for travel and steering d.Low/high travel switch e.Engine speed control f.

SAFETY ITEMS:7.

Electric horn a.Movement alarm b.Fire extinguisher c.Mirrors, right and left side d.

HYDRAULIC SYSTEM:8.

Hydraulic oil cooler a.120 HP track drive motors (each) b.64 HP swing motor c.Electronic hydraulic system monitor d.Spin on hydraulic filters e.Swing speed 7.0 RPM f.Automatic swing brake g.

BOOM:9.

Telescopic boom a.180 degree boom rotation b.30' reach at ground level from center pivot to buck cutting edge c.

BUCKET:10.

60" ditching bucket provided with machine a.Quick attach type b.


SPECIFICATION #47 - TELESCOPIC EXCAVATOR, WHEELED 6X6 - 47,000 LBOPERATING WEIGHT

2019 Gradall XL4100


WEIGHT:1.


CARRIER:2.

Carrier Engine: 6 cylinder turbocharged diesel 250 hp at 2200 rpm 1.Spin on type filters 2.Two stage air cleaner 3.24 volt 70 amp alternator 4.

a.

Carrier Transmission & Clutch: 6 speed automatic transmission 1.

b.

Carrier Transfer Case: 1 to 1 transfer case 1.Front axle disconnect 2.

c.

Carrier Cab: One person cab 1.Air ride seat 2.Heater, air condition, and defroster 3.2 speed windshield wipers 4.Tinted glass 5.Isolated and acoustic lined 6.Gauges to monitor engine functions 7.

d.

Frame: Sized for GVW and stress of mounted upper structure 1.Bolt on front bumper 2.Desiccant type, spin on type, air dryer 3.Fuel tank 50 gallon minimum 4.

e.

Safety: Electric horn 1.West coast mirrors with convex spot mirrors 2.Tow hooks 3.Fire extinguisher 4.Backup alarm 5.

f.

Front Axle: 16,000 front drive axle 1.Leaf spring suspension 2.16.5x5 "S" cam brakes 3.Automatic slack adjuster 4.Integral power steering 5.Hydraulic axle lockouts 6.425/65R22.5 on/off road tires 7.

g.

Rear Axle: Tandem axles 40,000 lb. rated 1.Hendrickson rear suspension 2.16.5x7 "S" cam brakes 3.Automatic slack adjusters 4.11R 24.5 traction type tires 5.

h.

UPPER STRUCTURE:3.

Hydraulic System: 80 HP drive motor 1.44 HP swing motor 2.

a.

Automatic swing park brake 3.50 gallon oil reservoir 4.Spin on hydraulic filters 5.Swing speed 8 RPM 6.

Hydraulic Remote Control: Travel and steering controls in upper structure cab 1.Automatic brakes and axle lockouts 2.Movement alarm 3.

b.

Upper Structure Cab: Isolated and acoustic lined 1.Tinted safety glass 2.Adjustable operators seat 3.Heater, air condition, and defroster 4.Work lights 5.Wipers and washers 6.Mirrors on left and right 7.Skylight 8.

c.

Upper Structure Control: Electronic joysticks on adjustable pedestals 1.Engine monitoring lights or gauge with audible warning or automatic shutdown 2.Pedals for steering and travel 3.Low/high travel switch 4.Electric horn 5.Engine speed control 6.

d.

Bucket: Quick attach type 1.60" ditching bucket provided with machine 2.

e.

Boom: Telescopic boom 1.180 degree boom rotation 2.30' reach at round level from upper structure pivot to bucket cutting edge 3.

f.


SPECIFICATION #48 - COMPACTION VIBRATORY ROLLER (SINGLE DRUM) 30,000 LB2019 Bomag BW177D-52019 Case SV2082019 Caterpillar CS442019 Sakai SV5402019 Volvo SD-75B


WEIGHT:1.

Minimum operating weight with open rops 15,200 lbs.a.

DRUM/VIBRATORY SYSTEM:2.

Maximum compaction shall not be less than 30,000 lbs.a.Drum shall have a compaction width of not less than 66"b.Drum shall be smooth and not be less than 48" in diameterc.Vibratory system shall be hydraulically driven and have two amplitude settingsd.Drum shall be equipped with an adjustable cleaning devicee.Drum and vibratory pack shall be isolated from the machine during normal operationf.

ENGINE/CAB:3.

Turbocharged diesel engine, minimum 74 HPa.Operator station shall be mounted to the frame with rubber mounts to further isolate the operation and controls from machinevibration during operation

b.

Guages or warning indicators for fuel level, engine oil, hydraulic oil and coolant temperature with an alert sounding device activedwhenever a warning indicator is illuminated.

c.

A backup alarm shall emit an audible alarm whenever the propel lever is moved into reversed.

TRAVEL SYSTEM:4.

A machine must be hydrostatic driven for the rear axle and the drum drive motora.


12 or 24 volt electric systema.Maintenance free battery suppling 750 cold cranking ampsb.Wiring harness protected with nylon-braided wrapc.


SPECIFICATION #49 - 47" SMALL DOUBLE DRUM ROLLER 5,400 LB2019 Bomag BW120SL-52019 Case DV262019 Caterpillar CB24B2019 Dynapac CC12002019 Volvo DD25B


WEIGHT:1.

Minimum operating weight 5,423 lbs.a.


Drum compactor width on both drums no less than 47"a.Drum shall be smooth and not less than 27.5" in diameterb.Vibratory system shall be hydraulically drivenc.Drum shall be equipped with scrapers both front and rear of both drumsd.Drum shall be hydraulically driven and have two amplitude settingse.

ENGINE:3.

Diesel engine of not less than 25 HPa.Reverse alarm for reverse operationsb.

TRAVEL SYSTEM:4.

The machine shall be hydrostatlically drivena.Steering shall be centered articulated and oscillatedb.

MISCELLANEOUS:5.

Unit shall be equipped with a pressurized water system for both drumsa.Electrical system shall be 12 or 24 Voltb.


SPECIFICATION #50 - 70" LARGE DOUBLE DRUM ROLLER - 22,000 LB2019 Bomag BW190AD-52019 Case SV216D2019 Caterpillar CB132019 Sakai SW8802019 Volvo DD120C


WEIGHT:1.

Minimum operating weight 22,000 lbsa.


Drum compaction width on both drums no less than 70"a.Drum shall be smooth and not less than 48" in diameterb.Vibratory system shall be hydraulically drivenc.Drum shall be equipped with scrapers both front and rear of both drumsd.Drum shall be hydraulically driven and have two (2) amplitude settingse.

ENGINE:3.

Diesel engine of not less than 100 HPa.Reverse alarm for reverse operationsb.

TRAVEL SYSTEM:4.

The machine shall be hydrostatically drivena.Steering shall be center articulated and oscillatedb.

MISCELLANEOUS:5.

Unit shall be equipped with pressurized water for both drumsa.Electrical system shall be 12 or 24 voltb.


SPECIFICATION #51 - TRAILER MOUNTED SEWER CLEANER2019 Obrien 7018-SC2019 Sewer Equipment Co. of America 747-FR20002019 Vac-Con VecJet VJ7002019 Vactor RamJet 4018


ENGINE1.

60 h.p. diesel enginea.Water cooledb.Engine enclosurec.15 gal. fuel tankd.

HIGH PRESSURE WATER PUMP2.

4000 psi at 18 gpma.Pressure relief valveb.Triplex type pumpc.Low water shutdownd.Multi-flow type system [ pressure change without changes to engine rpm ]e.

CONTROLS3.

Located next to hose reela.Ignitionb.Throttlec.Gauge package [tachometer, hourmeter, oil pressure, volts, and low oil / high temp shutdown]d.Water control valvee.

WATER TANK4.

700 gal capacitya.High density polyethylene with bafflesb.Sight gaugec.2 1/2" overhead tank fill , anti siphon , air gap typed.Strainere.Tank drainf.

HOSE REEL5.

800 ' capacity of 1/2" high pressure sewer hosea.Hydraulic power in and outb.

HOSE REEL DRIVE HYDRAULIC SYSTEM6.

Hydraulic pump 8 gpma.15 gal hydraulic reservoirb.Spin on type hydraulic filterc.

TRAILER7.

12000 lb gvwa.6" x 3/16" frameb.Tandem axlec.2 5/16" hitchd.Tongue jacke.235 / 80 r 16" tiresf.Fendersg.Breakaway switchh.Lighting as required by Federal and State lawsi.Reflective stripingj.Toolbox with locking systemk.LED directional arrowstickl.Warning beacon [tank mounted]m.

EQUIPMENT FURNISHED8.

500' of 1/2 " high pressure sewer hose a.100' of 1/4" hose and nozzle for small pipe b.Washdown gun and 25 ' of hose with quick dissconnects c.Tiger tail hose protecter d.Nozzles to be furnished, 15 degree, 35 degree, chisel point, grenade flushing type, skid assembly, and rotater nozzle e.


SPECIFICATION #52 - VACUUM EXCAVATOR, TRAILER MOUNTED - 14,000 LB GVWR2019 PacificTek PV8002019 RamVac 1000 Vacuum Excavator2019 Vac-Con Mudslinger MS8002019 Vermeer LP873SDT2019 X-Vac X800


WEIGHT:1.

6,190 lbs. (without trailer)a.

ENGINE:2.

36 hp diesel enginea.Water cooledb.Fully enclosed sound attenuated engine enclosure (including vacuum pump and high pressure water pump)c.15 gallon fuel tankd.

