F810A - MTL Instruments · 20V Input 24V Input 28V Input Input vs Output Current - Simplex F801...
4
March 2017 EPS F810A Rev 1 Technical data MTL fieldbus networks Eaton Electric Limited, Great Marlings, Butterfield, Luton Beds, LU2 8DL, UK. Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283 E-mail: [email protected] www.mtl-inst.com © 2017 Eaton All Rights Reserved Publication No. EPS F810A Rev 1 March 2017 1 The F810A fieldbus power system is designed to provide redundant FOUNDATION™ fieldbus power for Foxboro EVO™ control systems using FBM228 modules. Eight fieldbus segments are supported. The system comprises a baseplate which accommodates two redundant pairs of Foxboro FBM228 modules and two MTL-Relcom F801 or F802 power modules operating in redundant configuration. Failure alarms, galvanic isolation, power conditioning and segment termination are incorporated into each F80x module. In applications requiring simplex power, a single F80x module may be used. For extreme reliability, the module baseplate has no components and only provides interconnections between FBM228 modules, the power modules and external connections. Each F80x module has indicator LEDs to show both its status and that of the eight segments under power. In normal operation, each green ‘Segment’ LED is lit, showing that the segment is powered. If a segment is shorted, this LED is extinguished, and the red ‘Alarm’ LED is lit. In the alarm condition, a normally closed, galvanically-isolated relay contact goes to an open condition. Connections to the alarm relay are made via screw terminals on the F810A baseplate. If multiple F810A units are used, a common alarm circuit can be achieved by ‘daisy-chaining’ the alarm circuits. The F80x module provides galvanic isolation between the 24V DC input power and the fieldbus segments, as required by the IEC61158-2 fieldbus standard and the Fieldbus FOUNDATION™ F810A Integrated Redundant Fieldbus Power for Foxboro EVO TM Control Systems FF-831 validation test for power conditioners. There is also galvanic isolation between the fieldbus segments, thereby preventing multiple segment failures from ground faults on more than one segment. Each segment has its own fieldbus power conditioner and current limitation. Termination of the fieldbus segment is automatically maintained when single or redundant F80x modules are fitted. An F809F-Plus diagnostic module may optionally be installed on the carrier, to automatically collect and distribute diagnostic information on each of the eight fieldbus segments. Measured parameters may be viewed in the Foxboro control system by either assigning the F809F-Plus as a fieldbus device to segment 1 or 8 of the powered segments, or by means of a separate fieldbus segment. Connections for the separate segment are provided on the baseplate. For more information see the F809F-Plus product specification. Redundant 24V DC (nom.) input power can be connected to the F810A baseplate using Foxboro I/A standard AMP connectors. F80x power modules and the F809F-Plus fieldbus diagnostic module can either be powered from the same source or, alternatively, for installations in which standard Foxboro power supplies are unable to provide sufficient current capacity, an external 24V DC supply may be connected. Field wiring connections are available with either pluggable screw terminals (F810A-PS) or pluggable spring clamp terminals (F810A-PC). Accessories are required for T-section and G-section, DIN-rail (DMK01) or surface (SMS01) mounting. FOUNDATION™ fieldbus is a trademark of Fieldbus FOUNDATION ™ , Austin, Texas. • Integrated redundant fieldbus power for FBM228 FOUNDATION™ fieldbus modules • 8-segment redundancy • High-density, compact design • Fully isolated • Low power dissipation • No components on carrier • Built-in “smart” termination • Continuous physical layer diagnostic option
Transcript of F810A - MTL Instruments · 20V Input 24V Input 28V Input Input vs Output Current - Simplex F801...
March 2017EPS F810A Rev 1
Technical data MTL fieldbus networks
Eaton Electric Limited, Great Marlings, Butterfield, LutonBeds, LU2 8DL, UK.Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283E-mail: [email protected]
© 2017 Eaton All Rights ReservedPublication No. EPS F810A Rev 1March 2017
1
The F810A fieldbus power system is designed to provide redundant FOUNDATION™ fieldbus power for Foxboro EVO™ control systems using FBM228 modules. Eight fieldbus segments are supported. The system comprises a baseplate which accommodates two redundant pairs of Foxboro FBM228 modules and two MTL-Relcom F801 or F802 power modules operating in redundant configuration. Failure alarms, galvanic isolation, power conditioning and segment termination are incorporated into each F80x module. In applications requiring simplex power, a single F80x module may be used.
