Floor boxes & grommets catalogue
description
Transcript of Floor boxes & grommets catalogue
26
Access floor service outlet boxesempty boxes and accessory plates
112 mmwidth plates
100 mmwidth plates
75 mmwidth plates
To configure boxes as required, select :
1. Box depth2. Number of compartments required3. Desired accessory plates
4 compartment
230 m
m
366 mm
3 compartment
230 m
m
366 mm
2 compartment
230 m
m
290 mm
CR2001 CR011 CR4001
CR2002 CR012 CR4002
CR2003 CR013 CR4003
CR2004 CR014 CR4004
CR2005 CR015 CR4005
CR2006 CR016 CR4006
CR2100 CR020 CR4100
CR2101 CR022 CR4101
CR2102 CR023 CR4102
CR2104 CR029 CR4104
CR2105 CR030 CR4105
CR2116 CR044 CR4118
CR2112 CR036 CR4111
CR2115 CR043 CR4117
CR2106 CR026 –
CR2107 CR028 –
– CR042 CR4115
– CR031 CR4106
CR2109 CR033 CR4108
CR2113 CR024 CR4112
CR2114 CR025 CR4113
Single base – 75 mm depth
Single base – 85 mm depth (standard box)
Single base – 110 mm depth
Separate compartment base – 75 mm depth
Separate compartment base – 85 mm depth
Separate compartment base – 110 mm depth
Blank plate
2 gang switched socket outlet
2 gang switched socket outlet, low noise / clean earth
2 gang unswitched socket outlet
3 gang unswitched socket outlet
3 gang unswitched socket outlet,low noise / clean earth
2 gang RCD socket outlet
2 gang RCD socket outlet, low noise / clean earth
Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)
Punched plate for 2 gang accessories (120·6 mm fixing centres)
Angled punched plate for 4 x RJ45 sockets(37 mm x 22 mm cut-outs)
2 x LJ2 accessory plate (50 mm fixing centres)
4 x BNC connector plate
4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
Empty boxes Example
Plates For 2 compartment boxes For 3 compartment boxes For 4 compartment boxes
026_027_D2010 v3.qxd 1/6/10 12:25 Page 26
27
230 m
m
366 mm
230 m
m
366 mm
For 3 compartment boxes For 4 compartment boxesAdditional plates
Access floor service outlet boxespre-wired boxes
Includes 1 x twin switched socket outlet
Includes 2 x twin switched socket outlets
Pre-wired service outlet boxes with Electrak tap-offs
1. Select box depth and desired configuration2. Select additional accessory plates (if required)
4 compartment3 compartment
CR100 CR122
CR101 CR123
CR110 CR132
CR111 CR133
CR020 CR4100
CR022 CR4101
CR023 CR4102
CR029 CR4104
CR030 CR4105
CR044 CR4118
CR036 CR4111
CR043 CR4117
CR026 –
CR028 –
CR042 CR4115
CR031 CR4106
CR033 CR4108
CR024 CR4112
CR025 CR4113
Single base – 85 mm depth, pre-wired with3 m standard tap-off
Single base – 85 mm depth, pre-wired with5 m standard tap-off
Single base – 85 mm depth, pre-wired with3 m low noise / clean earth tap-off
Single base – 85 mm depth, pre-wired with5 m low noise / clean earth tap-off
Blank plate
2 gang switched socket outlet(1)
2 gang switched socket outlet, low noise / clean earth(1)
2 gang unswitched socket outlet(1)
3 gang unswitched socket outlet(1)
3 gang unswitched socket outlet,low noise / clean earth(1)
2 gang RCD socket outlet(1)
2 gang RCD socket outlet, low noise / clean earth(1)
Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)
Punched plate for 2 gang accessories (120·6 mm fixing centres)
Angled punched plate for 4 x RJ45 sockets(37 mm x 22 mm cut-outs)
2 x LJ2 accessory plate (50 mm fixing centres)
4 x BNC connector plate
4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
Pre-wired boxes Example
(1) Additional sockets will require wiring on site
026_027_D2010 v3.qxd 1/6/10 12:26 Page 27
Access floor service outlet boxes2 and 3 compartment boxes
28
Pack Cat. Nos. 3 compartment
Empty boxes
100 mm compartment widths
