FLEXIM - Heat Tracing · FLEXIM Instruments China Shanghai, China Phone: +86 21 64 95 75 20 Fax:...
4
Non-Intrusive Ultrasonic Clamp-on Flow Measurement for Hazardous Areas FLUXUS ® F808 IECEx / ATEX Zone 1 certified Chemical Industries ______ Petrochemical Industries ______ Downstream - Refining ______ Midstream - Hydrocarbon Transport ______ E&P - Offshore / Onshore ATEX ` , IECEx
Transcript of FLEXIM - Heat Tracing · FLEXIM Instruments China Shanghai, China Phone: +86 21 64 95 75 20 Fax:...
Non-Intrusive Ultrasonic Clamp-on Flow Measurement for Hazardous Areas
FLUXUS® F808 IECEx / ATEX Zone 1 certified
FLEXIM
FLUXUS® F808 IECEx / ATEX Zone 1 certified
FLUXUS® F808 Non-intrusive ultrasonic clamp-on flowmeter for liquids (clamp-on flow measurement according to the transit time difference method - automatic NoiseTrek selection for measurements with high gas or solid content)
Operating temperature of the transmitter:
-40 °C to +60 °C
Physical quantities: volumetric flow rate, mass flow rate, flow velocity
Degree of protection Transmitter(acc. to IEC / EN 60529:
IP66 (corrosion resistant coating - applicable for usage Offshore)
Flow velocity range: 0.01 to 25 m/s
Temperature range (at pipe wall):
-40 °C to +200 °C (-170 °C up to 400 °C and beyond with the WaveInjector mounting fixture)
Pipe diameter range: 10 mm up to 6.5 m
Repeatability: 0.15% of reading ± 0.01 m/s
Accuracy*: ± 0.5% of reading ± 0.01 m/s with field calibration** ± 1.2% of reading ± 0.01 m/s with advanced calibration (optional) ± 1.6% of reading ± 0.01 m/s with standard calibration
Data logger capacity: >100 000 measured values
Loggable values: all physical quantities, totalized values and diagnostic values
Outputs: 1 current output and 1 binary output or 1 current output and Modbus
Communication interface:
RS485, Modbus
Power supply: 100 to 240 V / 50 to 60 Hz or 20 to 32 V DC
Extreme Temperature WaveInjector Mounting Fixture
Rugged VARIOFIX L Mounting Fixture
Technical Data
Chemical Industries______
Petrochemical Industries______
Downstream - Refining______
Midstream - Hydrocarbon Transport ______
E&P - Offshore / Onshore
BU
F808
V2-
1EN
20
13/0
5 S
ubje
ct to
cha
nge
with
out n
otifi
catio
n
FLEXIM GmbH Berlin, GermanyPhone: +49 30 93 66 76 60 Fax: +49 30 93 66 76 80 [email protected] www.flexim.com
FLEXIM Instruments Asia Pte Ltd. SingaporePhone: +65 67 94 53 25 Fax: +65 68 62 28 36 [email protected] www.flexim.com
FLEXIM Instruments China Shanghai, ChinaPhone: +86 21 64 95 75 20 Fax: +86 21 64 95 75 90 [email protected] www.flexim.cn
* under reference conditions and with v > 0.15 m/s** if reference uncertainty better than < 0.2%
Further information can be found in the according F808 Technical Specifications at www.flexim.com
ATEX `, IECEx
Dan Macey
1
Specifically Designed for Demanding Environments
Advantages_____________
- Bi-directional flow measurement over a wide turndown ratio
- Very cost effective: No pipe works No process shut-downs Virtually maintenance-free
- Matched, paired and wet flow calibrated (traceable certification)
- Excellent zero point stability and drift-free
- Independent of pipe size, material, operating pressure and medium
- High tolerance to entrained solids and gases
- Free of wear, tear and abrasion
- Not prone to clogging or corrosion
- No pressure loss or source of potential leaks
- Flow measurement at extreme temperatures from -170 °C up to 400 °C and beyond
Chemical Industry_____________
- Hazardous Organic and Inorganic Media- Acids and Caustics- Polymerization Processes- Infrastructural Processes
Hydrocarbon Products Handling_____________
- Pipeline Monitoring- Allocation Terminals
Crude Oil Refining_____________
- Atmospheric Distillation - Vacuum Distillation- Cracking Units
Oil Exploration On- & Offshore_____________
- FWKO and Separator Outlet- Coalescers- Scrubbers and Reboilers- Produced Water Injection- Chemical Injection
From Exploration and Production to Petrochemical and Chemical ProcessingFrom wellhead to refinery, the flows of crude oil and refined products need to be measured every step of the way. Harsh environments with corrosive atmospheres offshore or hot and dirty applications during crude oil refining require tough solutions.
