Files 2 handouts-ch02
-
Upload
francisco-rodriguez-milton-jimenez -
Category
Design
-
view
615 -
download
5
Transcript of Files 2 handouts-ch02
©2005 Pearson Education South Asia Pte Ltd
2. Strain
1
CHAPTER OBJECTIVES• Define concept of
normal strain• Define concept of
shear strain• Determine normal
and shear strain in engineering applications
©2005 Pearson Education South Asia Pte Ltd
2. Strain
2
CHAPTER OUTLINE
1. Deformation2. Strain
©2005 Pearson Education South Asia Pte Ltd
2. Strain
3
Deformation• Occurs when a force is applied to a body• Can be highly visible or practically unnoticeable• Can also occur when temperature of a body is
changed• Is not uniform throughout a body’s volume, thus
change in geometry of any line segment within body may vary along its length
2.1 DEFORMATION
©2005 Pearson Education South Asia Pte Ltd
2. Strain
4
To simplify study of deformation• Assume lines to be very short and located in
neighborhood of a point, and• Take into account the orientation of the line
segment at the point
2.1 DEFORMATION
©2005 Pearson Education South Asia Pte Ltd
2. Strain
5
Normal strain• Defined as the elongation or contraction of a line
segment per unit of length• Consider line AB in figure below• After deformation, Δs changes to Δs’
2.2 STRAIN
©2005 Pearson Education South Asia Pte Ltd
2. Strain
6
Normal strain• Defining average normal strain using εavg (epsilon)
• As Δs → 0, Δs’ → 0
2.2 STRAIN
εavg = Δs − Δs’Δs
ε = Δs − Δs’Δs
limB→A along n
©2005 Pearson Education South Asia Pte Ltd
2. Strain
7
Normal strain• If normal strain ε is known, use the equation to
obtain approx. final length of a short line segment in direction of n after deformation.
• Hence, when ε is positive, initial line will elongate, if ε is negative, the line contracts
2.2 STRAIN
Δs’ ≈ (1 + ε) Δs
©2005 Pearson Education South Asia Pte Ltd
2. Strain
8
2.2 STRAINUnits • Normal strain is a dimensionless quantity, as
it’s a ratio of two lengths• But common practice to state it in terms of
meters/meter (m/m)• ε is small for most engineering applications, so
is normally expressed as micrometers per meter (μm/m) where 1 μm = 10−6
• Also expressed as a percentage, e.g., 0.001 m/m = 0.1 %
©2005 Pearson Education South Asia Pte Ltd
2. Strain
9
2.2 STRAINShear strain• Defined as the change in angle that occurs
between two line segments that were originally perpendicular to one another
• This angle is denoted by γ (gamma) and measured in radians (rad).
©2005 Pearson Education South Asia Pte Ltd
2. Strain
10
2.2 STRAINShear strain• Consider line segments AB and AC originating
from same point A in a body, and directed along the perpendicular n and t axes
• After deformation, lines become curves, such that angle between them at A is θ’
©2005 Pearson Education South Asia Pte Ltd
2. Strain
11
2.2 STRAINShear strain• Hence, shear strain at point A associated with n
and t axes is
• If θ’ is smaller than π/2, shear strain is positive,otherwise, shear strain is negative
γnt =π2
limB→A along nC →A along t
θ’−
©2005 Pearson Education South Asia Pte Ltd
2. Strain
12
Cartesian strain components• Using above definitions of normal and shear strain,
we show how they describe the deformation of the body
2.2 STRAIN
• Divide body into small elements with undeformed dimensions of Δx, Δy and Δz
©2005 Pearson Education South Asia Pte Ltd
2. Strain
13
Cartesian strain components• Since element is very small, deformed shape of
element is a parallelepiped
• Approx. lengths of sides of parallelepiped are
(1 + εx) Δx (1 + εy)Δy (1 + εz)Δz
2.2 STRAIN
©2005 Pearson Education South Asia Pte Ltd
2. Strain
14
Cartesian strain components• Approx. angles between the sides are
2.2 STRAIN
π2 − γxy
π2 − γyz
π2 − γxz
• Normal strains cause a change in its volume• Shear strains cause a change in its shape• To summarize, state of strain at a point requires
specifying 3 normal strains; εx, εy, εz and 3 shear strains of γxy, γyz, γxz
©2005 Pearson Education South Asia Pte Ltd
2. Strain
15
Small strain analysis• Most engineering design involves applications
for which only small deformations are allowed• We’ll assume that deformations that take place
within a body are almost infinitesimal, so normal strains occurring within material are very smallcompared to 1, i.e., ε << 1.
