Festo Tecsup DGP

Force sensor

FP 1130

Measuring range: 0 200 N Measuring error: 1 % of full-scale value Sensitivity (nominal): 1 mV/V Overload: 130 % of measuring range Breaking load: 200 % of measuring range Distance moved under nominal load (calibration in pressure direction): 0.1 mm

max. Bridge resistance (full bridge): 350 (nominal) Supply voltage, permissible: 3 10 V AC/DC

Motor controller

Festo Tecsup DGP

FP 1120

Motor output: 20 V DC/300 mA Remote input: 10 V DC Position input: 0 24 V DC Proximity sensor inputs: 24 V DC/30 mA Positioning accuracy: 5 %

Measuring bridge amplifier

FP 1130

Power consumption: 50 mA Complementary resistors: 350 Bridge supply voltage: 5 V DC Amplifier input range: 10 mV Amplifier output range: 5 V Amplification: Approx. 500

Non-contact inductive-magnetic proximity sensor

Festo Tecsup DGP

FP 1120

For mounting on the slide unit (Order no. 080824). Including cable.

Power supply: 10 30 V DC Switching capacity: 6 W Overcurrent trip: Min. 250 mA Switching accuracy: 0.1mm

Pneumatic-electrical converter

TP 201, BIBB-EP, FP 1130 (until 2004)

The pneumatic-electrical converter can fulfill 3 functions: Pressure switch, vacuum switch, and differential pressure switch.

Pneumatic technical data

Design: Prestressed metal bellows initiator Pressure ranges:

Pressure switch, connector P1: 25 800 kPa (0.25 8 bar) Vacuum switch, connector P2: -20 -80 kPa (-0.2 -0,8 bar)

Differential pressure switch: connectors P1...P2: -95 800 kPa (-0.95 8 bar) Hysteresis: Maximum 25 kPa (0.25 bar)

Electrical technical data

Switching current: 400 mA

Festo Tecsup DGP

Positioning slide

FP 1110, FP 1120

The positioning slide allows measurement of position and range for proximity switches. Magnetic holders allow a vernier caliper (Order no. 035653) to be mounted. This increases the accuracy of measurements. When ordering the positioning slide on its own, please also order 4 plug-in adapters (Order no. 323571) for mounting on the aluminium profile plate.

Slide travel: 150 mm Graduation: 1 mm Angular scale: 90 Graduation: 2 Vernier scale: 0.2 mm Max. clamping thickness: 5 mm

Optical sensor with optical fiber connector, block-shaped

Festo Tecsup DGP

FP 1110

Type of light: Red light, 660 nm Switching output: PNP, normally opened/closed, exclusive OR Nominal switching distance (with fiber-optic cable ES, Order no. 150505): 80

mm Nominal switching distance (with optic-optic cable RT, Order no. 150506): 30

mm Hysteresis (referred to nominal switching distance: 10 % Reproducibility: 10 % Maximum switching current: 250 Hz Polarized, short-circuit-proof: Yes

Optical sensor, Type M18

FP 1110

Type of light: Red light, 660 nm Switching output: PNP, normally open Nominal switching distance: 150 mm Hysteresis (referred to nominal switching distance):

Festo Tecsup DGP

Pressure manifold

FP 1130

The side connector of the pressure manifold has an L plug-in coupling, the other connectors have self-closing plug-in couplings.

Pressure range: 0 1600 kPa (0 16 bar)

Set of circular weights

FP 1130

Consisting of 10 disk weights at 1000 g each.

Festo Tecsup DGP

Pressure switch

FP 1130

Design: Pneumatic-electric signal converter Installation angle: Any

Connections

Pneumatic: Internal thread R Electrical: Appliance socket to DIN 43650 Pressure range: 100 1200 kPa (1 12 bar) Overload pressure: Short-term max. 5000 kPa (50 bar) Switching frequency: Max. 3.3 Hz Reproducibility of switching point:

Festo Tecsup DGP

FP 1110

Switching voltage (reduced brightness of the LED at 18 V): 12 27 V AC/DC Switching point accuracy: 0.1mm Volume resistance: 100 m Switching time (incl. bounce time):

Festo Tecsup DGP

Reflector unit for reflective lightbarrier

FP 1110

Diameter: 20 mm

Set of weights

FP 1120, FP 1130

Contains 5 weights from 20 to 500 g.

Festo Tecsup DGP

Spindle drive unit

FP 1120

The spindle drive unit with the geared motor (Order no. 080828) implements one-dimensional motion. Electrical drive can be controlled by a programmable logic controller or by the motor controller (Order no. 162249). When ordering the spindle drive unit alone, please also order adapters (Order no. 150519) for mounting on the aluminium profile plate.

