DUPLEX DOMESTIC WATER PUMPS

42 CROSBY ST 221000221000-01-0E.M.02.19.15

TRITON NOTE; ENGINEER, PLEASE PROVIDE INFORMATION REQUIRED ON PAGE 3 REGARDING PUMP SUCTION PRESSURE.

X

03-05-15 MS/BB

Electrical contractor to provide 40A, 3P circuit breaker and 4#8&1#10G-3/4"C in lieu of 20A, 3P and 4#12 & 1#12G-3/4"C shown on the design document

E. SHIPLEY 03/06/2015

SEE CONSULTANT COMMENTS

G. A. Fleet Associates, Inc..

Important:Drawings are not to scale, use dimensions shown. Do not fix foundation bolts rigidly until equipment is in place, since castings vary slightly in dimensions. Seismic restraints and or calculations are not provided unless specifically noted below.

G. A. Fleet Assoc., Inc. P. O. Box 616 Harrison, NY 10528 (914) 835 - 4000 Fax (914) 835 - 1331

Fleet Pump & Service (914) 835 - 3801 Fax (914) 835 - 2946

Sold To: Demar Plumbing Corp. 147 Attorney Street New York, NY 10002

Ship To: Demar Plumbing C/O 42 Crosby Street (Contractor to Confirm)

Engineer: Rodkin Cardinale PC Date: 1/21/15 Customer Order No. 300-378

System: Duplex Domestic Water Booster System Fleet Order No.

Marks: 42 Crosby Street Sheet: 1 Of: 2 By: R. DiLorenzo

Q T Y D E S C R I P T I O N

DUPLEX DOMESTIC WATER BOOSTER SYSTEM BP-1,2

1 - Factory pre-piped packaged Syncroflo system consisting of factory assembling, mounting and wiring of pumps, motors, VFD drives, valves and control panel on a common fabricated steel base suitable for grouting. System includes:

2 - Peerless Model C610A close-coupled end suction pumps, bronze fitted construction with mechanical seals. Each pump is rated for 80 GPM at 130 (56 PSIG) TDH when close coupled to a 7.5 HP, 208/3/60, 3500 RPM ODP motors with 1.15 SF.

2 - Thermal safety purge valves, field piped to drain.

2 - Combination pressure regulating and check valves.

4 - Pump isolation valves.

1 - Interconnecting piping and wiring. Headers are 3 304SS with flanged ends.

1 - Duplex control panel with: 2-circuit breaker disconnect switches, 2- magnetic across-the-line by-pass starters with three phase thermal overload protection, 2-VFD Nema 1 drives, 2-HOA selector switches, 2-pump running lights, 1-control circuit transformer, 1-automatic alternator with manual override, 2-pump failure alarm with light, 1-low suction level alarm (from Roof Tank Control Panel) with light, pump cut-off and automatic reset, 1-low system pressure alarm with light, 1-common audible alarm with silencing pushbutton, 4-auxiliary alarm contacts, all mounted and prewired in a NEMA-12 enclosure. Panel wired for two incoming power feeds and includes an automatic power transfer relay.

1 - Set of pressure gauges, pressure switches and controls for automatic operation.

1 - Differential pressure transmitters.

G. A. Fleet Associates, Inc..

Important:Drawings are not to scale, use dimensions shown. Do not fix foundation bolts rigidly until equipment is in place, since castings vary slightly in dimensions. Seismic restraints and or calculations are not provided unless specifically noted below.

G. A. Fleet Assoc., Inc. P. O. Box 616 Harrison, NY 10528 (914) 835 - 4000 Fax (914) 835 - 1331

Fleet Pump & Service (914) 835 - 3801 Fax (914) 835 - 2946

1 - Pre-charged hydropneumatic tank 132 gallon, 125 PSIG working pressure ASME (shipped loose), remote mounted. Contractor to make final connections and provide isolation and drain valves.

CONTRACTOR PLEASE NOTE:1. Inertia base not included, to be provided by others. 2. Control wiring by others 3. Vibration isolators, flexible connectors, di-electric fittings and by-pass piping to be

provided by the Contractors, as required. 4. Contractor to verify access and advise if the system needs to be fabricated for site

disassembly. 5. The unit will be built with a split base for ease of disassembly after unloading, by the

contractor and reassembly on site. Contractor to reassemble the package and replace sensing lines as required.