1 CR011 Single base - 75 mm depth
1 CR012 Single base - 85 mm depth (standard box)
1 CR013 Single base - 110 mm depth
1 CR014 Separate compartment base - 75 mm depth
1 CR015 Separate compartment base - 85 mm depth
1 CR016 Separate compartment base - 110 mm depth
Accessory plates – 100 mm width
1 CR020 Blank plate
1 CR022 2 gang switched socket outlet
1 CR023 2 gang switched socket outlet, low noise / clean earth
1 CR029 2 gang unswitched socket outlet
1 CR030 3 gang unswitched socket outlet
CR044 3 gang unswitched socket outlet,low noise / clean earth
1 CR036 2 gang RCD socket outlet
1 CR043 2 gang RCD socket outlet, low noise / clean earth
1 CR026 Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)
1 CR028 Punched plate for 2 gang accessories (120·6 mm fixing centres)
1 CR042 Angled punched plate for 4 x RJ45 (37 mm x 22 mm cut-outs)
1 CR031 2 x LJ2 accessory plate (50 mm fixing centres)
1 CR033 4 x BNC connector plate
1 CR024 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
1 CR025 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
3 compartment pre-wired boxes
100 mm compartment widths
Single base – 85 mm depth, pre-wired with :
1 CR100 2 gang switched socket outlet and 3 m standard tap-off
1 CR101 2 gang switched socket outlet and 5 m standard tap-off
1 CR110 2 gang switched socket (low noise / clean earth) and3 m low noise / clean earth tap-off
1 CR111 2 gang switched socket (low noise / clean earth) and5 m low noise / clean earth tap-off
Pack Cat. Nos. 2 compartment
Empty boxes
112 mm compartment widths
1 CR2001 Single base - 75 mm depth
1 CR2002 Single base - 85 mm depth (standard box)
1 CR2003 Single base - 110 mm depth
1 CR2004 Separate compartment base - 75 mm depth
1 CR2005 Separate compartment base - 85 mm depth
1 CR2006 Separate compartment base - 110 mm depth
Accessory plates – 112 mm width
1 CR2100 Blank plate1 CR2101 2 gang switched socket outlet
1 CR2102 2 gang switched socket outlet, low noise / clean earth
1 CR2104 2 gang unswitched socket outlet
1 CR2105 3 gang unswitched socket outlet
CR2116 3 gang unswitched socket outlet,low noise / clean earth
1 CR2112 2 gang RCD socket outlet
1 CR2115 2 gang RCD socket outlet, low noise / clean earth
1 CR2106 Punched plate for 2 x 1 gang accessories (60·3 mm fixing centres)
1 CR2107 Punched plate for 2 gang accessories (120·6 mm fixing centres)
1 CR2109 4 x BNC connector plate
1 CR2113 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
1 CR2114 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
Electrak tap-offs (see p. 18-21)
Selection chart (p. 26-27)Dimensions and technical information (p. 31)
Lid and trim mouldings are precision engineered from hard wearing durable ABS. Lid is reinforced with a Zintec coated mild steel plateMounting frame and box base - 0·9 mm thick galvanised steelEach compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduitsGrey mouldings. Alternative colours available to special order. Goosewing grey plates2, 3 and 4 compartment boxes are also available with separate individual compartment base units for convenient offsite pre-wiringSupplied in parts or fully assembled and configured to customer specification Conform to IEC-61534-22
CR100
CR012
CR2002
028_029P_D2010 v1.qxd 4/6/10 09:55 Page 28
Access floor service outlet boxes4 compartment boxes and ancillary items
29
Pack Cat. Nos. 4 compartment pre-wired boxes
75 mm compartment widths
Single base – 85 mm depth, pre-wired with :
1 CR122 2 x 2 gang switched socket outlets and 3 m standard tap-off
1 CR123 2 x 2 gang switched socket outlets and 5 m standard tap-off