Max. displacement: 260 mm Attachment hole pattern Top: 4 x 5.3 (40 x 40 mm), with a counterbore on

both sides for socket hand screws M5 2 x 5.1 (36 x 15 mm) Attachment hole pattern Sides: 2 x M5 (36 x 15 mm) Overall dimensions: Approx. 110 x 420 x 30 mm Guide rod diameter: 12 mm Spindle pitch : 3 mm

Ultrasonic proximity sensor,Type M18

FP 1110

Permissible operating voltage:24 V DC, 20 % Switching output: PNP, normally open

Festo Tecsup DGP

Ultrasonic emitter frequency: 215 kHz Range: 100 200 mm Hysteresis (referred to nominal value):

Festo Tecsup DGP

Air pressure reservoir

FP 1130

The accumulator can be used for the following applications:

Generation of static pressures with the aid of a one-way flow control valve Generation of larger delay times in connection with time-delay and flow control

valves Compensation of pressure fluctuations Use as reservoir in the event of sudden pressure loss

Design: Brazed brass container Type of mounting: Spring clips, retaining plate Volume: 400 ml Pressure range: 0 1600 kPa (0 16 bar)

Analog pressure sensor 1

Festo Tecsup DGP

FP 1130

Pressure range*: 0 1000 kPa (0 +10 bar) Max. perm. pressure: 1400 kPa (14 bar) Supply voltage VB: 12 30 V DC Voltage output: 0 10 V Current output: 0 20 mA Total error: 1 % of full-scale value Max. measuring frequency: 100 Hz Electrical protection: Short circuit proof, polarity reversal protection,

overvoltage-proof up to 50 V DC (short-term)

*The sensor provides a signal even if pressure

Festo Tecsup DGP

Backpressure switch

FP 1130

Bursting pressure: 200 kPa (2 bar) Switching frequency: Max. ca. 200 Hz Mech. service life: >108 switching cycles Switching performance: Max. 50 mA at 24 V DC Measuring range: 120 800 Pa (1.2 8 mbar)

Capacitive proximity switch,Type M12

FP 1110

Switching output: PNP, normally open Nominal switching distance: 4 mm Hysteresis (referred to nominal switching distance): 3 15 % Maximum switching frequency: 100 Hz Polarized, short-circuit-proof: Yes

Festo Tecsup DGP

Deflecting arm force sensor

FP 1130

Measuring range: 0 5 N Overload: 130 % of measuring range Strain gauge type: Foil SG Strain gauge resistance: 350 Max. permissible supply voltage: 10 V

Connection unit, analogue

Permissible voltage range: 22 27 V DC Reference: GND 4 analogue voltage inputs: Range: -10 V +10 V (max. 30 V), input resistance:

200 k 4 analogue current inputs: Range: 0 20 mA (max. -4 +24 mA), input voltage:

max. 30 V 2 analogue outputs: Voltage: -10 +10 V, short-circuit-proof, max. 30 V, fuse-

protected, current: max. 20 mA

Using an analogue cable (order no. 189551), the unit can also be used as an analogue connection unit for the EduTrainer PLC.

Festo Tecsup DGP

Deflecting arm

FP 1120

Item to be measured for measuring compliance dependent on load.

Counting unit

FP 1110

Input signal voltage: +15 +24 V Power consumption: 1.2 W Accuracy:

Pulse output 100 pulses/s: 6 % Pulse output 1000 pulses/s: 3 % Internal clock: 3 %

Festo Tecsup DGP

Diffuse reflective optical sensor,block-shaped

FP 1110

Type of light: IR, 880 nm Switching output: PNP, normally open/closed, exclusive OR Nominal switching distance (adjustable): 360 mm Hysteresis (at nominal switching distance): 2 15 % Reproducibility: 10 % Maximum switching frequency: 250 Hz Polarized, short-circuit-proof: Yes

Gear motor

FP 1120

The motor drives for the spindle drive unit (Order no. 080824) and can be used in combination with the assembly kit DE (Order no. 150539) as a rotary drive. Includes mounting.

Festo Tecsup DGP

Rated current: 0.3 A Output rating: 3.31 W Nominal speed: 158 min-1 Motor starting torque: 60.75 Ncm Nominal torque: 19 Ncm

Inductive analog distance sensor

FP 1120

Permissible operating voltage:15 30 V DC Voltage output: 0 10 V Load resistance: 4.7 k Current output: 0 20 mA Load resistance: 500 Measuring range: 3 8 mm Max. measuring frequency: 80 Hz Temperature error: 5 % of full-scale value Linearity error: 3 % of full-scale value Reproducibility: 2 % of full-scale value Polarized, short-circuit-proof: Yes

Festo Tecsup DGP

Inductive proximity sensor,Type M12

FP 1110

Switching output: PNP, normally open Nominal switching distance (for S 235 JR): 4 mm Hysteresis (referred to nominal switching distance): 1 15 % Maximum switching frequency: 400 Hz Polarized, short-circuit-proof: Yes

Inductive proximity sensor,Type M18

FP 1110

Switching output: PNP, normally open Nominal switching distance (for S 235 JR): 5 mm Hysteresis (referred to nominal switching distance): 1 15 % Maximum switching frequency: 500 Hz Polarized, short-circuit-proof: Yes

Festo Tecsup DGP

Linear potentiometer, 300 mm stroke

FP 1120

Suitable for slide unit (Order no. 80824). Assembly with mountable vernier caliper (Order no. 150536) with the aid of the assembly set ( Order no. 150540).