6. Please schedule equipment start-up two (2) weeks in advance, call Julia French 914-381-7921.

ENGINEER PLEASE CONFIRM / ADVISE: 1. Panel power feed arrangement, submitted as individual power feeds to each pump. 2. Tank location. 3. Suction Pressure: Minimum at the pump _______ PSIG Maximum in the street _______ PSIG

ENGINEER PLEASE PROVIDE INFORMATION

45 50

42 Crosby StreetProject :Quote No. : US-2722-137

Customer :

Fax :Phone :Date : Wednesday, January 21, 2015

Contact :

Demar Plumbing Corp.

Page No : 1

Type: C - End Suction Close Coupled General PurposePump Model: Nom. Speed: 3568 RPM, 60 Hz Electric

Peerless - C610A

Impeller Dia.: 5.62 inch

Impeller No.:

Curve No.: 3115001/ Viscosity: 1.0071.000

68 FWaterFluid:

Temperature:

Sp. Gravity:cSt

Item : 1

Market : WaterYour Ref. :

SeePtslist

Duty Flow

Duty Head

Imp. Dia.

Power Required

NPSH Required

Efficiency

80

130

5.62

4.7

5.1

57.2

US gpm

ft

inch

hp

ft

%

Peak Power 6 hp

Tolerance Hyd Inst-Peerless Std

Flow - US gpm20015010050

Pow

er-h

p

642

Hea

d-f

t

150

100

50 Effi

cien

cy-%

908070605040302010

D3

D1

D1-6.00 inch, D2-5.00 inch, D3-4.00 inch

NP

SH

-ft 15

10

5

CommentsPerf. curve represents typicalperf, vel. head is incld. Perf. curves tests are performed in accordance with H.I.Stds.

Closed Valve Head 137.7 ft

Flow(US gpm)

Head(ft)

Efficiency(%)

Power Required(hp)

NPSH Required(ft)

30.6 141.7 32.8 3.3 4.243.7 141.3 41.9 3.7 4.156.9 139.7 48.9 4.1 4.270.0 136.8 54.2 4.5 4.683.2 132.8 58.0 4.8 5.396.3 127.6 60.5 5.1 6.6

109.5 121.3 61.6 5.4 8.5122.7 114.0 61.5 5.7 11.1135.8 105.6 60.2 6.0 14.6

Grundfos - RAPID v8.25.9.1 (Windows 7) - 06th March 2012.

ALL

DIM

ENSI

ON

S +

/- TO

LER

ANCE

OF

1/2"

DWG

NO.

12"

CHK.

BY

:

Pu

mp

ing

Sy

ste

mS

olu

tio

ns

ENG

. BY

: AC

D

PR

OP

RIE

TA

RY

DR

AW

ING

TH

IS

CO

NF

IDE

NT

IAL

DO

CU

ME

NT

IS

TH

E

PR

OP

ER

TY

OF

NO

RC

RO

SS

,

GE

OR

GIA

NO

T

TO

BE

DU

PLI

CA

TE

D

WIT

HO

UT

WR

ITT

EN

PE

RM

ISS

ION

OR

US

ED

IN

AN

Y

WA

Y

DE

TR

IME

NT

AL

TO

TH

E

CO

MP

AN

Y.

1 1/

2"

TYP.

(38m

m)

1 1/

2"

TYP.

(38m

m)

44" (

1118

mm

)

P27-

705-

4V

DAT

E:

6/11

/200

3D

RAW

N BY

: AC

D

DIM

ENSI

ON

AL

KEY

43

31 2

4 43

KEY

HEAD

ERSI

ZEM

OTO

RFR

AME

SIZE

BWD

OW 57

"

1448

mm

143

-

215J

M

254

-

256J

M

143

- 215

JM

40"

1016

mm

40"

1016

mm

45"

1143

mm

45"

1143

mm

254

- 286

JM

42"

1067

mm

47"

1194

mm

42

1/2"

1080

mm

47

1/2"

1207

mm

51"

1295

mm

52"

1321

mm

58"

1473

mm

BWD

OW

(MAX

)

DUPL

EX

HORI

ZONT

AL

IRO

NHEA

RTST

AINL

ESS

STEE

L W

ITH

VFD'

s &

CHEC

K VA

LVES

24"

(610m

m)

66" (

1676

mm

)

NO

TES:

CER

TIFI

ED.