VACUUM PUMP:3.

580 CFM at 15 inches of mercurya.Mounted inside engine enclosureb.Washable filtration cylindersc.Reverse pressure (to clear hose and offload liquids)d.

HIGH PRESSURE WATER SYSTEM:4.

400 PSI at 4 GPM water pumpa.Low water automatic shutdownb.Two 100 gallon poly water tanksc.50' high pressure water hose on hose reeld.5' and 3' wand and control handlee.

CONTROLS:5.

Lockable and waterproofa.Curbside locatedb.Oil pressure, water temperature, fuel and vacuum gaugec.Electronic throttled.

TANK:6.

Full open rear doora.Door hydraulically openedb.Twin dump cylindersc.6" stainless steel portal shutoffd.800 gallon debris tank capacitye.

BOOM:7.

4" pickup hosea.Hydraulically powered in/out and up/downb.Boom cradlec.360 degree movementd.2 dielictric 3" suction wandse.33' rubber suction hosef.

TRAILER:8.

7,000 lb. dexter torsion anxlesa.14,000 lb. GVWRb.10,000 lb. jack standc.I beam constructiond.Pintle hitche.Electric brakes with safety breakawayf.LT235/85R16 tiresg.Stop/tail/turn lightsh.


SPECIFICATION #53 - 10 CU YD COMBINATION SEWER CLEANING/VACUUMINGMACHINE

2019 Aquatech B-102019 Sewer Equipment Co. of America 900-ECO-12YD Combo2019 Super Products Camel Maxxx2019 Vacall AJV 10102019 Vac-Con 11 Yard2019 Vactor 2100I Plus

NOTE TO PURCHASERS: This is an INCOMPLETE UNIT. This is a bid award on a combinationSewer Cleaning/Vacuum Unit to be mounted on an appropriate sized cab & chassistruck. Agencies purchasing this unit will need to provide a cab & chassis truck ofappropriate size, GVW, and, options necessary to have the selected combination SewerCleaner/Vacuuming Unit to be mounted on, or have the truck provider assist inordering the correctly outfitted truck. Listed above you will find the model numbersof the units that will be included in the years contract. All items factoryinstalled unless otherwise noted.

AIR/VACUUM SYSTEM:1.

Positive displacement vacuum pump or centrifugal compressora.3500 CFM @ 14.5 inches of mercury, minimumb.Mufflerc.Vacuum relief valvesd.Centrifugal separator with clean oute.PTO or hydrostatic drivef.

DEBRIS TANK:2.

10 cu. yard capacitya.45 degree hydraulic dumpb.Top hingedc.Hydraulic door locksd.Sight glass or indicatore.Drain valve with hosef.Check ball system or vacuum breakerg.

BOOM ASSEMBLY:3.

270 degree boom working areaa.Hydraulic up/downb.Clean out portc.Transport cradled.8" boom hosee.Pendant controlf.

WATER PUMP:4.

2500 PSI, 80 GPMa.Pressure relief valveb.Wash down gun with relief valvec.

WATER TANK:5.

1000 gallon capacitya.Curb side fillb.Level indicatorsc.

HOSE REEL:6.

800' of 1" hose capacitya.400' of 1", 2500 PSI hose suppliedb.Power in/outc.Reel speed control systemd.Position lock systeme.Engine and hose reel controlsf.Level windg.

DRIVE SYSTEM:7.

DRIVE SYSTEM:7.

Hydrostatic transfer case, split PTO, or auxiliary engine or transfer case a.

MISCELLANEOUS:8.

Nozzles 15 degree and 30 degree for jet a.Wash down gun b.8" intake tube 20' minimum c.Flexible hose guide d.Hose storage rack e.


SPECIFICATION #54 - 3 WHEEL MECHANICAL OR REGENERATIVE AIR SWEEPER2019 Elgin Pelican2019 Global M3 Regenerative Air Sweeper2019 Global R3 3 Wheel Regenerative Air Sweeper


ENGINE:1.

4 cylinder diesel engine 74 HP minimum.a.120 AMP alternatorb.Fuel water separatorc.30 gallon fuel tank capacityd.

TRANSMISSION:2.

Hydrostatic drive typea.35 gallon reservoirb.Capable of 20 MPH minimumc.

CAB:3.

Sealed type cab with filtered intake.a.Tilt and telescoping steering columnb.Tinted glassc.Sound suppressedd.Intermittent windshield wipers with washere.Full gauge and warning lights for engine monitoringf.Climate controlled cab, heater, defroster and air conditionedg.If cab is not center mounted, it must have dual controls for operating on either right or left hand side.h.

FRAME:4.

116" wheelbasea.Rail type channel frameb.

SAFETY ITEMS:5.

Dual west coast mirrors with spot mirrorsa.Headlights, turn, brake and hazard lightsb.Worklights for gutter broomsc.Cab mounted warning strobe light with protective caged.Backup alarme.Rearview backup cameraf.

BRAKES/STEERING:6.

Hydraulic power assisted service bakesa.Parking brakeb.Turning radius 15' maximumc.

DEBRIS HOPPER:7.

3.5 yard capacity minimuma.9'6" minimum dump heightb.

CONVEYOR:8.

Rubber belt type with flightsa.Hydraulic driveb.

MAIN BROOM:9.

32" diameter minimuma.56" width tube typeb.Hydraulic drivec.

GUTTER BROOMS:10.

Right & left side brooms to have adjustable down pressure located in cab.a.

36" diameter minimum b.Segmented type broom c.Hydraulic drive d.

WATER SPRAY SYSTEM:11.

220 gallon water tank a.Run dry type water pump b.15' hydrant fill hose c.Water spray jets adjacent to all brooms d.Water filter e.

PICK UP HEAD12.

The following requirements are for the regenerative air system type sweeper. All other requirements are the same for eithermachine

1.

72" outside dimension a.12" pressure hose b.12" suction hose c.Spring type suspension d.

BLOWER13.

The following requirements are for the regenerative air system type sweeper. All other requirements are the same for eithermachine

1.

Direct hydraulic drive a.Cast aluminum with abrasion resistant coating b.Blower housing rubber lined c.


SPECIFICATION #55 - CABOVER MECHANICAL BROOM STREET SWEEPER2019 Elgin Eagle2019 Johnston ES3512019 Schwarze M6 Avalanche


CAB & CHASSIS:1.

Engine: 6 cylinder diesel 200 HP minimum 1.

a.

Transmission: Automatic transmission to meet the correct engine size and GVW of vehicle. Hydrostatic drive is acceptable. 1.

b.

Engine Equipment: Alternator - 12V / 130 AMP 1.Fuel water separator 2.Fuel tank – 50 gallon 3.

c.

Cab: Dual operating position type cab to include: Steering, controls, etc for sweeping from either side. 1.Rubber floor mats 2.Air ride seating 3.Pressurized cab with heat and air conditioning 4.Instrumentation for truck - oil pressure, water temperatures, voltmeter gauges 5.Instrumentation for sweeper-tachometer, hour meter, oil pressure, coolant temperature gauges 6.

d.

Frame: Rail type 80,000 psi 1.Size – 10.9" x 3.5" x .34" 2.Frame overhang 3.Wheelbase 130" minimum 4.Front steel bumper 5.

e.

Safety: Dual West Coast bright finish heated mirrors with LH & RH remote 1.Intermittent windshield wipers 2.Daytime running lights 3.Backup alarm 4.Auto shutdown 5.

f.

Axles: Front axle: 11,900 lb. GVW 1.Rear axle: 21,000 lb. GVW 2.Single speed rear axle 3.22.5 x 8.25 steel wheels - disc type 4.11R x 22.5 14-ply radial tires 5.

g.

Brakes: Antilock brakes 1.Front air brakes - 15 x 4 drum 2.Rear air brakes 16.5 x 7 drum 3.Automatic slack adjusters - front and rear 4.Air dryer - frame mounted 5.

h.

MOUNTED SWEEPER BODY (STANDARD EQUIPMENT):2.

Engine: 4 cylinder diesel - 47 horsepower, governed at 2800 RPM 1.Spin-on oil filter 2.Alternator – 12V / 60AMP 3.

a.

Side Brooms: Right & left side gutter brooms (tilt control in cab) 1.Hydraulically raised & lowered 2.42" diameter – segment type 3.Adjustable down pressure (Manual) – optional down pressure pump 4.

b.

Main Broom: Length - 58" minimum 1.Diameter - 35" minimum 2.Hydraulic motor - direct or chain drive and reversible 3.Full floating trailing arms w/shocks 4.Lift Control – inside cab 5.

c.

Sweeper Body: Overall height – 10' with strobe 1.Lift capacity – 11,000 lbs minimum 2.4.5 cubic yard hopper 3.Dump height - 10' minimum 4.Lift design – hydraulic 2-stage scissors 5.Hopper inspection door 6.Work lights – 1 on each gutter broom and one in rear 7.

d.

Hydraulic System: Hydraulic pump capacity minimum – 24gpm@2600rpm 1.Pump: dual tandem gear 2.Reservoir – 21 gallons 3.Spin-on 10 micron hydraulic pump 4.Externally mounted reservoir level indicator 5.

e.

Water Spray System: Water tank construction – polyethylene and removable 1.Water tank capacity - 280 gallons minimum 2.Fill hose 2 1/2" x 16' with NST coupler 3.Diaphragm pump type with run dry capability 4.Pump capacity – 3.0 GPM minimum 5.Minimum of 9 spray nozzles – 2 min per gutter broom, 3 min for main broom 6.Water filter – 80 micron mesh cleanable 7.

f.