Permissible operating voltage*: 13 30 V DC Potentiometer resistance: 5 k Electrical pick-up length: 304 mm Output voltage*: 0 10 V DC Max. linearity error: 0.07 % of full-scale value Resolution and reproducibility: 0.01 mm Polarity protection: Yes Adjustment speed: 10 m/s Adjustment acceleration: 200 m/s2

*Applicable for potentiometer including impedance converter.

Mountable vernier caliper

FP 1120

The mountable vernier caliper with digital display (Order no. 150540) can be mounted on the positioning slide (Order no. 080824). Delivery including battery (Type CR 2032, Li-Mn 3 V).

Measuring path: 286 mm Measuring accuracy: 0,03 mm Resolution and repeat accuracy: 0.01 mm

Festo Tecsup DGP

Speed:

Festo Tecsup DGP

Hysteresis: 0.1 1.5 mm Maximum switching frequency: 1000 Hz Polarized, short-circuit-proof: Yes

On-off valve with filter regulating valve

TP 101, BIBB-P, TP 201, TP 301 (until 2004), TP 220

Filter regulator with pressure gauge, on-off valve, quick push-in connections and quick couplings, mounted on a swivel support.

The filter with water separator removes dirt, pipe sinter, rust and condensate. The pressure control valve regulates the supply air pressure to the set operating pressure and compensates pressure fluctuations. The filter bowl has a condensate drain valve. The on-off valve pressurises and vents the entire control system. The 3/2-way valve is actuated by a rotary knob.

Type: Sintered filter with water trap, piston regulating valve Standard nominal flow rate*: 750 l/min Input pressure: max. 1600 kPa (16 bar) Working pressure: max. 1200 kPa (12 bar) Grade of filtration: 40 m Condensate quantity: 14 cm3 Connector: G 1/8, QS-6, for plastic tubing PUN 6 x 1

*Input pressure: 1000 kPa (10 bar), operating pressure: 600 kPa (6 bar), differential pressure: 100 kPa (1 bar).

Festo Tecsup DGP

One-way flow control valve

TP 101, TP 102, BIBB-P, TP 111, FP 1130 (until 2004)

The one-way flow control valve is a combination of flow control valve and a nonreturn valve. The cross-section of the restrictor can be set by means of a knurled screw.

Design: Combined flow control valve Pressure range: 30 1000 kPa (0.3 10 bar) Nominal flow rate

in flow control direction: 0 180 l/min in open direction: 180/110 l/min (Throttle valve open/closed)

Optical analog distance sensor

FP 1120

Current output: 4 20 mA Measuring range with fiber-optic cable (adjustable via potentiometer): 8 40

mm Response time:

Festo Tecsup DGP

One-way light barrier, receiver

FP 1110

Type of light: IR, 880 nm Switching output: PNP, normally open/closed, exclusive OR Nominal switching distance: 10 m Operational switching distance (adjustable): 0 8.1 m Hysteresis (referred to nominal switching distance):

Festo Tecsup DGP

Optical fiber for diffuse reflective optical sensor

FP 1110

Diameter of fiber-optic cable: 1 mm Length: 1000 mm Bending radius: >25 m Nominal switching distance: with Order no. 167 065: 30 mm

One-way flow control valve

TP 101, TP 102, BIBB-P, TP 111, FP 1130 (from 2005)

The one-way flow control valve is a combination of a flow control valve and a nonreturn valve. The cross-section of the restrictor can be set by means of a knurled screw.

Design: Combined flow control valve Pressure range: 30 1000 kPa (0.3 10 bar) Nominal flow rate

in flow control direction: 0 180 l/min in open direction: 180/110 l/min (Throttle valve open/closed)

Festo Tecsup DGP

Optical fiber for one-way light barrier

FP 1110

Diameter of fiber-optic cable: 1 mm Length: 1000 mm Bending radius: >25 m Nominal switching distance: with Order no. 167 065: 80 mm

Force sensorMotor controllerMeasuring bridge amplifierNon-contact inductive-magnetic proximity sensorPneumatic-electrical converterPositioning slideOptical sensor with optical fiber connector, block-shapedOptical sensor, Type M18Pressure manifoldSet of circular weightsPressure switchReed switchSet of test objectsReflector unit for reflective lightbarrierSet of weightsSpindle drive unitUltrasonic proximity sensor,Type M18Plug-in adapter setFunction generator/counter/stopwatchAir pressure reservoirAnalog pressure sensor 1Analog pressure sensor 2Backpressure switchCapacitive proximity switch,Type M12Deflecting arm force sensorConnection unit, analogueDeflecting armCounting unitDiffuse reflective optical sensor,block-shapedGear motorInductive analog distance sensorInductive proximity sensor,Type M12Inductive proximity sensor,Type M18Linear potentiometer, 300 mm strokeMountable vernier caliperInfrared light barrier, block-shapedNon-contact inductive-magnetic proximity sensorOn-off valve with filter regulating valveOne-way flow control valveOptical analog distance sensorOne-way light barrier, receiverOne-way light barrier, transmitterOptical fiber for diffuse reflective optical sensorOne-way flow control valveOptical fiber for one-way light barrier