OSH

A R

EGUL

ATIO

NS

AND

FEDE

RAL

REG

ULAT

ION

29

CFR

1910

.39

9.

THE

ENTI

RE

PACK

AGED

SYST

EM

IS

THIR

D

PART

Y

SYN

CRO

FLO

PACK

AGED

PUM

PING

SYST

EMS

COM

PLY

WIT

H

REV.

DESC

RIP

TIO

N

ARE

VISE

D

HEAD

ERS

DAT

E

ER02

/16/

04

(NFPA-70) SECTION 110

EXCEPT AS NOTED PER NEC

36" MIN. CLEARANCE REQ'D.

10

1/2"

(267m

m)

1.

ALL

DIM

ENSI

ONS

SUBJ

ECT

TO C

HANG

E W

ITH

OUT

NO

TICE

.

2. P

URG

E VA

LVE

DRAI

N LI

NE

TO

BE P

IPED

TO

FLO

OR

DRA

IN IN

PRO

XIM

ITY

OF

BOO

STER

SYS

TEM

(BY

OTH

ERS)

.

3.

SEE

DATA

SYST

EM

SHEE

T FO

R L/

H O

R R/

H H

EAD

ERS

ENTR

Y/EX

IT C

ONN

ECTI

ON

SEE

CON

TRO

LPA

NEL

DRA

WIN

G

(4)

5/8"

(16mm

) DIA

.BO

LT H

OLE

S

6700 Best Friend Rd. Norcross, Ga 30071 (770) 447-4443 Fax (770)447-0230 Bulletin: 28-128 7/01/2005

Model CC Pumps Materials of Construction

BULLETIN: 28-184EFFECTIVE: JUNE 26, 2003SUPERSEDES: DEC. 13, 2000

6700 Best Friend Rd. Norcross, GA 30071 (770) 447-4443 Fax (770) 447-0230

OPERATION

To prevent overheating and pump failure a thermalrelief valve is installed in each pump casing, dischargehead, or discharge piping. The valve will automaticallysense the rise in temperature and discharge some ofthe hot fluid allowing cooler fluid to enter the pumpcasing. The valve will then close. On factory builtpump systems, the thermal relief valves are piped to acommon discharge tube. After installation, thisdischarge tube should be continued to a nearby drain. The discharge tube should be piped in a manner thatdischarge or leaks are visible to maintenance personnel.

SPECIFICATIONSPressure Rating: 600 psi

Temperature Setting: 140 F

MATERIALS OF CONSTRUCTIONBody: Brass

Internal Seal: VitonExternal Seal: Buna

Spring: Stainless SteelMounting Connection: 3/8 MPT

Tubing Connection: 1/4 FPT

MECHANICALTHERMAL

PURGE VALVE

DOMESTIC

PRESSURE REGULATING & CHECK VALVE ANGLE TYPE

PRESSURE REGULATING AND CHECK

VALVE COMPONENT PARTSITEM DESCRIPTION

1 VAVLE BODY2 SEAT3 DISC4 SPACER WASHER5 DIAPHRAM WASHER6 STEM LOCK NUT7 STEM8 COVER9 COVER BEARING

10 SPRING11 COVER PLUG12 DIAPHRAM13 COVER BOLT14 DISC GUIDE15 DISC RETAINER16 CHECK VALVE17 ORIFICE18 PRESSURE REGULATING PILOT19 STRAINER20 NEEDLE VALVE OPTIONAL

6700 Best Friend Rd. Norcross, Ga 30071 (770) 447-4443 Fax (770)447-0230 Bulletin: 27-812.2 10/27/2005

2" & largervalves areflanged

6700 Best Friend Road Norcross, GA 30071 Phone: 770-447-4443 Fax: 770-447-0230 http://www.syncroflo.comEffective: August 4, 2010

NSF 61 Butterfly Valve

Features:

Pressure Rating: Bi-directional or dead end service, bubble-tight shut off, 250 psig.

Pressure Profile Disc: Assures minimum torque and longer seat life.

One-Piece Thru Stem: Blow out proof, ensures dependability and positive disc positioning.

Seat Face: Negates need for flange gaskets. Valve interior completely isolated from the body.

Supported Stem Seal: Blow out proof with packing gland to prevent entry of external substances.