Conveyor/Elevator System: Minimum of 9 flights – replaceable 1.Belt material – rubber reinforced fabric 2.Belt speed – variable with auxiliary engine RPM 3.Drive – reversible with direct drive 4.Elevator jam warning light & buzzer in cab 5.Conveyer flush – built in 6.

g.


SPECIFICATION #56 - COMPACT SWEEPER - 2.3 CU YD AIR SWEEPER2019 Johnston C2012019 Nitehawk Municipal Raptor II


OPERATING WEIGHT:1.

8800 LBS. GVWR a.Empty weight-5900 LBS b.

ENGINE/TRANSMISSION:2.

78 hp a.Hydrostatic drive b.

BRAKES/TIRES3.

Drum type brakes [ power assist] a.Front tire size 6.50 R10 Radial b.Rear tire size 225/75 R10 Radial c.

SWEEPER DIMENSIONS:4.

Height: 72" a.Width: 52" b.Length: 162" c.

HOPPER:5.

2.3 cubic yard capacity a.

GUTTER BROOMS:6.

Equipped with left and right side gutter brooms a.Front mounted 33.5" diameter b.Overall sweeping width 122" c.

WATER SYSTEM7.

66 gal recirculation water system capacity a.40 gal clean water system capacity b.

LIGHTING / SAFETY8.

Lighting package to enable vehicle to operate on the road a.Work lights for operation of vehicle at night b.Amber warning beacon c.Intermittent wipers d.

COMFORT ITEMS:9.

Cab to be air conditioned and heated a.Suspension type operator seat b.

INSTRUMENTATION:10.

Full instrumentation to monitor operation of vehicle a.

FAN UNIT:11.

Centrifugal type fan a.Wear resistant blades b.


SPECIFICATION #57 - REGENERATIVE AIR STREET SWEEPER2019 Elgin Crosswind (J Plus)2019 Johnston RT6552019 Schwarze A7 Tornado2019 Tymco 600


CAB & CHASSIS:1.

Engine: 6 cylinder diesel, 200 HP minimum. 1.

a.

Transmission: Allison 2000 series, 5-speed automatic 1.

b.

Engine Equipment: Alternator: 12 volt 100 amp 1.Fuel water separator 2.Spin-on filters 3.

c.

Cab: Cab over, steel cab, with rust preventative coating 1.Dual operating position type cab to include: steering, controls, etc for sweeping from either side 2.Rubber floor mats 3.Air ride suspension seats, both sides 4.Pressurized cab with heat and air conditioning 5.Instrumentation for truck - oil pressure, water temperature, voltmeter gauges 6.Instrumentation for sweeper – tachometer, houmeter, oil pressure, coolant temperature gauges 7.

d.

Frame: Rail type 80,000 psi 12.69 section modulus 1.Wheelbase - 152" minimum 2.Front steel bumper 3.Fuel tank - 50 gallon 4.

e.

Safety: West coast mirrors with lower mounted convex mirrors. 1.Intermittent windshield wipers 2.Daytime running lights 3.Backup alarm 4.Auto shutdown system for sweeper power plant 5.

f.

Axles: Front axle: 11,900 lb. GVW 1.Rear axle: 21,000 lb. GVW 2.Single-speed rear axle 3.22.5 x 8.25 steel wheels - disc type 4.11R x 22.5 14 ply tires 5.

g.

Brakes: Antilock brakes 1.Front - 15 x 4 drum 2.Rear - 16.5 x 7 drum 3.Automatic slack adjusters - front and rear 4.Air dryer 5.

h.

MOUNTED SWEEPER BODY:2.

Engine: 4 cylinder turbocharged diesel 99 HP minimum 1.Spin-on oil filter 2.Dual element air cleaner 3.Alternator - 12 volt 65 amp minimum 4.

a.

Blower: Direct belt drive 1.Blower rating - 20,000 cfm 2.

b.

Blower housing construction of abrasion resistant steel 3.Blower housing rubber lined 4.

Pickup Head: 90" OD 1.Hose size – 14" pressure, 12" suction 2.Hydraulically raised and lowered 3.

c.

Side Brooms: Right and left side gutter brooms 1.Hydraulically raised and lowered 2.42" diameter - segment type 3.Adjustable downward pressure 4.

d.

Sweeper Body: 7 yd. volume metric capacity 1.50 degree dump angle or raker bar 2.Centrifical dust separator 3.Hopper dump door to hydraulically open/close, lock and unlock 4.Hopper screen - hinged, quick release 5.

e.

Hydraulic System: Hydraulic pump capacity - 7.7 gpm at 2500 rpm 1.Direct drive hydraulic pump 2.Reservoir - 23 gal. 3.Spin-on 10 micron hydraulic filter 4.

f.

Water Spray Dust Control System: Water tank construction - polyethylene 1.220 gallon capacity 2.Fill hose - 16' long 3.Diaphragm pump type with run dry capability 4.Pump capacity - 5 gpm 5.Pump pressure - 25 psi 6.7 spray nozzles, 4" pickup head, 1" suction tube - 2 on each side of broom 7.Filter - 80 mesh cleanable 8.

g.


SPECIFICATION #58 - SELF PROPELLED HYDROSTATIC BROOM - CENTER SLUNG2019 Blaw-Knox CB-952019 Broce 350 Broom


WEIGHT:1.


ENGINE:2.

Diesel engine 74 HP at 2200 RPM a.Pre-cleaner 54 klone or equivalent b.27 gallon fuel tank c.

TRAVEL SYSTEM:3.

2 speed hydrostatic drive a.High speed travel, 20 MPH b.225/75R15 tire size c.Joystick direction controls, or foot pedal d.Front or rear wheel steering e.

CAB:4.

Roll over and falling object protective structures a.Enclosed cab with air conditioner, heater and defroster fan b.Front windshield wiper c.Gauges or warning indicators for fuel level, engine oil, hydraulic oil and coolant d.Right and left side doors e.Right and left side mirrors f.Shall have safety lighting package and night operating lighting package g.

BROOM:5.

Minimum 7'6" poly or poly-steel brush a.Brush shall have quick charge core system b.Minimum 150 gallon brush watering attachment c.Shall have variable brush down-pressure control d.Brush shall be hydraulically driven e.


SPECIFICATION #59 - 7' X 16' ENCLOSED CARGO TRAILER – 7,000 LB GVWR2019 Pace American CS7X16TE22019 United U-716TA35-8.52019 Wells Cargo CW1622-102


DIMENSIONS:1.

Width - 7' a.Length - 16' b.GVWR - 7,000 lb. c.

FRAME:2.

Tubular steel main rails a.C-channel crossmembers b.Formed steel corner posts c.Steel roof bows d.Formed angle top and bottom sills e.Vertical sidewall posts on 16" centers f.Non-corrosive fasteners g.All exposed steel primed and painted h.3 piece A frame i.Positive lock ball coupler j.Tongue jack k.Safety chains - DOT rated l.

FLOOR/WALLS/ROOF:3.

3/4" exterior grade plywood floor a.1/4" plywood interior liner b..030" prefinished aluminum exterior, state colors c.Smooth galvanized steel or one piece aluminum roof d.Fiberglass front cap e.Extruded aluminum bottom trim f.Extruded aluminum roof cove with drip rail g.Double locking door on rear h.

AXLES:4.

Tandem 3,500 lb. torflex axles a.15" wheels b.205 x 15 trailer rated tires c.Electric brakes with breakaway switch d.

LIGHTING SYSTEM:5.

Protected turn/stop/tail lights a.Clearance lights b.Wiring run in conduit c.Heavy duty trailer plug d.

MISCELLANEOUS:6.

Spare wheel and tire a.


SPECIFICATION #60 - 8'6 X 25' DECK OVER FLATBED TRAILER- 16,000 LB GVWR2019 Big Tex 22PH2552019 Eager Beaver B8-DOW2019 Econoline BP0821DE Deckover Dovetail2019 Felling Trailers FT-16-22019 Interstate 16BST2019 Texas Trailer TX85258T2019 Towmaster TC-162019 Trail King TK202019 XL Specialized Trailers XL 24 T


DIMENSIONS:1.

Deck width - 8'6" a.Overall deck length - 25' b.Dovetail length - 5' c.GVWR - 16,000 lb. d.

FRAME:2.

5" channel side rails a.3" channel cross members on 16" centers b.4" channel undercarriage c.2" x 3/8" rub rail with stake pockets d.Pintle hitch e.

DECK:3.

2 x 8 pressure treated deck a.Galvanized deck screws b.5' dovetail c.Spring assist stand up ramps d.

AXLES:4.

Tandem 8,000 lb. Dexter oil bath axles (2) a.Electric brakes b.Breakaway brake system with well cell battery c.

LIGHTING SYSTEM:5.

Protected turn/stop/tail lights a.Wiring run in conduit b.Heavy duty trailer plug c.

MISCELLANEOUS:6.

Spare tire and rack a.Lockable tool box b.Primed and painted - choice of color c.Tongue jack rated for GVWR of trailer d.


SPECIFICATION #61 - PULL BEHIND DUMP TRAILER - 14,000 LB GVWR 2019 Big Tex 14LX2019 Econoline LB0714HE Dump Trailer - Discontinued Jan 20192019 Felling FT-12DT-HD


GVWR:1.

