FEPipe 7 NozzlePRO 9 Installation

7/23/2019 FEPipe 7 NozzlePRO 9 Installation

1/18

. .

PAULINRESEARCH GROUP

,

. ,

.


2/18

. .

PAULIN RESEARCH GROUP IS NOT LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR

OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE FURNISHING, PERFORMANCE OR USE OF THIS MATERIAL.

It is the policy of Paulin Research Group to enforce all rights relating to protection of this

information. The information contained in this document is proprietary in nature and may not be

reproduced, copied or divulged in whole or in part without the prior written consent of Paulin Research

Group. This document is provided pursuant to the terms of a contract, order or confidentiality agreement.

Unauthorized distribution or disclosure of its contents is a violation of that contract, order or agreement

and persons doing so may be liable for penalties as provided by law.

Copyright 1991-2015 Paulin Research Group. All Rights Reserved.

Paulin Research Group

11211 Richmond Avenue, Suite 109

Houston, Texas 77082

USA

Phone: +1 (281) 920-9775

Fax: +1 (281) 920-9739

E-mail: [email protected]

Web: www.paulin.com


3/18

. .

FEPipe v7.0 and NozzlePRO v9.0 System Requirements

Operating System

An important note, Microsoft discontinued support for Windows XP on April 8, 2014. Please be advised

that PRG, commencing with FEPipe version 7.0 and NozzlePRO version 9.0 no longer includes theWindows XP operating system in test platforms.

32-bit or 64-bit versions (including International):

Microsoft Windows 7

Microsoft Windows 8

Microsoft Windows 8.1

Microsoft Windows Server 2003



Permission

To perform an installation you must have Local Administrator privileges

To use the software once installed, you do not need Local Administrator privileges; however

restricted users require read/write permission on the PRG2015 installation folder

Computer and Processor Minimum Requirements

2.0 GHz Dual Core processor or higher 2 GB of RAM

512 MB graphics card

PRG graphics need access to the actual adaptor. Any attempt to run in a virtualized environment is unlikely to

work properly.

CD-ROM drive (installation CD) or Internet connection (Download)

Available, enabled USB port (Key Server or Single User installations)

Computer and Processor Recommended Requirements

3.1 GHz+ Dual Core processor or higher

16 GB of RAM

Hard Disk

40 GB of available disk space


4/18

. .

Installing Your PRG Software

This install document is written for FEPipe v7.0 NozzlePRO v9.0, originally released in September

2014.

The installer will build a complete C:\PRG\PRG2015 folder. You do not need an existing installation to

install this build.

The FEPipe 7.0 NozzlePRO 9.0 installer is bundled into a PRG2015.zip file. The PRG2015.zip file

contains:

Setup_PRG2015.EXE (program installer)

After the PRG2015.zip download is complete, extract the contents to a folder on the host computer.

The Setup_PRG2015.EXE is a bootstrapper executable that extracts the MSI, checks prerequisites,

downloads dependencies and configures install environment. Both network and non-network users musthave a full program installation on their computer. The Setup_PRG2015.EXE must be run on all users

computers that require access to any PRG software program. Network drives are only supported for data

files. FEPipe 7.0 NozzlePRO 9.0 must be installed on the end users computer.

To begin installation you must have Administrator privileges to the host computer and a live internet

connection. The Setup_PRG2015.EXE installer will not execute unless started with full Administrator

privileges and will not complete without an internet connection.

The installer will check if Micrsoft.NET 4 or Visual C++ 2010 is installed on your computer. PRG2015

requires both as prerequisites for installation. If it is missing, the installer pings Microsoft for download.

Navigate to folder where the Setup_PRG2015.EXE was extracted

If you do nothave Administrator, privileges please follow these steps. Alternatively, restart Windows and

login with an Administrator account.


5/18

. .

If you have full Administrator, privileges please skip to page.

Right click on PRG Software Installer.EXE

Choose Run as

Run As screen will appear

Choose The following user: and fill Administrator account information

Choose OK


6/18

. .

FEPipe 7.0 NozzlePRO 9.0 installer begins

Before FEPipe 7.0 NozzlePRO 9.0 program files are installed. The installer will run a diagnostic check

on your computer to determine if the required prerequisites are installed. FEPipe 7.0 NozzlePRO 9.0

require Microsoft NET 4.0 framework and Visual C++ 2010. If both are present the installer will begin

FEPipe 7.0 NozzlePRO 9.0 installation.

However, if either Microsoft NET 4.0 or Visual C++2010 are not present the installer will ping the

Microsoft website for download.

Follow prompts through installer


7/18

. .


8/18

. .


9/18

. .


10/18

. .


11/18

. .


12/18

. .

Select FINISH and the installer will now begin FEPipe 7.0 NozzlePRO 9.0 installation.


13/18

. .

Follow prompts through installer


14/18

. .

The installer will ask you to agree to the license terms.


15/18

. .

In the next step, the installation location can be modified to a location of your choice. The defaultinstallation directory is C:\PRG\PRG2015. You will see the installer shows the location listed as C:\PRG\.The installer will automatically build the subfolder C:\PRG\PRG2015. You do not need to type" \PRG2015" into the installer entry text box

PRG Software uses Microsoft DirectX graphics. This requires that the program(s) be installed into adirectory without any blank spaces or non-standard characters.

Examples of good installation paths:

C:\PRG2015\PRG

C:\FEA\Workgroup\PRG_FEPipe_PipingChecklist

Examples of badinstallation paths:

C:\Program Files\PRG2015\PRG (blank space)C:\192.168.10.\PRG 2015 (decimal points, blank space)\\MyServer\MyShare\PRG\PRG2015 (Universal Naming Convention (UNC) paths)


16/18

. .

The program file installation is now ready to start. Select Install


17/18

. .

Files begin to copy to designated installation folder. This will take several minutes to complete.


18/18

. .

When all files have been installed a final screen will appear. Select Finish to complete.

The FEPipe 7.0 NozzlePRO 9.0 installation is now complete.

FEPipe 7 NozzlePRO 9 Installation

Documents

Transcript of FEPipe 7 NozzlePRO 9 Installation