664min100 max605mm

min

58m

ax41

0mm

203

28052R

Flat TV Screen Wall Mount 32 - 60” - Adjustable Tilt

Main Features

USER GUIDE•TVSizeRange:32-60”•MaximumWeightCapacity:75kg•MountFunction:AdjustableTilt•WalltoTVDistance:45mm•CompatiblewithVESASizes:100x100/200x100/200x200 300x200/300x300/400x300/400x400/600x200and 600x400

•UniversalMountingSize:605x410mmMax.HolePattern

•We have not supplied wall fixings with this product. All walls differ in strength and thickness. Consult a qualified installer or seek advice from your local DIY/hardware store on purchasing suitable wall fixings to safely mount the bracket on the type of wall being used.•Check the contents list and images below to check there are no missing or defective parts. •Never exceed the Maximum Weight Capacity shown above.•Read these instructions carefully before installation. If in any doubt about safely installing this product, contact a professional installer for assistance.•This product was designed to be installed on wood stud walls and solid concrete/brick walls. When fixing to walls screws/bolts should be fixed into bricks/stone not into mortar courses.

•Make sure the wall will support the combined load of the equipment and hardware. Also check for hidden wiring or plumbing. •Make sure that the heads of the screws/bolts you buy as wall fastenings are the correct size to hold the bracket securely in position. •For larger/heavier TVs we recommend that you ask someone to assist you with lifting and positioning your TV.•This product is suitable for indoor use only. •Improper installation or use of this product can result in product failure, damage or personal injury. •This product contains small items that could cause choking if swallowed, so keep these items away from children and pets. •Appropriate safety equipment and proper tools must be used for installation. Always check manufacturer’s operating and safety instructions before using tools and other equipment

WARNING

Components

M5 x 12 4pcs

M4 x 30 4pcs

Wall Mount & VESA Compatibility• VESAisthestandardadoptedbymostTVmanufacturersforwall bracket mounting.

• Thereare4holesonthebackofeveryflatscreenTVandthe spacebetweentheholesisgovernedbytheVESAstandard.

• VESAcomesinarangeofsizesdependingontheweightandsize oftheflatscreenTV;sizes100x100mm,100x200mmandsoon...are standard.NotallflatscreenTVsarecompliant,contacttheTV manufacturer for assistance if your TV does not appear to comply with VESA.

• TocheckifyourTVormonitoriscompliant,lookattherearof thedisplaythereshouldbe4screw-holesinasquarepatternor inlargerdisplaysarectangularshape.SeeFig.2opposite,with VESAmountingpointsshowninwhitecircles.

• Measurethedistancesmarked(2)(horizontal)x(1)(vertical)in mmtofindyourVESAformat.

Fig. 2

Before installation check that you have all the components shown here and that none of them is damaged.

Please Note wall fixings are not supplied with this product.

M8 x 25 4pcs

M6 x 30 4pcs

M8 x 40 4pcs

M4/M5/M6/M8Washer 4pcs

Small Plastic Spacers 4pcs

1

2

3

7

8

9

10

Wall Plate 1pc

Fig. 1

M4 x 12 4pcs M5 x 30 4pcs

4

5

6

M6 x 12 4pcs

Large Plastic Spacers 4pcs

11

12

TV Rail 2pcsInc. Safety Screw

13

14

FixingtoWood(StudWalls)Use a good quality stud sensor to locate adjacent upright studs in the areawhereyouwanttomountyourscreen(thecentresofeachstudisusuallyapprox.400mmor600mmapart).Itisagoodideatoverifywherethe studs are located with an awl or thin nail as shown in Fig. 3. The wall plate 13 is attached to the wall using a minimum of four appropriate screws/bolts and washers as shown in Fig.4. Make sure the screws/bolts are suitable for wood and large enough to support the weightoftheTVandbracket(ifindoubtaskforadviceatyourlocalDIY/hardware store and remember to make sure that the heads of the screws/boltsarethecorrectsizetoholdthebracketsecurelyinposition).Mark and drill your first hole into the wood as close as possible to the centre of an upright. To mark the remaining hole/holes, hold the wall plate 13 to the wall, using the spirit level bubble to make sure the wall plate is level, and mark the centre of each hole. Make sure the wall plate is oriented so that the spirit level bubble is facing towards you and all screws/bolts are properly tightened. FixingtoConcrete/BrickWallsTheprocessisthesameasforattachingtowood.Youshouldhoweveruseaminimumof6screws/bolts,washersandwallplugssuitableforthetypeofwallyouaremountingonto(ifindoubtaskforadviceatyourlocalDIY/hard-ware store and remember to make sure that the heads of the screws/bolts are the correct size to hold the wall plate 13 securelyinposition),seeFig.5&6. When fixing to walls screws/bolts should be fixed into bricks/stone not into mortar courses. Use the wall plate 13 as a template to mark screw/bolt positions and make sure all screws/bolts are properly tightened.

Step2Make sure the two TV Rails 12 are mounted at an equal distance from the top of the TV and as close to the center vertically as possible, see Fig. 7.FoureachoftwolengthsofM4,M5,M6andM8mountingboltsare provided ➊➋➌➍➎➏➐➑forattachingtheTVrailstotheVESAmounting holes use the size which fits your TV. Use longer lengths and Plastic Spacers10 or 11 for TV’s with curved or recessed back panels as shown in Fig.7.Ifyouaremountingtoatelevisionwithaflatbackyoucanuseashorterboltandwillnotneedaplasticspacer,seeFig.8.ForM4andM5 bolts use the smaller aperture in the washer and the small spacer 10 for M6andM8boltsusethelargerapertureandlargespacer11 . Make sure all four bolts are fully tightened.

With the help of another person, hook the TV Rails 12 with the TV attached over the top of the Wall Plate 13 ,seeFig.9&10.DonotreleasetheTVuntilthe mounting arms have been securely hooked onto the wall plate 13 . Then tighten the safety screws 14 as shown in Fig. 9.

PLEASE NOTE: For larger/heavier TVs we recommend that you ask someone to assist you with lifting and positioning your TV.

©PhilexElectronicLtd.2012.V1.2

STEP 3 - Hanging and securing the TV

Mounting your TV - Overview

Once you have decided where to locate your TV and where the bracket needs to be positioned, mounting requires the 3 steps described below. Step 1: mark and drill fixing holes in the wall and attach the wall plate ➓to the wall using suitable screws/bolts. Step 2 attach the TV Rails 12 to the back of the TV using the plastic spacers 10 or 11 if required. Step 3 hang the TV Rails 12 and TV onto the wall plate 13 and tighten the safety screws to hold the TV arms in position.

STEP 2 - Attaching the TV Rails to the TV

STEP 1 - Fixing the Wall Plate to the Wall

Fig. 3

Fig. 4

Fig. 12

14

Fig. 10Fig. 9

12

13

Back of TV

12

12

10 11or

Fig. 7TV with recessed back panel

Fig. 8TV with flat back panel

13

TV Front

Fig. 5

Fig. 6

Tilt Adjust Knob

10 1211

For further information or any queries please contact our Customer Careline: 08457 573 479 (Localrate–UKonly)Technical Support: www.philex.com/support