2.2 STRAIN
©2005 Pearson Education South Asia Pte Ltd
2. Strain
16
Small strain analysis• This assumption is widely applied in practical
engineering problems, and is referred to as small strain analysis
• E.g., it can be used to approximate sin θ = θ, cos θ = θ and tan θ = θ, provided θ is small
2.2 STRAIN
©2005 Pearson Education South Asia Pte Ltd
2. Strain
17
EXAMPLE 2.1
Rod below is subjected to temperature increase along its axis, creating a normal strain of εz = 40(10−3)z1/2, where z is given in meters.Determine (a) displacement of end B of rod due to temperature increase, (b) average normal strain in the rod.
©2005 Pearson Education South Asia Pte Ltd
2. Strain
18
EXAMPLE 2.1 (SOLN)
(a) Since normal strain reported at each point along the rod, a differential segment dz, located at position z has a deformed length:
dz’ = [1 + 40(10−3)z1/2] dz
©2005 Pearson Education South Asia Pte Ltd
2. Strain
19
EXAMPLE 2.1 (SOLN)
(a) Sum total of these segments along axis yields deformed length of the rod, i.e.,z’ = ∫0 [1 + 40(10−3)z1/2] dz
= z + 40(10−3)(⅔ z3/2)|0= 0.20239 m
0.2 m
0.2 m
Displacement of end of rod isΔB = 0.20239 m − 0.2 m = 2.39 mm ↓
©2005 Pearson Education South Asia Pte Ltd
2. Strain
20
EXAMPLE 2.1 (SOLN)
(b) Assume rod or “line segment” has original length of 200 mm and a change in length of 2.39 mm. Hence,
εavg = Δs’ − ΔsΔs
= 2.39 mm200 mm
= 0.0119 mm/mm
©2005 Pearson Education South Asia Pte Ltd
2. Strain
21
EXAMPLE 2.3
Plate is deformed as shown in figure. In this deformed shape, horizontal lines on the on plate remain horizontal and do not change their length.Determine (a) average normal strain
along side AB, (b) average shear strain
in the plate relative to x and y axes
©2005 Pearson Education South Asia Pte Ltd
2. Strain
22
EXAMPLE 2.3 (SOLN)
(a) Line AB, coincident with y axis, becomes line AB’ after deformation. Length of line AB’ isAB’ = √ (250 − 2)2 + (3)2 = 248.018 mm
©2005 Pearson Education South Asia Pte Ltd
2. Strain
23
EXAMPLE 2.3 (SOLN)
(a) Therefore, average normal strain for AB is,
= −7.93(10−3) mm/mm
(εAB)avg = ABAB’ − AB 248.018 mm − 250 mm
250 mm=
Negative sign means strain causes a contraction of AB.
©2005 Pearson Education South Asia Pte Ltd
2. Strain
24
EXAMPLE 2.3 (SOLN)
(b) Due to displacement of B to B’, angle BAC referenced from x, y axes changes to θ’. Since γxy = π/2 − θ’, thus
γxy = tan−1 3 mm250 mm − 2 mm = 0.0121 rad( )
©2005 Pearson Education South Asia Pte Ltd
2. Strain
25
CHAPTER REVIEW
• Loads cause bodies to deform, thus points in the body will undergo displacements or changes in position
• Normal strain is a measure of elongation or contraction of small line segment in the body
• Shear strain is a measure of the change in angle that occurs between two small line segments that are originally perpendicular to each other
©2005 Pearson Education South Asia Pte Ltd
2. Strain
26
CHAPTER REVIEW
• State of strain at a point is described by six strain components:
a) Three normal strains: εx, εy, εz
b) Three shear strains: γxy, γxz, γyz
c) These components depend upon the orientation of the line segments and their location in the body
• Strain is a geometrical quantity measured by experimental techniques. Stress in body is then determined from material property relations
©2005 Pearson Education South Asia Pte Ltd
2. Strain
27
CHAPTER REVIEW
• Most engineering materials undergo small deformations, so normal strain ε << 1. This assumption of “small strain analysis” allows us to simplify calculations for normal strain, since first-order approximations can be made about their size