1 CR132 2 x 2 gang switched socket outlets (low noise / clean earth) and 3 m low noise / clean earth tap-off
1 CR133 2 x 2 gang switched socket outlets (low noise / clean earth) and 5 m low noise / clean earth tap-off
Pack Cat. Nos. 4 compartment
Empty boxes
75 mm compartment widths
1 CR4001 Single base - 75 mm depth
1 CR4002 Single base - 85 mm depth (standard box)
1 CR4003 Single base - 110 mm depth
1 CR4004 Separate compartment base - 75 mm depth
1 CR4005 Separate compartment base - 85 mm depth
1 CR4006 Separate compartment base - 110 mm depth
Accessory plates – 75 mm width
1 CR4100 Blank plate
1 CR4101 2 gang switched socket outlet
1 CR4102 2 gang switched socket outlet, low noise / clean earth
1 CR4104 2 gang unswitched socket outlet
1 CR4105 3 gang unswitched socket outlet
CR4118 3 gang unswitched socket outlet,low noise / clean earth
1 CR4111 2 gang RCD socket outlet
1 CR4117 2 gang RCD socket outlet, low noise / clean earth
1 CR4115 Angled punched plate for 4 x RJ45 (37 mm x 22 mm cut-outs)
1 CR4106 2 x LJ2 accessory plate (50 mm fixing centres)
1 CR4108 4 x BNC connector plate
1 CR4112 4 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
1 CR4113 6 x Data / Telecoms plate (37 mm x 22 mm cut-outs)
Selection chart (p. 26-27)Dimensions and technical information (p. 31)
Lid and trim mouldings are precision engineered from hard wearing durable ABS. Lid is reinforced with a Zintec coated mild steel plateMounting frame and box base - 0·9 mm thick galvanised steelEach compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduitsGrey mouldings. Alternative colours available to special order. Goosewing grey plates2, 3 and 4 compartment boxes are also available with separate individual compartment base units for convenient offsite pre-wiringSupplied in parts or fully assembled and configured to customer specification Conform to IEC-61534-22
CR4002CR122
For other floor box configurations
Contact us on +44 (0) 845 600 6266
Ancillary items for service outlet boxes
1 CR0001 Floor tile cut-out template – 2 compartment
1 CR0003 Floor tile cut-out template – 3/4 compartment
10 CR0000 Cable outlet flap
10 CR0010 Cable routers
50 CR0011 Screws for accessory plates
1 CR0002 Lid – 2 compartment box
1 CR0004 Lid – 3/4 compartment box
1 CR0005 Mounting frame for vinyl floor. For 2 compartment boxReplaces mounting frame attached to base
1 CR0006 Mounting frame for vinyl floor. For 3/4 compartmentbox. Replaces mounting frame attached to base
10 CR0007 Floor box lid handle
Electrak tap-offs (see p. 18-21)
028_029P_D2010 v1.qxd 1/6/10 11:58 Page 29
Access floor service outlet boxesslab floor boxes
Access floor grommetsquick fit floor grommets
30
Pack Cat. Nos. Slab floor boxes
Fast and efficient installation with integrated fixingplatesWide range of power and data accessory platesManufactured from 0·9 mm thick galvanised steelEach compartment has 2 entries for 20 mm and 2 entries for 25 mm flexible conduits
100 mm compartment widths
Use plates from the 3 compartment floor box section
1 CR5102 1 compartment slab floor box1 CR5302 3 compartment slab floor box
112 mm compartment widths
Use plates from the 2 compartment floor box section
1 CR5202 2 compartment slab floor box
75 mm compartment widths
Use plates from the 4 compartment floor box section
1 CR5402 4 compartment slab floor box
Pack Cat. Nos. Floor grommet 144 mm Ø
Can accommodate all cable types or three metalconduits up to a 20 mm diameter or 25 mm withoutfoamSimply secured by pushing down the spring-loaded screws and rotating a quarter turn
1 EG0010 Empty grommet