Materials of Construction Body: Cast Iron Disc: Nylon 11 Coated Ductile Iron Seat: EPDMStem: 416 Stainless Steel

Pressure Switch

STANDARD FEATURES

Single Switch Output Tamper-Resistant Set Point Lock Small Fixed Deadband UL listed, CSA Certified and

CE Compliance to Low Voltage and Pressure Equipment Directive

Polished Stainless Steel Sanitary Connection

SPECIFICATIONS Wetted Materials: Nickel Plated Brass Operating Temp.: -40 to 160oF

Set Point: 1% of adjustable range Proof Pressure: 600psi

Enclosure: NEMA 4X

6700 Best Friend Rd. Norcross, Ga 30071 (770) 447-4443 Fax (770)447-0230 Bulletin: 29-124 6/30/2005

6700 Best Friend Road Norcross, GA 30071 Phone: 770-447-4443 Fax: 770-447-0230 http://www.syncroflo.comEffective: August 4, 2010

Pressure Transmitter DigitalOverview The 40-801 is a high quality all stainless steel media isolated Pressure Sensor intended for use in the measurement of liquids compatible with stainless steel. 40-801 pressure sensors and transducers have been designed specifically for applications with demanding performance requirements.

40-801 sensors and transducers high strength stainless steel sensing element is machined from a solid piece of stainless steel, resulting in construction that contains no silicone oil, no welds and no internal O-rings.

Features High Accuracy High Strength Stainless Steel Construction No Silicone Oil. No Internal O-rings, no welds

(50 PSI & above) Wide operating temperature range Fully welded case provides rugged design Compatible with wide range of gases and liquids Suitable for high shock and vibration applications Superior signal clarity compared to analog

transmitters

Detailed Specifications Performance @ 25C (77F) Environmental Data

Accuracy: Stability:

Over Range Protection: Burst Pressure:

Pressure Cycles:

100 Million

TemperatureOperating:

Storage:Thermal Limits

Compensated Range:TC Zero:

TC Span:

-40 to 85C (-40 to 185F) -40 to 125C (-40 to 250F)

0 to 55C (30 to 130F)

6700 Best Friend Road Norcross, GA 30071 Phone: 770-447-4443 Fax: 770-447-0230 http://www.syncroflo.comEffective: August 9, 2010

Mitsubishi F-700 VFD

Control Specifications

Control System High carrier frequency PWM control (V/F control)/optimum excitation control/simple magnetic flux vector control Output Frequency Range 0.5 to 400Hz

Frequency Setting Resolution 0.01HZ

Frequency Accuracy Within 0.01% of the set output frequency

Starting Torque 120% (3Hz) when set to simple magnetic flux vector control and slip compensation

Acceleration / Deceleration Time Setting 0 to 3600s (acceleration and deceleration can be set individually), linear or S-pattern acceleration/deceleration mode can be selected

DC Injection Brake Operation Frequency (0 to 120Hz), operation time (0 to 10s), operation voltage (0 to 30%) variable

Stall Prevention Operation Level Operation current level can be set (0 to 150% adjustable), whether to use the function or not can be selected Protective / Warning Function Overcurrent during acceleration, overcurrent during constant speed, overcurrent during deceleration, overvoltage during acceleration, overvoltage during constant speed, overvoltage during deceleration, inverter protection thermal operation, heatsink overheat, instantaneous power failure occurrence, undervoltage, input phase failure, motor overload, output side earth (ground) fault overcurrent, output phase failure, external thermal relay operation, PTC thermistor operation, option alarm, parameter error, PU disconnection, retry count excess, CPU alarm, power supply short for operation panel, 24VDC power output short, output current detection value over, inrush resistance overheat, communication alarm (inverter), analog input alarm, internal circuit alarm (15V power supply), fan fault, overcurrent stall prevention, overvoltage stall prevention, electronic thermal prealarm, PU stop, maintenance timer alarm*1, parameter write error, copy operation error, operation panel lock

Operational Environment

Ambient Temperature -10C to +50C (non-freezing)

Ambient Humidity 90%RH or less (non-condensing)

Storage Temperature -20C to +65C

Atmosphere Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt, etc.)