14,000 lbs.a.

BED:2.

Grease on all hingesa.Self storing rampsb.D ring tie dowsc.

BED SIZE & FRAME:3.

6'8" widea.14' lengthb.24" deck heightc.Tube steel boxd.10GA bed floore.Rear stabilizersf.12,000 lb. tongue jackg.20" high sides and tailgate, minimumh.

BED LIFT:4.

Scissor type hydraulic lifta.12 volt power unit with batteryb.15' pendant controlc.

AXLES:5.

Dexter easy lube or equivalenta.Sized for GVWR of trailerb.4 wheel electric brakes with breakawayc.

MISCELLANEOUS:6.

Conspicuity type on sidesa.Tail/stop/turn lightsb.7 way trailer plugc.Tarp systemd.Spare tiree.Pintle type hitch or ball (customer selected)f.

agrissom

Highlight


SPECIFICATION #62 - 48' WASTE TRAILER WITH WALKING FLOOR2019 East Manufacturing Unloader Live Floor2019 Mac Trailer TNSP48MF2019 Steco AW0481022019 Warren WMFT


DIMENSIONS:1.

Length - 48' aluminum a.Width - 102" b.Side height - 100" c.

FLOOR:2.

Keith or Hallco running floor a.Extreme duty slats with center rib b.

CROSSMEMBERS:3.

14" spacing a.

CROSSTUBES:4.

Center and rear crosstubes a.Bolt in style b.

LIGHTS:5.

LED lights a.Mid turn lights b.

TARP:6.

Manual roll type - side to side a.Mesh type tarp b.

TAILGATE:7.

Side swing - left or right a.CAM locking system with safety chain b.Extreme duty hinges c.

LANDING GEAR:8.

Holland Mark V a.

AXLES:9.

TP axles or equivalent a.Same inner and outer bearings b.Outboard mount hubs c.

SUSPENSION:10.

Cast hangers a.Leaf springs b.

TIRES AND WHEELS:11.

Steel Disc 22.5x8.25 a.11R22.5 radial tires b.

MISCELLANEOUS:12.

Tow hooks on rear a.Air deflector in front b.


SPECIFICATION #63 - HYDRAULIC TAIL TRAILER - 70,000 LB2019 Felling Trailers FT-70-2-PL-HT2019 Pitts HD35 2019 XL Specialized Trailers XL 80PT


DIMENSIONS1.

Deck width – 8'6" a.Overall length – 48' b.Deck length – 25' c.Hydraulic tail – 12' (8' with 4' fold under) d.GVWR – 70,000 LBS e.

FRAME2.

Cambered "I" beam main frame a.49" Kingpin height b.16" Kingpin setting c.82" Swing clearance d.8' Upper deck length e.

DECK3.

1 ½" Apitone or oak decking a.¼" Floor plate over wheels b.Traction plate on hydraulic tail c.

HYDRAULIC TAIL4.

8' Main tail a.4' Fold under tail b.Hydraulic actuated with tail lock c.14 degree load angle d.

LANDING GEAR5.

Pin drop type or 2 speed type a.

AXLES/SUSPENSION/TIRES6.

2 – 22,500 LB axles a.Oil seal hubs b.6.5 x 17.5 steel wheels c.235/75R x 17.5 radial tires d.Air brakes with automatic slack adjustors e.ABS brake system f.Air ride suspension with auto and manual controls g.

LIGHTING7.

LED lighting a.Wiring in conduit b.Mid turn signals c.Lighting as per DOT regulations d.

MISCELLANEOUS EQUIPMENT8.

12.000 LB hydraulic winch mounted on upper deck over kingpin. Wireless control. a.Toolbox on upper deck b.Hydraulic tail controls both sides c.Air ride controls with dump valve d.


SPECIFICATION #64 - ARTICULATED OFF ROAD DUMP TRUCK - 50,000 LB PAYLOADCAPACITY

2019 Bell B25E2019 Caterpillar 7252019 John Deere 260E2019 Terex TA3002019 Volvo A25G


WEIGHT:1.

Minimum operating weight - 40,000 lbs. a.Minimum gross weight (with payload) - 91,000 lbs. b.

ENGINE:2.

Turbocharged diesel engine, 265 hp 6 cylinder, 549 cubic inch minimum. a.Spin on type filters. b.Two stage air cleaner. c.

TRANSMISSION:3.

6 speeds forward, 1 speed reverse. a.Top speed of 31 mph b.Hydraulic retarder c.

BRAKES:4.

Disc type service brakes. a.Disc type parking brake. b.

AXLES & DIFFERENTIALS:5.

Differential locks a.Planetary gear reduction final drives. b.Inter axle differential lock. c.

TIRES:6.

Tubeless, radial off road hauler tires. a.23.5 R 25 tire size b.

STEERING:7.

45 degree left or right articulation angle. a.Secondary electric steering system for emergency steering. b.Double acting steering cylinders. c.


Cab to be pressurized, heated, air conditioned and filtered. a.Built in ROPS/FOPS protection. b.Suspension type operators seat with seat belt. c.Cab instrumentation or engine monitoring system with audible alarms. d.Tinted glass windows. e.Sun visor f.Front and rear intermittent windshield wipers. g.Work lights, headlights, stop, tail and turn signal lights. h.Left and right mirrors. i.

BODY:9.

Dump body tipping angle 70 degrees. a.Mud flaps b.Two single stage double acting body hoist cylinders. c.18 yd. heaped capacity d.Body rise time maximum 12 seconds. e.

MISCELLANEOUS:10.

MISCELLANEOUS:10.

95 gallon fuel tank minimum. a.Guard or shielding package. b.


SPECIFICATION #65 - 80,000 LB LANDFILL COMPACTOR2019 Bomag BC772RB-42019 Caterpillar 8262019 Tana E380 Compactor2019 Volvo LC450H Compactor


WEIGHT:1.

Minimum operating weight - 80,000 lbs. a.

ENGINE:2.

Turbocharged diesel engine 400 hp minimum. a.Spin on type filters b.

TRANSMISSION/HYDRAULIC SYSTEM:3.

Mechanical or hydrostatic drive will be acceptable. a.2 speeds forward and 2 speeds reverse, minimum. b.Spin on type hydraulic filters. c.


Enclosed, sound suppressed cab. a.Air filtration system b.Air conditioned, heater and defroster. c.Gauges and engine monitoring shutdown system. d.Adjustable suspension seat. e.Outside mirrors f.Work lights g.Windshield wipers and washer h.


24 volt a.

WHEELS:6.

Compaction wheels - 48" width minimum. a.Wheel diameter - 58" width minimum. b.Chevron chopper blades, weld-on or pin-on teeth type wheels acceptable. c.Anti wire wrapping device, if applicable. d.Cleaner bars, if applicable. e.

BLADE:7.

Straight or U type trash blade acceptable. a.14' blade minimum b.6' blade height minimum c.Full width trash screen on top of blade. d.Bolt on cutting edges. e.

MISCELLANEOUS:8.

Fully shielded engine compartment. a.Removable belly pan b.Landfill shielding package, if applicable. c.


SPECIFICATION #66 - MOBILE SHREDDER - TRAILER MOUNTED2019 Tana Shark 440D Shredder


Weight: 27,000 kg a.Length: 15 740mm b.Width: 2 520mm c.Material feeding height : 3 395mm d.Belt discharge height: 4 030mm e.

ENGINE2.

Diesel, 540 hp @ 2100 rpm a.Turbocharged w/ intercooler b.750 li fuel tank c.

POWERTRAIN3.

Hydro-static drive w/ auto speed control a.Variable displacement drive motors b.Axial piston pumps, variable displacement c.

ROTOR4.

Rotor diameter 920mm a.Rotor 30 max rpm b.Rotor shredding length 3000 mm c.Rotor knives 33, reversible type d.Counter knives 23 e.Adjustable rotor screen f.

CONTROLS5.

Gauge package, w engine protection shutdown a.Shredder control unit to protect from overloading, overheating and damage of the powertrain b.

CONVEYOR6.

Hydraulic driven conveyor a.Raised and lowered by hydraulics b.

TRAILER7.

Trailer to be constructed and sized for the installed unit, and will meet all local, state, and federal laws for use on highway. a.Hydraulic support legs b.


SPECIFICATION #67 - BRUSH CHIPPER - TRAILER MOUNTED2019 Bandit 15XP2019 DuraTech TC-152019 Morbark M15R2019 Vermeer BC1500


DIMENSIONS:1.

Weight - 6800 lbs. a.Width - 72" b.Height - 100" c.Length - 176" d.15" chipping capacity e.

ENGINE:2.

122 hp diesel engine a.Over center type clutch b.Heavy duty air cleaner c.Spin on type filters d.

CHASSIS:3.

Main frame constructed of rectangular tubing or "z" section. a.7000 lb. axle torsion type b.Electric brakes with breakaway switch c.ST 235/80R16 tires load range E d.Steel wheels e.Drop leg jack f.2 1/2" diameter lunette or 2 5/16" ball hitch g.Adjustable height hitch h.Safety chains i.6 way light connector j.All wiring in conduit to lights k.Four function rear lights l.

FEED SYSTEM:4.

Infeed throat opening - 20" x 15" a.Serrated infeed rollers b.Feed rollers hydraulically driven c.Feed table height - 27" d.Feed table length - 30" e.Safety control bar a round infeed opening for emergency stop. f.

