Fixed Network Camera Hardware User This section describes the procedures in installing the camera on

download Fixed Network Camera Hardware User This section describes the procedures in installing the camera on

of 32

  • date post

    26-Sep-2020
  • Category

    Documents

  • view

    0
  • download

    0

Embed Size (px)

Transcript of Fixed Network Camera Hardware User This section describes the procedures in installing the camera on

  • Fixed Network Camera

    Hardware User Manual

    FCS-3056, FCS-3064

    Ver.2014/04/02

  • Hardware Manual

    2

    Table of Contents

    Precautions ............................................................. 4

    Safety Instructions .................................................................................... 6

    Introduction ............................................................. 7

    The List of Models ..................................................................................... 7

    Package Contents ...................................................................................... 7

    Physical Description ................................................................................. 8

    Before Installation................................................. 10

    How to Connect DI/Do Devices ............................................................... 10

    How to Connect Audio Devices .............................................................. 13

    Installing the Camera on a Surface ..................... 14

    Step 1: Drill the Holes .............................................................................. 14

    Step 2: Open the Dome Cover ................................................................ 15

    Step 3: Install the Camera to the Surface .............................................. 16

    Step 4: Connect the Cable ...................................................................... 17

    Step 5: Access the Camera Live View .................................................... 18

    Step 6: Adjust the Viewing Angle and Focus ........................................ 18

    Step 7: Close the Dome Cover ................................................................ 18

    Other Adjustments and Accessories .................. 20

    How to Adjust the Camera Viewing Angle and Focus .......................... 20

    FCS-3064 Camera Models ................................................................... 20

  • Hardware Manual

    3

    How to Replace the Dome Cover ............................................................ 21

    How to Use a Memory Card .................................................................... 25

    How to Insert the Memory Card ............................................................ 25

    How to Remove the Memory Card ........................................................ 25

    Accessing the Camera ......................................... 26

    Configure the IP Addresses .................................................................... 26

    Access the Camera .................................................................................. 30

  • Hardware Manual

    4

    Precautions

    Read these instructions

    You should read all the safety and operating instructions before using this product.

    Heed all warnings

    You must adhere to all the warnings on the product and in the instruction manual. Failure to follow

    the safety instruction given may directly endanger people, cause damage to the system or to

    other equipment.

    Servicing

    Do not attempt to service this video device yourself as opening or removing covers may expose

    you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

    Trademarks

    All names used in this manual are probably registered trademarks of respective companies.

    Liability

    Every reasonable care has been taken during the writing of this manual. Please inform your local

    office if you find any inaccuracies or omissions. We cannot be held responsible for any

    typographical or technical errors and reserve the right to make changes to the product and

    manuals without prior notice.

  • Hardware Manual

    5

    Federal Communications Commission Statement

    This equipment has been tested and found to comply with the limits for a class B

    digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

    to provide reasonable protection against harmful interference in a residential

    installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

    installed and used in accordance with the instructions, may cause harmful interference to radio

    communications. However, there is no guarantee that interference will not occur in a particular

    installation. If this equipment does cause harmful interference to radio or television reception,

    which can be determined by turning the equipment off and on, the user is encouraged to try to

    correct the interference by one or more of the following measures:

     Reorient or relocate the receiving antenna.

     Increase the separation between the equipment and receiver.

     Connect the equipment into an outlet on a circuit different from that to which the

    receiver is connected.

     Consult the dealer or an experienced radio/TV technician for help.

    Warning: Changes or modifications to the equipment that are not expressly approved by the

    responsible party for compliance could void the user’s authority to operate the equipment.

    European Community Compliance Statement

    This product has been tested and found to comply with the limits for Class B

    Information Technology Equipment according to European Standard EN 55022

    and EN 55024. In a domestic environment, this product may cause radio interference in which

    cause the user may be required to take adequate measures.

  • Hardware Manual

    6

    Safety Instructions

    Cleaning

    Disconnect this video product from the power supply before cleaning.

    Attachments

    Do not use attachments not recommended by the video product manufacturer as they may cause

    hazards.

    Do not use accessories not recommended by the manufacturer

    Only install this device in a dry place protected from weather

    Servicing

    Do not attempt to service this video product yourself. Refer all servicing to qualified service

    personnel.

    Damage Requiring service

    Disconnect this video product from the power supply immediately and refer servicing to qualified

    service personnel under the following conditions.

    1) When the power-supply cord or plug is damaged

    2) If liquid has been spilled, or objects have fallen into the video product.

    3) If the inner parts of video product have been directly exposed to rain or water.

    4) If the video product does not operate normally by following the operating Instructions in this

    manual. Adjust only those controls that are covered by the instruction manual, as an improper

    adjustment of other controls may result in damage, and will often require extensive work by a

    qualified technician to restore the video product to its normal operation.

    Safety Check

    Upon completion of any service or repairs to this video product, ask the service technician to

    perform safety checks to determine if the video product is in proper operating condition.

  • Hardware Manual

    7

    Introduction

    The List of Models

    This hardware manual contains the following models:

    FCS-3056

    Fixed Dome Network Camera, 5-Megapixel, PoE 802.3af, Day & Night,

    IR LEDs

    FCS-3064

    Fixed Dome Network Camera, 5-Megapixel, PoE 802.3af, Day & Night,

    IR LEDs, WDR

    From the installation perspective these models are very similar; therefore you can use one

    manual for all of them.

    Package Contents

    Camera Mounting Screw Kit Hexagon Screwdriver

    Terminal Block (for Audio and DI/DO)

    Drill Template Quick Installation Guide

    Drill Template

  • Hardware Manual

    8

    Physical Description

    FCS-3056, FCS-3064

    NOTE: Actual camera may slightly differ.

    1) Ethernet Port

    Connects to a network using an Ethernet cable.

    2) Memory Card Slot

    Insert a memory card into this slot for local recording purposes. See How to Use a Memory Card

    on page 25 for more information.

    NOTE: Supports microSDHC and microSDXC cards.

    3) Reset Button

    The purpose of reset button is to restore the factory default settings of the camera, including

    the administrator’s password.

    The reset button can be used for following purposes:

    The administrator’s password has been forgotten and therefore the camera cannot be

    accessed.

    1. In case of IP address, mask, or allow/deny filter related issues, resulting with inability to

    modify these settings.

    2. In case of connectivity issues or abnormal video quality.

  • Hardware Manual

    9

    How to do the reset properly?

    Press and hold the reset button for 5 seconds.

    4) Digital Input / Output (DI/DO) and Audio Input / Output

    This connector connects to digital input or output devices, such as an alarm trigger, panic

    button, etc., as well as audio input and output devices, such as microphones and speakers.

    Digital Input (DI) and Digital Output (DO) devices ar