Also during chemical processing, media such as acids, caustics or highly viscous organic substances place enormous material and mechanical stress upon wetted flow measurement technologies.
FLEXIM offers the better alternative: Being non-intrusive, the measurement system never gets into contact with the media inside the pipe – plant shut-downs for installation are a thing of the past.
The measurement system can never be the cause for a potential pipe leak, cannot be prone to clogging and is virtually maintenance-free.
Suitable for all pipe sizes from 10 mm (3/8 inch) diameter upwards - also no limitation on pipe material and wall thickness.
Providing exceptional reliability and accuracy at high and low flows due to matched transducer pairs and sophisticated internal signal processing.
FLEXIM’s permanently installed and portable flowmeters for explosive and hazardous areas have already been proven worldwide in many demanding applications with major operators.
FLUXUS® F808 IECEx / ATEX Zone 1 certified The rugged FLUXUS® F808 with its flameproof housing and stainless steel (SS316 optional) corrosion resistant transducers is suited for every industrial application – not only offshore. With the connection and electronic compartment being hermetically sealed, the FLUXUS® F808 provides for maximum operational safety, being IECEx / ATEX Zone 1 certified.
Because of the extremely robust transducers and the VARIOFIX mounting fixture, which ensures a permanent contact pressure to the pipe wall and extreme mechanical stability, the FLUXUS® F808 is the most reliable ultrasonic clamp-on flowmeter available.
Not only is the FLUXUS® F808 rugged and reliable, it is precise. Thanks to carefully matched and temperature compensated transducers (fully ANSI / ASME compliant) the FLUXUS® F808 offers an unmatched low flow accuracy. Sophisticated digital signal processing within the flowmeter ensures for the most reliable, repeatable and accurate bi-directional flow measurement over a wide turndown ratio and temperature range.
Specifically Designed for Demanding Environments
Advantages_____________
- Bi-directional flow measurement over a wide turndown ratio
- Very cost effective: No pipe works No process shut-downs Virtually maintenance-free
- Matched, paired and wet flow calibrated (traceable certification)
- Excellent zero point stability and drift-free
- Independent of pipe size, material, operating pressure and medium
- High tolerance to entrained solids and gases
- Free of wear, tear and abrasion
- Not prone to clogging or corrosion
- No pressure loss or source of potential leaks
- Flow measurement at extreme temperatures from -170 °C up to 400 °C and beyond
Chemical Industry_____________
- Hazardous Organic and Inorganic Media- Acids and Caustics- Polymerization Processes- Infrastructural Processes
Hydrocarbon Products Handling_____________
- Pipeline Monitoring- Allocation Terminals
Crude Oil Refining_____________
- Atmospheric Distillation - Vacuum Distillation- Cracking Units
Oil Exploration On- & Offshore_____________
- FWKO and Separator Outlet- Coalescers- Scrubbers and Reboilers- Produced Water Injection- Chemical Injection
From Exploration and Production to Petrochemical and Chemical ProcessingFrom wellhead to refinery, the flows of crude oil and refined products need to be measured every step of the way. Harsh environments with corrosive atmospheres offshore or hot and dirty applications during crude oil refining require tough solutions.
Also during chemical processing, media such as acids, caustics or highly viscous organic substances place enormous material and mechanical stress upon wetted flow measurement technologies.
FLEXIM offers the better alternative: Being non-intrusive, the measurement system never gets into contact with the media inside the pipe – plant shut-downs for installation are a thing of the past.
The measurement system can never be the cause for a potential pipe leak, cannot be prone to clogging and is virtually maintenance-free.
