Flanged with Opposite Side Support Installation Instructions
description
Transcript of Flanged with Opposite Side Support Installation Instructions
![Page 1: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/1.jpg)
Flanged with Opposite Side Support Installation InstructionsQuick Installation Guide00825-0200-4809 rev. DB – 48500825-0100-4585 rev. AA – 585
![Page 2: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/2.jpg)
Mark the Locations for Drilling the Mounting Holes Mark the location for the first hole Use a pipe tape to find and mark the location of
the opposite side hole
![Page 3: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/3.jpg)
Drill the Holes into the Pipe Using a Drill Bit or Hole Saw
Tag with correct drill hole size attached to the Annubar
The mounting holes must be 180° degrees apart to ensure
![Page 4: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/4.jpg)
Hole Sizes for Each Annubar Type485
585
![Page 5: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/5.jpg)
Clean the Area with a Grinder to Prepare for the Surface for Welding
![Page 6: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/6.jpg)
Mounting Should be Welded So the Bolt Holes Straddle Pipe Center Line The mounting
hardware should be gapped 1/16th inch for welding– Use weld rod to do this
It should also be centered over the drilled hole
![Page 7: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/7.jpg)
Tack Weld the Mounting Hardware with 4 Equal Length Tacks Tack weld anywhere on
the mounting hardware Then again directly across
from the first tack weld Then on the other 2 sides
2
1
3
![Page 8: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/8.jpg)
Check to See that the Mounting Hardware is Level and Square If it’s not, use a
rubber mallet to lightly adjust the hardware and recheck
![Page 9: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/9.jpg)
Verify that the ODF Dimension Matches What is Listed in the QIG The ODF is the dimension from outside pipe diameter to face of flange
485 585
![Page 10: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/10.jpg)
Verify that the ODF Dimension Matches What is Listed in the QIG The ODF is the dimension from outside pipe diameter to face of flange
![Page 11: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/11.jpg)
Complete a Continuous Weld Around the Perimeter of the Unit
![Page 12: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/12.jpg)
Insert the Annubar Sensor to Align the Opposite Side Support (OSS)
Round tip of the Annubar
Sockolet or threadolet
Welded or threaded OSS Plug
The tip of the Annubar should engage the OSS Support Plug a minimum of ½ inch
![Page 13: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/13.jpg)
Gap the Threadolet or Sockolet 1/16” and tack weld it into place With the Annubar
inside
![Page 14: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/14.jpg)
Remove the Annubar and Complete a Continuous Weld Around the Sockolet or Threadolet
![Page 15: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/15.jpg)
Weld or Thread the Opposite Side Support Plug
Insert the OSS Plug into the Sockolet, then gap it 1/16” (provides socket weld gap) and tack weld it in place. Then complete a continuous weld around the OSS Plug.
Welded OSSThreaded OSS
The Annubar Sensor should not be installed for this step (This would cause irreparable damage to the Annubar)
First wrap the threads with the appropriate tape sealant. Then thread the OSS Plug into the threadolet.
![Page 16: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/16.jpg)
Insert the Annubar With the appropriate gasket Verify the flow arrow on the side of the Annubar
is pointing in the right direction
![Page 17: Flanged with Opposite Side Support Installation Instructions](https://reader035.fdocuments.net/reader035/viewer/2022081502/56816312550346895dd38ac2/html5/thumbnails/17.jpg)
Tighten the Bolts in a Cross Pattern to Appropriate Torque Specification