1 EG0020 Cleaner’s grommet with unswitched socket outlet
1 EG0031 144 mm grommet with punched plate for 4 x RJ45
1 EG0050 Cleaners grommet with switched RCD protectedsocket
1 EG1111 Cleaner’s grommet lid
1 EG1112 144 mm grommet lid
Floor grommet 232 mm Ø
Recommended for installation in light traffic areas
1 EG0055 232 mm grommet
Electrak slab floor boxes are an ideal solution for underfloor power anddata requirementsUsed in conjunction with Electrak floor grommets, slab boxes preventunwanted access to power and data connections
Dimensions and technical information (p. 31)
Quick fit installation from floor tile fixing to cable deploymentPrecision engineered from hard wearing durable flame retardant PC/ABSGrey mouldings. Other colours available to special orderUL 94 VO flame class rating. Grommets conform to IEC-61534-22
EG0010
EG0055 EG0020
CR5102
CR5302
3 compartment slab floor box shown with two twinswitched socket outlets, punched data plate and apower-track tap-off
For information on slab box configurations
Contact us on +44 (0) 845 600 6266
For information on grommet configurationsand RCD protection
Contact us on +44 (0) 845 600 6266
NEW
NEW
030P_D2010 v1.qxd 4/6/10 10:06 Page 30
B
Wing
Push grommet into raised floor tile aperture
Push down spring loaded screws and rotate quarter turn
to secure
Ensure wings are located under floor panel
For honeycombed floor panels one wing should face
downwards and one wing should face upwards
Drop cable access insert into
housing opening
Cable access
insert
Access floor service outlet boxes and grommetstechnical information
31
■ Floor boxes ■ Floor grommet 144 mm ØDimensions
■ Large floor grommet 232 mm ØDimensions
Cut hole in raised floor tile, lowercomplete box into aperture and pushfirmly down
To fit carpet : Detach lid and trim assembly by liftingthe blue locking handles and lifting out.Cut and fit carpet. Push lid and trimassembly back into place
DimensionsLid can accommodate carpets up to 6 mm depthAccessory plates are 172 mm long, with 162 mm fixing centres
MaterialsLid and trim mouldings are precision engineered from hard wearingdurable ABS. Lid is reinforced with a Zintec coated mild steel plateMounting frame and box base - 0·9 mm thick galvanised steelFloor service unit conforms to IEC-61534-22
WiringEach compartment has 2 entries for 20 mm and 2 entries for 25 mmflexible conduits
ColourGrey mouldings. Alternative colours available to special orderGoosewing grey plates
Floor tile cut-out dimensions2 compartment : 263 mm x 203 mm(1)
3 and 4 compartment : 340 mm x 203 mm(1)
Floor cut-out aperture is the same for single base or separatecompartment base
A
C
B
Dimensions from top of floor tile into floor void
(1) The aperture dimension 203 mm has a fixing tolerance between 203 to 205 mm
A B CAccessory Underside lid to top ofbox depth accessory (plug clearance)
(mm) (mm) (mm)
75 35 40
85 45 40
110 45 65
125 mm min
55 mm
90 mm
144 mm Ø
Floor panel cut-out diameter
Recommended holecutter is a 5"/127 mmhole saw blade
127 mm min
144 mm GrommetEG0010
Carpet aperture
Cleaner’s grommetEG0020
8 mm
38·25 mm
66·85 mm
66·85 mm
Large quick fit grommet EG0055
58 mm
232 mm Ø
213 mm min215 mm max
Floor panel cut-out diameter
Recommended hole cutter is aadjustable hole saw blade withØ range of 40 mm - 300 mm
■ To install floor grommet
■ To install box
1
Lift handle and pull to
remove lid
A
DC E
(1) Push down lid to close
(2) If grommet is not in use,
replace cable access insert
Slide lid into lug holes
Complete with unswitchedsocket outlet
2
031P_D2010 v1.qxd 1/6/10 12:02 Page 31