Altitude, Vibration Maximum 1000m above sea level, 5.9m/s or less (conforms to JIS C 0040)

Pum

pin

gS

ys

tem

So

lutio

ns

Syn

cro

Flo

6700

Bes

t Fr

iend

Roa

d -

Nor

cros

s, G

A 3

0071

(770

) 447

-444

3 -

Fax

(770

) 447

-023

0

Pum

pin

gS

ys

tem

So

lutio

ns

Syn

cro

Flo

6700

Bes

t Fr

iend

Roa

d -

Nor

cros

s, G

A 3

0071

(770

) 447

-444

3 -

Fax

(770

) 447

-023

0

Syn

cro

Flo

, In

c.

*

*

P u m p i n g S y s t e m S o l u t i o n s

SyncroFlo6700 Best Friend Road - Norcross, GA 30071

(770) 447-4443 - Fax (770) 447-0230

SyncroFlo, Inc.

Features and Benefits

1. The vessel is ASME code (Section 8. Div. 1, UG 90 C-2) and NB stamped for 125 PSIG*. Maximum temperature is 240 F (consult the factory for higher temperatures). Nominal volume is 132 gallons. 2. The tanks shell is made of Steel. The bladder is FDA approved Heavy Duty Butyl. 3. The 100% draw down design of the tank prevents the bladder from rupturing at any storage volume or pressure within its ratings. This provides maximum water storage at all conditions. 4. The vertical design and bottom water connection eliminate water stagnation in the tank, making it ideal for drinking water use. 5. The specially designed distribution tube allows the tank to be fully pre-charged with air at the factory. 6. Water is kept inside the bladder while air is between the bladder and the tank shell. This keeps water rust free and protects the tank from corrosion. 7. Tank dry weight: 330 Lbs.

* Available in higher pressures ( 150, 200, 250 PSIG )

6700 Best Friend Rd. Norcross, Ga 30071 (770) 447-4443 Fax (770)447-0230

Bulletin: 28-153.3 7/20/2007 Supersedes: 10/02/06

Model 132 HYDROCUMULATOR TANK

WARRANTY

The components of each SyncroFlo water pressure booster system, when purchased as regular factory selections, are warranted against failure due to defects in design, material, or construction, from date of factory shipment within the periods and under the conditions noted below: PUMPS All SyncroFlo pumping assemblies are warranted against mechanical failure for a period of one (1) year. If any component of the pumping assembly fails within this period, SyncroFlo, Inc., will, at its option, repair or replace the pumps assembly on a no charge exchange basis FOB factory, Atlanta, Georgia. MOTORS Motors, when equipped with standard SyncroFlo over-temperature protection systems and maintained according to factory instructions, are warranted for one (1) year. SyncroFlo, Inc., will make, at its option, a no charge repair or replacement at the factory or at an authorized motor service station. PRESSURE REGULATING VALVES Pressure regulating valves are warranted for one (1) year. If any mechanical component of the regulating valve fails within this period, SyncroFlo, Inc., will, at its option, repair or replace regulating valve component parts on a no charge exchange basis FOB factory. COMPLETE SYSTEM The complete SyncroFlo system as a whole, including all accessories and components not mentioned above, is warranted functionally and mechanically for a period of one (1) year from date of installation or 18 months from date of shipment (whichever comes first), when installed, operated, and maintained in accordance with the Companys recommendations. SyncroFlo, Inc., is responsible only for repairing or replacing its products in accordance with the terms and conditions set forth above. There are no warranties, either expressed or implied, extending beyond those stated on the face hereof, and SyncroFlo, Inc., expressly disclaims all other warranties, including any implied warranties of mechanical ability or fitness for a particular purpose. SyncroFlo, Inc., also disclaims any liability whatsoever for incidental or consequential damages, including damages to property, damages for loss of use, loss of time, loss of profits, loss of income, or any other incidental or consequential damages. SyncroFlo, Inc., neither assumes nor authorizes any other person to furnish any warranties, or assume for it any liability in connection with the sale of its products. This warranty does not include mechanical seals, gauges, transportation, or labor costs for exchange or installation of repaired or replaced material. Final determination of warranty shall be made only by the factory upon return and inspection of returned material. No material is to be returned without a return material authority (RMA) tag which may be obtained by calling or writing the factory, advising what will be shipped and the reason for the return.

6700 Best Friend Road, Norcross, GA 30071 Phone: (770) 447-4443 Fax: (770) 447-0230

www.syncroflo.com BETTER CONTROL THROUGH SYSTEMS ENGINEERING