FiberLase CO2 Fiber & AcuPulse 40WG CO2...
Transcript of FiberLase CO2 Fiber & AcuPulse 40WG CO2...
-
www.lumenis.com | www.surgical.lumenis.com
FiberLase CO2 Fiber & AcuPulse 40WG
FiberLase™ CO2 Fiber & AcuPulse™ 40WG CO2 Laser
PERFORMANCE AND FLEXIBILITY COMBINED
-
• Higher power CO2 fiber
• Aiming beam emits at fiber tip
• Exceptional fiber durability
• Enhanced clinical access
• Variety of hand-pieces and accessories for multiple applications
Performance WHERE YOU NEED IT
-
FiberLase CO2 Fiber & AcuPulse 40WG Expanding the reach of CO2 laser surgery
FEATURES BENEFITS
Up to 40 Watts fiber Higher output & faster input power treatments
Aiming beam Enhances ability to target tissue
Low beam divergence Precise & consistent tissue effect
2 meter long CO2 fiber Increased mobility with renew capability
Renew distal tip of fiber Fiber continues working during procedure throughout procedure resulting in less cost
Fiber support guide & Allows for efficient handpiece support arm OR set-up
Optional internal purge Convenience & air supply cost-savings
Select from a wide range of hand pieces available for various procedures.
-
©2010, the Lumenis Group of Companies. All rights reserved. Lumenis, its logo, AcuPulse and FiberLase are trademarks or registered trademarks of the Lumenis Group of Companies. Specifications are subject to change without notice. Printed in the U.S.A. For distribution in the U.S.A only.
PB-1083990 Rev. A
FiberLase CO2 Fiber & AcuPulse 40WG
320µ 400µ 485µ 570µ 1153µ 1570µ
Spot diameter
0mm 1mm 2mm 3mm 10mm 15mm
Other 2
320µ 375µ 430µ 485µ 870µ 1145µ
Spot diameter
Lumenis1
1 1.26 1.39 1.48 1.74 1.86Power density ratio
Quality Beam PerformanceGreater power with less beam divergence allows for accuracy at greater distances
AcuPulse 40WG CO2 Laser Technical Specifications
Part Number GA-0000140
Laser Type CO2 Laser, sealed-off, DC excited
Wavelength 10.6 micron, infrared
Mode Structure TEMoo
Laser Operating Modes Continuous Wave (CW), Pulser, SuperPulse
CW Power 1 - 40 W
SuperPulse Average Power 0.5 - 15 W
Pulser Average Power 1 - 35 W
Tissue Exposure Modes
Type Power (W) On time (sec) Off time (sec)
Continuous 1.0 - 4.55.0 - 40 NA NA
Single Pulse 1.0 - 4.55.0 - 400.05 - 1.000.01 - 1.00 NA
Repeat Pulse 1.0 - 4.5 5.0 - 400.05 - 1.000.01 - 1.00
0.01 - 1.000.01 - 1.00
Controls Multi-color, high resolution touch panel & footswitch
Aiming Beam Up to 5mW red diode laser, 635 nm, adjustable intensity, blink on/off
Beam Delivery Lumenis FiberLase CO2 fiber
Memory Settings 100 + custom memory setting capacity
Laser System Cooling Self-contained, closed cycle
CO2 Fiber Cooling Self-contained internal air pump or option of external pressurized purge gas
Electrical 100 – 240 VAC, 10 A, 50/60 Hz
Dimensions 35 cm W x 40 cm D x 119 cm H; (14.6” W x 15.8” x 47” H)
Weight 49 kg (110 lbs)
Standards CE, UL
FiberLase CO2 Fiber, Single-use disposable
Specifications 2 meter long, 1.04mm outside diameter, 500µm inside diameter
Spot Size 320µm at fiber output
1 Internal test Rpt – R&D PH-SB-201 Rev.0. 2 Other fiber manufacturer’s reported beam divergence numbers
VISIBLE AND INVISIBLELASER RADIATION
Avoid eye or skin exposureTo direct or scattered radiation.
LASER SURGERY IN PROGRESSSAFETY EYEWEAR REQUIRED
40 Watts ContinuousCO LASER/10600nm
LB-1024830 Rev_0
CLASS 3A/IIIa LASER
CLASS 4/IV LASER5 mWatts ContinuousDiode LASER/635nm
2