CHIPPER DRUM OR DISC5.

Drum type: Size - 22" diameter x 22" width 1.2 knife pockets 180 degrees apart 2.Dual edge reversible knives 3.Extreme duty bearings 4.Adjustable bedknife (reversible) 5.

a.

Disc type: 37" x 2" diameter disc 1.4 knives reversible 2.

b.

CHIPPER HOUSING:6.

Easy access door for knife changes a.Drop down door for anvil adjustment or clean out b.Chipper housing to be constructed for maximum safety and operator protection c.

DISCHARGE CHUTE:7.

Rotation of 360 degrees a.

Adjustable chip deflector b.Locking pin for chute rotation c.

MISCELLANEOUS:8.

26 gallon fuel tank a.Engine shutdown system b.Locking tool box c.Vandalism protection d.


SPECIFICATION #68 - SELF PROPELLED STUMP CUTTER2019 Bandit 25502019 Vermeer SC3622019 Toro STX 38EFI


ENGINE:1.

35 H.P. gasoline engine a.6 gallon fuel tank b.Positive feed oil system with spin on filter c.heavy duty air filter d.12 volt starting/charging system e.

GROUND DRIVE:2.

Hydraulic Ground Drive a.2 speed travel b.Hydraulic brake system c.Hydraulic steering system d.Hydraulic system spin on filter e.4 gallon hydraulic reservoir f.

CUTTER DRIVE:3.

Electric drive clutch a.Adjustable V belt drive b.

CUTTER WHEEL:4.

17" diameter a.16 dual cutting edge teeth b.Teeth pocket mounted c.Cutter wheel guard d.

CONTROLS:5.

Hourmeter a.Low-oil shutdown b.Boom swing left and right c.Boom up and down d.Travel forward and reverse e.Steering f.Operator presence shutdown g.

APPROXIMATE DIMENSIONS:6.

Weight - 1320lbs a.Length - 110" b.Width - 49" c.Height - 53" d.

CUTTING DIMENSIONS:7.

Above ground - 24" a.Below ground - 15" b.


SPECIFICATION #69 - WALK BEHIND TRENCHER2019 Vermeer RTX250


ENGINE:1.

25 H.P. gasoline engine a.7 gallon fuel tank b.Positive feed oil system with spin on filter c.12 volt starting/charging system d.

GROUND DRIVE:2.

Hydrostatic a.Rubber ground tracks b.7" track width c.31" track length on ground d.

TRENCHER DRIVE:3.

Hydraulic drive a.8 gallon hydraulic reservoir b.Hydraulic system spin on filter c.

TRENCHER BOOM:4.

Digging depth - 48" a.Auger diameter - 18" b.Cutting width minimum - 4" c.

CONTROLS:5.

Operator presence safety system a.Low-oil shutdown system b.Steering control c.Operator presence safety system d.Low-oil shutdown system e.Steering control f.Trencher controls g.Travel control h.Boom controls i.

APPROXIMATE DIMENSIONS:6.

Weight - 1550 LBS. a.Length - 79" b.Width - 34" c.Height - 48" d.


SPECIFICATION #70 - AIR COMPRESSOR, TRAILER MOUNTED2019 Doosan P185WDO-T4F2019 Ingersoll Rand 2475F13GH2019 Ingersoll Rand 2475F14G2019 SULLAIR 185 T4F2019 Sullivan Palatek D185PDZ


Weight: 1950 lbs. a.Length: 79 Inches b.Width: 40 Inches c.Height: 47 Inches d.

ENGINE2.

49 hp Tier 4 Engine a.12 Volt electrical system b.Engine protection system c.Gauge package d.

COMPRESSOR 3.

185 cfm @ 100 psi a.Rotary or reciprocating style compressor b.2 service valves c.

TRAILER 4.

3700 GVW axle rating a.Manufacturer Rated Tires b.Fold up tongue jack c.

ENCLOSURE 5.

Fixed weather enclosure over entire engine/compressor a.2 Full size tool boxes b.


SPECIFICATION #71 - CUSHION TIRE LIFT TRUCK - 4,000 LB CAPACITY2019 Caterpillar 2CC40002019 Mitsubishi FG252019 Toyota 8FGCU20


ENGINE:1.

50 hp LP gas engine a.

TRANSMISSION:2.

Powershift type a.Inching pedal b.1 speed forward, 1 speed reverse c.

HYDRAULIC SYSTEM:3.

19.0 gpm at 2250 psi a.

CHASSIS:4.

Wheelbase - 46" a.Tread width - 33" (with standard tires) b.Ground clearance at lowest point - 3" c.Tire size:

Front - 18.0 x 7 x 12 cushion tire 1.Rear - 14.0 x 5 x 10 cushion tire 2.

d.

Steering radius - 72" e.Brakes:

Hydraulic service brakes 1.Mechanical parking brake 2.

f.

LIFT:5.

Two stage lift mast a.Lift height minimum - 130" b.Lift capacity - 4000 lbs. c.Fork spacing - 7" to 32" minimum d.Tilt - 5 degrees forward/10 degrees backward e.

MISCELLANEOUS:6.

FOPS protection a.Work lights b.Seat belts c.


SPECIFICATION #72 - SCISSOR LIFT - SELF PROPELLED2019 Genie GS-19302019 Haulotte Optimum 1930 E2019 JLG 1930 ES



64" x 29" Platform a.36" Extension Deck b.25' Working Height (raised) c.18' Platform Height (raised) d.Lift Capacity 500 lbs. e.

POWER:2.

24 Volt a.4-6 Volt Batteries b.On Board Charging System c.Dual Front Wheel Drive d.

BRAKES:3.

2 or 4 wheel brakes a.

PLATFORM:4.

Fixed rails a.36" Extension Deck b.AC Power to platform c.Lanyard attachment points (2) d.

SAFETY:5.

Manual platform lowering a.Emergency Stop on Platform and Ground control b.Descent alarm c.Hour meter d.Horn e.Pothole guards f.On board diagnostic system g.Tilt lever sensor with alarm h.Scissor maintenance prop i.


SPECIFICATION #73 - RUBBER TIRE MATERIAL HANDLER, 48,000 LB OPERATINGWEIGHT

2019 Caterpillar MH30222019 Sennebogen 818E


ENGINE1.

Tier IV Final Diesel Engine - 132 hp a.Spin on Filters b.Two Stage Air Cleaner c.

WEIGHT2.

Minimum Operating Weight - 48,000 lbs a.

TRAVEL SYSTEM3.

2-speed - 0-3.0 mph/0-12.0 mph a.

HYDRAULIC SYSTEM4.

Main Hydraulic System flow 80 GPM a.

UNDERCARRIAGE5.

Two axles with all wheel drive a.8 - 10:00X20 Solid Tires b.

OPERATING STATION6.

Cab to be climate controlled with pressurized filtration a.Hydraulic elevating cab b.Sliding door window and tilt out front window c.Tinted windows with safety glass d.Adjustable suspension seat with safety belt and seat heater e.Catwalk with handrail f.Fire extinguisher g.Rear view and right view camera system h.Halogen work lights on roof cap i.

WORKING EQUIPMENT7.

Purpose built material handling boom and stick a.Safety check valves on boom and stick cylinders b.


SPECIFICATION #74 - HYBRID LIGHT TOWER 2019 MPMC MLT4x150-9155L Hybrid Light Tower2019 SignalPower HT444PC



Length 174" a.Width - Solar Panels Retracted 69" b.Height 72" c.Mast Deployed Height 30' d.Weight - 1850 pounds. e.

GENERATOR2.

Perkins 403.F.11-10KW Tier 4 a.2, 20A/120 v Receptacles b.Electric Start c.12-30 Gallon Fuel Tank d.Auto Mode - Automatic Start for Low Battery e.Hybrid Systems Automatically Switches Between Solar Battery, Generator, or Standard Household Current f.

TRAILER3.

Axle 2000 lbs. a.13" Wheels b.Hitch 3 Position Adjustable Ball c.Stabilizers - 2 Extendable Outriggers; 1 Trailer Jack d.Top Mounted Fork Pockets and Single Lifting Eye e.Powder Coated DOT Rated Trailer with Lights f.Trailer Weight - 1850 pounds g.

MAST 4.

30 ft. Extendable Mast in 3 Stages a.Wind Stability to 40 mph b.Rotates 90 Degrees c.

LIGHTS5.

4 Quick Connect 320 Watt each LED Lights a.Dimmer Control b.Instant On/Off c.365 Day Programmable Timer for Lights, On/Off d.Lens Patter Spread of 150 Degrees e.Meets DOT Anti-Glare Regulations f.

SOLAR PANELS6.

5 - 100 Watt Panels a.Operating Temperature - 40c to 46c b.

BATTERIES7.

4 Deep Cycle Batteries a.Optional Lithium Cells b.12 Volt, 220 AMP Hours c.


SPECIFICATION #75 - LIGHT TOWER - TRAILER MOUNTED2019 Chicago Pneumatic - CPLT V42019 Doosan LCV6WKUB-60hz-TY2019 Generac MLT30602019 Wacker Neuson LTN 6L2019 Wanco WLT-4Mk106k

THE FOLLOWING ITEMS WILL BE FACTORY INSTALLED ON THE BASE VEHICLE/EQUIPMENT TO MEETTHE MODEL NUMBER AND BUILD CODES OF THE EQUIPMENT LISTED.


