Face Milling - Winstar CuttingFace Milling CXSN / SNMX1205 Nickel contain plating applied for...
Transcript of Face Milling - Winstar CuttingFace Milling CXSN / SNMX1205 Nickel contain plating applied for...
B062
Unique "Type Z" geometry minimizes chatter and vibration!!! 獨特的刀口幾何設計將平面銑削的震動頻率最小化
.CXSN Face Mill Series is one of innovations that provides more available cutting edges by doublesided insert and longer tool life for our customers.
.Unique “Type Z” design and special cutting edge guarantees lowest cutting loads and longest tool life.
.Negative inserts makes it even stronger and higher performance while machining various working material.
Type Z features.Sharper cutting edge.
.Low cutting resistance.
.Positive land and rake angle.
.Excellent chip evacuation.
SNMX1205 Inserts features.Double sided.
.Total 8 cutting edges.
.Less interference and contactwith the unused corner.
Z
45°
CXSN / SNMX1205 平面銑削
Face Milling
CXSN / SNMX1205
♦ ♦
Nickel contain plating applied for excellent corrosion resistance effect also increase surface hardness.To avoid the strain in second processing, finishing will be done after pre-harden.
Customize available.
CXSNF
Order No. D L d T ap InsertsScrew Wrench
ICXSNF04-050220 50 40 22 4 6
SNMX1205 TS4015 TK15
ICXSNF05-063220 63 40 22 5 6
ICXSNF05-063254 63 40 25.4 5 6
ICXSNF06-080270 80 50 27 6 6
ICXSNF06-080254 80 50 25.4 6 6
ICXSNF07-100320 100 50 32 8 6
ICXSNF07-100317 100 50 31.75 8 6
ICXSNF08-125400 125 63 40 10 6
ICXSNF08-125381 125 63 38.1 10 6
ICXSNF10-160400 160 63 40 12 6
ICXSNF10-160508 160 63 50.8 12 6
ICXSNF14-200476 200 63 47.625 14 6
ICXSNF14-200600 200 63 60 14 6
B064
ap
平面銑削
Face Milling
SNMX1205
Working Material Vc fz ap
Carbon Steel (HB85-225) 80 ~ 200 0.10 ~ 0.30 ~ 6.0
Stainless 300 Series 50 ~ 110 0.08 ~ 0.25 ~ 3.6
Cast Iron (HB140-220) 80 ~ 180 0.10 ~ 0.30 ~ 6.0
Recommended Cutting Conditions
♦♦♦♦
Total 8 cutting edges per insert. (SNMX 1205)Low cost effective and high efficiency for general purpose face milling. Low cutting force action due to the extremely positive geometry. Wide wiper flat for better surface finish.
B065
平面銑削刀片
Milling Inserts & Tools
Face Milling
SNMX 1205-MG ✓ ✓ ✓ 12.7 1.5 6.4 - 6 -
SNMX 1205-RG ✓ ✓ ✓ 12.7 1.5 6.4 - 6 -
P Steel ◎ ◎ ◎ ○ ○
1st choice 2st choiceM Stainless steel ○ ○ ○ ◎ ◎
K Cast iron ◎ ○ ○ ○ ○
Inserts Designation
Grade Dimensions (mm)
Drawing
CX21N
SC
X31NA
CX31N
SC
X41NS
CX41N
AA B S r d1 t1
Specification