For extreme reliability, the module baseplate has no components and only provides interconnections between FBM228 modules, the power modules and external connections.
Each F80x module has indicator LEDs to show both its status and that of the eight segments under power. In normal operation, each green ‘Segment’ LED is lit, showing that the segment is powered. If a segment is shorted, this LED is extinguished, and the red ‘Alarm’ LED is lit. In the alarm condition, a normally closed, galvanically-isolated relay contact goes to an open condition. Connections to the alarm relay are made via screw terminals on the F810A baseplate. If multiple F810A units are used, a common alarm circuit can be achieved by ‘daisy-chaining’ the alarm circuits.
The F80x module provides galvanic isolation between the 24V DC input power and the fieldbus segments, as required by the IEC61158-2 fieldbus standard and the Fieldbus FOUNDATION™
F810AIntegrated Redundant Fieldbus Power for Foxboro EVOTM
Control Systems
FF-831 validation test for power conditioners. There is also galvanic isolation between the fieldbus segments, thereby preventing multiple segment failures from ground faults on more than one segment. Each segment has its own fieldbus power conditioner and current limitation. Termination of the fieldbus segment is automatically maintained when single or redundant F80x modules are fitted.
An F809F-Plus diagnostic module may optionally be installed on the carrier, to automatically collect and distribute diagnostic information on each of the eight fieldbus segments. Measured parameters may be viewed in the Foxboro control system by either assigning the F809F-Plus as a fieldbus device to segment 1 or 8 of the powered segments, or by means of a separate fieldbus segment. Connections for the separate segment are provided on the baseplate. For more information see the F809F-Plus product specification.
Redundant 24V DC (nom.) input power can be connected to the F810A baseplate using Foxboro I/A standard AMP connectors. F80x power modules and the F809F-Plus fieldbus diagnostic module can either be powered from the same source or, alternatively, for installations in which standard Foxboro power supplies are unable to provide sufficient current capacity, an external 24V DC supply may be connected.
Field wiring connections are available with either pluggable screw terminals (F810A-PS) or pluggable spring clamp terminals (F810A-PC). Accessories are required for T-section and G-section, DIN-rail (DMK01) or surface (SMS01) mounting.
Foundation™ fieldbus is a trademark of Fieldbus FOUNDATION™, Austin, Texas.
• Integrated redundant fieldbus power for FBM228 Foundation™ fieldbus modules
• 8-segment redundancy
• High-density, compact design
• Fully isolated
• Low power dissipation
• No components on carrier
• Built-in “smart” termination
• Continuous physical layer diagnostic option
F810AMarch 2017
2
ELECTRICALEMC Compliance
To EN61326:2013 Electrical equipment for measurement, control and laboratory use - EMC requirements
F810A - BLOCK DIAGRAM
ENVIRONMENTAL
Ambient temperature F801 F802Operating (full load) - 40°C to +65°C - 40°C to +50°COperating (60% load) - 40°C to +65°C - 40°C to +65°CStorage - 40°C to +85°C - 40°C to +85°C
Note: Temperature range applies only when mounted on a horizontal DIN rail attached to a vertical surface.
Ingress protectionIP20 to BS EN60529 (For additional protection mount the equipment in an enclosure)
PHYSICAL NETWORKSIEC61158-2ISA-S50.02 Part 2-1992FOUNDATION™ fieldbus H1
ORDERING INFORMATION
DESCRIPTION PART NO.Carrier, unpopulated F810A-CA
8-segment power module: 21.5V, 350mA F8018-segment power module: 28V, 500mA F802
F810A system with pluggable screw terminal connectors and two F801 modules
F810A-PS
F810A system with pluggable screw terminal connectors and two F802 modules
F810A-2-PS
F810A system with pluggable spring clamp connectors and two F801 modules
F810A-PC
F810A system with pluggable spring clamp connectors and two F802 modules
F810A-2-PC
Blanking module * F800-BLK
Fieldbus diagnostic module F809F-Plus
DIN-rail mounting kit, T or G section (pack of 40 clips)
DMK01
Surface mounting kit (pack of 40 clips) SMS01
* Used in place of an F80x power module for non-redundant operation in order to defeat the failure alarm caused by the absence of the F80x.