Suitable for all pipe sizes from 10 mm (3/8 inch) diameter upwards - also no limitation on pipe material and wall thickness.
Providing exceptional reliability and accuracy at high and low flows due to matched transducer pairs and sophisticated internal signal processing.
FLEXIM’s permanently installed and portable flowmeters for explosive and hazardous areas have already been proven worldwide in many demanding applications with major operators.
FLUXUS® F808 IECEx / ATEX Zone 1 certified The rugged FLUXUS® F808 with its flameproof housing and stainless steel (SS316 optional) corrosion resistant transducers is suited for every industrial application – not only offshore. With the connection and electronic compartment being hermetically sealed, the FLUXUS® F808 provides for maximum operational safety, being IECEx / ATEX Zone 1 certified.
Because of the extremely robust transducers and the VARIOFIX mounting fixture, which ensures a permanent contact pressure to the pipe wall and extreme mechanical stability, the FLUXUS® F808 is the most reliable ultrasonic clamp-on flowmeter available.
Not only is the FLUXUS® F808 rugged and reliable, it is precise. Thanks to carefully matched and temperature compensated transducers (fully ANSI / ASME compliant) the FLUXUS® F808 offers an unmatched low flow accuracy. Sophisticated digital signal processing within the flowmeter ensures for the most reliable, repeatable and accurate bi-directional flow measurement over a wide turndown ratio and temperature range.
Non-Intrusive Ultrasonic Clamp-on Flow Measurement for Hazardous Areas
FLUXUS® F808 IECEx / ATEX Zone 1 certified
FLEXIM
FLUXUS® F808 IECEx / ATEX Zone 1 certified
FLUXUS® F808 Non-intrusive ultrasonic clamp-on flowmeter for liquids (clamp-on flow measurement according to the transit time difference method - automatic NoiseTrek selection for measurements with high gas or solid content)
Operating temperature of the transmitter:
-40 °C to +60 °C
Physical quantities: volumetric flow rate, mass flow rate, flow velocity
Degree of protection Transmitter(acc. to IEC / EN 60529:
IP66 (corrosion resistant coating - applicable for usage Offshore)
Flow velocity range: 0.01 to 25 m/s
Temperature range (at pipe wall):
-40 °C to +200 °C (-170 °C up to 400 °C and beyond with the WaveInjector mounting fixture)
Pipe diameter range: 10 mm up to 6.5 m
Repeatability: 0.15% of reading ± 0.01 m/s
Accuracy*: ± 0.5% of reading ± 0.01 m/s with field calibration** ± 1.2% of reading ± 0.01 m/s with advanced calibration (optional) ± 1.6% of reading ± 0.01 m/s with standard calibration
Data logger capacity: >100 000 measured values
Loggable values: all physical quantities, totalized values and diagnostic values
Outputs: 1 current output and 1 binary output or 1 current output and Modbus
Communication interface:
RS485, Modbus
Power supply: 100 to 240 V / 50 to 60 Hz or 20 to 32 V DC
Extreme Temperature WaveInjector Mounting Fixture
Rugged VARIOFIX L Mounting Fixture
Technical Data
Chemical Industries______
Petrochemical Industries______
Downstream - Refining______
Midstream - Hydrocarbon Transport ______
E&P - Offshore / Onshore
BU
F808
V2-
1EN
20
13/0
5 S
ubje
ct to
cha
nge
with
out n
otifi
catio
n
FLEXIM GmbH Berlin, GermanyPhone: +49 30 93 66 76 60 Fax: +49 30 93 66 76 80 [email protected] www.flexim.com
FLEXIM Instruments Asia Pte Ltd. SingaporePhone: +65 67 94 53 25 Fax: +65 68 62 28 36 [email protected] www.flexim.com
FLEXIM Instruments China Shanghai, ChinaPhone: +86 21 64 95 75 20 Fax: +86 21 64 95 75 90 [email protected] www.flexim.cn
* under reference conditions and with v > 0.15 m/s** if reference uncertainty better than < 0.2%
Further information can be found in the according F808 Technical Specifications at www.flexim.com
ATEX `, IECEx
