Federal Mogul Bearing India Ltd. Training On

Study of Bearings

Mechanical Engg. Deptt.

JMIT,Radaur(YNR)DEEPAK KUMAR

91-8950783197

FMBIL

In 1979,FEDERAL MOGUL BEARINGS INDIA LTD.

Formely FMBIL and ANAND ENGINE COMPONENTS Diversified into the manufacture of thin wall engineBearings.The engine bearing division was set up in Collaboration with Federal mogul Corporation,USA,And world leaders in the thin-wall bimetal Engine Parwanoo in the state of HIMACHAL PRADESH.

MISSION OF COMPANY !!!

CUSTOMER DELIGHT - BY Providing superior products on time every time.

SHARE HOLDER DELIGHT - BY Providing better than market returns on investments.

QUALITY POLICY !!

Federal mogul power train is commited to providing product and services that meet or exceed our customer`s requirement by maintaining a management system.

Quality Excellence !!! Driving the Future of Federal - Mogul

Customer Satisfaction• Poviding our customer with product and services that meet or exceed their requirments.

Continual Improvement• Measurable improvement of the effectiveness of

our quality management system.

SAFETY• Providing a safe work environment for our employees and visitors.

•SUPPLY CHAIN MANAGEMENT•ENGINEERING DEPTT.•POWDER PLANT•SANDING & ANNEALING SECTION•PLANT1 (MANUAL PLANT SECTION)•PLANT2 (TOOL ROOM SECTION)•PLANT4 (AUTOLINE 1 SECTION)•PLANT5 (AUTOLINE 2 )•PLANT6 (ALL VENDORS)•PLATING SECTION•MAINTENANCE•QUALITY AUDIT DEPARTMENT•METALLURGICAL LAB.•GAUGE ROOM•PACKING DEPARTMENT•DISPATCH SECTION•SINTER LINE

•PLAIN SLEEVE BEARING. FLANGE BEARING. •WASHERS. BUSHES

TransmissionBush

Main bearing

Connecting rod bearing

Flange bearing

Type of bearings

1. Plain sleeve Bearing.

Type of bearings

3. Washers. 4. Bushes.

Engine bearingsBearings are devices used to transmit loads between relatively moving surfaces.

Bearings are used in all types of machinery, engines and mechanisms for

supporting and controlling the motion of the rotating, sliding or reciprocating

parts. Shafts, spindles or axles usually support the rotating parts. Bearings are

designed to serve the purpose with minimum friction, power loss, and

generation of heat and are aided in their requirement by suitable lubricants.

Bearings are used in Automotive, Industrial, Agricultural, Earth Moving, Marine

and Stationary Engines among others. Bearings that support the rotating shaft in

a fixed position against loads acting perpendicular to the axis of shaft only are

called Radial Bearings. Those that support against loads parallel to the axis of

the shaft are called Thrust Bearings, while those, which resist both radial and

thrust loads, are called Angular or Radial-Thrust Bearings.

Places where the bearings are used in engine?

Powder Plant

It consists of a crucible made of silicon carbide, which is surrounded by refractory bricks. There is gap between the refractory bricks called the annular gap. Burners using mixture of compressed air and atomized diesel heat this crucible, commonly known as ‘pouring crucibles’.

Sinter line

Sintering is a process of bonding solid particles by atomic forces. Sintering forces tend to decrease with increase in temperature but obstruction to sintering viz. incomplete surface contact, presence of surface films and lack of plasticity decreases much more with increase in temperature. Thus increase in sintering time or temperature results in stronger bond and greater tensile strength. But sintering must be carried out at a temperature below the melting point of the constituent element with least melting point.

MANUFACTURING OF BEARINGS

Blanking and stampingBlanking is defined as the process of cutting the strip into pieces of desired

length and these pieces are called blanks. Stamping is defined as the process of

punching the desired data (part no., Coil no.) on the blanks.

Both processes are carried out on the same machine know as blanking

machine. It consists of three parts – decoiler, straightner and blanker. The coil is

brought to the blanking machine after slitting. It is then mounted on the decoiler.

It uncoils the coil and pushes it into the straightner.The straightner has the function of straightening the strip and pushing it into the blanker. On the straightner there is a limit switch which controls the amount of strip passing through the straightner.

Thank You