Note: Foxboro FBM228 modules are not included and must be obtained separately.
SPECIFICATIONLocation of equipment
Safe area
INPUT F801 F802
Input voltage (DC) 19.2 - 30.0V 19.2 - 30.0V
Current consumption(24V input, all outputs fully loaded) 4.4A* 6.9A*
Total Power dissipation(24V input, all outputs fully loaded)
42W* 46W*
* Redundant operation(Figures based upon fully populated F810A baseplate, including all F80x, FBM228 and F809F -Plus modules - see also next page)
OUTPUT F801 F802
Number of channels Eight (8) Eight (8)Voltage (DC) 21.5V - 24.0V 28.0V - 30.0VDesign current (per segment) 0 to 350mA 0 to 500mACurrent limit > 370mA > 520mAMinimum load 0mA 0mAIsolationFieldbus to input power: 250V AC rms withstandSegment to segment: 200V DC withstand
ALARMSAlarm contact rating
1A maximum @ 30V DC maximumAlarm contact status
Normally closed
Alarm threshold F801 F802Segment output <19V DC <24V DC
SYSTEM CONNECTIONSFoxboro ‘Fieldbus’ LAN
9-way subminiature D, femaleAddress switchesFieldbus wiring
Segment 1–8 and diagnostic segment – each has 3-way pluggable connector in screw terminal or spring clamp version, 0.14 to 2.5mm2
(See ordering information)Foxboro primary and secondary power inputs
2 x 3-way socket headers type AMP Universal MATE-N-LOKAlternative power inputs
2 x 4-way pluggable connector, 0.14 to 2.5mm2(Note these connectors are spring clamp type for -PC and -PS product variants. (See ordering information)
Chassis ground and screen/shield ground Separate M4 terminal studsAlarm contacts
2-way fixed screw terminal connector, 0.14 to 2.5mm2
MECHANICALMounting method DIN-rail or vertical flat panel. DIN-rail mounting requires mounting clips (quantity 9 per F810A), available as part number DMK01 for pack of 40 clips.Weights
F801: 1.45kgF802: 1.50kg F810A-CA: 0.55kg
�
�
�
�
�
�
�����
���
��������
�� ��
�������
�������
������ ������������������ ����
�����������
���� �
���
���
������
�����
���
���������������
���� �
���
���
������
�����
���
��������������
����������� ��
������������ ��
��������������
� ����
� ����
� ����
� ����
�� �
�����
����
���
�� ������������
�� ������������
� ����������������������
������ �����������������
�������������
Baseplate I.D.Sw.1 Sw.2
0 ON ON1 ON OFF2 OFF ON3 OFF OFF
Posn. Sw.31 - 4 ON5 - 8 OFF
F810AMarch 2017
3
F801 PARAMETERS
Power Dissipation - Simplex F801 System
8.00
10.00
12.00
14.00
16.00
18.00
20.00
0 100 200 300 400
Average Segment Output Current (mA)
Pow
er D
issi
patio
n (W
)
20V Input24V Input28V Input
Input vs Output Current - Simplex F801 System
0.50
1.50
2.50
3.50
4.50
0 100 200 300 400
Average Segment Output Current (mA)
Mod
ule
Inpu
t Cur
rent
(A)
20V Input24V Input28V Input
Input vs Output Current - Redundant F801 System
0.50
1.50
2.50
3.50
4.50
150 200 250 300 350 400
Average Segment Output Current (mA)
Mod
ules
Inpu
t Cur
rent
(A)
20V Input24V Input28V Input
Power Dissipation - Redundant F801 System
12.00
14.00
16.00
18.00
20.00
22.00
150 200 250 300 350 400
Average Segment Output Current (mA)Po
wer
Dis
sipa
tion
(W)
20V Input24V Input28V Input
a) b)
c) d)
F802 PARAMETERS
Input vs Output Current - Simplex F802 System
0
1
2
3
4
5
6
7
8
0 100 200 300 400 500 600
Average Segment Output Current (mA)
Mod
ule
Inpu
t Cur
rent
(A)
19V Input24V Input30V Input
Power Dissipation - Simplex F802 System
4.0
9.0
14.0
19.0
24.0
29.0
0 100 200 300 400 500 600
Average Segment Output Current (mA)
Pow
er D
issi
patio
n (W
)
19V Input24V Input30V Input
Power Dissipation - Redundant F802 System
4.0
9.0
14.0
19.0
24.0
29.0
0 100 200 300 400 500 600
Average Segment Output Current (mA)
Pow
er D
issi
patio
n (W
)
19V Input24V Input30V Input
Input vs Output Current - Redundant F802 System
0
1
2
3
4
5
6
7
8
0 100 200 300 400 500 600
Average Segment Output Current (mA)
Mod
ule
Inpu
t Cur
rent
(A)
19V Input24V Input30V Input
a) b)
c) d)
Calculating current requirements
There are two separate methods of powering the F80x power modules on the baseplate - Option 1 - from the Foxboro Power system or - Option 2 - from External Power supplies. Both methods can provide redundant power to the F810A.