Length 170" a.Width 51" b.Height 74" c.Mast Deployed Height 30' d.Weight - 1610 pounds. e.

ENGINE:2.

3 Cylinder Diesel Engine. a.12 HP at 1800 RPM. b.Engine Protection Shutdown System. c.

GENERATOR:3.

Wattage output 7000 Watt max, 6000 Watt continuous. a.Brushless type. b.120/240 Volts at 60 Hz +/- 6% regulated. c.AMPS at 120/240V - 50/25. d.Insulation class H. e.

FUEL TANK:4.

30 Gallon Capacity. a.Run Time (approx.) 64 hours. b.

TRAILER:5.

Axle 1800 lbs. a.13" tire size. b.Hitch 2" ball. c.Leaf Spring Suspension. d.Tongue Jack. e.4 outrigger jacks. f.

CONTROL PANEL: 6.

Individual breakers for lights. a.Hour meter. b.Cabinet Lights. c.External receptacles: 1-30 AMP 120/240 Volt, twist lock, 1 GFC1, 15 AMP 120 Volt. d.

MAST: 7.

32ft. extendable mast. a.4 each metal halide light heads. b.440,000 lumens. c.360 degree mast rotation. d.Fold down for transport. e.Winch for mast extension. f.


SPECIFICATION #76 - 125KW GENERATOR PACKAGE2019 MPMC MP135S-22019 LJP ULJ1252019 AKSA ULJ-1252019 Blue Star Power Systems JD125-022019 Caterpillar D125-82019 Generac SD1302019 Tradewinds TP125


GENERATOR REQUIREMENTS:1.

Standby duty rated at 125.0 kW, 156.3 KVA, 8 power factor. a.480 volts b.3 phase, 60 hertz, 1800 rpm c.Directly connected to the engine flywheel housing with flex coupling. d.Generator shall meet performance class G3 of IEC. e.Unit shall be in compliance with and be UL 2200 labeled. f.

ENGINE:2.

Water cooled diesel engine, sized for generator set. a.Emission compliant engine. b.

CONTROLS:3.

Solid state, microprocessor based generator controls. a.Controls shall provide all operating, monitoring and control functions for generator set. b.

ENCLOSURE/SILENCER:4.

Complete diesel engine generator set including control panel, engine starting batteries and fuel oil tank shall be enclosed in a factoryassembled water protective, sound attenuated enclosure.

a.

Critical grade silencer. b.Companion flanges. c.Flexible stainless steel exhaust. d.

FUEL TANK:5.

Double wall sub-base tank integral to enclosure. a.24 hour capacity at 100% at full load. b.Rupture basin with 110% capacity. c.Locking fuel caps. d.Mechanical fuel level gauge. e.Low fuel level alarm contact. f.Fuel tank rupture alarm contact. g.Must meet UL 142 and FDEP standards. h.

BATTERY CHARGER:6.

Current limiting battery charger to automatically charge batteries. a.Charger shall be dual charge rate with automatic switching to boost rate when required. b.Charger shall be mounted on genset package. c.

START UP AND TESTING:7.

Vendor must coordinate all start up and testing activities with the engineer and owner. After installation is completed by others andnormal power is available, the vendor must perform a one (1) day start-up including the use of building load. The start-up technicianwill instruct all necessary personnel how to operate and maintain the equipment in accordance to the manufacturer's requirements.

a.

CONDITIONS:8.

In addition to equipment specified, each generator shall be equipped with all standard equipment as specified by the manufacturefor this model and shall include but not be limited to the following necessary items:

Initial filling of oil and antifreeze. 1.Shrink wrap applied to the product to ensure a clean finish. 2.During the start-up, the technician shall record the following information and provide to the owner for his records: 3.

a.

Record Operating Voltage, Hz, Ph, and connected load (Amperage) b.

Package information consisting of Make of generator (Cat, Wacker, or Tradewinds), Model (TJ125 TP20, DP125, etc.), Serialnumber of complete package, and Start-up date.

c.

Record engine and generator serial numbers. One complete set of operation and maintenance manuals. 1.Two (2) year or 1500 hour standard standby generator warranty. Labor, materials, and travel for the warranty period repairwill be paid by manufacturer during normal business hours.

2.

d.


SPECIFICATION #77 - 150KW MOBILE GENERATOR PACKAGE2019 Blue Star Power Systems VD150-02 FT42019 Chicago Pneumatic CPG-250 T4F2019 Doosan G190 WCU-34-T4F2019 Generac/Magnum MDG175DF42019 LJP AT1502019 MPMC MP150S-22019 Multiquip DCA 220SSJU4F2019 TechnoGen FP200TSX2019 Tradewinds TP1502019 Wacker Neuson G180


GENERATOR REQUIREMENTS:1.

Standby duty rated at 150kwe, 187kva, 8 power factor. a.Prime power duty rating 135kwe, 168kva, 0.8 power factor. b.Main Breaker shall be equipped with shunt trip. c.Generator end shall be Direct coupled to the engine flywheel with a flexible coupling. d.Generator shall meet performance class G3 of IEC. e.Jacket water heater. f.

ENGINE:2.

6 cylinder, water cooled, 1800rpm, diesel engine. a.Current emission compliant diesel engine. b.Spin on fuel and oil filters. c.

VOLTAGE CHANGE OVER SWITCH & DISTRIBUTION:3.

Manual 3 position voltage change over switch to select each voltage as specified when the unit is not running. a.1ph 120/240, 3ph 120/240, 3ph 120/208, and 3ph 277/480. b.A five point connection shall be provided for ease of connection of load leads. c.One 50amp, 120/240vac, 1 ph, twist lock receptacle. d.One 30amp, 120/240vac, 1 ph, RV type receptacle. e.Two 20amp, 120/240vac, 1 ph, duplex receptacle. f.Two 20amp, 120/240vac, 1ph, duplex GFI receptacle. g.Each receptacle shall be protected by a individual circuit breaker. h.A receptacle shall be provided to power both the jacket water heater and on board battery charger. i.Two thumb screw type connection points shall be provided for remote auto start. j.

CONTROLS:4.

Solid state, microprocessor based generator controls. a.Controls shall provide all operating, monitoring and control functions for the generator set. Controls shall provide for auto start/stopfunctions.

b.

A emergency stop push button will be installed. c.A voltage adjustment shall be provided in the panel to adjust voltage in all voltage positions. d.A switch shall be provided in the panel to turn all power off in the panel if not being used. e.

ENCLOSURE:5.

Complete diesel engine generator set including control panel, engine starting batteries and fuel tank shall be enclosed in a factoryassembled weather protective, sound attenuated enclosure. The sound attenuated enclosure noise level is not to exceed 73 – 75dba@ 21 feet.

a.

Oil and water drain lines shall be provided and extend to the enclosure wall with valves for easy service. b.Critical grade silencer. c.Companion flanges. d.Flexible exhaust-flex. e.Keyed alike lockable doors. f.

IN BASE FUEL TANK TRAILER:6.

Trailer shall be DOT approved with proper serial number data plate indicating weight capacity minimum of 10,000lbs. a.Trailer will have dual axles with torque springs to reduce overall height of package. b.Standard 7 or 5 pin vehicle hitch receiver to be supplied. c.Trailer will have two rear level jacks with sand shoes and front leveling jack. d.Trailer will have hydraulic brakes. e.

Trailer will have all necessary safety equipment to include but not be limited to an adjustable and removable pintle hitch, 30 inchsafety chains, fenders, lights per DOT, and break away cable.

f.

Tires will be minimum load range type "D" (8 ply rating) with matching steel rims. Rims are to be finish painted. g.Minimum 8 hour capacity at 75% load rating to determine single wall tank size. h.A mechanical fuel gauge will be provided. i.Locking fuel cap. j.Low fuel level alarm. k.All necessary vents and caps will be provided along with suction, return, and drain points. l.

BATTERY CHARGER:7.

Battery will be installed in holding container with battery cables. a.Current limiting battery charger to automatically charge batteries. b.Charger shall be dual charge rate with automatic switching to boost rate when required. c.Charger mounted inside generator set package. d.Fully charged battery will be provided at time of delivery and start-up. e.

START UP & COMMISSIONING:8.

One (1) day start-up including operational test of equipment showing proper connection of cables with safety issues performed by afactory trained technician. The start up technician will instruct personnel how to operate and maintain the equipment in accordancewith the manufacturer's requirements.

a.

CONDITIONS:9.

In addition to equipment specified, each generator shall be equipped with all standard equipment as specified by the manufacturerfor this model and shall include but not be limited to the following items:

All product shall be new and of current design. 1.Initial filling of oil and antifreeze. (diesel fuel by others) 2.During start-up, the technician shall record the following information and provide to owner for his records: 3.

a.

Operating Voltage, Hertz, Phase, and connected load (Amperage). [if any] b.Package information consisting of Make of generator (Cat, Wacker, or Tradewinds), Model (TJ125 TP20, DP125, etc.), Serialnumber of complete package, and Start-up date.

c.

Written Information consisting of make, model, serial number, and start-up date. d.Record Engine and Generator Serial numbers.

One complete set of operation and maintenance manuals. 1.Two (2) year or 1500 hour standard mobile generator warranty will apply. Generator to be transported to authorizedservicing dealer for warranty repair during normal business hours.

2.

e.

TRAILER10.

The trailer must have a vin and a certificate of origin a.