Note: Power for the FBM228 modules is always taken from the Foxboro power supplies.
Option 2 current requirement from either external supply:1. Use the 801/802 a) graph for simplex operation or
the b) graph for redundancy.2. Add 0.08A for the F809F-Plus - if fitted.Option 1 current requirement from Foxboro supply:Add a total of 0.8A for four FBM228 module to Option 2 current.
�����
���������
�����
���������
��
Linking alarm circuits
F810AMarch 2017
The given data is only intended as a product description and should not be regarded as a legal warranty of properties or guarantee. In the interest of further technical developments, we reserve the right to make design changes.
Eaton Electric Limited, Great Marlings, Butterfield, LutonBeds, LU2 8DL, UK.Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283E-mail: [email protected]
© 2017 Eaton All Rights ReservedPublication No. EPS F810A Rev 1 010317March 2017
EUROPE (EMEA):
+44 (0)1582 723633 [email protected]
THE AMERICAS:
+1 800 835 7075 [email protected]
ASIA-PACIFIC:
+65 6645 9864 / 9865 [email protected]
4
DIMENSIONS (mm)
1
1c1a
16c
16a
1c 1a
16c
16a
LABEL
PID
CO
N11
1C
ON
141
CO
N12
4
CO
N12
1
CO
N50
9
CO
N13
1C
ON
21
CON505
SW1
CO
N11
9
CO
N24
CO
N20
CO
N11
7
CO
N41
CO
N12
0
CON506
CO
N51
0
CO
N11
CO
N11
8C
ON
18
CO
N17
CO
N19
CO
N31
CO
N50
7
1
13
ON
1c 1a
16c
16a
1
1c1a
16c
16a
1c 1a
16c
16a
1c1a
16c
16a
31
1c1a
16c
16a
1c 1a
16c
16a
1
SEGM
ENT8 -S+
SEGM
ENT7 -S+
SEGM
ENT6 -S+
SEGM
ENT5 -S+
+S
-
SEGM
ENT4
+S
-
SEGM
ENT3
-S+
SEGM
ENT2
-S+
SEGM
ENT1
FOXBORO POWER B
POW
ER M
ODULE A
POW
ER M
ODULE B
FIELDBUS
FIELDBUS
FOX 24V
EXT 24VB-
+-
++
-+
-FO
X 24VEXT 24VA
ALARM
H1- H1S H1+
-1H+1H S1H
A2
A1
MODULEDIAGNOSTIC
DIAGNOSTIC SEGMENT
DIAGNOSTIC SEGMENT
FOXBORO POWER A
A
1 2 3
OFF
FBM SEG
1-4 1
FBM SEG
5-8 2FBM
SEG 1-4 2
FBM SEG
5-8 1
B
SCREEN/SHIELD
GROUND
CHASSISGROUND
1
1 CON26
CON27REDUNDANT FOUNDATION FIELDBUS POWER SYSTEM
F810A - CA
F809
F-PL
US
260
300
148
135 1155
145
145
5
F80x module top panels showing indicators
2
2
Country Authority Standard Certificate Approved for Ratings
– Fieldbus FOUNDATION™ FF-831PS001700 (F801) PS001900 (F802)
H1 Profile - 132 –
APPROVALS - for the latest certification information visit www.mtl-inst.com/support/certificates/