SPECIFICATION #78 - 500KW GENERATOR PACKAGE2019 AKSA APD-ULJ5002019 Blue Star Generator (VD500-01)2019 Caterpillar 15 ACERT2019 Generac SD5002019 LJP ULJ5002019 MPMC MP500S-22019 Tradewinds T5002019 Wacker Neuson G625


GENERATOR REQUIREMENTS1.

Standby duty rated at 500kwe, 625kva, 0.8 power factor a.480 volts b.Voltage options are: 120/240, 120/208 or 277/480 3ph c.Directly connected to the engine flywheel housing with a flex coupling d.Generator shall meet performance class G3 of IEC e.Unit shall be compliance with UL 2200 specifications f.

ENGINE2.

6 cylinder, water cooled, 1800rpm, diesel engine a.Emission compliant engine to stationary standby regulations b.

CONTROLS3.

Solid state, microprocessor based generator controls a.Controls shall provide all operating, monitoring and control functions for the generator set. b.Control panel is NFPA110 Compliant c.

ENCLOSURE/SILENCER4.

Complete diesel engine generator set including control panel, engine starting batteries and fuel oil tank shall be enclosed in a factoryassembled weather protective, sound attenuated enclosure with oil and water drain lines

a.

Enclosure shall be constructed from aluminum, preferably out of .125 thickness and 5058 marine grade aluminum. b.Critical grade silencer (25DB Reduction) c.Companion flanges d.Flexible stainless steel exhausts flex. e.

FUEL TANKS5.

Double wall sub-base diesel fuel tank shall be integral to the enclosure a.24 hour capacity at 75% load rating b.Rupture basin will be of 110% capacity c.Locking fuel caps d.All necessary vents and caps will be provided e.Mechanical fuel level gauge f.Low fuel level alarm contact g.Fuel tank rupture basin alarm contact h.Must meet UL 142 and FDEP standards i.

BATTERY CHARGER6.

Current limiting battery charger to automatically charge batteries a.Charger shall be dual charge rate with automatic switching to boost rate when required. b.Charger shall be mounted on genset package. c.

DELIVERY7.

Net cost includes delivery of equipment to governmental site location. a.Coordination and offloading of the equipment at the governmental site location will be the responsibility of the purchasing agency. b.

START UP AND COMMISSIONING8.

Vendor must coordinate all start up and testing activities with the engineer and owner. After installation has been completed,approved by the local electrical inspector, and normal power is available, the vendor will perform a One (1) day start-up includingthe use of building load. The start up technician will instruct all necessary personnel how to operate and maintain the equipment inaccordance to the manufacturer's requirements.

a.

CONDITIONS9.

In addition to equipment specified, each generator shall be equipped with all standard equipment as specified by the manufacturefor this model and shall include but not be limited to the following necessary items:

a.

Initial filling of oil and antifreeze b.Shrink Wrap applied to the product to ensure a clean finish c.During the start-up, the technician shall record the following information and provide to the owner for his records:Record OperatingVoltage, Hz, Ph, and connected load (Amperage); Package Information consisting of Make, Model, Serial number, and Start-upDate; Record Engine and Generator Serial numbers.

d.

One complete set of operation and maintenance manuals. e.Two (2) years or 1000 hours standard standby generator warranty, whichever occurs first. Labor, materials, and travel for thewarranty period repair will be paid by manufacturer during normal business hours.

f.


SPECIFICATION #79 - 500KW MOBILE GENERATOR PACKAGE2019 Blue Star Generator (VD500-02-FT4)2019 Caterpillar 500 kW (XQ570)2019 Holland PT6TPC-P1104D44T2019 MPMC MP500S-22019 Tradewinds T5002019 Wacker Neuson G625


GENERATOR REQUIREMENTS1.

Standby duty rated at 500kwe, 625kva, 0.8 power factor. a.Prime power duty rating 450kwe, 563kva, 0.8 power factor. b.Main Breaker shall be equipped with shunt trip. c.Generator end shall be Direct coupled to the engine flywheel with a flexible coupling. d.Generator shall meet performance class G3 of IEC. e.

ENGINE2.

6 cylinder, water cooled, 1800rpm, diesel engine. a.Current emission compliant diesel engine. b.Spin on fuel and oil filters. c.Jacket water heater with service valves to ensure coolant does not need to be drained if heater needs service. d.120vac, 1ph, 60hz input 10 amp, 24vdc, output automatic battery charger. e.Standard 4D lead acid batteries with battery rack and cables. f.

VOLTAGE CHANGE OVER SWITCH AND DISTRIBUTION3.

Manual 2 position voltage change over switch to select each voltage as specified when the unit is not running a.3ph 120/208, and 3ph 277/480 b.Load leads shall be attached to the generator using two (2) forms and shall be rated for 2000 amps. Generator will be equipped withboth:c-1. Five (5) compression lugs per phase rated for 400 amps each

c.

A 20 amp, 120vac, 1ph, male receptacle shall be provided to power the jacket water heater. d.A 20 amp, 120vac, 1ph, male receptacle shall be provided to power the battery charger. e.Two thumb screw type connection points shall be provided for remote auto start. f.

CONTROLS4.

Solid state, microprocessor based generator controls a.Controls shall provide all operating, monitoring and control functions for the generator set. Controls shall provide for auto start/stopfunctions.

b.

An emergency stop push button will be installed. c.A voltage adjustment shall be provided in the panel to adjust voltage in all voltage positions. d.A switch shall be provided in the panel to turn all power off in the panel if not being used. e.A front face mounted circuit breaker shall be provided to protect the panel from any D.C. spikes. f.

ENCLOSURE5.

Complete diesel engine generator set including control panel, engine starting batteries and fuel tank shall be enclosed in a factoryassembled weather protective, sound attenuated enclosure. The sound attenuated enclosure noise level is not to exceed 80 dba @ 21feet.

a.

Enclosure shall be constructed from aluminum, preferably out of .125 thickness and 5058 marine grade aluminum. b.Oil and water drain lines shall be provided and extend to the enclosure wall with brass ball valves for easy service. c.Critical grade silencer (25db reduction). d.e.Companion flanges. e.f.Flexible exhaust-flex. f.g.Keyed-alike lockable doors. g.

IN BASE FUEL TANK TRAILER6.

Trailer shall be DOT approved with proper serial number data plate indicating weight capacity minimum of 20,000lbs. a.Trailer will have dual axles with torque springs to reduce overall height of package. b.Standard 7 pin vehicle wiring connector to be supplied. c.Trailer will have two rear level jacks with sand shoes and front leveling jack. d.Trailer will have hydraulic brakes. e.Trailer will have all necessary safety equipment to include, but not be limited to, an adjustable and removable pintle hitch, 36 inchsafety chains, fenders, lights per DOT, and break away cable.

f.

Tires will be minimum load range type "D" (8 ply rating) with matching steel rims. Rims are to be finish painted. g.

h.Minimum 8 hour capacity at 75% load rating to determine single wall tank size. h.A mechanical fuel gauge will be provided. i.Locking fuel cap. j.Low fuel level alarm. k.All necessary vents and caps will be provided along with suction, return, and drain points. l.

BATTERY CHARGER7.

Battery will be installed in holding container with battery cables. a.Current limiting battery charger to automatically charge batteries. b.Charger shall be dual charge rate with automatic switching to boost rate when required. c.Charger mounted inside generator set package. d.Fully charged battery will be provided at time of delivery and start-up. e.120 volt shore power connector for battery charger. f.

START UP AND COMMISSIONING8.

One (1) day start-up including operational test of equipment showing proper connection of cables with safety issues performed by afactory trained technician. The start up technician will instruct personnel how to operate and maintain the equipment in accordancewith the manufacturer's requirements.

a.

CONDITIONS9.

In addition to equipment specified, each generator shall be equipped with all standard equipment as specified by the manufacturerfor this model and shall include, but not be limited to, the following items:

a.

All product shall be new and of current design. b.Initial filling of oil and antifreeze (diesel fuel by others). c.During start-up, the technician shall record the following information and provide to owner for his records:i.Operating Voltage,Hertz, Phase, and connected load (Amperage-if any).ii.Written Information consisting of make, model, serial number, and start-update.iii.Record Engine and Generator Serial numbers.

d.

One complete set of operation and maintenance manuals. e.Two (2) years or 1000 hours standard mobile generator warranty will apply, whichever occurs first. Generator to be transported toauthorized servicing dealer for warranty repair during normal business hours.

f.

TRAILER10.

The trailer must have a vin and a certificate of origin. a.


SPECIFICATION #80 - 600 AMP AUTOMATIC TRANSFER SWITCH2019 ASCO Series 3002019 Caterpillar CTG Series2019 GE Zenith ZTG6002019 Generac GTS6002019 Thomson TS 870


AUTOMATIC TRANSFER SWITCH:1.

Maximum voltage rating of 600Vac, 60hz a.1ph or 3ph b.Open transition (break-before-make) transfer logic c.Transfer switch must meet the related industry standards:

UL 1008 - Automatic transfer switches for use in emergency systems 1.CSA - Automatic transfer switches 2.NEMA - Industrial control and systems AC transfer switch equipment 3.IEC - Automatic transfer switching equipment 4.

d.

RATING:2.

600 amp, 3 pole, 277/480vac, 60hz a.Enclosure type: NEMA 3r b.

FUNCTIONAL:3.

The automatic transfer switch shall automatically transfer the load to the generator supply in the event of a utility supply failure andreturn the load to the utility supply upon restoration. The automatic transfer switch power switching devices shall be mechanicallyand electrically interlocked to prevent the utility and generator supplies from being interconnected.

a.

All timers should be field adjustable to ensure proper field site compatibility. b.

AUTOMATIC SEQUENCE OF OPERATION:4.

When the voltage on any phase of the utility supply is below present levels of rated voltage for a preset time delay, a contact shallclose to initiate start of the standby generator.

a.

The load shall transfer to the generator supply when the generator voltage and frequency have reached acceptable present levels andthe warm-up time delay has expired.

b.

When the utility supply is restores to the above present levels of rated voltage on all phases, load transfer from generator to utilitysupply shall be initiated following expiry of the utility return timer.

c.

Once the transfer mechanism operates and opens the generator power switching device, the transfer mechanism shall stop in theneutral position (i.e. with the both power switching devices open) for the duration of the neutral delay timer setting to allow loadvoltage to decay prior to reconnecting the utility supply.

d.

The load shall be re-connected to the utility supply once the neutral delay timer expires and the transfer mechanism continuesoperation and closes the utility power switching device.

e.

The load shall immediately retransfer to the utility supply (if within acceptable limits) should the generator supply fail prior to theexpiry of the utility transfer delay.

f.

The generator set shall continue to operate following a load transfer for a cool down delay period, and then a contact shall open tostop the generator set.

g.

An "on load" test mode may be initiated which shall cause a simulated utility failure condition and transfer the load to the generatorset. The transfer sequence shall be the same as for a utility power failure except a neutral delay sequence shall occur whentransferring from utility to a generator source.

h.

The load shall immediately retransfer to the utility supply (if within acceptable limits) should the generator supply fail during an "onload" test mode.

i.

FACTORY TESTING:5.

A certified factory test report shall be shipped with each switch at time of shipment. a.The automatic transfer switch shall be factory tested prior to delivery to the purchaser. The following test shall be conducted byqualified factory personnel:

Visual Inspection 1.Mechanical Tests 2.Electrical Tests 3.Final Inspection 4.

b.

FIELD TESTING AND COMMISSIONING:6.

The automatic transfer switch shall be field tested once installed at the project site to confirm proper operation of the system.a.

The automatic transfer switch shall be field tested once installed at the project site to confirm proper operation of the system.Schedule and witness testing activities shall be coordinated with the project engineer, site contractor, and owner as required inadvance of the testing date. A qualified local factory-trained field representative shall conduct the necessary test to ensure properoperation of the switch.

a.

Visual Inspection: Electrical and Mechanical inspection to verify the installation is correct as recommended by the transfer switchmanufacturer and as per National Electric Code (NEC) requirements.

b.

Mechanical Tests: As a minimum, the following mechanical tests shall be performed on the transfer switch: Power conductor torque verification 1.Verification of mechanical interlock 2.Manual ATS Mechanism Operation 3.All Mechanical Fasteners/Wire Connections Tight 4.Confirmations of correct transfer switch voltage, current and withstand ratings as is required for the application. 5.Meggar testing the power cabling to the transfer switch. 6.Verification of correct power cabling phasing and phase rotation prior to energization. 7.Confirmation of settings for all timers & voltages sensors. 8.Full Function test-normal operation – 3 complete cycles of failing the utility supply, and transfer load to/from the generatorset.

9.

Verification of all test modes operates correctly. 10.

c.

CONDITIONS:7.

In addition to equipment specified, each automatic transfer switch shall be equipped with all necessary equipment as specified bythe manufacturer for this model and shall include but not be limited to the following necessary items:

Shrink Wrap applied to the product to ensure a clean finish. 1.One complete set of operation and maintenance manuals. 2.A two (2) year or 1500 hour from date of standard standby warranty will apply from date of successful start-up. Labor,materials, and travel for the warranty period repair will be paid by manufacturer during normal business hours.

3.

a.


SPECIFICATION #81 - 6 INCH MOBILE PUMP PACKAGE2019 BBA BA150E2019 Godwin CD150M2019 Pioneer PP66S12L712019 Holland Pumps (PT6TPC-P1104D44T)2019 Supervac Triton2019 Thompson 6JSC2019 Tradewinds TPK064750


DESIGN REQUIREMENTS:1.

Discharge size: 6 inches a.Suction size: 6 inches b.Capable of 1750 GPM minimum c.Capable of 160 ft. Total Dynamic Head (TDH) minimum d.Duty Point, Maximum: 1,000 gallons per minute minimum (GPM) at 120 ft. Total Dynamic Head (TDH) e.Impeller Diameter: Manufacturer's standard for pump f.Operating Speed Maximum: 2,200 RPM g.Solids Handling Size, Maximum: 3 inches h.

ENGINE:2.

Diesel engine, appropriate to pump size at continuous duty. a.Emission compliant engine b.Industrial grade exhaust muffler and rain cap c.Oil and water drain lines with ball valves d.Low water level shutdown switch e.12vdc system with battery rack and cables f.50 gallon minimum fuel tank with low fuel level alarm and shutdown. g.

PUMP:3.

Check valve a.Impellers b.Self priming system c.

CONTROLS:4.

Solid state, microprocessor based pump controls. a.Controls shall provide all operating, monitoring and control functions for the pump set. b.Controller will also provide 2 fully programmable contacts for input and output signals accordingly. c.Controller will provide remote start stop control with adjustable ramp (speed) time control. d.UL 508 R and CSA C22.2 No. 14 approved. e.

TRAILER:5.

The manufacturer shall mount the diesel engine and pump unit with the above 50 gallon subbase tank on a street legal D.O.T.approved trailer. This trailer will be able to be rated for a safe travel at speeds of 60 mpg and not be limited to the followingspecifications:

Trailer design shall be such that the County/City may easily remove the entire engine, fuel tank and pump from the trailer. 1.12vdc electric system 2.Lunette or military type towing ring with safety chains. 3.Single point lifting bar. 4.License plate bracket 5.Sand shoe type support stands front and rear. 6.Torque spring axles to meet load of trailer. 7.

a.

The trailer must have a vin and a certificate of origin. b.

START UP AND COMMISSIONSING:6.

Vendor must coordinate all start up and testing activities with the engineer/owner. After field delivery of the pump and trailer, anauthorized factory representative shall perform the initial start up and field testing of the pump and trailer. If conditions permit, asite will be determined where connection will be made by the County/City to test the pump package. If a site cannot be prepared astandard operational test will be performed.

a.

At the same time the start up test is performed, the factory representative will provide all necessary operation, field maintenance andminor repair training as necessary. This will also include safety procedures and hazard assessment.

b.

CONDITIONS:7.

In addition to equipment specified, each pump package shall be equipped with all standard equipment as specified by themanufacturer for this model and shall include but not be limited to the following necessary items:

Initial filling of oil and antifreeze. 1.During the start up, the authorized factory representative shall record and provide the County/City with the engine andpump serial numbers for the owner records. At this time the warranty will begin.

2.

One complete set of operations and maintenance manuals. 3.Two (2) year or 1500 hour standard standby pump package warranty. Labor, materials, and travel for the warranty periodrepair will be paid by manufacturer during normal business hours.

4.

a.


SPECIFICATION #82 - AQUATIC WEED CUTTER WORKBOAT2019 Weedoo TigerCat Workboat


GENERAL DIMENSIONS1.

Height- 8' a.Width-7' 3" b.Length- 15' c.Height from waterline- 48" d.Boat draft- 4" to 6" e.Weight - 2285 lbs f.

ENGINE2.

3 cylinder diesel engine a.Liquid cooled b.Electric start, and charging system c.

HYDRAULICS3.

Triple pump design a.27 GPM b.Eco friendly hydraulic fluid c.

PROPULSION4.

Twin hydraulic outdrives a.Weed and mud design propellers b.

VESSEL HULL5.

Fiberglass/ Kevlar design a.Deck mounted cutter and loader b.

BOOM CUTTER6.

Hydraulic drive a.Full articulation to cut 5' below waterline b.

FRONT END LOADER7.

Marine type vegetation bucket a.

OPERATOR STATION8.

All hydraulic functions/propulsion functions controls a.

TRAILER9.

Trailer to be designed specifically for this workboat and will meet all federal, state, and local laws for a trailer operated on thehighway.

a.


SPECIFICATION #83 - AQUATIC HARVESTER WORKBOAT2019 Weedoo Aqua Harvester 334


GENERAL DIMENSIONS1.

Height- 5' a.Width- 7' 3" b.Length- 15' c.Belt length- 5' 10" d.Belt width-39.9" e.Weight with twin motors-1800lbs f.

POWER PACK2.

24 volt electrical system a.Lithium batteries b.Solar charger c.Onboard marine charger d.

CONVEYOR3.

Electric driven conveyor collector a.Detachable bag collector assembly b.

PROPULSION4.

Twin electric motor outdrives a.Weed and mud design propellers b.

VESSEL HULL5.

Fiberglass/ kevlar design a.Front mounted conveyor b.

OPERATOR STATION6.

All workboat controls to be located at the captain helm station a.

TRAILER7.

A trailer specifically designed for this workboat meeting all Federal, State and local laws for a trailer operated on public roads a.

FLORIDA SHERIFFS ASSOCIATION & FLORIDA ASSOCIATION OF … · 2018-12-21 · florida sheriffs...

Documents

Transcript of FLORIDA SHERIFFS ASSOCIATION & FLORIDA ASSOCIATION OF … · 2018-12-21 · florida sheriffs...